• Wordpress overwrites and wipes out custom htaccess rules and changes soluton


    cat .htaccess RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . index.php [L] I keep reading there is a "# BEGIN WordPress" and a "# END WordPress" in the wordpress htaccess above but there is clearly not. Even more strange is that my permissions are just 444 (read only). so i changed it........
  • Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM


    The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........
  • Cisco 2960 Switch Reset To Factory Defaults


    *The easy way is to just hold the mode button for 10+ seconds. The full/proper way is below: 1.) Either power on the unit and hold the "mode" button or hold the "mode" button until you see the below: 00:04:08: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram 00:04:08: %EXPRESS_SETUP-6-CONFIG_IS_RESET: The configuration is reset and the system will now reboot 00:04:09: %SYS-5-REL........
  • SSH error cannot Forward or Listen "bind: Cannot assign requested address"


    debug1: Local connections to LOCALHOST:18006 forwarded to remote address 192.168.1.93:8006 debug1: Local forwarding listening on 127.0.0.1 port 18006. debug1: channel 0: new [port listener] debug1: Local forwarding listening on ::1 port 18006. bind: Cannot assign requested address What we are seeing is that we can't listen on an IPV6 address of ::1. We need to tell SSH to stop using IPV6 so we'll edit ssh_config to take care of this issue........
  • Why SMART is not smart at all and doesn't properly predict disk errors that cause a kernel panic or crash


    Before getting into the output here is my typical experience with SMART, there is what I call a "bad disk" with pending and uncorrectable sectors that cannot be reallocated. It has caused a kernel panic and system crash repeatedly as we can see from the logs. But SMART says it has "PASSED" its self assessment. SMART is still useful to me but it is more about looking at Current_Pending_Sector. Any time I have had anything but 0 for that attribute it........
  • Debian Mint Ubuntu compiling xmr-stak


    sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........
  • VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI


    #mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........
  • Hard Drive Serial Number Examples


    The reason for this article is because a lot of us don't physically see our hard drives they are often remote in a datacenter etc and the actual serial number we see in SMART is not enough to check for some manufacturers. A good example is our first one the Toshiba === START OF INFORMATION SECTION === Device Model: TOSHIBA DT01ACA200 Serial Number: 33FMDW4AS........
  • Apache htaccess Custom ErrorDocument not working properly for root home page 403 Error Issue and Solution


    So I have a domain "testdomain.com". Inside test domain.com's root is the following .htaccess: Options +FollowSymLinks -Indexes ErrorDocument 403 /launch/index.html Order Deny,Allow Deny From All Allow From 192.168.1.2 When you visit anything other than root things work fine. Eg. if you visit http://testdomain.com/somedirfile.html It will show the right error in /launch/........
  • M2Crypto.SSL.Checker.WrongHost: Peer certificate subjectAltName does not match host, expected fedora-archive.ip-connect.vn.ua, got DNS:mirror.ip-connect.vn.ua


    You are using Centos 5 which is deprecated so nothing in yum will work until you follow this post to use the vault: http://realtechtalk.com/Centos_59_Working_Vault_Repo_file-1921-articles yum update Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * epel: fedora-archive.ip-connect.vn.ua Traceback........
  • kdenlive titles/text renders as white screen when using .sh script


    When using the .sh script the rendering doesn't work after an upgrade of related packages to kdenlive. kdenlive (kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1)) with affine or composite transitions was fine but is now broken during the time of transition it is just a white screen. The previous version was fine: kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1 But now I can't find it or install it:........
  • Wine uninstalled broken on Linux Mint


    Solution: Aptitude is very smart and fixed the issues it was because of nvidia cuda and opencl and nothing else suggested or hinted this using apt sudo aptitude install wine The following NEW packages will be installed: ocl-icd-libopencl1{ab} ocl-icd-libopencl1:i386{ab} wine wine1.6 wine1.6-amd64{a} wine1.6-i386:i386{a} The following packages will be REMOVED:........
  • Reading package lists... Done W: GPG error: http://ppa.launchpad.net trusty InRelease: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY D46F45428842CE5E


