Mint Ubuntu Linux Gnome Showing Home Directory on Desktop instead of Desktop Directory

During a migration or other custom setup, it's possible you don't have a $HOME/Desktop and as a result the config file that controls this is set to just use your $HOME directory. This is controlled in the file: $HOME/.config/user-dirs.dirs As we can see below, Desktop, Downloads, Music and Pictures are set to $HOME. We can edit any of these as we like. # This file is written by xdg-user-dirs-update # If you want........

Virtualbox Best Networking Mode In Lab/Work Environment without using NAT Network or Bridged

Virtualbox is a very powerful tool, but for some use cases it is less than optimal. Say you are in a work, lab or other environment where you are not alone on the physical network and there could be overlap of IPs, but you need all of your VMs to be contactable from your host, VMs need to communicate with each other, and VMs need internet. NAT Network will give you VM to VM communication and internet, however, it is buggy and unstable. It also doesn't allow host to VM co........

Linux How to Check Which NIC is Onboard eth0 or eth1 Ubuntu Centos Debian Mint

So say you happen to have 2 NICs of the exact same chipset, they will generally show up as the same name, with possibly a different revision in lspci. Normally this is not an issue if you have a server with 4 NICs, generally the eth0 to eth3 appears from left to the right (or right to left on some vendors) so it doesn't take much figuring out. Generally if you have different chipsets for different NICs, it should be easy to know which one is eth0 or the first NIC in the OS.........

i915 nouveau Nvidia GPU not starting lightdm Xorg failing solution for Could not determine valid watermarks for inherited state

It may appear to be an Xorg or lightdm/gdm/mdm error but in reality for many users with this issue, it's a driver conflict and issue. I had a system that had two GPUs, an Intel and Nvidia GPU. The only thing that got it working was to remove the nouveau driver and blacklist it so it never came back, then the Intel GPU works fine without these issues. Solution sudo rmmod nouveau add nouveau/other driver to blacklist edit th........

LightDM Mint Ubuntu Debian won't start errors Nvidia Graphics

This error implies that there may be an issue with Xorg or maybe your NVIDIA GPU cannot start or initialize: 35 laptop kernel: [ 2031.857704] nvidia: loading out-of-tree module taints kernel. 35 laptop kernel: [ 2031.857724] nvidia: module license 'NVIDIA' taints kernel. 35 laptop kernel: [ 2031.857725] Disabling lock debugging due to kernel taint 35 laptop kernel: [ 2031.873280] nvidia: module verification failed: signature a........

How To Do Linux Network Bonding Teaming in Mint Debian Ubuntu

Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........

Docker Tutorial HowTo Install Docker, Use and Create Docker Container Images Clustering Swarm Mode Monitoring Service Hosting Provider

The Best Docker Tutorial for Beginners We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........

How To Create OpenVPN Server for Secure Remote Corporate Access in Linux Debian/Mint/Ubuntu with client public key authentication

Why choose OpenVPN instead of a firewall appliance? OpenVPN can be a reliable and easy replacement for traditional hardware or just be an additional tool that your company uses so that the firewall can focus on its job rather than acting as a VPNappliance at the same time. When comparing OpenVPN with traditional firewal........

Wazuh / OSSEC Install and Configuration Howto Tutorial Guide for Monitoring Agents SIEM

How To Install Wazuh Server / Quickest Installation Wazuh (forked from the well known OSSEC project) is a full SIEM (Security Information Event Management) that works extremely well with the platforms it natively supports as an "Agent", which allows you to do scans of everything such as all processes running, CVE vulnerability check, incident reporting etc... Prerequisites: A lot of issues with Wazuh seem to be caused by i........

How to install Kubernetes with microk8s and deploy apps on Debian/Mint/Ubuntu Linux

Kubernetes Easy Beginners Tutorial/Architecture Guide Kubernetes is known as container orchestration and we should start at explaining the container part of it. A Container is what runs the actual application and based on an Image, and are more comparable to something like an LXC Container, Virtuozzo/OpenVZ using the Linux Kernel Namespaces feature. Containers run these images as independent, isolated operating environments under the O........

