• How to kill a docker swarm


    Assign way more replicas than you have of memory on all nodes and watch the Swarm crash which can easily reproduce in a small VMfor testing. root@Deb11Docker01:~# docker ps CONTAINER ID IMAGE COMMAND CREATED STATUS PORTS NAM........
  • Docker dockerd swarm high CPU usage cause solution


    If you have swarm services and dockerd is creating a high load even with the containers just being idle, the easiest solution is to upgrade to a newer docker version. For example an identical config of 3 nodes, with Redis 5 with 30 replicas produces a load of about 1.45 in Debian 10 with Docker18.09.1 If I create the same setup on Debian 11, with Docker 20.10.5+dfsg1 then the CPU usage is low. One other difference I wondered is the kernel. In my test setup........
  • How to use the FTDI USB serial cable to RJ45 adapter to connect to the console on Cisco/Juniper Switch Router Firewall in Linux Ubuntu Debian Redhat


    This should work for most console ports of other manufacturers too. It is a quick and simple method for emegencies or deploying a few appliances/devices in a non-standard environment or small environment. However, if this is a route thing, or the equipment is not physically close to you, it would be best to use some sort of "Terminal" server which is an IP connected switch with several serial ports built-in for this purpose. Normally they accessible by web/........
  • RHEL 8 CentOS 8, Alma Linux 8, Rocky Linux 8 System Not Booting with RAID or on other servers/computers Solution for dracut and initramfs missing kernel modules


    This seems to have changed for RHEL 8 where a normal dracut to update your initramfs creates a system that only boots for the running kernel. For example if you have Kernel 5 and then chroot into a RHEL 8 variant which uses kernel 4.18, and run dracut, it seems that by default the system will be unbootable. It is also the case that if you move your RAID array or drives to another server that it will be unbootable, because dracut seems to only include modules needed for the curre........
  • Cisco UC CME How To Enable Licensed Features


    Router#show license Index 1 Feature: ipbasek9 Period left: Life time License Type: Permanent License State: Active, In Use License Count: Non-Counted Lic........
  • Cisco Switch / Router How To Restore Factory Default Settings


    1.) Make sure your conf register is 0x2102 Do show version and at the very end of the output you will see the Configuration register. show version Configuration register is 0x2102 If the config register is not 0x2102 then enter this command: r1#configure terminal r1(config)#config-register 0x2102 r1(config)#end 2.) Let's Erase the NVRAM/flash........
  • HongKong VPS Server, Cloud, Dedicated Server, Co-Location, Datacenter The Best Guide on Hong Kong, China Internet IT/Computing


    In our 2024 VPS Server/Cloud Buyer's Guide, we place the location of your VPS/hosting/server as one of the priorities that is often overlooked. 2024 Update - Datacent........
  • VirtualBox VBox Nat Network Handing Out Wrong IP Address Subnet Solution


    This seems to be an ongoing issue that is still reproducable in the latest Ubuntu Vbox 6.x. The default NAT Network range is usually 10.0.2.0/24. If you change this range it does not seem to work properly. Say we change the range to 10.50.1.0/24 If you get a new lease you will find that you get an IP from the old range but the default gateway is from the new range. ........
  • Juniper JunOS Command Overview and Howtos Switch, Router, Firewall Tutorial Guide


    Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........
  • How To Get Started on Ubuntu with gpt-2 OpenAI Text Prediction


    apt install software-properties-common add-apt-repository ppa:deadsnakes/ppa apt update apt install python3-pip apt install python3.7 curl gnupg python3.7-dev git ln -s /usr/bin/python3.7 /usr/bin/python3 pip3 install numpy keras_preprocessing curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add - echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........
  • How To Install python 3.4 3.5 and up on Linux with wine - Working Solution


    This is sure simple if you follow the guide but it took a lot of hacking around to make this work on Debian/Ubuntu! Now before you ask why bother running wine and python, the reason is because Python executables are NOT cross-platform. If you run pyinstaller in Linux, that binary will only run on Linux and the same if you do it in Windows. So it is preferable if you have a single environment that you can create Linux and Windows binaries from rather than running 2 separate........
  • ADATA USB Thumb Drive Issues


