• pptp / pptpd not working in DD-WRT iptables / router


    Although it is well-known that pptp is not secure and is subject to many forms of attacks, the reality is that a lot of legacy and embedded devices use pptp. I argue that if it is being used for routing or remote access or over an already secure connection (eg. another VPN like ikev2) then this is still acceptable. Or in a LANor in a public environment where no private data is exchanged. However, if the nature of the data is extremely sensitive, you should do whatever........
  • Linux and Windows Dual Boot Issue NIC Won't work After Booting Windows


    In Windows, with some NICs, especially Intel, Windows may enable features on the card that break it in Linux. It is hard to troubleshoot as what you'll see is that the NIC is still detected in Linux, the NIC/port will be up but nothing will work (eg. DHCP requests or even static IPs won't work). You may see STP bridge traffic but that is all. In a corporate environment this can result in many calls to support and is essentially downtime and an unnecessary waste of resource........
  • Using Cisco CME Router with Asterisk as a dial-peer


    #Remember that you need a valid gateway IPunless the Asterisk server is on the same subnet and LAN Set Valid Gateway IP (if you don't have one already) ip route 0.0.0.0 0.0.0.0 GATEWAYIP Enable VOIPTrust voice service voip ip address trusted list ipv4 0.0.0.0 0.0.0.0 sip Set Credentials For Asterisk and Register To Asterisk sip-ua........
  • Cisco CME How To Configure SIP Trunk VOIP


    This is how we configure outside PSTNaccess or dialing through another SIPtrunk. Beware that this a simplistic example that neglects most security including SRTP First you'll need to be in config mode: Step - 1 Enter Voice Service VOIP security options There are more options but for now we'll just focus on security/allowing connections to and from our phones and the trunk. Router(config)#voice service voip ........
  • Cisco CME and C7200 Router Testing and Learning Environment on Ubuntu 20+ Setup Tutorial Guide


    Since newer versions of Ubuntu like 20, you will find there is no longer dynagen and that the dynamips provided is faulty and will segfault each time: Cisco Router Simulation Platform (version 0.2.14-amd64/Linux stable) Copyright (c) 2005-2011 Christophe Fillot. Build date: Apr 3 2018 12:20:29 Local UUID: 3c1c0b7f-2fab-4fda-b40b-74841d1bcfe0 Instance ID set to 1. netio_tap_create: unable to open TAP device tap1 (No such fi........
  • CDN Cloudflare how to set and preserve the real IP of the client without modifying application code on Apache


    Your frontend CDN (eg. Cloudflare or even your own load balancer/proxy) must be sending the X-Forwarded-For and you must be running Apache on the backend. This solves the problem where your logs and services will only see the proxy/CDN IP and not the real client IP. mod_rpaf will fix all of this This solution transparently sets the real IP of the client for Apache and any services that rely on........
  • hostapd example configuration for high speed AC on 5GHz using WPA2


    This example is using RTL8821AU chipset from a TP-Link T2U Plus USB adapter and other similar ones should work the same. Here's how to get this chipset RTL8821AU working in Linux. Here's how to get RTL8812 and RTL8822 working in Linux.........
  • hostapd how to enable and use WPS to connect wireless devices like printers


    Edit your /etc/hostapd/hostapd.conf file like below and restart hostapd. #WPS stuff # Enable control interface for PBC/PIN entry wpa_psk_file=/etc/hostapd/hostapd.psk ctrl_interface=/var/run/hostapd eap_server=1 wps_state=2 ap_setup_locked=1 wps_pin_requests=/var/run/hostapd.pin-req config_methods=label display push_button keypad #WPS model info stuff change to suit your needs d........
  • [error] (28)No space left on device: Cannot create SSLMutex Apache Solution Linux CentOS Ubuntu Debian Mint


    Have you got this error from Apache? [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec) [error] (28)No space left on device: Cannot create SSLMutex At first glance it appears that you may be out of disk space but the issue is ipc or interprocess communication. This will clear out the ipcs processes so things can work, this often happens during high traffic and may be a sign of DDOS. The command below will fix it, it will list al........
  • How To Stop DNSMasq from listening on all IPs/Interfaces and allow only localhost


    Some people find it less than intuitive to do on DNSMasq and by default DNSMasq is available on 0.0.0.0 which could even be your LAN or Public IP. Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp ........
  • Docker Swarm vs Kubernetes Comparison Guide


    A lot of companies are unsure which solution to choose and many may not be aware of Docker Swarm as an alternative to Kubernetes. One thing that many Sysadmins find is that Docker Swarm is simply easier, quicker to setup and maintain by far than Kubernetes.........
  • When is it time to leave your VPS/VDS Cloud Hosting Provider?


    When Is It Time to Leave Your VPS, VDS, and Dedicated Server Provider? Choosing the right hosting solution—be it Virtu........
  • 2024 Buyer's Guide: How to Choose and Buy the Best VPS/VDS for Your Needs - Tips and Strategies


    In today’s digital landscape, finding a reliable and secure Virtual Private Server (VPS) or Virtual Dedicated Server (VDS) goes beyond just comparing specs and prices. With increasing concerns over data privacy, security breaches, and government surveillance, the wisdom of choosing your VPS/VDS provider based on juri........
  • Linux how to get list of all timezones on system Ubuntu


    find /usr/share/zoneinfo/|sed s#"/usr/share/zoneinfo/"##g|grep "/"|grep -v posix|grep -v ^"Etc/"|grep -v ^right|grep -v ^"SystemV" Africa/Addis_Ababa Africa/Abidjan Africa/Blantyre Africa/Lusaka Africa/Casablanca Africa/Libreville Africa/Asmara Africa/Bujumbura Africa/Dakar Africa/Lagos Africa/Malabo Africa/Harare Africa/Kigali........
  • How To Upgrade Debian 8,9,10 to Debian 12 Bookworm