Juniper JunOS Command Overview and Howtos Switch, Router, Firewall Tutorial Guide

Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........

Mikrotik RouterOS CHR/ISO Basic and Quick Setup Howto Guide

Many people may not be aware that you can turn commodity hardware into a Mikrotik OS and there are various options which is "CHR" (Cloud Hosted Router) which is a VMimage meant for Virtualization only (seriously, I've tried to dd the image to a physical server and it just crashed as it does not contain any drivers for physical). One note as well if you are trying to do a baremetal install you may get an error "Error Loading Operating System" or........

dynagen / dynamips 100% high CPU usage solution - how to set the idlepc value

The idlepc value is very important to dynamips and it is both image and often CPU dependent. There is no "magic"value that will work for all images and all CPUs so this is why I'll show you a quick and handy way. Also don't be disappointed, some values do not work well but idlepc gives you several. For example in my example below #6 didn't help at all but #7 got me down to about 6% CPU from 99-100%. *Befo........

Linux Mint/Debian/Ubuntu/Centos Installer black grub screen and blank screen after trying to boot installer or main OS

This happens to a lot of Nvidia users especially users of newer cards like the RTX series. If for example you are trying to boot and install Linux and you get a black and white grub2 screen instead of a nice graphical welcome installer, you probably suffer from this bug. It is normally followed by the user booting and finding they just have a blank/black screen. Here is the quick flow of steps to fix it: If you get a black grub scree........

Radeon R3 GPU on Debian Crashing

Occasionally my whole screen locks up and I cannot even swith to the console and I find this in my syslog: *-display description: VGA compatible controller product: Mullins [Radeon R3 Graphics] vendor: Advanced Micro Devices, Inc. [AMD/ATI] ........

apache symlinks denied even with followsymlinks

Symbolic link not allowed or link target not accessible: /path/httpdocs/news.html There are a few reasons that can cause this message and this is for people who have ruled out the basics, eg. your symlinks are enabled and the right permissions are applied (but read on to learn about ownership requirements above the directory in question). So there are a few key things here that cause Apache not to follow symlinks:........

how to use ifplugd in Linux to execute a command or script when a NIC cable is unplugged or plugged in

It is fairly simple to use once you know how to use it. However, the tricky thing is that by default it doesn't seem to be active or listen on any interface on manually specified. How To Install ifplugd First we install ifplugd sudo apt install ifplugd Let's enable it on our desired device(s) vi /etc/default/ifplugd set this line as so:........

Bind / named not responding to queries solution

By default bind will not respond to outside queries for security reasons. In most distributions you will find the default in /etc/named.conf looks like this at the top under options: listen-on port 53 { 127.0.0.1; }; listen-on-v6 port 53 { ::1; }; directory "/var/named";........

Cisco Unified Communications Manager / CUCM IP 8.6,10,12 Install Error Solution

Install Errors on Version 12: This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5 on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error. *Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install. What really causes this even though you successfully install........

Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM

The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........

Linux Mint XWindows Ubuntu MATE or Cinnamon How To Restart The GUI / Graphics / Session if it freezes without losing current windows or programs

Uh oh, so you're working on some super l33t code or other stuff that is super important and Linux Mint's MATE or Cinnamon window manager freezes. This means maybe you can move your mouse but you can't click anything, you can't Alt + Tab to another program but everything appears to be working other than that. The first thing you would do is Ctrl + Alt + F1 (or whatever virtual terminal you want) and get into the Linux bash prompt (the black screen where things really happen :))........

Why SMART is not smart at all and doesn't properly predict disk errors that cause a kernel panic or crash

Before getting into the output here is my typical experience with SMART, there is what I call a "bad disk" with pending and uncorrectable sectors that cannot be reallocated. It has caused a kernel panic and system crash repeatedly as we can see from the logs. But SMART says it has "PASSED" its self assessment. SMART is still useful to me but it is more about looking at Current_Pending_Sector. Any time I have had anything but 0 for that attribute it........

How Does Cisco CUCM (Cisco Unified Communication Manager) Work?

