If you are sure the binary/program exists, it could be that your PATH variable is broken or not set.
Just do this to set most of the common paths:
export PATH=$PATH:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin
There's no risk to the above, because it just takes your current PATH variable and adds more to what is already existing.
To make this permanent you can add this to your ~/.bashrc file........
This example is using RTL8821AU chipset from a TP-Link T2U Plus USB adapter and other similar ones should work the same.
Here's how to get this chipset RTL8821AU working in Linux.
Here's how to get RTL8812 and RTL8822 working in Linux.........
Edit your /etc/hostapd/hostapd.conf file like below and restart hostapd.
#WPS stuff
# Enable control interface for PBC/PIN entry
ctrl_interface=/var/run/hostapd
eap_server=1
wps_state=2
ap_setup_locked=1
wps_pin_requests=/var/run/hostapd.pin-req
config_methods=label display push_button keypad
#WPS model info stuff change to suit your needs
device_name=USB2.0 WLAN
manufacturer=ATHEROS
model_name=WAP........
This is certainly a poor design, as you can read many seasoned admins who have updated their iDRAC only to have it killed. One possible cause is not by doing all the incremental updates, doing updates from an old iDRAC to one many revisions newer is a sure way to kill things, but even then there is no guarantee based on the amount of failures.
List of threads of people's dead iDRAC's:........
This seems to happen in many different drivers but it happened more often in newer versions such as 530 vs 525.
Then nvidia-modeset goes to 100%
There are many reports of this appearing since driver 4.70 and I can confirm I've seen this in various machines.
https://forums.de........
Have you got this error from Apache?
[notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec)
[error] (28)No space left on device: Cannot create SSLMutex
At first glance it appears that you may be out of disk space but the issue is ipc or interprocess communication.
This will clear out the ipcs processes so things can work, this often happens during high traffic and may be a sign of DDOS.
The command below will fix it, it will list al........
Have you ever tried mounting a partition that you exists but you get this error?
mount: /mnt: can't read superblock on /dev/sda1.
The superblock in this example was bad because the physical disk had corruption and bad blocks/sectors. However, the data was generally accessible and you can always try this trick below (with caution and no warranty).
This is specifically for filesystems that place superblocks in multiple locations, which........
find /usr/share/zoneinfo/|sed s#"/usr/share/zoneinfo/"##g|grep "/"|grep -v posix|grep -v ^"Etc/"|grep -v ^right|grep -v ^"SystemV"
Africa/Addis_Ababa
Africa/Abidjan
Africa/Blantyre
Africa/Lusaka
Africa/Casablanca
Africa/Libreville
Africa/Asmara
Africa/Bujumbura
Africa/Dakar
Africa/Lagos
Africa/Malabo
Africa/Harare
Africa/Kigali........
Step 1.) Upgrade to Debian 11 first
The process to go to Debian 12 is not as smooth as 11, when trying to upgrade from Debian 10. In fact, it doesn't work directly, so you'll first need to follow this guide to update to Debian 11, reboot and come back here if successful.
Step 2.) Update sources.list
Update your /etc/apt/sources.list like this:
deb http://........
If you get this error, it is often because you have configured Apache with modules that weren't actually installed. Eg. you try to load the PHPmodule but didn't actually install the apache2 php module, so the server can't start. In general, this error can often be caused by issues with problematic modules and/or Apache being configured for modules that have not actually be installed (eg. libapache2-mod-php) is missing.
The above results in this less than obv........
This should work for most console ports of other manufacturers too. It is a quick and simple method for emegencies or deploying a few appliances/devices in a non-standard environment or small environment.
However, if this is a route thing, or the equipment is not physically close to you, it would be best to use some sort of "Terminal" server which is an IP connected switch with several serial ports built-in for this purpose. Normally they accessible by web/........
The issue is that Docker images are stripped down, so many tools and even python3 is missing, so you'll have to build or update the actual image yourself.
I assume you have started an image with something like this and that you have the Nvidia Toolkit installed (assuming you are using GPUs). If you're not using nvidia just remove --runtime=nvidia --gpus all.
docker run -it --runtime=nvidia --gpus all ubuntu bash
These works for most images li........
This has been a tried and true method for Windows because it is finicky with hardware changes without a reinstall (eg BSOD on boot is what happens 9/10 times unless you move to the same hardwar). Surprisingly, if you use a QEMU VM and do a standard install, it has worked in every system I've thrown the drive in afterwards.
So the play is this, use a USB SSD, physical SATA drive plugged internally or for convenience, you could use a SATA to USB adapter on another computer to perf........
If you plugin your phone to your computer and enable USB File Transfer/Allow on the phone side but the contents of your phone on the computer side are empty in the file manager, you probably don't have mtp-tools.MTP or media transfer protocol is the standard protocol that most phones use to communicate over USB to the computer.
Just do this to fix it and get access to your files:
apt install mtp-tools
After that you should be a........
In this example we install debian 10 with --variant=minbase which gives us a minimal/tiny install. Don't use variant if you want the full size install.
mkdir /tmp/deb10files
debootstrap --variant=minbase buster /tmp/deb10files/
Did you get an error?
debootstrap --variant=minbase buster /home/theuser/VMs/deb10files/
You'll get this error if you make a directory in your home........
Are you new to the company, datacenter or a third party who is responsible for deploying a fleet of servers from scratch.
The first step is to normally login to the KVM so you can perhaps manually reinstall, PXE boot the Cloud Image or reimage/reinstall an OS but you need access to the KVM/IP or what Dell calls iDRAC.
It's common that you may have forgotten this information or that another employee or colleague has changed the info and did not tell you, that they have left the........
If you are getting this error from systemctl "Loaded: masked (Reason: Unit hostapd.service is masked.)" we need to unmask the service.
Solution
systemctl unmask hostapd
Removed /etc/systemd/system/hostapd.service.
It's fixed
root@routerOS:/var/log# systemctl start hostapd
root@routerOS:/var/log# systemctl status hostapd
● hostapd.service - Access point and authentication server for Wi-Fi and Ethern........
Is your /var/log/journal overweight and bloated? For example a decent install of Debian 11 with most applications and services ends up being about 4.9G with the journal taking a few gigs.
du -hs /var/log/journal/
1.3G /var/log/journal/
By default in a lot of distributions there is no maximum size so it will keep growing. This is especially problematic for embedded distributions and devices, but is also a huge waste of sp........
Just use apt-cache policy to find the repo of a package:
apt-cache policy lxd
lxd:
Installed: 3.0.3-0ubuntu1~18.04.2
Candidate: 3.0.3-0ubuntu1~18.04.2
Version table:
*** 3.0.3-0ubuntu1~18.04.2 500
500 http://archive.ubuntu.com/ubuntu bionic-updates/main amd64 Packages
&nb........
The display manager is more so what controls the main graphical login process after Debian/Mint/Ubuntu boot and controls the graphical login sequence. Once you login, you are then usually passed to an Xorg based Window manager like XFCE, Mate, Ubuntu etc...