    Step 1.) Upgrade to Debian 11 first The process to go to Debian 12 is not as smooth as 11, when trying to upgrade from Debian 10. In fact, it doesn't work directly, so you'll first need to follow this guide to update to Debian 11, reboot and come back here if successful. Step 2.) Update sources.list Update your /etc/apt/sources.list like this: deb http://........
  • Linux dhcp dhclient Mint Redhat Ubuntu Debian How To Use Local Domain DNS Server Instead of ISPs


    If you are running a local DNS server like named/bind and don't want to use the ISPsupplied DNS servers that are announced via a DHCP request (using dhclient) then the solution is simple. The reason should be obvious, but normally running your own DNS server will provide a more reliable, and fast DNS response and you won't have to worry about filtering as much (unless your upstream filters or proxies outgoing DNS requests). Edit /etc/dhcp/dhclient.conf........
  • How To Setup Python3 in Ubuntu Docker Image for AI Deep Learning


    The issue is that Docker images are stripped down, so many tools and even python3 is missing, so you'll have to build or update the actual image yourself. I assume you have started an image with something like this and that you have the Nvidia Toolkit installed (assuming you are using GPUs). If you're not using nvidia just remove --runtime=nvidia --gpus all. docker run -it --runtime=nvidia --gpus all ubuntu bash These works for most images li........
  • Linux Ubuntu Mint how to check nameservers when /etc/resolv.conf disabled solution


    You'll notice that /etc/resolv.conf contains dire warners on most Linux Desktops. # This file is managed by man:systemd-resolved(8). Do not edit. # # This is a dynamic resolv.conf file for connecting local clients to the # internal DNS stub resolver of systemd-resolved. This file lists all # configured search domains. # # Run "resolvectl status" to see details about the uplink DNS servers # currently in use........
  • How to install and configure haproxy on Linux Ubuntu Debian


    haproxy is one of the best known and widely used Open Source load balancers out there and a strong competitor to nginx. haproxy is used by many large sites per Wikipedia: HAProxy is used by a number of high-profile websites including GoDaddy, GitHub,........
  • Virtualbox Best Networking Mode In Lab/Work Environment without using NAT Network or Bridged


    Virtualbox is a very powerful tool, but for some use cases it is less than optimal. Say you are in a work, lab or other environment where you are not alone on the physical network and there could be overlap of IPs, but you need all of your VMs to be contactable from your host, VMs need to communicate with each other, and VMs need internet. NAT Network will give you VM to VM communication and internet, however, it is buggy and unstable. It also doesn't allow host to VM co........
  • Linux How to Check Which NIC is Onboard eth0 or eth1 Ubuntu Centos Debian Mint


    So say you happen to have 2 NICs of the exact same chipset, they will generally show up as the same name, with possibly a different revision in lspci. Normally this is not an issue if you have a server with 4 NICs, generally the eth0 to eth3 appears from left to the right (or right to left on some vendors) so it doesn't take much figuring out. Generally if you have different chipsets for different NICs, it should be easy to know which one is eth0 or the first NIC in the OS.........
  • Generic IP Camera LAN Default IP Settings DVR


    If you are converting a generic wifi IP camera to ethernet, it may not be that simple as many are default hard coded to a static IP of 192.168.1.168 and login info admin/admin. From there you can login to the camera and assign it to DHCP by going to http://192.168.1.168 For security these cameras +DVR should be on a separate untagged VLAN or if possible a physically isolated non-internet connected switch/network. The reference below is applicable to many of the r........
  • Error opening tftp://10.0.2.2/network-confg (Permission denied) - How To Fix Cisco Router Switch Error Solution Console


    How To Fix This Cisco Switch/Router Error %Error opening tftp %Error opening tftp://10.0.2.2/network-confg (Permission denied) %Error opening tftp://10.0.2.2/cisconet.cfg (Permission denied) %Error opening tftp://10.0.2.2/router-confg (Permission denied) %Error opening tftp://10.0.2.2/ciscortr.cfg (Permission denied) %Error opening tftp://10.0.2.2/network-confg (Perm........
  • Loaded: masked (Reason: Unit hostapd.service is masked.) Solution in Linux Debian Mint Ubuntu


    If you are getting this error from systemctl "Loaded: masked (Reason: Unit hostapd.service is masked.)" we need to unmask the service. Solution systemctl unmask hostapd Removed /etc/systemd/system/hostapd.service. It's fixed root@routerOS:/var/log# systemctl start hostapd root@routerOS:/var/log# systemctl status hostapd ● hostapd.service - Access point and authentication server for Wi-Fi and Ethern........
  • i915 nouveau Nvidia GPU not starting lightdm Xorg failing solution for Could not determine valid watermarks for inherited state


    It may appear to be an Xorg or lightdm/gdm/mdm error but in reality for many users with this issue, it's a driver conflict and issue. I had a system that had two GPUs, an Intel and Nvidia GPU. The only thing that got it working was to remove the nouveau driver and blacklist it so it never came back, then the Intel GPU works fine without these issues. Solution sudo rmmod nouveau add nouveau/other driver to blacklist edit th........
  • Libreoffice Calc Opens CSV Spreadsheet File as Asian Language/Chinese Characters Solution Fix


    Usually LIbreoffice gets it right, but if it opens a normal English CSV as UTF-16 by default and shows Asian languages, you'll have ot manually open to fix it (don't double click the file from the File Manager). Solution - Manually Open the File After Opening LibreOffice Calc You'll see it is defaulting to UTF-16 which breaks everything. ........
  • How To Tell Which Repository a Package Comes From Debian Mint Ubuntu


    Just use apt-cache policy to find the repo of a package: apt-cache policy lxd lxd: Installed: 3.0.3-0ubuntu1~18.04.2 Candidate: 3.0.3-0ubuntu1~18.04.2 Version table: *** 3.0.3-0ubuntu1~18.04.2 500 500 http://archive.ubuntu.com/ubuntu bionic-updates/main amd64 Packages &nb........
  • How To Do Linux Network Bonding Teaming in Mint Debian Ubuntu


    Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........
  • Docker Tutorial HowTo Install Docker, Use and Create Docker Container Images Clustering Swarm Mode Monitoring Service Hosting Provider


    The Best Docker Tutorial for Beginners We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........
  • How To Create OpenVPN Server for Secure Remote Corporate Access in Linux Debian/Mint/Ubuntu with client public key authentication


    Why choose OpenVPN instead of a firewall appliance? OpenVPN can be a reliable and easy replacement for traditional hardware or just be an additional tool that your company uses so that the firewall can focus on its job rather than acting as a VPNappliance at the same time. When comparing OpenVPN with traditional firewal........
  • HongKong VPS Server, Cloud, Dedicated Server, Co-Location, Datacenter The Best Guide on Hong Kong, China Internet IT/Computing


    In our 2024 VPS Server/Cloud Buyer's Guide, we place the location of your VPS/hosting/server as one of the priorities that is often overlooked. 2024 Update - Datacent........
  • Ansible Tutorial - Playbook How To Install From Scratch and Deploy LAMP + Wordpress on Remote Server


    1. Let's work from an environment where we can install Ansible on. If you are using an older version of Linux based on Mint 18 or Ubuntu 16, you may want to get the PPA and get the latest version of Ansible that way: sudo apt install gpg sudo add-apt-repository ppa:ansible/ansible sudo apt update........
  • Proxmox How To Enable Ceph Distributed Storage Cluster with OSD and Pools


    How To Install Ceph If you stopped an install of Ceph midway you will need to manually restart it with "pveceph install" Remember that your VM needs to have working internet (gateway) and DNS in order to connect to the apt repo to download all of the packages that Ceph requires. Remember to repeat these steps for each node that you want Ceph on. ........
  • Virtualbox VBOX Howto Port Forward To Guests


    NAT Network, the VMs can communicate but your host cannot access them by default. NAT VMs have internet but cannot communicate with each other. Bridged is simple and allows full LAN access as if you had a physical machine plugged in but is often bad for testing, work or corporate environments and is not very portable when it comes to moving your VMs to other locations and networks. Here is how you can use NAT Ne........
  • SSH cannot connect to old servers/devices/switches/routers/Cisco/Juniper Unable to negotiate with 192.168.20.2 port 22: no matching key exchange method found. Their offer: diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hell


    A lot of older devices either support telnet or very old SSH keyx algorithms which are insecure and disabled by all newer/modern SSH clients for security reasons. However, sometimes you may be on a LAN via VPNor some other secured network or for whatever reason, absolutely, need to connect to this device and sometimes old/embedded devices may not be possible to update to a newer SSH server. If you run into this you may be using a modern/newer SSH client and get thi........
  • Juniper JunOS Command Overview and Howtos Switch, Router, Firewall Tutorial Guide


    Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........
  • How To Get Started on Ubuntu with gpt-2 OpenAI Text Prediction


    apt install software-properties-common add-apt-repository ppa:deadsnakes/ppa apt update apt install python3-pip apt install python3.7 curl gnupg python3.7-dev git ln -s /usr/bin/python3.7 /usr/bin/python3 pip3 install numpy keras_preprocessing curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add - echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........
  • Debian and Netplan


    Create your netplan file vi /etc/netplan/01-netcfg.yaml network: version: 2 renderer: networkd ethernets: ens3: dhcp4: no ........
  • how to use ifplugd in Linux to execute a command or script when a NIC cable is unplugged or plugged in


    It is fairly simple to use once you know how to use it. However, the tricky thing is that by default it doesn't seem to be active or listen on any interface on manually specified. How To Install ifplugd First we install ifplugd sudo apt install ifplugd Let's enable it on our desired device(s) vi /etc/default/ifplugd set this line as so:........
  • mpv / mplayer with Radeon / AMD GPU Video Card Driver enable VDPAU GPU Accelerated Video Decoding


    The easiest way to know if your videos are playing with GPU acceleration are to watch the process of xplayer, mpv or whatever you are playing. The CPU usage should be no more than 10% for that process/program if it is using acceleration. Let's manually play with vdpau to make sure it works before we make it permanent: First make sure you have libvdpau installed: sudo apt install vdpau-driver-all If yo........
  • Linux 3D Performance benchmarks with glxgears 59-60fps solution


    You need to disable vsync like this when running glxgears: vblank_mode=0 glxgears For Nvidia drivers do this: __GL_SYNC_TO_VBLANK=0 glxgears Notice the higher than 59-60 fps results with vblank_mode=0: ATTENTION: default value of option vblank_mode overridden by environment. 7919 frames in 5.0 seconds = 1583.704 FPS 8187 frames in 5.0 seconds = 1637.266 FPS........
  • Apache htaccess and mod_rewrite how to redirect and force all URLs and visitors to the SSL / HTTPS version


    It is really simple using .htaccess with mod_rewrite. Here is all you need: RewriteCond %{SERVER_PORT} 80 RewriteRule ^(.*)$ https://site.com/$1 [R=301,L] Another more graceful way is to use the %{SERVER_NAME}variable to make it dynamic. Just be careful that the server name will always match what you expect. (eg. if you are doing load balancing or clustering what if the server name may be somethi........
  • Bind / named not responding to queries solution


    By default bind will not respond to outside queries for security reasons. In most distributions you will find the default in /etc/named.conf looks like this at the top under options: listen-on port 53 { 127.0.0.1; }; listen-on-v6 port 53 { ::1; }; directory "/var/named";........
  • Cisco IP Phone How To Reset To Factory Settings Instructions CP 9971, 8800, 8900, 8845, 8851, 8841, 8831, 7961, 7960, 7945, 7942, 7941, 7940.