    Still looking for the solution Working Solution 2017/07 sudo apt-key adv --keyserver keyserver.ubuntu.com --recv-keys D46F45428842CE5E Solution gpg --keyserver hkp://subkeys.pgp.net --recv-keys D46F45428842CE5E gpg: requesting key 8842CE5E from hkp server subkeys.pgp.net gpg: keyserver timed out gpg: keyserver........
  • USB 3.0 External HDD Enclosure Seagate UAS problems - [sdd] tag#1 CDB: Write(16) 8a 00 00 00 00 01 70 04 08 68 00 00 00 08 00 00


    This is a 8TB Seagate external USB 3.0 device apparently newer kernels use a module called "UAS" instead of "USB Storage" which causes issues as a lot of devices are not properly supported in UAS mode by the kernel driver. The solution some say is to disable UAS specifically for your USB device but I'd rather just disable UAS altogether. Solution blacklist UAS: *do not do this it does not work and just causes your USB 3.0........
  • USB Device/MP3 Player not working properly and can't browse the device filesystem? Check the cable twice and again!


    Here is a simple MP3 player and now there's a reason to understand why the supplied cable has some kind of capacitor and is very short. These devices can be VERY finicky and any voltage fluctuation or difference is enough to cause issues. Take for example the error messages from Linux Mint: [804829.895414] usb 1-1: USB disconnect, device number 11 [806961.109030] usb 1-1: new high-speed USB device number 12 using xhci_hcd........
  • Linux shows my drive as being dead is it really? Buffer I/O error on device sdb, logical block 0 sd 3:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00


    Normally the below would indicate a failing or failed drive. In this case the SATA port was unplugged and sometimes the Linux kernel/motherboard even with AHCIjust don't play nice and can't handle it. What happened is Iplugged in a new drive after removing another one. However the log shows that after the old drive was plugged in the Linux kernel kept complaining thinking the drive was there but not responding properly. This continued even with reseating........
  • check if Apache uses worker MPM or prefork MPM


    apachectl -l Compiled in modules: core.c prefork.c http_core.c mod_so.c It is "prefork.c" so in httpd.conf these settings are what you would use (if you use worker.c it won't have any impact): StartServers 2 MinSpareServers 5 MaxSpareServers&nb........
  • PYCURL ERROR 22 - The requested URL returned error: 404 Not Found Solution


    # yum -y install qemu-kvm Loaded plugins: fastestmirror Setting up Install Process Loading mirror speeds from cached hostfile * base: mirror.lzu.edu.cn * elrepo: ftp.utexas.edu * epel: ftp.jaist.ac.jp * extras: mirrors.aliyun.com * openvz-kernel-rhel6: mirror.fdcservers.net * openvz-utils: mirror.fdcservers.net * updates: mirrors.nwsuaf.edu.cn Resolving Dependencies........
  • fdisk wq causes hung process


    I created a new partition table on a newly plugged in device and it caused fdisk to hang (even force kill does not work). It also may be a bad drive or some other issue because fdisk -l hangs after the first 2 HDDs (totaly of 8 HDDs on this system): [1232879.903596] INFO: task fdisk:27176 blocked for more than 120 seconds. [1232879.903607] Tainted: P&nbs........
  • Centos and obfsproxy install errors


    pip install obfsproxy /usr/lib/python2.6/site-packages/pip/_vendor/requests/packages/urllib3/util/ssl_.py:90: InsecurePlatformWarning: A true SSLContext object is not available. This prevents urllib3 from configuring SSL appropriately and may cause certain SSL connections to fail. For more information, see https://urllib3.readthedocs.org/en/latest/security.html#insecureplatformwarning. InsecurePlatformWarning You are using pip version 7.1.0, however version 8.1.1 i........
  • Apache SSL Reverse Proxy Very Slow Solution


    This is a simple fix but not a simple problem and it still doesn't make sense to me. But in a nutshell if your target proxy server works fast when accessing directly over SSL then this may be your issue. It seems SSL does not play nicely when the target proxy destination/host has a riduculously long key (such as 8192 bits long). Now this is normally not a problem, in fact the target server could be accessed with hardly any delay directly despite such a long key.........
  • Apache Vhost HowTo Serve Same Content using a different domain and IP


