I am mainly used to the enterprise where most connections are deployed by some "normal" kind of fiber eg SFP+, QSFP+, SFP28, QSFP28 and those modules are almost fool proof, run cool and are reliable. Like most normal admin users, I like to use my own hardware for routing and switching rather than the often poor equipment provided by the ISP, especially when you have enterprise hardware that will be more reliable. The normal path is that you would just take the fiber op........

Most relevant config points from my video here. 1.) Create a new End User The most important part is setting the "Digest Credentials", that is the password that the phone will use to authenticate.........

Before starting you should reset your phone(s) if they have been previously registered to another CME/CUCM: https://realtechtalk.com/Cisco_IP_Phone_How_To_Reset_To_Factory_Settings_Instructions_CP_9971_8800_8900_8845_8851_8841_8831_7961_7960_7945_7942_7941_7940-2212-articles........

This is a quick overview of the main screens that you will need to go through to do the Cisco Unified Communication Manager installation (CUCM). Skip the media test ........

In our example below, we create 2 hunt groups. You could assume the #1 group is sales and #2 group is support etc.. and you can create more as needed. The main part of hunt is the "list" option where you add each phone number that is to be part of the group ephone-hunt 1 sequential pilot 2001 list 1234 timeout 10 ephone-hunt 2 sequential pilot 2002 list 5678 tim........

#Remember that you need a valid gateway IPunless the Asterisk server is on the same subnet and LAN Set Valid Gateway IP (if you don't have one already) ip route 0.0.0.0 0.0.0.0 GATEWAYIP Enable VOIPTrust voice service voip ip address trusted list ipv4 0.0.0.0 0.0.0.0 sip Set Credentials For Asterisk and Register To Asterisk sip-ua........

This is how we configure outside PSTNaccess or dialing through another SIPtrunk. Beware that this a simplistic example that neglects most security including SRTP First you'll need to be in config mode: Step - 1 Enter Voice Service VOIP security options There are more options but for now we'll just focus on security/allowing connections to and from our phones and the trunk. Router(config)#voice service voip ........

Since newer versions of Ubuntu like 20, you will find there is no longer dynagen and that the dynamips provided is faulty and will segfault each time: Cisco Router Simulation Platform (version 0.2.14-amd64/Linux stable) Copyright (c) 2005-2011 Christophe Fillot. Build date: Apr 3 2018 12:20:29 Local UUID: 3c1c0b7f-2fab-4fda-b40b-74841d1bcfe0 Instance ID set to 1. netio_tap_create: unable to open TAP device tap1 (No such fi........

This should work for most console ports of other manufacturers too. It is a quick and simple method for emegencies or deploying a few appliances/devices in a non-standard environment or small environment. However, if this is a route thing, or the equipment is not physically close to you, it would be best to use some sort of "Terminal" server which is an IP connected switch with several serial ports built-in for this purpose. Normally they accessible by web/........

Just hit **# on the keypad and the CIPCwill enable the button in settings for a factory reset. Sometimes the phone may run into issues or may be unable to register to another tftp server (eg. another CME or CUCM server) due to a bug or maybe due to the security settings tying it to a specific server. Step 1 - Click Settings Step 2 - Hit "**#"........

Router#show license Index 1 Feature: ipbasek9 Period left: Life time License Type: Permanent License State: Active, In Use License Count: Non-Counted Lic........

1.) Make sure your conf register is 0x2102 Do show version and at the very end of the output you will see the Configuration register. show version Configuration register is 0x2102 If the config register is not 0x2102 then enter this command: r1#configure terminal r1(config)#config-register 0x2102 r1(config)#end 2.) Let's Erase the NVRAM/flash........

It is a bit different and annoying here for these types of routers/models as you need to physically remove the CF (Compact Flash) and only then, will it enter ROMMON mode (Ctrl + Pause remotely over the console will not do it for us). This means you cannot do this remotely, or at least not without the help of a remote/physical helper. Step 1.) Power off, router and remove CF Disk Slot#2 Go to the router and remove the slot#2 cover uses your hand or it may help to use a........

If you are in enable mode and make a typo, the router will treat it as a domain name and try to resolve it, and if it can't resolve it, you'll have to wait until it times out. Here's how to solve the Translating domain server error in Cisco Enter this in config mode: no ip domain-lookup Be sure to sav........

How To Fix This Cisco Switch/Router Error %Error opening tftp %Error opening tftp://10.0.2.2/network-confg (Permission denied) %Error opening tftp://10.0.2.2/cisconet.cfg (Permission denied) %Error opening tftp://10.0.2.2/router-confg (Permission denied) %Error opening tftp://10.0.2.2/ciscortr.cfg (Permission denied) %Error opening tftp://10.0.2.2/network-confg (Perm........