    This would be crucial especially if the phone is hardened, not being able to reset or change settings could prevent a phone registering in a new environment or even when migrating from office to office. This applies even if you are trying to migrate the phone to another platform such as Asterisk/FreePBX etc... This guide applies to nearly all of the Cisco IP phones that you would use in CME or CUCM from several years ago including models: 9900, 9971, 8800, 8900, 8845, 8851, 8841........
  • ssh reverse proxy to enable remote access behind a LAN and firewall


    So say you are behind a typical NAT/LAN setup whether at home, work or while travelling. What if you have a computer or server that you need to connect to from the outside? Yes you could use a VPN but a quick and dirty, temporary and secure way is to use SSH's Reverse Tunneling Proxy feature. Requirements On the remote ssh server host you need the GatewayPorts option enabled in sshd_config (be........
  • Cisco Router Setup Guide and Tutorial Howto With Commands and Examples


    In most of the Cisco router IOS I find the ports like ge0/0 ge0/1 and ge0/2 or whatever your ports are down. They will not even give you a link light. So one of the first tasks should be getting the port you are working with up. In my case the first goal is often connectivity with the LAN and WAN. LAN = your local area network (eg. in the office/home ) WAN= your ISP/public internet (eg. fiber/cable/dsl/ethernet).........
  • Cisco DHCP Snooping Relay Setup Information


    Switch#show ip dhcp snooping Switch DHCP snooping is disabled DHCP snooping is configured on following VLANs: 1 Insertion of option 82 is enabled circuit-id format: vlan-mod-port remote-id format: MAC Option 82 on untrusted port is not allowed Verification of hwaddr field is enabled Interface&nb........
  • Cisco Switch Setup Guide Command List


    Enter configuration console: enable configure terminal This is important because if your console doesn't look like below none of the commands will work! Switch(config)# Save and Apply Settings wr Show Switch Configuration: show run Show Port List/Sta........
  • Cisco Switch Reset To Factory Defaults


    This works on the 2000 and 3000 series generally. *The easy way is to just hold the mode button for 10+ seconds. The full/proper way is below: 1.) Either power on the unit and hold the "mode" button or hold the "mode" button until you see the below: 00:04:08: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram 00:04:08: %EXPRESS_SETUP-6-CONFIG_IS_RESET: The configur........
  • Linux wlan0 check all wireless clients


    iw dev wlan0 station dump This is very useful because it is helpful if you are running something like hostapd and need to see the signal strength and negotiated connection speed. Station ff:ff:ff:ff:ff:ff (on wlan0) inactive time: 16309 ms rx bytes: 25451 rx packets: 325 tx bytes: 44381 tx packets: 159 tx retries: 0 tx failed: 0 signal: -72 [-72] dBm signal avg: -72 [-72] dBm........
  • iSCSI on Centos 7 Configuration and Setup Guide for Initiator and Target


    initiator = client target = server These are the first concepts you should understand which is that in iscsi essentially the "initiator" is the client and the "target" is the server. iSCSI is derived from the old fashioned SCSI that us oldtimers grew to love. The "i" stands for Internet and the SCSI stands for "Small Computers Systems Interface" (SCSI). iSCSI Target (Server)Setup targetcli is the pac........
  • How Does Cisco CUCM (Cisco Unified Communication Manager) Work?


    Cisco's CUCM (Cisco Unified Communication Manager) is a system that combines voice, video, data and mobile products into a single unified management suite. At its core, the CUCMis like a "Super PBX" that controls the flow of all communications through an organization even single or multiple site deployments. Cisco's CUCMmakes communication more effective and simple through centralized management and unification of communications resources.........
  • bash script how to to check LAN computers for open ports


    In this case it just searches for port 80 it is fairly handy if you have some sort of appliance or something else you aren't sure of the IPof Of course change the port 80 port to whatever port(s) you want. for ip in `arp -n|arp -n|tail -n +2|head -n -1 |grep -v incomplete|awk '{print $1}'`; do echo "checking $ip:80" nc -w 1 -z $ip 80 if [ "$?" == 0 ]; then echo "**Port 8........
  • Cannot install moodle


    After starting the install it stalls here: admin/index.php?cache=0&agreelicense=1&confirmrelease=1&lang=en If you manually refresh you get a Plugins check screen: Installation System Moodle second step fails just blank screen: https://domain.la/user/editadvanced.php?id=2 Solution: give up and choose something else it shouldn't be thi........
  • Debian/Ubuntu/Mint Linux How To Set VLAN in /etc/network/interfaces


    You can find many ways to specify the VLANin your network configuration but Ifind this is the simplest and quickest. In this case we are talking about a bridged adapter "vmbr0" but it works even if you just had a normal non-bridged interface. The key here is that in vmbr0 you'll notice there is no IP address. We just specify "manual". Below it is a similar stanza for "vmbr0.58" in this case 58 represents the VLAN (change........
  • VMWare Vsphere VCSA Graphical Install Creates json


    yes it does create its own json ============================================ cat /tmp/vcsaUiInstaller/ovftool-20180809-175238948-20180809-175603497.log |grep -i json 2018-08-09T17:56:04.238-07:00 verbose OVFTool[30966] [Originator@6876 sub=Default] Manifest file entry: SHA1(VMware-vCenter-Server-Appliance-6.7.0.12000-8832884_OVF10-file1.json) = 1deb658c724767697587d5909c4051c01813e6a1 --> ........
  • Linux Centos 7 HowTo Install Yarn


    https://yarnpkg.com/lang/en/docs/install/#centos-stable curl --silent --location https://dl.yarnpkg.com/rpm/yarn.repo | tee /etc/yum.repos.d/yarn.repo If you need node.js: curl --silent --location https://rpm.nodesource.com/setup_6.x | bash - yum install nodejs yarn........
  • Cannot create gradle for conversations


    The main issue is it looks like Java is not configured to accept the invalid ssl cert that is coming from the download location. Exception in thread "main" java.lang.RuntimeException: javax.net.ssl.SSLException: java.security.ProviderException: java.security.InvalidKeyException: EC parameters error export ANDROID_HOME=/home/user/Downloads/tools/ Conversations-master$ ./gradlew Downloading https://services.gradle.org/distributions/grad........
  • named [FAILED] - zone 1.168.192.in-addr.arpa/IN: not loaded due to errors. - bind error solution