Cisco's CUCM (Cisco Unified Communication Manager) is a system that combines voice, video, data and mobile products into a single unified management suite. At its core, the CUCMis like a "Super PBX" that controls the flow of all communications through an organization even single or multiple site deployments. Cisco's CUCMmakes communication more effective and simple through centralized management and unification of communications resources.........

hwloc-nox set CPU affinity in Linux

sudo apt-get install hwloc-nox Reading package lists... Done Building dependency tree Reading state information... Done The following NEW packages will be installed: hwloc-nox 0 upgraded, 1 newly installed, 0 to remove and 530 not upgraded. Need to get 151 kB of archives. After this operation, 453 kB of additional disk space will be used. Get:1 http://archive.ubuntu.com/ubunt........

VMWare ESXi 6.7 SSH/PowerShell CLI Commands

[root@localhost:~] BootModuleConfig.sh echo host-ind nfcd........

Debian Mint Ubuntu compiling xmr-stak

sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........

vino server error cannot login

10/07/2018 03:05:14 PM [IPv4] Got connection from client10.10.25.1 10/07/2018 03:05:14 PM other clients: 10/07/2018 03:05:14 PM Client Protocol Version 3.7 10/07/2018 03:05:14 PM Advertising security type 18 10/07/2018 03:05:14 PM Client returned security type 18 10/07/2018 03:05:14 PM TLS Handshake failed: Could not negotiate a supported cipher suite. 10/07/2018 03:05:14 PM Client10.10.25.1 gone 10/07/2018 03:05:14 PM Statistics:........

OpenVPN cannot ping remote IP routing loop issue after connecting

Sometimes if you have a very basic configuration OpenVPN on the client side for some reason sends all traffic to the OpenVPN server IP through the tun0 which is of course impossible and creates a block or routing loop. This is because you need to use your normal ISP/LANgateway to hit the OpenVPN server if it is remote/offsite as is usually the case. So if you are connected to the OpenVPN through say a tun0 device and your routing is set to connect to the OpenVPN&nbs........

Linux Mint Black Screen after boot no graphics solution

This is not the normal "black screen"issue and I was shocked to eventually find out why. The normal advice of reconfiguring Xorg didn't work. Even booting into "Recovery Mode" did not help. Here is the short end of the stick that fixed it: sudo apt-get install mdm mate-desktop-environment Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled. This must be whe........

ffmpeg Linux Mint download, compile and install howto

#if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2 tar -jxvf ffmpeg-3.3.2.tar.bz2 cd ffmpeg-3.3.2/ ./configure --disable-yasm install prefix /usr/local source path ........

Centos 7 Cudaminer Nvidia setup guide

I am using a GTX 1060 but replace the download for the driver with the correct/current version for your particular card by visiting: http://www.nvidia.com/Download/index.aspx?lang=en-us yum install automake curl openssl-devel libcurl-devel gcc gcc-c++ yum -y install kernel-devel-`uname -r` yum -y install unzip #the........

Linux Mint Intel Screen Tearing Horizontal Line Solution Fix Intel i915 Intel HD 4400 GPU Debian / Ubuntu

sudo mkdir -p /etc/X11/xorg.conf.d/ sudo vi /etc/X11/xorg.conf.d/20-intel.conf On newer Ubuntu / Mint / Debian systems the file would go in: /usr/share/X11/xorg.conf.d/20-intel.conf Type "i" and enter the following: Section "Device" Identifier "Intel Graphics" Driver&n........

Linux Mint/Ubuntu/Debian Nvidia driver becomes slow graphics performance issue

I've had this issue since Ubuntu 9 and now even on Linux Mint 17 no matter what latest version of the Nvidia proprietary driver that I use. It just becomes slower and slower and only gets better after rebooting or restarting Xorg. Someone here has it as well https://askubuntu.com/questions/822449/graphics-becomes-slow-after-a-while/917886 It's very fru........

Nvidia Linux Card not working due to LSI 9200/SAS2008 IRQ conflict

At first my BIOS said the card may not work right because there is no more option ROM space. I disabled the Option ROM for both LSI 1068 and 2008 chipsets, Network Boot ROM and most other PCI slots, Serial Port, etc... and the message went away but the card still does not work properly. But it still cannot initialize the card properly(does not work): [ 33.943272] NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:........