    There are a few ways of doing this and all basically involve using the reverse proxy or "ProxyPass" feature of Apache to accomplish it. 1.) Create a normal vhost and simply symlink the root directory of the site you want to mirror. Eg. originalsite.com and newsite.com /vhosts/originalsite.com/httpdocs You would symlink like this: ln -s /vhosts/originalsite.com/httpdocs vhosts/originalsite.com/........
  • Linux Mint/Ubuntu/Debian Dual NICs networks problem when enabling and disabling one device


    The Scenario You have dual NICs and you disable NIC1 which uses 192.168.1.1 as its gateway. With NIC2 you enable it/connect it to another network which also has the gateway 192.168.1.1 Everything will work fine at this point. When switching back to NIC1 even with NIC2 disabled and even unplugged, the OS basically can't pick up the new/updated ARP entry of the old device for 192.168.1.1 and perhaps thinks it is a security risk or spoof of some sorts and blocks i........
  • Redirect www host to non-www Linux Apache modrewrite


    The below forces all request to your domain to go to the main non-www root domain. Updated code: RewriteCond %{HTTP_HOST} !=domain.com RewriteRule ^(.*)$ https://newurl.com/subdir/$1 [R=301,L] If you don't want it to go to a subdirectory: RewriteCond %{HTTP_HOST} !=domain.com RewriteRule ^(.*)$ https://newurl.com/$1 [R=301,L] Bad code: This code is bad beca........
  • Cannot get mono to work properly on Linux Mint


    mono/wine not working in Ubuntu/Linux Mint/Debian: The assembly mscorlib.dll was not found or could not be loaded. It should have been installed in the `/usr/lib/mono/2.0/mscorlib.dll' directory. solution: sudo apt-get install mono-complete Problems: mono does not work well for even simple things like a Winrar self extracting .exe fi........
  • openvz yum problem Centos 6.5 cannot find file on mirror:


    #solution Edit /etc/yum.repos.d/openvz.repo For the first two entries comment out #mirrorlist and uncomment #baseurl and then it worked openvz yum problem Centos 6.5 cannot find file on mirror: yum update Loaded plugins: fastestmirror Determining fastest mirrors * openvz-kernel-rhel6: mirrors.ustc.edu.cn * openvz-utils: mirrors.ustc.edu.cn base ........
  • Centos yum mirror problem error "[Errno 14] PYCURL ERROR 22 - "The requested URL returned error: 404 Not Found""


    [Errno 14] PYCURL ERROR 22 - "The requested URL returned error: 404 Not Found" The above happened when for some reason all the mirrors in my cache didn't have the files (some mirrors only keep the latest version of Centos). Itried to block them all but that didn't help because it seemed the mirrors were all hardcoded no matter what I tried. Here is how to fix it and reset your mirror list in Centos cd /var/cac........
  • Linux disable firmware prevents NIC/Ethernet from working phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.


    [ 17.208336] tg3 0000:08:00.0: eth0: Link is up at 1000 Mbps, full duplex [ 17.210194] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX [ 76.000065] phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware. [ 76.002332] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 86.736004] eth0: no IPv6 routers present [ 148.960038] phy0 -> rt2x00lib_request_fi........
  • cPanel How to set SSL and Dedicated IP in cPanel


    Account Functions -> Change Site's IP Address Choose the domain and then click "Change" Choose the new IP 1.) Setup SSL Certificate in cPanel Click on "SSL/TLS Manager" under the "Security" section. 2.) Under " Private Keys (KEY)" Click "Generate, view, upload, or delete your private keys." Choose "Key Size: 4096........
  • PHP Issues with Joomla Strict Standards: Non-static method JLoader::import() should not be called statically


    This is basically caused by upgrading PHPto a new version like 5.4 when you had 5.2 before and an old version of Joomla. The only solution is to upgrade Joomla or downgrade PHP, both of which can be a pain. Strict Standards: Non-static method JLoader::import() should not be called statically in /home/userdir/public_html/libraries/joomla/import.php on line 29 Strict Standards: Non-static method JLoader::register() should not be ca........
  • libguestfs tools howto guide for managing virtual machine images


    libguestfs tools howto guide for managing virtual machine images To mount a partition #mount the kvmuser102821.img image and the /dev/sda1 partition from it to the local directory "mount" guestmount -a kvmuser102821.img -m /dev/sda1 mount To list partition info on the image: virt-df image.img Filesystem........
  • /usr/libexec/mysqld: The table 'session' is full solution