    Centos when copying old files and restarting it seems load everything fine and then says [FAILED] with no log or other message. service restart named named [FAILED] Check more thoroughly you may have missed the error if you have lots of zones! service named restart|grep error zone 1.168.192.in-addr.arpa/IN: not loaded due to errors. zone 2.168.192.in-addr.arpa/IN: no........
  • OpenVPN cannot ping remote IP routing loop issue after connecting


    Sometimes if you have a very basic configuration OpenVPN on the client side for some reason sends all traffic to the OpenVPN server IP through the tun0 which is of course impossible and creates a block or routing loop. This is because you need to use your normal ISP/LANgateway to hit the OpenVPN server if it is remote/offsite as is usually the case. So if you are connected to the OpenVPN through say a tun0 device and your routing is set to connect to the OpenVPN&nbs........
  • Apache htaccess Custom ErrorDocument not working properly for root home page 403 Error Issue and Solution


    So I have a domain "testdomain.com". Inside test domain.com's root is the following .htaccess: Options +FollowSymLinks -Indexes ErrorDocument 403 /launch/index.html Order Deny,Allow Deny From All Allow From 192.168.1.2 When you visit anything other than root things work fine. Eg. if you visit http://testdomain.com/somedirfile.html It will show the right error in /launch/........
  • samba how to listen on specific IP only


    This is useful for security purposes especially on a server which may have a public IP assigned to it but has a second NIC for the LAN. Here is how you edit smb.conf: [global] interfaces = 192.168.1.50 bind interfaces only = yes As you can see above it will only listen on 192.168.1.50 and remind to keep the "bind interfaces only"option.........
  • How To Secure Samba NMBD/SMBD to bind to a specific IP address


    By default Samba SMB/NMB listen on ANY and ALLIPs on your system by binding to 0.0.0.0. Obviously this is a huge security risk if you have a public facing server with both internal and external access. Usually when a system administrator sets up a samba server their intention is just to share with a LAN. To do this you need to the following options under the [global] section in smb.conf bind interfaces only = yes interfaces = 192........
  • kdenlive titles/text renders as white screen when using .sh script


    When using the .sh script the rendering doesn't work after an upgrade of related packages to kdenlive. kdenlive (kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1)) with affine or composite transitions was fine but is now broken during the time of transition it is just a white screen. The previous version was fine: kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1 But now I can't find it or install it:........
  • ffmpeg Unable to Use Hardware Encoding with Nvidia 3.40 Driver and GT210 card


    I believe from what I've read that this card's driver doesn't support the features after trying all known troubleshooting methods. ffmpeg -i uservideoRendered.mp4 -filter:v hwupload_cuda,scale_npp=w=1920:h=1080:format=nv12:interp_algo=lanczos,hwdownload -c:v hevc_nvenc -profile main -preset slow -rc vbr_hq -c:a copy uservideoRendered.mp4-test ffmpeg -i uservideoRendered.mp4 -filter:v hwupload_cuda,scale_npp=w=1920:h=1080:format=nv12:interp_algo=lanczos,hwdownload........
  • ffmpeg Linux Mint download, compile and install howto


    #if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2 tar -jxvf ffmpeg-3.3.2.tar.bz2 cd ffmpeg-3.3.2/ ./configure --disable-yasm install prefix /usr/local source path ........
  • Centos 7 Cudaminer Nvidia setup guide


    I am using a GTX 1060 but replace the download for the driver with the correct/current version for your particular card by visiting: http://www.nvidia.com/Download/index.aspx?lang=en-us yum install automake curl openssl-devel libcurl-devel gcc gcc-c++ yum -y install kernel-devel-`uname -r` yum -y install unzip #the........
  • DRBD Split-brain solution


    Uh oh [17925926.174277] block drbd0: Handshake successful: Agreed network protocol version 96 [17925926.174325] block drbd0: conn( WFConnection -> WFReportParams ) [17925926.174342] block drbd0: Starting asender thread (from drbd0_receiver [1682]) [17925926.174432] block drbd0: data-integrity-alg: [17925926.174581] block drbd0: drbd_sync_handshake: [17925926.174586] block drbd0: self 2AAE66AF9252D6DB:2815BF........
  • PayPal Subscription Howto Creation Automatic Payments Manual


    An easy way to pay companies and friends/family since PayPal does not have an option when sending money to make it a subscription: "business" = The e-mail or PayPal ID of the person/organization to pay to. a3 The recurring amount "eg. 115" will be 115 USD p3 The time period (eg. 2) t3 Unit of time period m=monthly,w=weekly,y=yearly item_name = "the note/product service reason you are paying ha........
  • mcp55 NIC not working at boot on Centos 6.6-6.8


    forcedeth 0000:00:08.0: irq 25 for MSI/MSI-X forcedeth 0000:00:08.0: eth0: MSI enabled forcedeth 0000:00:08.0: eth0: no link during initialization ADDRCONF(NETDEV_UP): eth0: link is not ready forcedeth 0000:00:08.0: eth0: link up ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Dec 1 18:21:32 box15 kernel: forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64. Dec 1 18:21:32 box15 kernel........
  • DRBD Slow Performance - 99.99 % [jbd2/drbd0-8] highiowait solution


    Tired of checking iotop and seeing that your drbd partition is using 99.99% of io all the time and finding your drbd device performs slow in general? This is especially an issue in versions of DRBD in the 8.3 tree in particular one documented case is on "8.3.13" but it likely applies to other devices. The symptoms are that resyncing is fine and normal but any reasonable amount of activity is very slow and lagged and creates a high server load and con........
  • Nvidia Linux Card not working due to LSI 9200/SAS2008 IRQ conflict


    At first my BIOS said the card may not work right because there is no more option ROM space. I disabled the Option ROM for both LSI 1068 and 2008 chipsets, Network Boot ROM and most other PCI slots, Serial Port, etc... and the message went away but the card still does not work properly. But it still cannot initialize the card properly(does not work): [ 33.943272] NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:........
  • Linksys / Cisco / Grandstream / Polycom PAP2T No delay in dialing recommended fast dial plan