Popular display managers are mdm, gdm, lightdm etc... and they all basically do the same thing with a different interface/style and some feature differences.
In Mint for example the normal default display manager is l........
Install procps and it will install the other packages you need:
apt install procps
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following additional packages will be installed:
libgpm2 libncurses6 libprocps7 lsb-base psmisc
Suggested packages:
gpm
The following NEW packages will be ins........
The Best Docker Tutorial for Beginners
We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........
1. Let's work from an environment where we can install Ansible on.
If you are using an older version of Linux based on Mint 18 or Ubuntu 16, you may want to get the PPA and get the latest version of Ansible that way:
sudo apt install gpg
sudo add-apt-repository ppa:ansible/ansible
sudo apt update........
First of all make sure that you don't have the write-lock or write-protect switch enabled on the SDCard or USB drive.
If the above is not the case, then follow these instructions:
Solution - Clear Read Only Attribute
Hit "Windows Key+R" and enter "cmd" to enter the command prompt:
Now type the following :........
There aren't too many simple guides that show you how to use commands to setup your USB or other drive as a normal bootable drive where you can easily boot custom kernels or whatever OS you would like.
1. Get the tools we need:
We install "syslinux" for MBR and "syslinux-efi" for EFI and "MBR" as we need a tool that embeds the actual MBR into our USB:
sudo apt install syslinux syslinux-efi mbr........
It seems that QEMU/KVM's default PS2 mouse and keyboard doesn't work right in most cases. I have especially observed issues using Ctrl+C and Ctrl+V and in Linux you may see repeated key presses in the terminal and you will wonder why you copied something and it's not in the clipboard when you try to paste. The way to temporarily fix it is to press the key that is repeating once(works in Linux but not really in Windows).
Sometimes when moving your mouse it will also s........
How To Compile QEMU Manually (using sensible options)
1.) Download the QEMU source file you want.
wget https://download.qemu.org/qemu-4.2.0.tar.xz
2.) Extract The Source File
tar -Jxvf qemu-4.2.0.tar.xz
3.) Switch to the extracted source
cd qemu-4.2.0
4.) Make sure we have the right libraries and tools to compile QEMU manually
sudo apt install build-e........
It took a lot of fiddling to make a Huion Kamvas 13 Pro work in Linux but it simple once you know what to do. Don't bother searching as it is unlkely there is a guide out there that will actually make your tablet work.
It mainly comes down to the fact that the hid_uclogic kernel module is buggy or doesn't support MANYof these wacom based/Huion tablets properly.
What was happening with me is that Ihad the Kamvas 13 Huion setup as a secondary screen/monitor.&nb........
The best way to avoid this problem is to understand how your BIOS is setup to boot.
Often newer machines will default to U(EFI) which is different than the traditional MBR/Legacy mode.
The problem is that this may not be apparent, often a BIOS Boot Menu will show a Legacy Boot Option and EFIOption without defining it.
A good example of this is if your USB is called "Kingston" you may see in your Boot Menu "Kingston" and also "Ubuntu"........
Before you try to install and dual boot it is very important to understand the concept of "what boot mode your BIOS is in" and "what mode you booted the installer to".
Then follow the example of Linux Mint (but most Linux installers are very similar)to carefully understand WHERE you are installing your Boot Loader to whether that be MBR or EFI.
How Am IBooted?
First it's important to check your BIOS to see........
It really seems limited in that it can mainly give you the things you would see on the physical unit such as load etc..
wget https://downloads.sourceforge.net/project/apcupsd/apcupsd%20-%20Stable/3.14.14/apcupsd-3.14.14.tar.gz?r=https%3A%2F%2Fsourceforge.net%2Fprojects%2Fapcupsd%2Ffiles%2Flatest%2Fdownload&ts=1598115866
tar -zxvf apcupsd-3.14.14.tar.gz
cd apcupsd-3.14.14
[root@somebox apcupsd-3.14.14]#
./conf........
/usr/libexec/qemu-kvm -enable-kvm -boot order=cd,once=dc -vga cirrus -m 4096 -drive file=~/23815135.img,if=virtio -usbdevice tablet -net nic,macaddr=DE:AD:BE:EF:D4:AB -netdev bridge,br=br0,id=net0
qemu-kvm: -usbdevice tablet: '-usbdevice' is deprecated, please use '-device usb-...' instead
access denied by acl file
qemu-kvm: bridge helper failed
[root@CentOS-82-64-minimal 23815135]# /usr/libexec/qemu-kvm -enable-kvm -boot order=cd,once=dc -vga cirrus -........
This is the reason that I don't like the new ADATA USB drives such as the UV128/64GB or 128GB drives and other ones that look to be the same style (the green sliding USB connector).
They just don't work well from new and never work properly at any point.
[ 788.242463] usb 1-1.2: new high-speed USB device number 16 using ehci-pci
[ 788.339816] usb 1-1.2: New USB device found, idVendor=125f, idProduct=db8a
[ 7........
It is fairly simple to use once you know how to use it. However, the tricky thing is that by default it doesn't seem to be active or listen on any interface on manually specified.
How To Install ifplugd
First we install ifplugd
sudo apt install ifplugd
Let's enable it on our desired device(s)
vi /etc/default/ifplugd
set this line as so:........
Use fdisk on your USB drive to create a bootable NTFS partition (in my case /dev/sdb):
sudo fdisk /dev/sdb
Welcome to fdisk (util-linux 2.27.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Command (m for help): n
Partition type
p primary (0 primary, 0 extended, 4 free)........
A lot of times busy servers will have this issue and you cannot even force kill -9 the apachectl or httpd process:
[root@apachebox stats]# ps aux|grep httpd
root 1547 0.0 0.2 495452 32396 ? Ds Sep08 3:23 /usr/sbin/httpd
root 3543 0.0 0.0 6448 724 pts/1 S+ 13:11&nbs........
It is very silly but the default on the ifup-eth script tells dhclient ( the program that obtains a DHCP IPaddress if you have selected DHCPin your ifcfg-eth* config file) to EXIT / QUIT if the first attempt to obtain a lease fails.
No amount of dhclient.conf settings will fix this because if dhclient is started with -1 (which it is by default)then dhclient will quit.
This is obviously very bad for MOST cases. Say for example you have a power outage or........
Just edit your tftp file for xinetd like this:
*Change the IPto be the IPof the interface you want to listen on.
To test if your tftp is available on a certain IP range use nc -u yourip 69 to see if you can still connect (/var/log/messages or /var/log/syslog) should show the connection if it is open.