    This is the reason that I don't like the new ADATA USB drives such as the UV128/64GB or 128GB drives and other ones that look to be the same style (the green sliding USB connector). They just don't work well from new and never work properly at any point. [ 788.242463] usb 1-1.2: new high-speed USB device number 16 using ehci-pci [ 788.339816] usb 1-1.2: New USB device found, idVendor=125f, idProduct=db8a [ 7........
  • Cannot Print PDF Solution and Howto Resize


    If you can print other PDFs but not a particular one it is very likely that the PDF size is A4 (the longer, skinnier Asian paper size) instead of the North American letter size ( 8.5" x 11"). This breaks printing in most cases. Or it may print if you find a program that ignores the size issue. Here is an example of an A4 being rejected by a printer in Ubuntu Linux via CUPS Cannot print PDF CUPS Samsung C460: Processin........
  • Cisco Unified Communications Manager / CUCM IP 8.6,10,12 Install Error Solution


    Install Errors on Version 12: This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5 on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error. *Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install. What really causes this even though you successfully install........
  • Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM


    The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........
  • PHP Issues With Decoding Strange Smart Quotes And Non-Standard ASCII Characters


    When using strip_tags and html_entity_decode with PHPit often breaks and produces annoying diamonds with question marks. It is probably because of characters like these: … (looks like 3 dots but it is a single weird character). ’ (looks like a normal apostraphe but it is not) ” (looks like a normal double quote but it is not). An easy way to sort this out is to copy the above and search in an ASCII table to extend the functional........
  • Adobe Acrobat Reader for Linux to use and view XFA Fillable Forms


    The reason for not being able to read one of these dreaded/ fillable "XFA" forms is because no Linux PDF reader that I'm aware of supports them. Part of this reasoning is for security. It is really silly, they should ban these XFA forms or at least replace the Please Wait with the non-fillable version. Download Adobe Reader 9.5 for Linux from here: This is the solution but only so much, at least for me I was able to view th........
  • Python and BeautifulSoup4's BS4's Decompose Method To Remove Unwanted Inner Tags


    < a href="/Products/MX72244"> < span class="c-shca-icon-item__body-name-brand"> ADATA < / span> &nbs........
  • How Does Cisco CUCM (Cisco Unified Communication Manager) Work?


    Cisco's CUCM (Cisco Unified Communication Manager) is a system that combines voice, video, data and mobile products into a single unified management suite. At its core, the CUCMis like a "Super PBX" that controls the flow of all communications through an organization even single or multiple site deployments. Cisco's CUCMmakes communication more effective and simple through centralized management and unification of communications resources.........
  • Linux Kernel USB Export Errors


    4.374647] usb_common: exports duplicate symbol usb_get_dr_mode (owned by kernel) [ 4.403334] usbcore: exports duplicate symbol __usb_get_extra_descriptor (owned by kernel) [ 4.427736] xhci_hcd 0000:00:15.0: xHCI Host Controller [ 4.427844] xhci_hcd 0000:00:15.0: new USB bus registered, assigned bus number 1 [ 4.429040] xhci_hcd 0000:00:15.0: hcc params 0x200077c1 hci version 0x100 quirks 0x01109810 [ 4.429141] xhci_hcd 0000:00:15.0: cache line size of 64 is not sup........
  • Debian Mint Ubuntu compiling xmr-stak


    sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........
  • VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI


    #mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........
  • SMF Forums / Simple Machines Forums Not Displaying Images Theme or Styles Properly using 127.0.0.1


    This is one thing that has me wondering about SMF. It is apparently a known issue but in the latest version and new install nothing looked right because it was using http://127.0.0.1 to find everything! How on earth would it ever do this or think it is normal? Excerpt of crazy html code it produces that causes the issue: ........
  • pcimodules and lspci not working alternative solution


    pcimodules no longer works it produces nothing probably because the format of /sys/bus/pci is different. lspci -k doesn't work on older lspci versions. pciutils can be compiled but it won't work if you have an old system and compile on a newer glibc. iteriate through /sys/bus/pci/devices/*/modalias cat /sys/bus/pci/devices/*/modalias pci:v00008086d00001237sv00000000sd00000000bc06sc00i00 pci:v00008086d00007000sv0000000........
  • kdenlive - No LADSPA plugins were found! Check your LADSPA_PATH environment variable. [producer_xml] failed to load transition "qtblend"