Linux Mint/Ubuntu/Debian Dual NICs networks problem when enabling and disabling one device

The Scenario You have dual NICs and you disable NIC1 which uses 192.168.1.1 as its gateway. With NIC2 you enable it/connect it to another network which also has the gateway 192.168.1.1 Everything will work fine at this point. When switching back to NIC1 even with NIC2 disabled and even unplugged, the OS basically can't pick up the new/updated ARP entry of the old device for 192.168.1.1 and perhaps thinks it is a security risk or spoof of some sorts and blocks i........

Dell CS24-NV7 lspci dmidecode info

0000:00:00.0 RAM memory: NVIDIA Corporation MCP55 Memory Controller (rev a2) 0000:00:01.0 ISA bridge: NVIDIA Corporation MCP55 LPC Bridge (rev a3) 0000:00:01.1 SMBus: NVIDIA Corporation MCP55 SMBus (rev a3) 0000:00:02.0 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a1) 0000:00:02.1 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a2) 0000:00:05.0 IDE interface: NVIDIA Corporation MCP55 SATA Controller (rev a3) 0000:00:05.1 I........

Dell CS24SC Server Info

Dell CS24SC Info 0000:00:00.0 Host bridge: Intel Corporation 5100 Chipset Memory Controller Hub (rev 90) 0000:00:02.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x8 Port 2-3 (rev 90) 0000:00:03.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x4 Port 3 (rev 90) 0000:00:04.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x16 Port 4-7 (rev 90) 0000:00:05.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x4 Port 5 (rev 90)........

Dell CS10-F1D Server Info lspci Linux specs

0000:00:00.0 Host bridge: Intel Corporation 5000P Chipset Memory Controller Hub (rev b1) 0000:00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 (rev b1) 0000:00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 (rev b1) 0000:00:04.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 (rev b1) 0000:00:05.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4........

nf_conntrack: table full, dropping packet solution

nf_conntrack: table full, dropping packet The above in some cases I've seen is a sign of a DOS attack or can occur if users are using services like torrenting, proxy, VPNetc... Do not take it lightly as the above can knock a server offline if the table becomes full and I've also seen full crashes and kernel panics shortly after. ........

Dell CS24-NV7 Howto Enable LAN/NICs and PXEBoot in the BIOS

Dell CS24-NV7 Unusually the Virtualization was enabled when I got this server but all the NICs were diabled in the BIOS including PXE boot! Advanced -> Advanced Chipset Control PCI Slot 1 Option ROM: Enabled Onboard LAN1 Control: Enabled LAN1 Option ROM Scan: Enabled (you need it for PXE boot) Onboard LAN2 Control: Enabled LAN2 Option ROM Scan: Enabled *you will need to reboot and........

kvm centos cannot compile error

./configure ./configure: cannot locate gcc 3.x. please install it or specify with --qemu-cc yum -y install gcc make ./configure ./configure: cannot locate gcc 3.x. please install it or specify with --qemu-cc yum -y install compat-gcc-* ./configure Error: Could not find alsa Make sure to have the alsa libs and headers installed. yum -y install alsa-lib-devel ./configure........

CPanel suhosin install failed

/scripts/phpextensionmgr install PHPSuHosin Updating md5sum list Fetching http://httpupdate.cpanel.net/cpanelsync/easy/targz.yaml (connected:0).......(request attempt 1/12)...Resolving httpupdate.cpanel.net...(resolve attempt 1/65)... Fetching http://httpupdate.cpanel.net/mirror_addr_list (connected:0).......(request attempt 1/3)......connecting to 74.50.120.123...@74.50.120.123......connected......receiving...100%......request success......Done........

Dell FS12-NV7 2U Server Information and Guide

I've got one of these for testing projects from work at home and got more than I bargained for with the time I've spent on it due to the storage handing/Perc 6/i cards. My particular model came with the following: 2U Rack Mount Server with Rails 2xOpteron 2373 EE (Quad Core, there is a 6-core version that can be found at times) 16GB RAM 2 x 250GB Seagate SATA 2 x Dell Perc 6/i (horrible and a nightmare to work........