Oct 13 23:20:34 01 xinetd[26631]: Started working: 1 available servic........
service sshd status
● ssh.service - OpenBSD Secure Shell server
Loaded: loaded (/lib/systemd/system/ssh.service; enabled; vendor preset: enabled)
Active: failed (Result: start-limit-hit) since Wed 2019-10-02 11:07:54 EDT; 36s ago
Process: 476 ExecStartPre=/usr/sbin/sshd -t (code=exited, status=255)
Oct 02 11:07:54 box systemd[1]: Failed to start OpenBSD Secure Shell server.
Oct 02 11:07:54 box sys........
By default at least on Centos 7 nfs only allows 8 connections and starts 8 nfsd daemons.
To fix this edit this file:/etc/sysconfig/nfs
Edit the line "RPCNFSDCOUNT" (uncomment it so it looks like this:
RPCNFSDCOUNT=30
In the example above we are setting 30 nfsd daemons to run (or in other words 30 connections are possible this way).........
Now older versions of qemu-kvm didn't throw this error say if you just had "-video cirrus" when starting qemu-kvm. But newer versions do care.
And this probably only applies to you if you are running from bash/terminal with remote kvm images.
What you need to do is remove the "-video" part and just add -vnc :5
eg. this would fix the error:
qemu-system-x86_64 -enable-kvm -boot order=cd,once=dc -m 1024 -drive........
If you've just installed VBox and it is not starting or working, the most common problem is usually that you don't have your kernel source installed, which means there is no kernel driver for vbox so it can't work.
You may get an error that says "Kernel driver not installed" in your Virtualbox.
So the first thing you should do is install your kernel source by running this:
sudo apt-get install linux-headers-`uname -r`........
Install Errors on Version 12:
This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5
on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error.
*Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install.
What really causes this even though you successfully install........
If you get error messages like this it is usually because /var/run/sshd does not exist.
root@userbox:/# service sshd status
● ssh.service - OpenBSD Secure Shell server
Loaded: loaded (/lib/systemd/system/ssh.service; enabled; vendor preset: enab
Active: failed (Result: start-limit-hit) since Wed 2019-04-10 02:24:44 EDT; 1
Process: 511 ExecStartPre=/usr/sbin/sshd -t (code=exited, status=255)........
The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs.
qemu-kvm command:
/usr/libexec/qemu-kvm -version
QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard
........
You may have noticed if you are running QEMU/KVMmanually that in Windows the the position of the physical mouse does not match where the mouse is positioned within Windows.
There is an easy command to pass to qemu-kvm or qemu-system (whatever you call your binary):
-usbdevice tablet
The above flag will fix your mouse pointing problems whether you are running Windows 95, 98, NT, XP 2000, 2003, Vista, 7, 8 10 or Server 2000, 2003, 2008, 2012, 2016 or 2........
The net-tools command brings back all of the oldschool tools that we're used to:
/bin/netstat
/sbin/ifconfig
/sbin/ipmaddr
/sbin/iptunnel
/sbin/mii-tool
/sbin/nameif
/sbin/plipconfig
/sbin/rarp........
It was broken because of this package for xorg I installed:
xserver-xorg-core-hwe-18.04
Just remove it even if you have to chroot from a live USB/CD:
sudo apt-get remove xserver-xorg-core-hwe-18.04........
In a RAID array I had a have periodically lost a drive here and there over the past several months. Iwas always able to readd and resync without losing data. However at some point it looks like some minor corruption happened and this makes DRBD unhappy.
Using fsck did not help either.
Dec 19 06:01:45 storageboxtest4 kernel: [19005.945890] EXT3-fs error (device drbd0): ext3_get_inode_loc: unable to read inode block - inode=22184379........
Before getting into the output here is my typical experience with SMART, there is what I call a "bad disk" with pending and uncorrectable sectors that cannot be reallocated.
It has caused a kernel panic and system crash repeatedly as we can see from the logs.
But SMART says it has "PASSED" its self assessment. SMART is still useful to me but it is more about looking at Current_Pending_Sector.
Any time I have had anything but 0 for that attribute it........
systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system.
The key commands or arguments you will use with systemctl are the following:
Unit Commands:
list-units [PATTERN...] List loaded units
&nbs........
4.374647] usb_common: exports duplicate symbol usb_get_dr_mode (owned by kernel)
[ 4.403334] usbcore: exports duplicate symbol __usb_get_extra_descriptor (owned by kernel)
[ 4.427736] xhci_hcd 0000:00:15.0: xHCI Host Controller
[ 4.427844] xhci_hcd 0000:00:15.0: new USB bus registered, assigned bus number 1
[ 4.429040] xhci_hcd 0000:00:15.0: hcc params 0x200077c1 hci version 0x100 quirks 0x01109810
[ 4.429141] xhci_hcd 0000:00:15.0: cache line size of 64 is not sup........
[root@localhost:~]
BootModuleConfig.sh echo host-ind nfcd........
sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3
sudo apt-get install libcurl4-gnutls-dev
git clone https://github.com/wolf9466/cpuminer-multi
sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev
git clone https://github.com/fireice-uk/xmr-stak-cpu.git
make install
cd bin
chmod +x xmr-stak-cpu
./xmr-stak -O xmr........
nfs mount failed:
mount 10.10.2.20:/tmp/nfsmount /mnt/nfs/
mount: wrong fs type, bad option, bad superblock on 10.10.2.20:/tmp/nfsmount,
missing codepage or helper program, or other error
(for several filesystems (e.g. nfs, cifs) you might
need a /sbin/mount. helper program)
 ........
Sometimes if you have a very basic configuration OpenVPN on the client side for some reason sends all traffic to the OpenVPN server IP through the tun0 which is of course impossible and creates a block or routing loop.
This is because you need to use your normal ISP/LANgateway to hit the OpenVPN server if it is remote/offsite as is usually the case. So if you are connected to the OpenVPN through say a tun0 device and your routing is set to connect to the OpenVPN&nbs........
This is not the normal "black screen"issue and I was shocked to eventually find out why. The normal advice of reconfiguring Xorg didn't work. Even booting into "Recovery Mode" did not help.
Here is the short end of the stick that fixed it:
sudo apt-get install mdm mate-desktop-environment
Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled. This must be whe........
This works for almost all ISO's Ifind (at least Linux based):
sudo dd if=CentOS-6.9-x86_64-minimal.iso of=/dev/sdg bs=20M
20+1 records in
20+1 records out
427819008 bytes (428 MB) copied, 118.233 s, 3.6 MB/s
Of course change the .iso filename above and the /dev/sdg to your desired USB drive!........
It is well known hackers, the NSA, CIA and other groups have created malware to secretly turn on your webcam and microphone on your phone, tv etc.. But fortunately on our computers and laptops we have some options.
Most webcams use the "uvcvideo" kernel module / driver. You can disable this in two ways on boot. I recommend both just as a failsafe.
Disable it on rc.local once your system boots automatically
Add the followi........
I've never seen this before in all of my years. Ihave some very old CDs and DVDs 12-15 years old that seem not to work in this BD-R/DVD-R/CD-R Asus drive.