    This happens if you are running a kdenlive script from the shell of a remote machine without using SSH "-X" forwarding and it will also cause any areas where you write text to be a white screen for that duration. melt FusionFestival.kdenlive No LADSPA plugins were found! Check your LADSPA_PATH environment variable. [producer_xml] failed to load transition "qtblend" [producer_xml] failed to load transition &q........
  • ffmpeg trouble concatenating similar but different files


    When things go wrong your video is basically unplayable or the first video plays fine and then freezes when moving on to the next. Generally if both videos weren't produced with the exact 100% same settings you will have issues. You can try the basic concat but it often won't work right. Solution for me: My example uses 3 videos in total so "n=3" and a=1 to include audio. ffmpeg -threads 12 -i file1.mp4 -........
  • Centos 7 Cudaminer Nvidia setup guide


    I am using a GTX 1060 but replace the download for the driver with the correct/current version for your particular card by visiting: http://www.nvidia.com/Download/index.aspx?lang=en-us yum install automake curl openssl-devel libcurl-devel gcc gcc-c++ yum -y install kernel-devel-`uname -r` yum -y install unzip #the........
  • imagemagick pdf convert error solution - **** Warning: can't process font stream, loading font by the name. Can't find CMap Identity-UTF16-H building a CIDDecoding resource. Warning: falling back to Identity ordering **** Error reading a conte


    **** Warning: can't process font stream, loading font by the name. Can't find CMap Identity-UTF16-H building a CIDDecoding resource. Warning: falling back to Identity ordering **** Error reading a content stream. The page may be incomplete. **** File did not complete the page properly and may be damaged. **** This file had errors that were repaired or ignored. ****........
  • USB Device/MP3 Player not working properly and can't browse the device filesystem? Check the cable twice and again!


    Here is a simple MP3 player and now there's a reason to understand why the supplied cable has some kind of capacitor and is very short. These devices can be VERY finicky and any voltage fluctuation or difference is enough to cause issues. Take for example the error messages from Linux Mint: [804829.895414] usb 1-1: USB disconnect, device number 11 [806961.109030] usb 1-1: new high-speed USB device number 12 using xhci_hcd........
  • text to speech for Linux


    espeak - is horrible and sounds very old and robotic echo "hello there"|espeak #don't know how to use mbrola and plugins cicero jovie just seems to be a graphical interface to espeak There is also sbreader/sapi Google's Text To Speech Works Quite Well #!/bin/bash say() { local IFS=+;/usr/bin/mplayer -ao alsa -really-quiet -noconsolec........
  • PayPal Subscription Howto Creation Automatic Payments Manual


    An easy way to pay companies and friends/family since PayPal does not have an option when sending money to make it a subscription: "business" = The e-mail or PayPal ID of the person/organization to pay to. a3 The recurring amount "eg. 115" will be 115 USD p3 The time period (eg. 2) t3 Unit of time period m=monthly,w=weekly,y=yearly item_name = "the note/product service reason you are paying ha........
  • SAS2008 LSI 9200-E Linux Upgrade Flash Firmware with sas2flash


    Download from here http://www.avagotech.com/products/server-storage/host-bus-adapters/sas-9200-8e#downloads sudo Installer_P20_for_Linux/sas2flash_linux_i686_x86-64_rel/sas2flash -listall LSI Corporation SAS2 Flash Utility Version 20.00.00.00 (2014.09.18) Copyright (c) 2008-2014 LSI Corporation. All rights reserved &nbs........
  • HP Procurve Switch 2824 CLI Telnet Experience , Guide and Tutorial