Dell Perc 6/i SATA benchmarks without battery

The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results. This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane. Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: N/A De........

LSI MegaRAID Adventures, Guide and HowTo

LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........

eth0 changed to eth1 or eth2 and the solution to fix it

If you move your hard drive(s) around to other computers/servers, you'll find that your eth0 keeps getting higher, the first time it will become eth1 and then eth2 etc and even higher if your server has dual or quad NICs. The reason is that udevd basically assigns eth0 tot he first NIC it finds and remembers it, if it encounters a NIC with a differentMAC, it assigns it one higher (eg. eth1). See the example below, I have eth2 now so how doI fix it?........

Linux/Debian shutdown/reboot without going through init force

-bash-3.1# shutdown -rn now Connection to localhost closed by remote host. Connection to localhost closed. Sometimes I work with embedded systems/custom kernels without any of the fancy init scripts and other common Linux basics that most would expect. This means that often the "reboot" command (which uses an init script) will never work, not only that but it will hang the server and a manual power cycle or reboo........

Samsung Galaxy Note I717M Canadian Version, Root and Unlock

I chose this because I heard a lot of stories about scams and that many providers I contacted said they can't unlock the Canadian I717s (one said "my Bell server" is down). This method worked perfectly on my Bell I717M and should work for all I717 in Canada, I was able to insert a foreign SIMcard. This will work abroad too but remember entering CWM mode is different for I717's in other countries (at least theUS). Step 1 - Root + CWM........

Samsung Galaxy Note ICS Corrupting microSDHC partition table?

This was partitioned as a single 32GB VFAT but when I inserted it into the phone it said that it can't read it and now here is how the partition table looks. Interestingly enough the data works and reads fine from the computer still. Disk /dev/sdb1: 32.1 GB, 32085360640 bytes 64 heads, 32 sectors/track, 30598 cylinders, total 62666720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum........

Samsung Galaxy Note Upgrade to ICS 4.0 microSDHC card not detected/dataloss after upgrading - possible solutions

I backed up everything in the /mnt/sd_card directory thinking that some dataloss could occur for some reason but purposely left my microSDHC unbacked up thinking that "it won't touch that since it's external" and Samsung's and other manufacturers website even say this (that it won't be affected and not to worry etc). Apparently I was wrong, my microSD was "undetected" and asked to be formatted after the upgrade (there goes 3-months worth of family photos). No........

Linux Ubuntu Nvidia GT430 Lockups/Errors/Freezes NVRM: os_schedule: Attempted to yield the CPU while in atomic or interrupt context

I'm running Ubuntu 10.10 with Asus NVIDIA GT430 2.6.35-32-generic-pae #65-Ubuntu SMP Tue Jan 24 14:06:16 UTC 2012 i686 GNU/Linux Nvidia binary driver: 260.19.06 The screen sometimes completely freezes and locks up or everything starts going very slow: [1903398.100007] NVRM: os_schedule: Attempted to yield the CPU while in atomic or interrupt context [1903402.373210] NVRM: Xid (0001:00): 53, CMDre 00000000 00000080 00000000 00000005 00........

Ubuntu 10 Nvidia Drivers Not Updated After Kernel Update Solution/How-To Manually Rebuild nvidia kernel modules for Ubuntu

I dread updating the kernel and rebooting to find the Ubuntu graphics aren't working and you have to manually intervene. This is usually because Ubuntu for whatever reason didn't update the drivers you need (eg. the manually compiled Nvidia Kernel driver that MUST be recompiled for each and every kernel update unfortunately). The most common reason may be that "linux-source" hasn't been installed automatically on my system. I tried to manually reinstall the........

2011 Best Laptop - HP 15.6" Laptop featuring AMD Athlon II P340 Processor (G62-420CA)

My mother needed a new laptop and I recommended her the same one I would have bought myself or my wife, that means the cheapest possible laptop with the most features for the money. This HP shines at this price point and one thing that made me stay away from buying more and recommending HP/Compaq was the poor battery life. Not anymore, this model has an industry leading up to 4 hours of battery life. Key Factors for Choosing It: HDMI Out........