The discs are fine actually and ironically they even work fine on a normal LG USB based BD-R drive!
Here are the errors in Linux:
[2914936.884924] attempt to access beyond end of device
[2914936.884927] loop1: rw=0, want=730424, limit=688384
[2914954.556873] attempt to........
The easiest way is to use SSHand DD or a combination of netcat. SSHwill be a little slower due to encryption but is the most secure way (on two older systems the average clone speed is about 40-50MB/s). This is also OS independent as it doesn't matter what the source OS is because you are literallly cloning the drive so you retain the partition table and settings.
Clone HDD using SSH and DD........
By default Samba SMB/NMB listen on ANY and ALLIPs on your system by binding to 0.0.0.0. Obviously this is a huge security risk if you have a public facing server with both internal and external access. Usually when a system administrator sets up a samba server their intention is just to share with a LAN.
To do this you need to the following options under the [global] section in smb.conf
bind interfaces only = yes
interfaces = 192........
[Wed Sep 20 15:34:44 2017] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec)
[Wed Sep 20 15:34:44 2017] [error] Init: Unable to read server certificate from file /www/ssl-certs/server.crt
[Wed Sep 20 15:34:44 2017] [error] SSL Library Error: 218529960 error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag
[Wed Sep 20 15:34:44 2017] [error] SSL Library Error: 218595386 error:0D07803A:asn1 encoding routines:ASN1_ITEM_EX_D2I:nested asn1 error........
Essentially a program I was running for mining did not terminate properly with Ctrl+C it is listed as defunct and cannot be killed, kernel is tainted and normal tricks to disable the port are impossible the dev and sys entries for the device cannot be browsed or interacted with in any form without a lockup of the request. The only solution is to reboot due to the kernel taint as far as I can find so far.
[1130246.811056] INFO: task minerd:21861 blocked for more th........
#if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used
wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2
tar -jxvf ffmpeg-3.3.2.tar.bz2
cd ffmpeg-3.3.2/
./configure --disable-yasm
install prefix /usr/local
source path ........
This is a 8TB Seagate external USB 3.0 device apparently newer kernels use a module called "UAS" instead of "USB Storage" which causes issues as a lot of devices are not properly supported in UAS mode by the kernel driver. The solution some say is to disable UAS specifically for your USB device but I'd rather just disable UAS altogether.
Solution blacklist UAS: *do not do this it does not work and just causes your USB 3.0........
This is a VIA made VL805 USB 3.0 Chipset with 4-ports and MOLEX powered. First of all this unit was cheap at about only 9 USD with fast shipping. My biggest concern was if this was a quality unit and would it really give you full USB 3.0 speeds (some people reported with similar cards that for some weird r........
When running cudaminer once it tries to initialize the card the entire screen freezes. The computer itself is still running but the Xorg is done for, you cannot even switch to another console window and must reboot (even an mdm or Xorg restart does not help).
At first cudaminer will give you these errors:
stratrum_recv_line failed
...retry after 15 seconds
GPU #0: Geforce 210 with compute ca........
Here is a simple MP3 player and now there's a reason to understand why the supplied cable has some kind of capacitor and is very short. These devices can be VERY finicky and any voltage fluctuation or difference is enough to cause issues.
Take for example the error messages from Linux Mint:
[804829.895414] usb 1-1: USB disconnect, device number 11
[806961.109030] usb 1-1: new high-speed USB device number 12 using xhci_hcd........
*Update so this doesn't work it must be something to do with the path of nfs or something else but the installer fails with "Installer crashed" at the end whereas with the CD/USB it works.
This assumes you've already installed and configured a separate PXE/DHCP server somewhere else and your /tftpboot directory is setup.
This is for Linux Mint 18.1 but generally applies to most versions although you may have tro change things like "casper"........
This happens on any file an even just typing "vi"whereas it never happened before. I suspect an update or environment variable is causing this issue
When entering vi I get this weird stuff
line 58:
E488: Trailing characters: t_Sbet
line 63:
E171: Missing :endif
When exiting vi I get this weird stuff
t_Sb=^[[4%?%p1%{1}%=%t........
espeak - is horrible and sounds very old and robotic
echo "hello there"|espeak
#don't know how to use
mbrola and plugins
cicero
jovie just seems to be a graphical interface to espeak
There is also sbreader/sapi
Google's Text To Speech Works Quite Well
#!/bin/bash
say() { local IFS=+;/usr/bin/mplayer -ao alsa -really-quiet -noconsolec........
ecryptfs-mount-private
Enter your login passphrase:
Inserted auth tok with sig [ee16d84] "into the user session keyring
mount: No such file or directory"
[ 156.118113] ecryptfs_mount: kern_path() failed
[ 156.118431] Reading sb failed; rc = [-2]
[ 164.233055] traps: mate-notificati[3472] trap int3 ip:7f43d7002c13 sp:7fff162c6600 error:0
[ 166.017061] ecryptfs_mount: kern_path() failed........
This was a surprising bug but I unplugged all drives for an array md127. At first it was just 1 drive and mdadm seemed to notice this. I unplugged the second drive taking the array offline but mdadm did not realize it was offline and still showed a non-existent disk as being part of it. This created problems trying to unmount it or even to stop this array with mdadm freezing.
As for how to fix it I can only think of making sure you are not in a mounted path of........
Cannot even "Browse Network" when clicking on "Windows Network"
Unable to mount location
Failed to retrieve share list from server: No such file or directory
logs:
[2017/02/14 00:16:44.271314, 0] ../source3/nmbd/nmbd.c:58(terminate)
Got SIGTERM: going down...
[2017/02/13 17:35:41.797944, 0] ../lib/util/become_daemon.c:124(daemon_ready)
&........
[Thu Jan 26 14:13:31 2017] [notice] caught SIGTERM, shutting down
[Thu Jan 26 14:14:00 2017] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec)
[Thu Jan 26 14:14:00 2017] [error] Server certificate is expired: 'Server-Cert'
[Thu Jan 26 14:14:00 2017] [notice] SSL FIPS mode disabled
[Thu Jan 26 14:14:07 2017] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec)
[Thu Jan 26 14:14:07 2017] [error] Server certificate is expired: 'Server-Ce........
Uh oh
[17925926.174277] block drbd0: Handshake successful: Agreed network protocol version 96
[17925926.174325] block drbd0: conn( WFConnection -> WFReportParams )
[17925926.174342] block drbd0: Starting asender thread (from drbd0_receiver [1682])
[17925926.174432] block drbd0: data-integrity-alg:
[17925926.174581] block drbd0: drbd_sync_handshake:
[17925926.174586] block drbd0: self 2AAE66AF9252D6DB:2815BF........
I created a new partition table on a newly plugged in device and it caused fdisk to hang (even force kill does not work). It also may be a bad drive or some other issue because fdisk -l hangs after the first 2 HDDs (totaly of 8 HDDs on this system):
[1232879.903596] INFO: task fdisk:27176 blocked for more than 120 seconds.