    ------------------------------------- ProCurve J4903A Switch 2824 Software revision I.10.77 Copyright (C) 1991-2009 Hewlett-Packard Co. All Rights Reserved. RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by the Government is subject to restrictions........
  • Dell CS24,FS12 NV5 and NV7 1U Server Information & Parts


    Motherboard: Gigabyte GA-3CESL: http://b2b.gigabyte.com/products/product-page.aspx?pid=2658#dl Dell Part Numbers for the motherboard: R1232 R1232L R2232S SERVER MOTHERBOARD GENUINE 408P9 CN-0408P9 GA-3CESL Manual Download here RAMSlots: 16 (8 controlled by each CPU) RAMType: DDR2 ECC 5300P........
  • Vbox/Virtualbox devices grayed out for non-root user solution


    It is a permissions issue that is hard to fix. All but one USB device is greyed out. I am already a member of "vboxusers" I have already enabled and disabled USB support for the guest. I have already reinstalled the latest VBOx guest editions If running as root it all works fine Changing........
  • 2CO/2Checkout how to create recurring payment subscription button dynamically


    It was hard to find this as I find most online payment processors don't just put the basic information in plain view. Remember to set your sid (your seller id). The below can easily be turned into a scripted PHP template to integrate into your own custom or existing payment solution. http://help.2checkout.com/articles/How_to/How-to-Sell-Recurring-Products-with-2Checkout/........
  • heatbeat ERROR: NV failure (msgfromsteam): [>>> ] ha_msg_add_nv_depth: line doesn't contain '='


    Apr 17 11:55:47 Cluster01 heartbeat: [1426]: WARN: ha_msg_add_nv_depth: line doesn't contain '=' Apr 17 11:55:47 Cluster01 heartbeat: [1426]: info: >>> Apr 17 11:55:47 Cluster01 heartbeat: [1426]: ERROR: NV failure (msgfromsteam): [>>> ] I have never been able to reproduce the above but it happened on heartbeat-3.04-2 when Itook a node down for testing. One thing Ibelieve caused it was by configuring ha.cf........
  • Dell FS12-NV7 2U Server Information and Guide


    I've got one of these for testing projects from work at home and got more than I bargained for with the time I've spent on it due to the storage handing/Perc 6/i cards. My particular model came with the following: 2U Rack Mount Server with Rails 2xOpteron 2373 EE (Quad Core, there is a 6-core version that can be found at times) 16GB RAM 2 x 250GB Seagate SATA 2 x Dell Perc 6/i (horrible and a nightmare to work........
  • LSI MegaRAID Adventures, Guide and HowTo


    LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
  • LOG: MAIN PANIC failed to expand condition "${if eq {$authenticated_id}{}{0}{${if eq {$sender_address}{$local_part@$domain}{0}{${if match{$received_protocol}{N^e?smtps?a$N}{${perl{checkbx_autowhitelist}{$authenticated_id}}}{${if eq{$received_prot


    I experienced this with CPanel's Exim after an auto-update (a Google of this error produces lots of complaints with few clear solutions). In this case I'll put the solution at the top. Run /scripts/buildeximconf to rebuild the Exim config and it should be fine after that. mail -vs "from test" user@dest.com < .bash_history LOG: MAIN cwd=/root 4 args: send-mail -i -v user@dest.com LOG: MAIN &........
  • Asus VE247H 23.7" Inch LCD/LED Backlit Monitor Dead/Stuck Pixel Policy Complaint


    I've thought for awhile that Asus has been banking on its years old reputation for quality amongst gamers and enthusiasts and I think I'm right. My Asus VE247H Monitor with a supposed 2MS refresh rate has 1 red/stuck/dead pixel but fortunately it can only be seen on a non-true black picture or against a blue screen. I have several Asus products and find they're all of fairly poor quality. First of all their motherboards have given me the most issues of any brand, they te........
  • convert carat ^M/M Windows based text files to Linux


    carat M isn't this symbol ^ that you think, it can only be produced by typing "Ctrl-v, Ctrl-m". That you might see in text files saved from Windows. tofrodos is the package that has dos2unix which is basically the same scripts that replace ^M with /n tofrodos is the Debian/Buntu package name which has the dos2unix and unix2dos binaries........
  • CPU #1 not responding - cannot use it.