Ubuntu 10.04 Linux is still not ready for the Desktop world

I am a huge fan of Linux and the idea of OpenSource but I've said it many times, there are still hurdles in today in 2010 for Linux as a Desktop. Linux is still intended for servers at its very core. This can be changed succesfully though, as Apple has shown us with Mac OS X based on FreeBSD. Half of the issue is lack of driver support and the other half is the Linux Kernel and Window Manages, KDE and GNome still both don't cut it (but they're getting closer). I'll........

jailkit for chroot ssh account security tutorial and fix for error

This was done on Centos butI think it's easier on Debian machines, the paths that it is set to use are tailored towards Debian, so there is some fiddling that needs to be done on Centos. This is for chrooting ssh, but jailkit has other uses than just SSH jails but I won't cover them in this writeup. 1. Install jailkit yum install jailkit 2. Setup Jail Home mkdir /home/jail chown root:root /home/ja........

Fix Slow 2D Graphics Xorg.conf Ubuntu/Debian/Mandriva Linux

I'm using Ubuntu 8.04 but anyone using older kernels will find this may apply to them. My Intel graphics are very slow with the default Xorg settings but by using "EXA" acceleration, scrolling down windows of text becomes pretty snappy. Just edit /etc/X11/xorg.conf Section "Device" Identifier "Configured Video Device" &nb........

cPanel complaint - No Shared SSL! cPanel 11.25.0-R46156 - WHM 11.25.0 - X 3.9

I've recently used CPanel on the admin side for the first time and have to say I hate it. Everything from the layout to the functionality screams "hackish". It just lacks so many common sense features and way of working. I was never 100% impressed with Plesk but the basics were definitely laid out and done in a sensible manner, even though it is made by a Russian company, they definitely thought about how to make a Control Panel. I have no idea why people........

Check How Many Watts Your CPU,HDD,GPU, Fans Use - Power Consumption Tool

www.antec.outervision.com/index.jsp I found that wattage/power consumption tool to be very useful, especially when you're worried that you're hitting the Power Supply's limit. You'll see very quickly that different CPU's, Graphics, Cards, HDDS use a wide range of energy. That tool can help you choose a build that won't stress or go over the maximum limits of your Power Supply.........

Compaq V2405CA Laptop - Unixbench Performance Test

Here are the results, it is Sempron 3000+ AMD Mobile, 500Gig HDD, 512MB RAM with shared ATI Radeon graphics. # # # # # # # ##### ###### # # #### # # # # ## # # # #&nb........

Linux Unix Xorg X Server Intel Extreme i810 Graphics Problem

Linux Unix Xorg X Server Intel Extreme i810 Graphics Problem(EE) I810(0): No Video BIOS modes for chosen depth. (EE) Screen(s) found, but none have a usable configuration. I have a new Dell PC with one of the latest Intel Extreme Graphics on-board crap. From what I can see any Linux/Unix/FreeBSD versions running XFree86 or Xorg from years ago or the latest version today will have this problem. It's easily corrected FOR MOST people. Go into your........

The New Chips on the Block

The New Chips on the BlockThe New Chips on the Block By Bruce Gain Story location: http://www.wired.com/news/infostructure/0,1377,67795,00.html 02:00 AM Jun. 13, 2005 PT We have embarked upon a new era in x86 PC computing -- so say chip giants AMD and Intel following their launches of dual-core PC processors. So how will dual-core processing change your PC computing experience? Our FAQ should help you decide whether or when you sho........

Tutorials on port upgrades

Tutorials on port upgradesnice to see a FreeBSD forum http://www.redantigua.com/portupgrade.html http://www.onlamp.com/pub/a/bsd/2003/08/28/FreeBSD_Basics.html?page=2........