[1232879.903607] Tainted: P&nbs........
It all comes down to a bug essentially where you are running an older kernel that doesn't support the newer Debian templates. The solution is to update your OpenVZ kernel.
Here are some symptoms of the problem/lack of kernel support:
Ubuntu Template 12.04 requires a manual network start:
service networking start
sshd will not start:
/usr/sbin/sshd
PRNG is not seeded
mknod /dev/random c 1 8........
Usually the cause is inexplicable because some things just don't work correctly even when calling all commands by their full path.
Usually adding the following to your crontab file at the top will fix/solve the issue:
SHELL=/bin/sh
PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin
........
At first my BIOS said the card may not work right because there is no more option ROM space.
I disabled the Option ROM for both LSI 1068 and 2008 chipsets, Network Boot ROM and most other PCI slots, Serial Port, etc... and the message went away but the card still does not work properly.
But it still cannot initialize the card properly(does not work):
[ 33.943272] NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:........
To check the version of Ubuntu just use the lsb_release command as shown below and you will be able to see the exact Ubuntu version you have installed.
lsb_release -a
No LSB modules are available.
Distributor ID: Ubuntu
Description: Ubuntu 14.04 LTS
Release: 14.04
Codename: trusty........
The Scenario
You have dual NICs and you disable NIC1 which uses 192.168.1.1 as its gateway. With NIC2 you enable it/connect it to another network which also has the gateway 192.168.1.1
Everything will work fine at this point.
When switching back to NIC1 even with NIC2 disabled and even unplugged, the OS basically can't pick up the new/updated ARP entry of the old device for 192.168.1.1 and perhaps thinks it is a security risk or spoof of some sorts and blocks i........
Add the following to fstab where 192.168.1.125/Media is the samba share and where /home/homeuser/Downloads is where you want to mount.
Change user and pass to what is needed (if no pass is required it still works fine with the below).
//192.168.1.125/Media /home/homeuser/Downloads cifs user=guest,pass=bla 0 0
mount: wrong fs type, bad option, bad superblock on //192.168.1.125/Media,
&nbs........
#solution
Edit /etc/yum.repos.d/openvz.repo
For the first two entries comment out #mirrorlist and uncomment #baseurl and then it worked
openvz yum problem Centos 6.5 cannot find file on mirror:
yum update
Loaded plugins: fastestmirror
Determining fastest mirrors
* openvz-kernel-rhel6: mirrors.ustc.edu.cn
* openvz-utils: mirrors.ustc.edu.cn
base ........
The solution was to reinstall the vbox dkms package and do a manual modprobe of the modules it makes.
I never sorted out the unable to start due to the USB issue, I did have the guest additions installed but the only way to boot was to change the pointing device from USB to PS2 and then to disable the USB controller (if your pointing device is set as USB, disabling USB will not work because it will re-enable by default when it sees your pointing device is USB, this is w........
0000:00:00.0 RAM memory: NVIDIA Corporation MCP55 Memory Controller (rev a2)
0000:00:01.0 ISA bridge: NVIDIA Corporation MCP55 LPC Bridge (rev a3)
0000:00:01.1 SMBus: NVIDIA Corporation MCP55 SMBus (rev a3)
0000:00:02.0 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a1)
0000:00:02.1 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a2)
0000:00:05.0 IDE interface: NVIDIA Corporation MCP55 SATA Controller (rev a3)
0000:00:05.1 I........
Based on this from Debian
The 'distribution' can be either the release code name / alias (wheezy, jessie, stretch, sid) or the release class (........
Dell CS24SC Info
0000:00:00.0 Host bridge: Intel Corporation 5100 Chipset Memory Controller Hub (rev 90)
0000:00:02.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x8 Port 2-3 (rev 90)
0000:00:03.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x4 Port 3 (rev 90)
0000:00:04.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x16 Port 4-7 (rev 90)
0000:00:05.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x4 Port 5 (rev 90)........
0000:00:00.0 Host bridge: Intel Corporation 5000P Chipset Memory Controller Hub (rev b1)
0000:00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 (rev b1)
0000:00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 (rev b1)
0000:00:04.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 (rev b1)
0000:00:05.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4........
It is a permissions issue that is hard to fix.
All but one USB device is greyed out.
I am already a member of "vboxusers"
I have already enabled and disabled USB support for the guest.
I have already reinstalled the latest VBOx guest editions
If running as root it all works fine
Changing........
#count=10000 makes an image of 10000MB make sure your image is at least the same as your existing
dd if=/dev/zero of=yourimage.img bs=1M count=10000
# losetup -fv newimage.raw
# fdisk -cu /dev/loop0
# kpartx -a /dev/loop0
# dd if= of=/dev/mapper/loop0p1
# e2fsck -f /dev/mapper/loop0p1
# resize2fs /dev/mapper/loop0p1
# a lot of guides tell you to edit /etc/fst........
yum -y install mathtools
Loaded plugins: fastestmirror
Loading mirror speeds from cached hostfile
* base: centos.mirror.rafal.ca
* epel: mirror.steadfast.net
* extras: mirror.agmn.ca
* rpmforge: repoforge.mirror.constant.com
* updates: centosb5.centos.org
extras ........
./configure
./configure: line 91: cd: /lib/modules/2.6.32-042stab084.25/build: No such file or directory
Error: kernel version not found.
Please make sure your kernel is configured.
dr-xr-xr-x. 4 root root 4096 Feb 21 06:13 ..
lrwxrwxrwx 1 root root 45 Feb 21 06:13 build -> ../../../usr/src/kernels/2.6.32-042stab084.25
drwxr-xr-x 2 root root 4096 Feb 12 20........
Failed to load VMMR0.r0 (VERR_SUPLIB_OWNER_NOT_ROOT)
In most cases the error above is useful, it generally means /usr or /usb/lib or /usr/lib/virtualbox is not owned by root and this is the cause of the error.
Solution
sudo chown root.root /usr/lib........
./configure
./configure: cannot locate gcc 3.x. please install it or specify with --qemu-cc
yum -y install gcc make
./configure
./configure: cannot locate gcc 3.x. please install it or specify with --qemu-cc
yum -y install compat-gcc-*
./configure
Error: Could not find alsa
Make sure to have the alsa libs and headers installed.
yum -y install alsa-lib-devel
./configure........
mount -o bind /proc /sda2/proc
mount -o bind /dev/ /sda2/dev
mount -o bind /sys /sda2/sys
chroot /sda2
mint / # mount -o bind /proc /sda2/proc
mint / # mount -o bind /dev/ /sda2/dev
mint / # mount -o bind /sys /sda2/sys
mint / # chroot /sda2
mint / # cd ~
mint ~ # ls
Desktop
mint ~ # cd /
mint / # ls
bin Desktop dev-temp home&nb........
Browse to this directory: ~/.config/libreoffice/3/user/backup/........