    I think this will be useful to others because I have a server that kept crashing mysteriously during intense disk usage/RAID checks. It would only crash during the weekly RAID integrity check. ThenI noticed during a reboot that not all CPUs were being brought up, as a result this actually creates much higher temperatures with the output I got from sensors, just booting the system produced higher than normal temperatures. You can imagine that a full blown RAID check........
  • Debian 5.04 RAID 1 mdadm boot problem GRUB error


    I successfully created a single RAID 1 partition which includes /boot inside it and my root directory through the Debian installer. It said GRUB installed successfully but when I try booting the OS it seems GRUB can't read anything. When trying to boot from GRUB GRUB Loading stage 1.5. GRUB loading, please wait... Error 2 I get "Error 2" when trying to boot Debian. I also notice from a LiveCD that........
  • OpenVZ user_beancounters kmemsize failcnt Processes Timing Out/Doing Nothing/Zombie


    cat /proc/user_beancounters produces the following: kmemsize 1861537 5139870 12752512 12752512 26965041 Notice the failcnt "26965041", that is for kmemsize and at first it confused me. The system had enough guaranteed and enough burst RAM available. kmemsize is a variable indepedent of that, but who cars about the explanation right, let's just make thing........
  • Javascript Get a specified element using getElementById()


    Javascript Get a specified element using getElementById()Great, it produces the value for whatever "id" is passed to the function. http://www.java2s.com/Code/JavaScript/Development/GetaspecifiedelementusinggetElementById.htm [code:1:1287ede953] function getElement(){ var x=document.getElementById("myHead........
  • Intruder detection device uses behavioural analysis


    Intruder detection device uses behavioural analysisIntruder detection device uses behavioural analysis by Antony Savvas Monday 13 June 2005 Symantec is introducing a new intrusion detection product that uses behavioural analysis to block potential attacks on enterprise networks. The new Critical System Protection 4.5 system uses technology that Symantec acquired through last year’s purchase of Platform Logic. It is designed to protect deskt........
  • Become your own ISP!


    Become your own ISP!http://waverider.com/ I would link to the exact product I am mentioning but it's under Products/5.8Ghz because I can't find the exact URL because of their annoying javascript and frames (you'll see what I mean). The exciting thing is that this unit can supposedly be up to 72mbit, it is NOT line of sight and the range is up to 20miles. I wonder how real world speeds and range would actually be and if it is reliable. I j........
  • Norton Antivirus is the worst - who would have known?


    Norton Antivirus is the worst - who would have known?http://www.software-antivirus.com/ Check the link above, that review site lists Norton as one of the ones to stay away from. With good reason too, I always wondered why Norton seemed to miss so many viruses, spyware and such. Even when it didn't, it was absolutely useless because it was either unable to delete the file and it was never able to repair or disinfect. So in essence, from my experience, N........
  • CDR Manufacturers - Why is so much media bad?


    CDR Manufacturers - Why is so much media bad?I have searched for good media and tried many kinds for years. I guess I'll try to summarize my findings and conclusions. Dye is irrelevant, dye of any color can be good or bad, it more likely depends on the manufacturer. Speaking of manufacturers, the name at the top of the disc means nothing. For example, Memorex along with any other 'brand' is actually always made by another manufaturer including CMC Mag........
  • Use Mozilla Firefox, not Internet Explorer - You'll be glad!


    Use Mozilla Firefox, not Internet Explorer - You'll be glad!Hey guys, I just thought I'd recommend that everyone switch to Mozilla Firefox as their web browser. You can find it at http://mozilla.org It is free and it is much better than IE. It has a built-in popup blocker which works great and most importantly, it doesn't have a million critical security flaws which could compromise your security such as passwords for on-line banking etc..........
  • NEC ND-3500A is great!