    I modified the default to the following for faster local dialing for North American area codes: (*xx|[3469]11|0|00 [2-9]xxxxxxS0|[2-9]xxxxxxxxxS0|1xxx[2-9]xxxxxxS0|xxxxxxxxxxxx.) This is what I added to the above: "[2-9]xxxxxxxxxS0" so any 9 digit number is dialed instantly xxx-xxx-xxxx (the S0 at the end makes it dial right away). This makes dialing much quicker and is recommended. *No........
  • Linux Debian/Ubuntu/Centos How To Force Internet Traffic Through PPTP L2TP OpenVPN Account Only


    The following assumes the computer is local/physical to you and/or it always has a LANIP so it can be accessed on site without having a default gateway. The key to this is not to set a default gateway for your computer or you can set a script on boot or other time to delete the gateway (where eth0 is the NIC you are using): route del default eth0 50.80.20.2 is the VPN server you connect to 192.168.1.1 is your........
  • Avocent 8020 KVM Java Icedtea Viewer


    This command in Debian/Ubuntu/Mint will get everything need installed for most Java based KVM viewers: sudo apt install icedtea-netx The following additional packages will be installed: ca-certificates-java icedtea-netx-common openjdk-8-jre openjdk-8-jre-headless It seems every other updated version of Java or Icedtea breaks things and I will save the frustration of Java for another post.........
  • Centos 6 how to guide convert LVM non-RAID into mdadm 1/10 RAID array live without reinstalling


    Here is the scenario you or a client have a remote machine that was installed as a standard/default minimal Centos 6.x machine on a single disk with LVM for whatever reason. Often many people do not know how to install it to a RAID array so it is common to have this problem and why reinstall if you don't need to? In some cases on a remote system you can't easily reinstall without physical or KVM access. So in this case you add a second physical or disk or already ha........
  • openvz yum problem Centos 6.5 cannot find file on mirror:


    #solution Edit /etc/yum.repos.d/openvz.repo For the first two entries comment out #mirrorlist and uncomment #baseurl and then it worked openvz yum problem Centos 6.5 cannot find file on mirror: yum update Loaded plugins: fastestmirror Determining fastest mirrors * openvz-kernel-rhel6: mirrors.ustc.edu.cn * openvz-utils: mirrors.ustc.edu.cn base ........
  • Dell CS24-NV7 lspci dmidecode info


    0000:00:00.0 RAM memory: NVIDIA Corporation MCP55 Memory Controller (rev a2) 0000:00:01.0 ISA bridge: NVIDIA Corporation MCP55 LPC Bridge (rev a3) 0000:00:01.1 SMBus: NVIDIA Corporation MCP55 SMBus (rev a3) 0000:00:02.0 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a1) 0000:00:02.1 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a2) 0000:00:05.0 IDE interface: NVIDIA Corporation MCP55 SATA Controller (rev a3) 0000:00:05.1 I........
  • Dell CS24,FS12 NV5 and NV7 1U Server Information & Parts


    Motherboard: Gigabyte GA-3CESL: http://b2b.gigabyte.com/products/product-page.aspx?pid=2658#dl Dell Part Numbers for the motherboard: R1232 R1232L R2232S SERVER MOTHERBOARD GENUINE 408P9 CN-0408P9 GA-3CESL Manual Download here RAMSlots: 16 (8 controlled by each CPU) RAMType: DDR2 ECC 5300P........
  • Dell CS10-F1D Server Info lspci Linux specs


    0000:00:00.0 Host bridge: Intel Corporation 5000P Chipset Memory Controller Hub (rev b1) 0000:00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 (rev b1) 0000:00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 (rev b1) 0000:00:04.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 (rev b1) 0000:00:05.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4........
  • CPanel Link to all of the command line options


    CPanel says you can access 98% of the functions through CLI which experienced Unix/Linux admins prefer for simplicity and for scripting.  I've never found CPanel easy to use from the admin panel, it seems everything is hard to find and a simple task becomes a series of hunts. So for people like me here's the list: http://cpanel.net/system-administrators/command-line-scrip........
  • drbd 8.3 hard drive failure recovery example


    drbd 8.3 hard drive failure recovery drbdadm attach r0 DRBD module version: 8.3.10 userland version: 8.3.8 you should upgrade your drbd tools! 0: Failure: (119) No valid meta-data signature found. ==> Use 'drbdadm create-md res' to initialize meta-data area. ........
  • drbd won't create device if previous partition is on it Command 'drbdmeta 0 v08 /dev/md160 internal create-md' terminated with exit code 40


    This is what fixed it: [root@box13 ~]# dd if=/dev/zero of=/dev/md160 bs=512 count=500 Basically you need to wipe out more than just the 512 byte partition table so 512 bytes * 500 is more than enough to make DRBD happy and think the partition is now empty. The reason this happens is because it gets confused when there is a previous partition with data on the device you are using. root@box13 ~]# d........
  • Dell CS24-NV7 Howto Enable LAN/NICs and PXEBoot in the BIOS


    Dell CS24-NV7 Unusually the Virtualization was enabled when I got this server but all the NICs were diabled in the BIOS including PXE boot! Advanced -> Advanced Chipset Control PCI Slot 1 Option ROM: Enabled Onboard LAN1 Control: Enabled LAN1 Option ROM Scan: Enabled (you need it for PXE boot) Onboard LAN2 Control: Enabled LAN2 Option ROM Scan: Enabled *you will need to reboot and........
  • Dell FS12-NV7 2U Server Information and Guide


    I've got one of these for testing projects from work at home and got more than I bargained for with the time I've spent on it due to the storage handing/Perc 6/i cards. My particular model came with the following: 2U Rack Mount Server with Rails 2xOpteron 2373 EE (Quad Core, there is a 6-core version that can be found at times) 16GB RAM 2 x 250GB Seagate SATA 2 x Dell Perc 6/i (horrible and a nightmare to work........
  • Dell Perc 6/i SATA benchmarks without battery