I've got one of these for testing projects from work at home and got more than I bargained for with the time I've spent on it due to the storage handing/Perc 6/i cards.
My particular model came with the following:
2U Rack Mount Server with Rails
2xOpteron 2373 EE (Quad Core, there is a 6-core version that can be found at times)
16GB RAM
2 x 250GB Seagate SATA
2 x Dell Perc 6/i (horrible and a nightmare to work........
I bricked one of my cards by following a guide from UNRAID.
Step #1 from them wipes out the BIOS, but guess what? The step where you restore the BIOS should have been done first, which is sas2flash but no version supports or is able to find my Perc 6/i. So now I'm a bit stuck.
I tried using megarec but it's funny that it can wipe the BIOS but can't forcefully reload it:
megarec -writesbr 0 mpt2sas.rom
Supports 1078 control........
One thing to remember is that you need MegaCli to do the flashing.
You also need the correct file,I tried at least 2 different Perc 6 firmwares from Dell that kept getting rejected as corrupt by MegaCli(they were really the wrong version). I have an external PCI-E Dell 6 Perc/I butI chose images from the 'Integrated" on motherboard version as it was allI could find. They are different, and below is my first time finding success.........
I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally.
I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli
wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN
--2013-08-26 12:53:39-- http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN
Resolvi........
LSi Megaraid
At first it was configured as a RAID 0, then I deleted the Virtual Disk Group.
I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing.
To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
Another new drive bad from the start:
Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen
Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error
Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC }
Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........
This is the most I can get when plugging in a hard drive hot and only on some power connectors.
[71656.314271] ata5: exception Emask 0x50 SAct 0x0 SErr 0x90a02 action 0xe frozen
[71656.314277] ata5: irq_stat 0x00400000, PHY RDY changed
[71656.314285] ata5: SError: { RecovComm Persist HostInt PHYRdyChg 10B8B }
[71656.314294] ata5: hard resetting link
[71660.360686] ata5: softreset failed (device not ready)
[71660.360694] ata5: applying........
This is useful for developing a lot of applications, I'm putting it here to keep it handy for myself and hopefully others:
Choose CountryCanadaJapanUnited StatesUnited KingdomAfghanistan........
This is something many people and especially businesses worry about, or at least they should. Before throwing away a hard drive, returning a hard drive, or especially Warrantying/RMAing it, you should wipe the drive.
Linux provides the "shred" and "dd" utlities which work quite well. It seems even a single pass is good enough but by default shred will do 3 passes.
Here's an example of using shred in Linux (I use a custom made distribution from........
I chose this because I heard a lot of stories about scams and that many providers I contacted said they can't unlock the Canadian I717s (one said "my Bell server" is down).
This method worked perfectly on my Bell I717M and should work for all I717 in Canada, I was able to insert a foreign SIMcard. This will work abroad too but remember entering CWM mode is different for I717's in other countries (at least theUS).
Step 1 - Root + CWM........
Step #1 - Create Wrapper Script
vi /usr/local/bin/phpsendmail
#!/usr/bin/php
........
This pops up when connecting the phone and it doesn't seem to charge. The phone keeps showing a status message every few seconds "Connected as a media device".
It's ridiculous why this phone doesn't just default as a simple USB Mass storage device.
Here's what I see in /var/log/messages:
Jan 30 18:51:27 QuadCoreAM2 kernel: [18038228.144046] usb 1-3: new high speed USB device using ehci_hcd and address 24
Jan 30 18:51:28 QuadCoreAM2 ke........
This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel.
I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk.
I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one).
This is strange but it seems like this Xen PV guest has some sort of hidden or........
I've run into two issues with Lantronix based KVMs on various servers and here's how I solved them (with that said I like these units as they are Java based and OS independent and work very well, unike some other models like Startech).
1.) If you are connected by USB only and you're sure USB support from the BIOS is enabled, you just need to click the following in Lantronix
Interfaces -> Keyboard/Mouse
Check "Force USB Full Speed Mode", this fixed the issu........
The best way is to use rsync, I've set it up so it doesn't copy unnecessary files, or at least ones I'm sure aren't needed.
Here is the rsync command Iused (adapt to your specific Thunderbird profile location):
rsync -hazv user@remotehost.com:/home/user/.thunderbird/sbrer.default/* /home/user/.thunderbird/4nyb0.default/ --exclude=global* --exclude=Cache --exclude=ImapMail --exclude=Mail
This is a great way to get your e-mail accounts going on a new c........
*************************************
* *
* All parts have been installed *
*........
I experienced this with CPanel's Exim after an auto-update (a Google of this error produces lots of complaints with few clear solutions). In this case I'll put the solution at the top.
Run /scripts/buildeximconf to rebuild the Exim config and it should be fine after that.
mail -vs "from test" user@dest.com < .bash_history
LOG: MAIN
cwd=/root 4 args: send-mail -i -v user@dest.com
LOG: MAIN
&........
One of my test Centos 5 containers was on a partition that filled up and it threw all sorts of errors and stopped responding but now I can't boot it again anymore.
All the console shows is the Linux Penguin on the top left corner and the xm console says "usbcore: registered new driver hub" and has halted there.
Centos 5 Xen container stuck/frozen won't boot on "usbcore: registered new driver hub"
Another great way of troubleshooting is booting fro........
This is one in a series of weird things whichIthought was motherboard related (I RMA'd the motherboard), the RAM tests fine with memtest86 and I used badblocks on both RAID 1 members with no errors and smartctl is happy with them.
Basically the array crashes the kernel a lot and has issues when writing.
[112322.723465] md0: rw=0, want=14958668696, limit=1887460480
[112322.731077] attempt to access beyond end of device
[112322.731087] md........
*Make sure that the ownership is 501.501 or mobile.mobile when copying back (especially if using ssh or sftp as root on the iPhone) otherwise things will break. Eg. the contacts will be blank even after trying to update due to incorrect ownership/permissions.
iPhone Notes Location/Restore:
/private/var/mobile/Library/AddressBook
AddressBookImages.sqlitedb AddressBook.sqlitedb
Once you restore the contacts and restar........
yum -y install vnstat
chown nobody.nobody -R /var/lib/vnstat/
#replace venet0 below with your desired interface
sudo -u nobody vnstat -u -i venet0
#edit: vi /etc/sysconfig/vnstat
#VNSTAT_OPTIONS="-i venet0"
# only use the sed below if you are using venet0 instead of eth0 or replace accordingly
sed -i 's/eth0/venet0/g' /etc/sysconfig/vnstat
[root@monitor]# yum install vn........
You need to enable the httpd daemon with monit to actually view the status and control, it's not only for the web interface since the httpd is theONLY way of controlling monit and viewing the status.
monit monitor all will also reinstate disabled services if they've timed out too much. Just restarting the service will do nothing to re-monitor a service that monit has stopped monitoring due to too many failures.
*Also note that /etc/monit.conf i........