    First of all if you're getting this error it is a result of extreme database activity. If you aren't expecting it or it doesn't make sense to you 99% of the time this is a database driven script being exploited (some common examples I see often are things like phpBB being hit by dozens, hundreds or thousands of bots making constant DB write requests). The easiest way to identify this is to restart MySQL and then run the third party tool "mtop" and you'll see all........
  • The Best NoSQL Solution


    To first start off, there are many misconceptions about NoSQL and especially its strengths and weaknesses. Even the popular NoSQL solution MongoDB is fraught with issues that no one seems to be concerned about aside from a few but there are serious issues with database integrity and verified writes. MySQL was considered dangerous or incomplete at one point without having the transactional safety features of Oracle for example. However the NoSQLimplementations seem........
  • What a hdd hard drive and mdadm RAID array failure looks like in Linux


    [3805108.257042] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [3805108.257052] sd 0:0:0:0: [sda] Write Protect is off [3805108.257054] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [3805108.257066] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [3805108.257083] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [3805108.257090] sd 0:0:0:0: [sda] Write Protect is off........
  • Vbulletin howto resend confirmation e-mail


    Visit that link http://yourforums.com/forum/register.php?do=requestemail Or in AdminCPit can be done.........
  • CPanel suhosin install failed


    /scripts/phpextensionmgr install PHPSuHosin Updating md5sum list Fetching http://httpupdate.cpanel.net/cpanelsync/easy/targz.yaml (connected:0).......(request attempt 1/12)...Resolving httpupdate.cpanel.net...(resolve attempt 1/65)... Fetching http://httpupdate.cpanel.net/mirror_addr_list (connected:0).......(request attempt 1/3)......connecting to 74.50.120.123...@74.50.120.123......connected......receiving...100%......request success......Done........
  • Dell Perc 6/i cannot downgrade


    I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally. I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN --2013-08-26 12:53:39-- http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN Resolvi........
  • WHMCS CC Encryption Hash


    It is stored in the "configuration.php" file of all places which is annoying andI get questons like this at worke each day.........
  • Brand new WDD 500GB Blue 3.5 SATA Drive Dead After Shipping


    These drives seem to die very easily during shipping: sd 0:0:0:0: [sda] Unhandled error code sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK sd 0:0:0:0: [sda] CDB: Read(10): 28 00 18 8b 65 e0 00 00 08 00 end_request: I/O error, dev sda, sector 411788768 sd 0:0:0:0: [sda] Unhandled error code sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK sd 0:0:0:0: [sda] CDB: Read(10): 28 00 18 8b........
  • SSH Can't Login/Hang


    Client Log OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to 192.168.1.253 [192.168.1.253] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type 1 debug1: identity file /root/.ssh/id_d........
  • Toshiba Hard Drive Warranty RMA Serial Number Info


    Here's the link to the warranty checker and from there you can also create an RMA: https://myapps.taec.toshiba.com/myapps/admin/jsp/webrma/addRequest1NoLogin.jsp Note that the serial# shown in SMART is not complete as is the case for many other brand sof HDDs. For example a 2TB Toshiba shows the following Serial Number in SMART: Device Model:........
  • Strange SATA error code when turning on HDD/Hard drive - [1433128.139339] sd 5:0:1:0: [sde] Unhandled error code [1433128.139343] sd 5:0:1:0: [sde] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [1433128.139348] sd 5:0:1:0: [sde] CDB: Read(10):


    [1433128.139339] sd 5:0:1:0: [sde] Unhandled error code [1433128.139343] sd 5:0:1:0: [sde] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [1433128.139348] sd 5:0:1:0: [sde] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [1433128.139360] end_request: I/O error, dev sde, sector 0 [1433128.139410] sd 5:0:1:0: [sde] Unhandled error code [1433128.139414] sd 5:0:1:0: [sde] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [1433128.139420] sd 5:0:1........
  • "Cannot load certificate file keys/server.crt: error:0906D06C:PEM" OpenVPN Solution