    NEC ND-3500A is great!I just picked up an NEC 3500A a few weeks ago and I love it. It is a great all in-one optical drive solution. It can burn DVD/+R-R at up 16x, read at 16x and rewrite at 4x and CD-R at up to 48x! Not bad, but the impotant part is that it delivers consistent high quality burns and the drive is as quiet as I could ask it to be. It's also convenient that it has a lot of hacked firmware for overspeeding of........
  • Other Security Web Sites


    Other Security Web SitesSeveral websites actively track security issues. This list provides you with the major providers of security information on the Web. Many of these organizations also provide newsletters and mailings to announce changes or security threats: Center for Education and Research in Information Assurance and Security (CERIAS) CERIAS is an industry-sponsored center at Purdue University that is focused on technology and relate........
  • Debian/Ubuntu/Kubuntu Bash/Console/Terminal/Putty Home and End Keys Don't Work or Produce a ~


    This is a very weird, annoying and bizarre quirk with many distributions, especially Debian. The home and end keys don't work, but it's a simple fix as long as you found this article :) You just have to edit /etc/inputrc: Find the commented lines as shown below: # "e[1~": beginning-of-line # "e[4~": end-of-line *If you can't find the above, just copy and paste the code below into your inputrc, it will en........
  • Unixbench Score with Glusterfs/Openvz & Quad Core Xeon - Updated with GlusterFS 2.0.8


    You might remember my original GluserFS/OpenVZ benchmark which produced a horrible 29.8 This is the exact same system, but using the latest 2.0.8 (with some small files patch which speeds up performance) you can see it is about 25% faster. I also haven't tuned my config files at all, but there are some settings that should increase performance on small files which I believe i........
  • Apple iPhone 3GS and predecessors are leading a revolution


    As much of a computer nerd as Iam, I'm usually a late adopter to technology for a few reasons. Ifeel most new hyped technologies and electronics are mainly fads, and I'm also cheap. Adopting later means you avoid the bugs, kinks and most importantly pay the lowest price, that's me being cheap again :) I never read much about the iPhone but Isaw all the hype around it and until recently I wasn't a big fan of anything Apple until a few years ago I realize........
  • BASH Decrement Does not work


    track-=1 produces track: command not found It's weird because track+=1 works just fine The solution is to used the old fashion method: track=$(($track - 1))........
  • Latest Articles

  • Cloned VM/Server/Computer in Linux won't boot and goes to initramfs busybox Solution
  • How To Add Windows 7 8 10 11 to GRUB Boot List Dual Booting
  • How to configure OpenDKIM on Linux with Postfix and setup bind zonefile
  • Debian Ubuntu 10/11/12 Linux how to get tftpd-hpa server setup tutorial
  • efibootmgr: option requires an argument -- 'd' efibootmgr version 15 grub-install.real: error: efibootmgr failed to register the boot entry: Operation not permitted.
  • Apache Error Won't start SSL Cert Issue Solution Unable to configure verify locations for client authentication SSL Library Error: 151441510 error:0906D066:PEM routines:PEM_read_bio:bad end line SSL Library Error: 185090057 error:0B084009:x509 certif
  • Linux Debian Mint Ubuntu Bridge br0 gets random IP
  • redis requirements
  • How to kill a docker swarm
  • docker swarm silly issues
  • isc-dhcp-server dhcpd how to get longer lease
  • nvidia cannot resume from sleep Comm: nvidia-sleep.sh Tainted: Linux Ubuntu Mint Debian
  • zfs and LUKS how to recover in Linux
  • [error] (28)No space left on device: Cannot create SSLMutex Apache Solution Linux CentOS Ubuntu Debian Mint
  • Save money on bandwidth by disabling reflective rpc queries in Linux CentOS RHEL Ubuntu Debian
  • How to access a disk with bad superblock Linux Ubuntu Debian Redhat CentOS ext3 ext4
  • ImageMagick error convert solution - convert-im6.q16: cache resources exhausted
  • PTY allocation request failed on channel 0 solution
  • docker error not supported as upperdir failed to start daemon: error initializing graphdriver: driver not supported
  • Migrated Linux Ubuntu Mint not starting services due to broken /var/run and dbus - Failed to connect to bus: No such file or directory solution