My mother needed a new laptop and I recommended her the same one I would have bought myself or my wife, that means the cheapest possible laptop with the most features for the money.
This HP shines at this price point and one thing that made me stay away from buying more and recommending HP/Compaq was the poor battery life. Not anymore, this model has an industry leading up to 4 hours of battery life.
Key Factors for Choosing It:
HDMI Out........
I don't expect this to be solved soon but some of Yahoo's DNS servers are out of whack. I changed the IPs of some nameservers of some domains and now most Yahoo users can't e-mail to those domains!
As you can see below by the "No MX or A records for mychangedomain.com", now Yahoo's DNS/mailserver DNS cache is wrong. You would think they would at least have cached the old incorrect records, but instead for some reason their DNS cache has no entry and doesn't seem........
high IO wait
424 root 39 19 1900 848 552 D 0.0 0.0 0:00.91 updatedb
root 424 0.0 0.0 1900 848 ? DN Mar11 0:00 /usr/bin/updatedb -f sysfs?rootfs?bdev?proc?cpuset?binfmt_misc?debugfs?sockfs?usbfs?pipefs?anon_inodefs?futexfs?tmpfs?inotifyfs?eventp........
Santrex Review/Scam/Complaint
Santrex never provided any working server, I believe it was just a dummy management Solus server because the server said it was booted but never connected to the console. I complained to them and eventually the support admitted the server was not working and to wait for 24 hours. I waited for 4-days, after which they sent an e-mail saying my service was being disabled for SPAM ...(when SolusVM shows 0kb of traffic). Th........
These are the only two I've encountered but here is the low-end and note my story is not at all unique.
In my case I was scammed out of money and did not receive any service at all from either company.
Santrex Review/Scam/Complaint
Santrex never provided any working server, I believe it was just a dummy management Solus server because the server said it was booted but never connected to the console. I complained to them and eventually the support adm........
Centos 5 Postfix and SPAMASSASSIN Tutorial
yum install spamassassin
chkconfig spamassassin on
vi /etc/mail/spamassassin/local.cf
##############
#required_hits 5
#report_safe 0
#rewrite_header Subject [SPAM]
#5 is the least restrictive (means only the most obvious SPAM is caught. 0 is obviously the most restrictive/sensitive and would have lots of false positives
require........
Convert MBOX Mail files into Maildir using Linux
*You need perl an the TimeDate module
Get the free Perl script mb2md from the project/author's site:
wget http://batleth.sapienti-sat.org/projects/mb2md/mb2md-3.20.pl.gz
gunzip mb2md-3.20.pl.gz
#remember you need timedate or you'll get this error:
./mb2md-3.20.pl
Can't locate........
Jan 16 04:02:03 centosbox syslogd 1.4.1: restart.
Jan 16 04:07:34 centosbox kernel: INFO: task updatedb:20771 blocked for more than 300 seconds.
Jan 16 04:07:34 centosbox kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
Jan 16 04:07:34 centosbox kernel: updatedb D F78BE050 6476 20771 20766&n........
CPU/Kernel/MB/RAID problem?
Jan 5 12:45:05 testbox kernel: [653298.890004] BUG: soft lockup - CPU#0 stuck for 61s! [hal-acl-tool:4168]
Jan 5 12:45:05 testbox kernel: [653298.890005] Modules linked in: vmnet vmci vmmon binfmt_misc drbd video output input_polldev ocfs2_stackglue ocfs2_dlmfs ocfs2_dlm ocfs2_nodemanager configfs k8temp hwmon_vid lp snd_hda_intel snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi........
I found the cause of this issue was from all the diskspace being used but clearing it was not enough. Iguess the tables became inconsistent when space ran out and myisamchk is what fixed the rest.
service mysqld restart
ERROR! MySQL manager or server PID file could not be found!
....................................................................................... ERROR! Manager of pid-file quit without updating file.
se........
I've only used it on Centos, soI thought I'd make a quick Debian guide:
Install the DRBD Package
apt-get install drbd8-utils
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following packages were automatically installed and are no longer required:
libswfdec-0.8-0
Use 'apt-get autoremove' to remove them.
The following........
I separated the 2 drives in the RAID 1 array.
1 is the old one /dev/sda and is out of date, while the separated other one /dev/sdc was in another drive and mounted and used with more data (updated).
I wonder how mdadm will handle this:
usb-storage: device scan complete
md: md127 stopped.
md: bind
md: md127: raid array is not clean -- starting background reconstruction
raid1: raid set md127 active with 1 out of 2 m........
The solution is simple but it's a wonder why VBOX doesn't address it directly?
Perhaps newer versions will but you have to add your user to the "vboxusers" group and then login and logout and you'll see the devices you wanted but couldn't access are now available.
The weird thing is that the grayed out issue doesn't happen with all devcies but one notable thing is the Apple iPhone especially in DFU or Recovery Mode which is an big issue for some people.........
2010:09:09-22:22:11: The ip of this machine (xx.xx.xx.xx) does not match the ip in the license file.
Check the value of your ethernet_dev=venet0:0 setting in your /usr/local/directadmin/conf/directadmin.conf file and the output of /sbin/ifconfig
Solution
/usr/local/directadmin/scripts/getLicense.sh........
This was done on Centos butI think it's easier on Debian machines, the paths that it is set to use are tailored towards Debian, so there is some fiddling that needs to be done on Centos.
This is for chrooting ssh, but jailkit has other uses than just SSH jails but I won't cover them in this writeup.
1. Install jailkit
yum install jailkit
2. Setup Jail Home
mkdir /home/jail
chown root:root /home/ja........
After installation Directadmin does not work on OpenVZ VPS when browsing http://ip.ip.ip.ip:2222
service directadmin status
directadmin dead but pid file exists
tail /var/log/directadmin/error.log
Check the value of your ethernet_dev=eth0 setting in your /usr/local/directadmin/conf/directadmin.conf file and the output of /sbin/ifconfig
2010:07:10-12:44:01: ioctl can't find........
Mencoder is great, you can throw anything at it, including video files from your camera and have it encode into xvid or almost any other format.
In my case I took 640x480 video from my Canon and reduced the size by 1/3 with the options below (there are many other options that you can read about in the manual but I like to keep it simple).
Mencoder Encode
mencoder -ovc xvid -oac mp3lame -xvidencopts fixed_quant=4 -o ........
I finally decided to look into some utils that did this, and the first one I found is "mp3burn". It is unbelievable simple and perfect. *2017-11 update and mp3burn is still available in standard repos such as Ubuntu 14/16 so this is a current and working project.
Just install the package and it gets all required libraries to convert and then burn's on the fly. And you won't believe how simple it is.
I just want to a directory that had the MP3's I wanted t........
This is obviously a bug in the r8169 kernel module and it seems to affect a lot of people. I upgraded to the latest kernel and hope this won't happen anymore, as it is a very serious error. This is especially serious for those who are running servers with this chipset, who can afford for the NIC to randomly go off-line for no apparent reason?