    Cannot load certificate file keys/server.crt: error:0906D06C:PEM The .crt is blank empty because when generating it I kept hitting enter for the defaults and this caused the crt not to be signed. Certificate is to be certified until Dec 18 00:35:49 2022 GMT (3650 days) Sign the certificate? [y/n]:y 1 out of 1 certificate requests certified, commit? [y/n]y So if you get messages like these, a........
  • How To Test If Your Hard Drive Is Good/Signs of dying hard drive


    I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem: We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........
  • Apache High CPU Usage Enable Mod_Status Guide Solution - Find Cause of High CPU Usage Script/Domain


    mod_status is a great way to track down the source of high CPU usage and to find what vhost/script is the cause of it. It gives you a live view of bandwith usage, CPU usage, and memory usage broken down by domain/vhost and script/URI. Enable mod_status vi /etc/httpd/conf/httpd.conf ExtendedStatus On SetHandler server-status Order Deny,Allow Deny from all All........
  • encrypt bash scripts to hide source code


    http://www.datsi.fi.upm.es/~frosal/ SHC is a program written by the author above that does just that, it's a great little tool to have. Some have said it isn't exactly encrypting the code but just making it hard to read by obfuscating the code. There was also a good discussion about that here:........
  • Are my WDEARS20 Drives dying already?


    This happened during a RAID array check: SMART says both drives pass the test, but I'm doing a long test on them and hopefully this is not a hardware error. Apr 3 04:22:01 remote kernel: md: syncing RAID array md2 Apr 3 04:22:01 remote kernel: md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc. Apr 3 04:22:01 remote kernel: md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for reconstruction. Apr........
  • Virpus Review/Scam/Complaint


    Virpus Review/Scam/Complaint Virpus is advertised on LEB (lowendbox.com). My initial payment was refunded after days of not receiving the VPS, but two subscrption payments went through and Ionly received notification after the second one. They ignored the requests in the ticket and by e-mail for a refund and even escalated the PayPal dispute that "we're assuming this is for a service that was provided" (when they obviously know otherwise by........
  • Apache MPM worker vs prefork


    find what MPM Apache is using, it will either be using "worker" or "prefork" apachectl -l Compiled in modules: core.c prefork.c http_core.c mod_so.c In my case it is "prefork" vi /etc/httpd/conf/httpd.conf Find the section that looks like this (by default one will normally exist for prefork and for worker, but in my case I only care a........
  • Linux - mptbase/MPT Fusion LSI Logic Error mptbase: ioc0: ERROR - didn't initialize properly! (-1)


    kernel 2.6.27.54 Fusion MPT base driver 3.04.07 Copyright (c) 1999-2008 LSI Corporation Fusion MPT SPI Host driver 3.04.07 mptbase: ioc0: Initiating bringup mptbase: ioc0: WARNING - Unexpected doorbell active! mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000001! mptbase: ioc0: ERROR - Diagnostic reset FAILED! (102h) mptbase: ioc0: WARNING - NOT READY! mptbase: ioc0: ERROR - didn't initialize proper........
  • VPS Server Scam/Review/Complaint List


    These are the only two I've encountered but here is the low-end and note my story is not at all unique. In my case I was scammed out of money and did not receive any service at all from either company. Santrex Review/Scam/Complaint Santrex never provided any working server, I believe it was just a dummy management Solus server because the server said it was booted but never connected to the console. I complained to them and eventually the support adm........
  • Installing Webmin & Enabling SSL


    Webmin Setup Centos 5: wget http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html&ts=1294339690&use_mirror=surfnet [1] 24229 [2] 24230 [root@host ~]# --2011-01-06 21:48:20-- http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html Resolving downloads.sourceforge.net... 216.34.181.........
  • Kernel Error - 2.6.35.2 stuck on the following: msgmni has been set to 1466 request_module: run away loop modprobe char-major-5-1


    2.6.35.2 stuck on the following: msgmni has been set to 1466 request_module: run away loop modprobe char-major-5-1 I don't know the fix for it, but it is an old bug that has reappeared.........
  • mdadm when a RAID 1 member dies


    [27969.398749] sd 5:0:0:0: [sdb] 3907029168 512-byte hardware sectors (2000399 MB) [27969.398749] sd 5:0:0:0: [sdb] Write Protect is off [27969.398749] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [27969.398749] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [27972.117543] ata6.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 [27972.117543] ata6.00: irq_stat 0x48000000 [27972.117543] ata6.00: cmd 60/08:00:ff:7........
  • FUSE/Curlftpfs mount ftp account as drive partition in Linux