It may appear to be an Xorg or lightdm/gdm/mdm error but in reality for many users with this issue, it's a driver conflict and issue. I had a system that had two GPUs, an Intel and Nvidia GPU. The only thing that got it working was to remove the nouveau driver and blacklist it so it never came back, then the Intel GPU works fine without these issues. Solution sudo rmmod nouveau add nouveau/other driver to blacklist edit th........

This assumes that you've already installed the relevant HWIC cards eg. Cisco Asynchronous Serial NIM These are essentially cards that you install into your router, once installed you connect an Async cable to one of the ports on the card which normally gives you 8 console cables and are normally labelled 1 through 8. You connect all of the cables to the devices you need (even non-Cisco devices) whether switches, routers or firewalls, they will usually work. The real m........

This was done on a 2900 but applies to all the switches of the same era. Step 1 - Power Cycle and enter recovery mode If you have physical access you can power cycle and hold the mode button down for 15 seconds. After that the SYS light will flash on the switch and you will see the following screenshot. If you don't have physical access (eg. it is a datacenter swich over console only) then power cycle and hit "Ctrl+Pause/B........

A lot of older devices either support telnet or very old SSH keyx algorithms which are insecure and disabled by all newer/modern SSH clients for security reasons. However, sometimes you may be on a LAN via VPNor some other secured network or for whatever reason, absolutely, need to connect to this device and sometimes old/embedded devices may not be possible to update to a newer SSH server. If you run into this you may be using a modern/newer SSH client and get thi........

It is common that you may get access to undocumented equipment and need to reset the password. This applies to many Cisco routers whether 2600, 2900, 3900 etc... Cisco's Guide says to hit Ctrl +Pause/Break but if it doesn't work on some devices causing people to say "cisco password reset pause break does not work", you can see Cisco's alternative key combinations here:........

This tutorial will get your router up and running using emulation tools. In this case we'll be getting a Cisco C7206 (C7200 series) VXR router going which also supports SCCP VOIP services. dynamips is the emulator itself and dynagen is the front-end tool that helps us control everything. It is used by tools such as gns3 and eve-ng. Together the two tools (dynamips and dynagen) allow us to create and emulate REAL router........

Video Links: How To Setup 2 Phones on a Single CME Router and get the GUI going. How to use Dialpeers with CME with two routers How to implement call restrictions using COR / Class of Restriction Set your clock: HH:MM:SS clock set 22:00:00 24 September 2024........

This would be crucial especially if the phone is hardened, not being able to reset or change settings could prevent a phone registering in a new environment or even when migrating from office to office. This applies even if you are trying to migrate the phone to another platform such as Asterisk/FreePBX etc... This guide applies to nearly all of the Cisco IP phones that you would use in CME or CUCM from several years ago including models: 9900, 9971, 8800, 8900, 8845, 8851, 8841........

Install Errors on Version 12: This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5 on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error. *Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install. What really causes this even though you successfully install........

The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........

There are multiple layers but most are enabled by default such as the setting in the Phone Device Settings. However the one not enabled by default is the one in "Enterprise Phone Configuration". Enable "Cisco Camera" and then reboot your phones to enable it.........

DN = Directory Number: It is basically the extension of the phone In the example below, 55 is a DN assigned to the phone.........

Install Issues: How to Make CUCM iso /modify to work on non-VMWare machines like QEMU/Xen/OpenStack If you get kernel panic errors in VBOX usually disabling Nested Paging will fix the issue (thanks to Mark). ks_pre.sh error is caused by having the wrong VDX pattern (change it do sd per guide link above) and/or the wrong VMSpecs (Cisco req........

In most of the Cisco router IOS I find the ports like ge0/0 ge0/1 and ge0/2 or whatever your ports are down. They will not even give you a link light. So one of the first tasks should be getting the port you are working with up. In my case the first goal is often connectivity with the LAN and WAN. LAN = your local area network (eg. in the office/home ) WAN= your ISP/public internet (eg. fiber/cable/dsl/ethernet).........

00:55:07: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down 00:55:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up Switch(config)#no logging console ........

Switch#show ip dhcp snooping Switch DHCP snooping is disabled DHCP snooping is configured on following VLANs: 1 Insertion of option 82 is enabled circuit-id format: vlan-mod-port remote-id format: MAC Option 82 on untrusted port is not allowed Verification of hwaddr field is enabled Interface&nb........