[655548.189113] type=1505 audit(1277067560.902:5): operation="profile_load" name="/usr/bin/freshclam&q........
My XBOX's dashboard/firmware was from sometime in 2008 when I first bought the system. I mainly played using composite cables but at my brother in law's house we used HDMI. The very first time it worked, but then I bought some games that did some update and after that HDMI never worked.
The symptoms besides having on sound is that your XBOX will show PC monitor resolutions but won't have any option to say you have a 720P or 1080P display, this means the XBOX firmware is fa........
I've never understood how to enable and disable services for different run levels in Debian based distros, it's just weird, annoying and doesn't make sense. I much prefer chkconfig from RHEL.
Just install the package called 'rcconf' and be done with it. rcconf makes things easy for you.
apt-get install rcconf
Reading package lists... Done
Building dependency tree
Reading state information... Done........
Basically the two main types of distros are Debian and RHEL/Centos based. I'm just going to give a quick overview of how the configuration of IP interfaces works in Debian/Centos based distros.
*Just one thing to remember, when setting IPs statically you have to manually specify a DNS server in /etc/resolv.conf (since DHCP is what normally does it automatically)
Debian/Ubuntu/Kubuntu/MEPIS
The IP (DHCP &........
I'm not impressed with this motherboard, I was impressed with my Gigabyte AM3 board which seems to work flawlessly.
Everyone knows that the firmware is flawed, even though I have the F6, it still seems that the system doesn't reset properly or quickly enough.
Another HUGE problem is that in most Linux kernels the NIC won't work (if you try 10 times by rebooting it might). I also notice that you need to power down for it to work.
This board does not seem very com........
This was unbelievable how much the Xen kernel slows things down, keep in mind both tests were done on the hostnode, one was with the Openvz-Xen hybrid kernel and the other was just OpenVZ. You can see the performance difference is nearly 300% better when not using the Xen kernel.
OpenVZ-Xen Kernel Test Results (I was wondering what was wrong/so slow with my Core i5!)
# # # # # #&n........
It's not just as simple as running the chroot command, you need to ensure the /proc and /dev entries are passed through and populated to the chroot environment.
Step 1 - Mount Your Off-lineOS
mount /dev/sda1 /mnt
Step 2 - Mount Proc
mount -t proc none /mnt/proc
Step 3 - Mount Dev
Most guides will tell you to use this: mount -o bind /dev /mnt//dev but that doesn't work for some reason in many cases:
mount: wron........
I'm not a fan of Asus and won't be buying another because of having to fight Asus over a bogus warranty denial (it's a long story but they only replied about how to RMA my unit weeks later on the EXACT day the warranty expired).
Anyway, it's just a matter of hitting F9 to do this, there's no need to worry about booting from USB or CD (unless of course you want a different OS eg. Windows XP Pro, Vista/7, or a flavor of Linux or Unix). Also remember that you need to fully/properl........
Proxmox has made this free utility to backup running OpenVZ containers. It's a great program which is actually just a PERL script but gets the job done. This program is not 100% required because all it really does is cp -a from your container's path as far as I know but it is still good to have uniformity to how you backup your containers.
For RPM distros such as Centos/RHEL/Fedora etc.. download and install this:
wget http://www.proxmox.com/cms_proxm........
Here are the results, it is Sempron 3000+ AMD Mobile, 500Gig HDD, 512MB RAM with shared ATI Radeon graphics.
# # # # # # # ##### ###### # # #### # #
# # ## # # # #&nb........
Convert PS2 controller to PC USB ControllerSuper Joy Box 3 Pro
http://www.play-asia.com/paOS-13-71-6m-49-en-70-qc2.html........
Need identd for port 113 ? Install authdyum install authd
Happy identing :)Actually it's not that simple.
It installs as an "xinetd" service and is disabled and turned off by deafult.
To enable it run:
[code:1:8c94df8319]
chkconfig --level 3 auth on
service xinetd restart
[/code:1:8c94df8319]
This will set identd aka authd to start by default.
service xinetd resta........
ECS K7S5A Motherboard System Take Up To 2 Minutes To BootHi guys,
My motherboard is very strange. Sometimes it will take up to a few minutes to post. I have no idea it suddenly started doing this. I have tried everything and all I can figure is that it is somehow related to the USB ports possibly.
Why do I say this?
Because if I disconnect my scanner the problem occurs less frequently. I only have a printer hooked up to USB now and by........
Broadband PreferencesLet's see what people prefer.........
auth/auth_util.c:make_server_info_sam(840)
User nobody in passdb, but getpwnam() fails!
I never found the solution to this in the web, as usual so Ithought I'd post the fix. In plain English smbd is telling us that the user "nobody" does not exist in /etc/passwd.
You can simply add this to your /etc/passwd file like so:
nobody:x:65534:65534:nobody:/nonexistent:/sbin/nologin
Now SAMBA/smbd should........
This really is a difficult and confusing process for non-Mandarin speakers, but here's what I've done and learned so far:
You can purchase an "M-Zone" China Mobile pre-paid SIMCard from almost anywhere but I tried to purchase mine from Suning (a large electronics dealer) hoping they would be able to help me or answer my questions but my plan didn't work out at all. At Suning once I found someone who spoke some English they gave me the 55 RMB M-Zone China Mobile P........
Everyone says there is a "manual" way of doing it and then they tell you to use iTunes, but if you're like me, you're travelling on business in a foreign country and your laptop does not have iTunes and you don't have a way of getting it and/or don't want it.
For this example I'm using the provider "du" in Dubai, UAE (United Arab Emirates) but this method works for virtually all providers.
The requirements in this case to truly "manually update........
Backing MySQL Databases
Backing Up/Dumping All Mysql Databases To A Single File
mysqldump --all-databases -u admin -p > allmysqldatabases.sql
The "-all-databases" clause is pretty obvious isn't it? It means that it will backup all databases.
The "-u admin" means login using the user "admin", if you h........
This is the Intel Atom 330 motherboard with integrated Realtek Gigabit NIC (Intel Desktop Board D945GCLF2 Motherboard W/ Atom 330 1.6 GHz Dual Core Processor - Mini-ITX)
I cannot achieve more than 15 MB/s, even doing a local transfer through eth0 to it's own IP.
100% 95MB 15.9MB/s 00:06
So this is not a cabling, switch or hardware issue, it seems like a driver or chipset limitation problem.
Here is my........
When trying to even cd or ls the mounted OCFS2 partition it crashes. Ithink this is a combination of VMWare Server's problem and the way I mounted and symlinked to it.
More than anything this shows the problem and lack of forsight with VMWare, but also that OCFS2 is easily crashed if you do strange things.
Output of /var/log/messages for OCFS2
Apr 10 15:57:45 localhost kernel: [84331.691258] Modules linked in: vmnet vmci vmmon ocfs2_stac........