    The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results. This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane. Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: N/A De........
  • LSI MegaRAID Adventures, Guide and HowTo


    LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
  • pxe-32 tftp open timeout


    pxe-32 tftp open timeout The solution was to enable tftp in xinetd with "chkconfig tftp on". See the troubleshooting below: chkconfig --list NetworkManager 0:off 1:off 2:off 3:off 4:off 5:off 6:off acpid 0:off&n........
  • Bash weird variable whitespace missing when echoing printing


    Bash weird variable whitespace missing var=`cat tlds.csv|grep .ca,` # echo "var=:$var:" :ar=:.ca,Canada Why is the v missing in the last line? It should be :var=:.ca,Canada instead of :ar=:.ca,Canada I noticed a problem with the file with doing a "cat -v" on it. Here's the issue, the file contains carat M ^M: .vg,British Virgin Island........
  • charat in PHP convert non-English characters into code


    This is basically URL decoding to the decimal code but nothing in PHPworks how you'd expect it. Here are online tools to verify and check your work, it's important when querying databases with non-English characters: http://yehg.net/encoding/index.php# http://meyerweb.com/eric/tools/dencoder/ http://www.codetable.net/decimal/65398 Japanese: http://symbolcodes.tlt.psu.edu/bylanguage/japanesechartkatakana.html Charat code for PHP:........
  • Asterisk how to reload extensions from the CLI


    dialplan reload It's really that simple, though some say "extensions reload" but it doesn't work for me, perhaps it depends on the version of Asterisk.........
  • openoffice calc printing extra blank pages


    Make sure that the Page mode is set to landscape and that the columns fall within the margins/boundaries, otherwise this is why there will be blank pages (Print Preview will show you this too).........
  • openoffice calc landscape printing problem


    openoffice calc landscape printing problem OpenOffice.org 3.2.1 OOO320m19 (Build:9505) ooo-build 3.2.1.4, Ubuntu package 1:3.2.1-7ubuntu1. It's not extending the printing and margins all the way to the edge even when setting the Page and print settings to Landscape Solution (incorrect margins set under Page): *Check the margins, my right margin was like 14cm!........
  • Country List Names in HTML Select From


    This is useful for developing a lot of applications, I'm putting it here to keep it handy for myself and hopefully others: Choose CountryCanadaJapanUnited StatesUnited KingdomAfghanistan........
  • SSH Can't Login/Hang


    Client Log OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to 192.168.1.253 [192.168.1.253] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type 1 debug1: identity file /root/.ssh/id_d........
  • Startech SV1107IPEXT KVM/IP Review


    Let's keep this simple, it's horrible, not only is the picture quality horrible (it's not a big deal) but the keyboard input is an issue. You have to type slowly, lightly and carefully otherwise 1-keystroke could end up being dozens of keystrokes. It's also a confusing unit for many datacenter techs, I've seen these units hooked up wrong and the instructions themselves aren't clear. I had to resort to shipping one to my office and take my phone pictures of the setup for th........
  • Lantronix KVM/IP Keyboard/Mouse not working in BIOS before booting the OS


    I've run into two issues with Lantronix based KVMs on various servers and here's how I solved them (with that said I like these units as they are Java based and OS independent and work very well, unike some other models like Startech). 1.) If you are connected by USB only and you're sure USB support from the BIOS is enabled, you just need to click the following in Lantronix Interfaces -> Keyboard/Mouse Check "Force USB Full Speed Mode", this fixed the issu........
  • Ubuntu 10.04 Flash Videos have tearing/lines Solution


    This is what I call a ridiculous bug in compiz that causes it. The solution/To fix it just install "compizconfig-settings-manager" Open it up and Navigate to General Options -> Display Settings Set the "Refresh Rate" to the current refresh rate of your monitor. For ATI cards with slow window dragging/response supposedly disabling "Sync to VBlank" fixes that but otherwise leave it as is.........
  • How to recover from dead DRBD partition/hard drive in two simple commands


    This assumes that you've at least created the correct partition for your DRBD already. Notice that I am "diskless", that's because either your DRBD partition doesn't exist/has been renamed (eg. sdb becomes sda when sdb dies and you reboot) or because that drive is really actually dead/gone. *If you need to permanently change the partition/device for your resource be sure to edit /etc/drbd.conf on both hosts and reload the config. (replace r0 with........
  • MySQL Replication/Dual-Master vs Clustering


    Many people aren't aware but recently Dual-Master Replication setups have become increasingly popular. That's because you get similar features and benefits of having a full-blown cluster (difficult to setup and maintain and requires I believe 3 servers just as controllers). With a dual-master you just have a different off-set for the keys and you should be good, but of course there is the chance that at some point replication will halt because of an unexpected or unforseen error........
  • VBulletin How To Change Welcome E-mail


    Login as Admin Languages & Phrases -> Search in Phrases Choose "Phrase Variable Name Only" Search for: welcomemail Edit the "Translation" box with what you'd like in it.........
  • nginx - the ultimate load balancer


    You can find it for free at http://nginx.org/ I find nginx is simpler to setup than pound (it's not hard but I found it unintuitive and annoying), it seemed to make some basic setups overly complicated with the config file syntax. nginx on the other hand is perfectly suited in everyway, it is even simpler to setup and seems to be the most stable and most efficient any load balancer. I would go as far as to say that a good nginx setup is more relia........
  • Picking an FTPD (vsftpd) Server in Linux Centos/Debian


    I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find. yum search ftp Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * rpmforge: ftp-stud.fht-esslingen.de * base: mirrors.netdna.com * updates: updates.interworx.info * addons: yum.singlehop.com * extras: mirrors.netdna.com rpmforge........
  • Compaq V2405CA Laptop - Unixbench Performance Test


    Here are the results, it is Sempron 3000+ AMD Mobile, 500Gig HDD, 512MB RAM with shared ATI Radeon graphics. # # # # # # # ##### ###### # # #### # # # # ## # # # #&nb........
  • PHP cannot access /usr/bin/openssl


    PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist: [code:1:1fd0f3abbe] if (!file_exists($OPENSSL)) { //echo "ERROR: OPENSSL $OPENSSL not foundn"; }[/code:1:1fd0f3abbe] I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........
  • Load Balancing Tutorial


    Load Balancing Tutorialhttp://redundancy.redundancy.org/fbsd_lb.html........
  • Basic Port Listing


    Basic Port ListingHopefully someone finds this useful or at least interesting. http://www.sans.org/top20/#u9 Name Port Protocol Description Small services ........
  • Load Balancing/Clustering


    Load Balancing/ClusteringAn interesting article that discusses the pros, cons and viability of load balancing/clustering http://www.wwwcoder.com/main/parentid/493/site/4189/68/default.aspx ZoneEdit seems to offer an interesting Fail Over Service as well: http://www.zoneedit.com/doc/faq.html#fo........
  • pound a Linux Load Balance and Reverse Proxy


    I have played around with Pound a little bit. It is a reverse proxy and load balancer in one, and it can be used as only a reverse proxy if you like. It is very simple to configure as either, and Pound even senses if one of the systems is down and stops sending requests to the dead server. It supports SSL (but passes the request to the destination server unencrypted) and even the Apache log format. Pound is very simple, fast a........
  • GRUB "Error 2: Bad file or directory type" 0.97 won


    You can see the problem below, GRUB recognizes my hard drive and sees the partitions but cannot access them. This is from the GRUB boot disc I'm using. What happened is that I had some power issues causing this system's power to be interrupted several times and basically an on/off on/off situation. The system won't boot, I just get a flashing cursor and no message or error from GRUB. Obviously the problem is that my MBR seems corrupt or some other issue. My........
  • Linux/Unix Open SSH Login Without Password Key Exchange including Debian, Redhat, Fedora, Ubuntu, BSD etc..


    In those 4 simple commands you can setup mutual key exchange between two sshservers by using a single login shell session and single window. *Just change the IP address examples of (10.10.0.2) to the target of your mutual key exchange. It doesn't matter if the server is on a LANor WAN(well unless the server is behind a firewall and you cannot SSHinto it).........
  • Timezone Change/Updated for Linux/Unix Debian/Fedora/Ubuntu/Centos Change Update Time zone


    In Newer Linux Distros This Way Is Easiest and works on newer versions like Ubuntu, Mint, Fedora, Centos, Debian etc. #if you are missing timedatectl this in newer distros like Ubuntu/Mint/Debian and are using a container like Docker then do "apt install systemd" timedatectl set-timezone America/Vancouver Replace the America/Vancouver with the correct timezone. To see the list you can just type "timedatectl set........
  • Samba SMB Error - Server not using user level security and no password supplied. tree connect failed: NT_STATUS_WRONG_PASSWORD


    Server not using user level security and no password supplied. tree connect failed: NT_STATUS_WRONG_PASSWORD That happens when trying to use smbclient to connect to a share. The weird thing is that I can authnenticate just fine from Windows XP. It is partially my mistake, I forgot this share does have a password. I've tried authenticating with the correct user and also with "Guest" because this works in Windows. In Linux I ........
  • Rackable Systems and their Microslice Clustered 1U Servers


    Ithink there has been a lot of negative press towards Rackable Systems. We will give their new solution credit that it is marketed very well, and comes prepackaged and ready to go. But let's cut through the hype of both sides, the people who love this concept and the people who hate it. What Rackable Systems have done is a first, to minimize space, power and costs into small servers. This is great, and many companies have already built their own servers based........
  • BASH script error "((: 08: value too great for base (error token is "08")"


    ((: 08: value too great for base (error token is "08") Here is the code that caused it for ((track=1;track ........
  • ENOM Major Outage


    At this time we can't resolve Enom's website and all DNS requests to their 4 primary name servers are failing, although the hostnames themselves still resolve: Name Server: DNS1.NAME-SERVICES.COM Name Server: DNS2.NAME-SERVICES.COM Name Server: DNS3.NAME-SERVICES.COM Name Server: DNS4.NAME-SERVICES.COM Name Server: DNS5.NAME-SERVICES.COM You would really think Enom, bein........
  • Comments About Networking Technology


    We've noticed in many ways that traditional networking even in WANs and LANs has changed very little. Years ago most networks were running on 100mbit and today most still are. Even the average internet connection is largely unchanged from several years ago with some minor exceptions from Europe and Asia.........
  • Latest Articles

  • FreePBX 17 How To Add a Trunk
  • Docker Container Onboot Policy - How to make sure a container is always running
  • FreePBX 17 How To Add Phones / Extensions and Register
  • Warning: The driver descriptor says the physical block size is 2048 bytes, but Linux says it is 512 bytes. solution
  • Cisco How To Use a Third Party SIP Phone (eg. Avaya, 3CX)
  • Cisco Unified Communication Manager (CUCM) - How To Add Phones
  • pptp / pptpd not working in DD-WRT iptables / router
  • systemd-journald high memory usage solution
  • How to Install FreePBX 17 in Linux Debian Ubuntu Mint Guide
  • How To Install Cisco's CUCM (Cisco Unified Communication Manager) 12 Guide
  • Linux Ubuntu Redhat How To Extract Images from PDF
  • Linux and Windows Dual Boot Issue NIC Won't work After Booting Windows
  • Cisco CME How To Enable ACD hunt groups
  • How to install gns3 on Linux Ubuntu Mint
  • How to convert audio for Asterisk .wav format
  • Using Cisco CME Router with Asterisk as a dial-peer
  • Cisco CME How To Configure SIP Trunk VOIP
  • Virtualbox host Only Network Error Failed to save host network interface parameter - Cannot change gateway IP of host only network
  • Cisco CME and C7200 Router Testing and Learning Environment on Ubuntu 20+ Setup Tutorial Guide
  • Abusive IP ranges blacklist