Enter configuration console: enable configure terminal This is important because if your console doesn't look like below none of the commands will work! Switch(config)# Save and Apply Settings wr Show Switch Configuration: show run Show Port List/Sta........

This works on the 2000 and 3000 series generally. *The easy way is to just hold the mode button for 10+ seconds. The full/proper way is below: 1.) Either power on the unit and hold the "mode" button or hold the "mode" button until you see the below: 00:04:08: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram 00:04:08: %EXPRESS_SETUP-6-CONFIG_IS_RESET: The configur........

The key thing is that you must use a "machine"id of "pc-1.3" or it will say your hardware is not supported. Additionally you MUST use a virtio disk or you will get a ks_pre.sh error as soon as the install starts (a look at logs will show it can't find a disk). This is funny because even though the OS finds the disk and an fdisk -l shows it, it looks like the script looks for a /dev/vda device (virtio) and nothing else, so if you didn't use Virtio as you........

Cisco's CUCM (Cisco Unified Communication Manager) is a system that combines voice, video, data and mobile products into a single unified management suite. At its core, the CUCMis like a "Super PBX" that controls the flow of all communications through an organization even single or multiple site deployments. Cisco's CUCMmakes communication more effective and simple through centralized management and unification of communications resources.........

yes it does create its own json ============================================ cat /tmp/vcsaUiInstaller/ovftool-20180809-175238948-20180809-175603497.log |grep -i json 2018-08-09T17:56:04.238-07:00 verbose OVFTool[30966] [Originator@6876 sub=Default] Manifest file entry: SHA1(VMware-vCenter-Server-Appliance-6.7.0.12000-8832884_OVF10-file1.json) = 1deb658c724767697587d5909c4051c01813e6a1 --> ........

The first is a dual CPU AMD Opteron 2373EE (4 cores x 2) and I think it did bad because it has some old 250GB SATAs which can only do about 65MB/s max sequential reads. I think it should have blown away the second (AMD X4 640 Quad Core). [root@fs12home unixbench-4.1.0-wht-2]# ./Run make all make[1]: Entering directory `/root/unixbench-4.1.0-wht-2' Checking distribution of files ./pgms exists ./src exists........

In file included from drivers/block/cciss.c:1015: include/asm-generic/pci-dma-compat.h: In function `cmd_special_free': drivers/block/cciss.c:196: sorry, unimplemented: inlining failed in call to 'cciss_tag_discard_error_bits': function body not available include/asm-generic/pci-dma-compat.h:25: sorry, unimplemented: called from here make[2]: *** [drivers/block/cciss.o] Error 1 make[1]: *** [drivers/block] Error 2 make: *** [drivers] Error 2........

This was unbelievable how much the Xen kernel slows things down, keep in mind both tests were done on the hostnode, one was with the Openvz-Xen hybrid kernel and the other was just OpenVZ. You can see the performance difference is nearly 300% better when not using the Xen kernel. OpenVZ-Xen Kernel Test Results (I was wondering what was wrong/so slow with my Core i5!) # # # # # #&n........

Here are the results, it is Sempron 3000+ AMD Mobile, 500Gig HDD, 512MB RAM with shared ATI Radeon graphics. # # # # # # # ##### ###### # # #### # # # # ## # # # #&nb........

The results are still not flattering and are nothing close to native performance. Unless GlusterFS has a "DRBD-like" option to delay writes over the network and to only read from the client side, I don't see how performance can ever improve much more. After doing some client optimizations Iadded more to the score: Start Benchmark Run: Sun Nov 29 00:37:44 PST 2009 00:37:44 up 3 min, 1 user, load average: 0.01........

You might remember my original GluserFS/OpenVZ benchmark which produced a horrible 29.8 This is the exact same system, but using the latest 2.0.8 (with some small files patch which speeds up performance) you can see it is about 25% faster. I also haven't tuned my config files at all, but there are some settings that should increase performance on small files which I believe i........

This is very disappointing since GlusterFS markets itself as a solution to deploy VPS servers on. On the HNitself I get a Unixbench of about 360. I'm also using an SSH tunnel to secure the communications, but even before that, things seemed very slow. # # # # # # # #####&n........

I've had an old Blackberry for a few years and I was ready to spend some serious cash on a nice Nokia. I love the idea of the Linux based Symbian S60 OS, so I was looking at phones like the E63, E71 (both are basically the same, at least CPU/screensize although E71 is thinner, has a 3MP camera, has GPS, and has dedicated buttons to adjust the volume). Then Iheard about the N97 and what a revolution it was supposed to be and it was even compared to iPhone. To........