    This is a great way to use your ftp server space, for example on your web hosting account (althoughI believe many hosts don't allow storage like this), but if you have a VPS/Dedicated Server etc.., this would be perfect. Imagine how easy it is to work with an ftp account that you can just mount as a normal partition or directory in Linux, it would be great for backups etc.. Name curlftpfs - mount a ftp host as a local directory Synopsis........
  • WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED! "IT IS POSSIBLE THAT SOMEONE IS DOING SOMETHING NASTY! Someone could be eavesdropping on you right now (man-in-the-middle attack)! It is also possible that the RSA host key has just been changed. The f


    @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @ WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED! @ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ IT IS POSSIBLE THAT SOMEONE IS DOING SOMETHING NASTY! Someone could be eavesdropping on you right now (man-in-the-middle attack)! It is also possible that the RSA host key has just been changed. The fingerprint for the RSA key sent by th........
  • Seagate Drive 500GB Drive Dying


    This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device........
  • Other Security Web Sites


    Other Security Web SitesSeveral websites actively track security issues. This list provides you with the major providers of security information on the Web. Many of these organizations also provide newsletters and mailings to announce changes or security threats: Center for Education and Research in Information Assurance and Security (CERIAS) CERIAS is an industry-sponsored center at Purdue University that is focused on technology and relate........
  • pound a Linux Load Balance and Reverse Proxy


    I have played around with Pound a little bit. It is a reverse proxy and load balancer in one, and it can be used as only a reverse proxy if you like. It is very simple to configure as either, and Pound even senses if one of the systems is down and stops sending requests to the dead server. It supports SSL (but passes the request to the destination server unencrypted) and even the Apache log format. Pound is very simple, fast a........
  • Samba SMB Error - Server not using user level security and no password supplied. tree connect failed: NT_STATUS_WRONG_PASSWORD


    Server not using user level security and no password supplied. tree connect failed: NT_STATUS_WRONG_PASSWORD That happens when trying to use smbclient to connect to a share. The weird thing is that I can authnenticate just fine from Windows XP. It is partially my mistake, I forgot this share does have a password. I've tried authenticating with the correct user and also with "Guest" because this works in Windows. In Linux I ........
  • ENOM Major Outage


    At this time we can't resolve Enom's website and all DNS requests to their 4 primary name servers are failing, although the hostnames themselves still resolve: Name Server: DNS1.NAME-SERVICES.COM Name Server: DNS2.NAME-SERVICES.COM Name Server: DNS3.NAME-SERVICES.COM Name Server: DNS4.NAME-SERVICES.COM Name Server: DNS5.NAME-SERVICES.COM You would really think Enom, bein........
  • Latest Articles

  • Debian Ubuntu Mint Howto Create Bridge (br0)
  • How To Control Interface that dhcpd server listens to on Debian based Linux like Mint and Ubuntu
  • LUKS unable to type password to unlock during boot on Debian, Ubuntu and Mint
  • Debian Ubuntu and Linux Mint Broken Kernel After Date - New Extra Module Naming Convention
  • Wordpress overwrites and wipes out custom htaccess rules and changes soluton
  • Apache htaccess and mod_rewrite how to redirect and force all URLs and visitors to the SSL / HTTPS version
  • python 3 pip cannot install mysql module
  • QEMU-KVM won't boot Windows 2016 or 2019 server on an Intel Core i3
  • Virtualbox vbox not starting "No suitable module for running kernel found"
  • Bind / named not responding to queries solution
  • Linux Mint How To Set Desktop Background Image From Bash Prompt CLI
  • ImageMagick Convert PDF Not Authorized
  • ImageMagick Converted PDF to JPEG some files have a black background solution
  • Linux Mint Mate Customize the Lock screen messages and hide username and real name
  • Ubuntu/Gnome/Mint/Centos How To Take a partial screenshot
  • ssh how to verify your host key / avoid MIM attacks
  • Cisco IP Phone CP-8845 8800/8900 Series How To Reset To Factory Settings Instructions
  • ls how to list ONLY directories
  • How to encrypt your SSH private key file id_rsa
  • Linux Mint 18 Disable User Name List from showing on Login Screen