PHPBB Drop All Tables

PHPBB Drop All TablesSQL Syntax: [quote:75acd496c1]drop table phpbb_auth_access, phpbb_banlist, phpbb_categories, phpbb_config, phpbb_confirm, phpbb_disallow, phpbb_forum_prune, phpbb_forums, phpbb_groups, phpbb_posts, phpbb_posts_text, phpbb_privmsgs, phpbb_privmsgs_text, phpbb_ranks, phpbb_search_results, phpbb_search_wordlist, phpbb_search_wordmatch, phpbb_sessions, phpbb_smilies, phpbb_themes, phpbb_themes_name, phpbb_topics, phpbb_topics_watch, phpbb_user_group, p........

RAID1 using Gmirror Tutorial

RAID1 using Gmirror Tutorialhttp://www.onlamp.com/pub/a/bsd/2005/11/10/FreeBSD_Basics.html........

CDR Manufacturers - Why is so much media bad?

CDR Manufacturers - Why is so much media bad?I have searched for good media and tried many kinds for years. I guess I'll try to summarize my findings and conclusions. Dye is irrelevant, dye of any color can be good or bad, it more likely depends on the manufacturer. Speaking of manufacturers, the name at the top of the disc means nothing. For example, Memorex along with any other 'brand' is actually always made by another manufaturer including CMC Mag........

Other Security Web Sites

Other Security Web SitesSeveral websites actively track security issues. This list provides you with the major providers of security information on the Web. Many of these organizations also provide newsletters and mailings to announce changes or security threats: Center for Education and Research in Information Assurance and Security (CERIAS) CERIAS is an industry-sponsored center at Purdue University that is focused on technology and relate........

Adventures in pre-paid SIM Cards and data GPRS/Edge/3G in China with China Mobile in Shenzhen, Guangzhou, Shanghai, Beijing and other cities

This really is a difficult and confusing process for non-Mandarin speakers, but here's what I've done and learned so far: You can purchase an "M-Zone" China Mobile pre-paid SIMCard from almost anywhere but I tried to purchase mine from Suning (a large electronics dealer) hoping they would be able to help me or answer my questions but my plan didn't work out at all. At Suning once I found someone who spoke some English they gave me the 55 RMB M-Zone China Mobile P........

Tyan S2735-8M motherboard/Rackable Systems 1u Server 100mbit NIC not working even when enabled in the BIOS

Itried everything Icould think of, and of course even with the NIC enabled in the BIOS nothing was working. The light would flash when you plugin the cable for a second, but that's all. Due to another issue I'm about to post about (server is not compatible with 1TB/1000Gig Hard Drives), I updated the BIOS. I didn't even know the 100mbit NICs were not working untilI decided I should test each NIC one by one. Inoticed that only 1 server out of........

iPhone/iPod touch on 3.0 software overheating?

There have been lots of reports like this going around and Ican confirm my 3GS with 3.0 firmware is overheating as well. It gets quite hot and actually can make your head or hand sweaty when holding it to talk, or simply holding the back cover for any reason. It's a wonder how the device cools itself at all, considering the only thing that could ventilate air are the 2 speakers at the bottom or the single speaker on the front of the device. Apple seems to be making........

iPhone 3GS 32GB "Harsh Review"

Yes, Iadmit I finally got bitten by the hype as much as I can usually see through it all. Keep in mind this review is of the "stock" phone, no jailbreaking yet which is what really unleashes the customizability and whyI bought iPhone. I had better things to say about this phone before buying it, and it is a great phone, perhaps the best on the market by far, if not because of the Mac OS port onto the iPhone and all the apps, etc, etc. With that said........

iPhone Safari Browser and TinyMCE Support

This is unfortunate and frustrating as many sites use it, a lot of people are frustrated that TinyMCE does not work on the iPhone Safari browser. Apparently the developer of TinyMCE's answer is "talk to Apple about it" It's really frustrating although, I wonder if any other mobile phones are able to use TinyMCE or not, whatever the case is it would be nice to find a solution to use TinyMCE on the........

Apple iPhone 3GS and predecessors are leading a revolution

As much of a computer nerd as Iam, I'm usually a late adopter to technology for a few reasons. Ifeel most new hyped technologies and electronics are mainly fads, and I'm also cheap. Adopting later means you avoid the bugs, kinks and most importantly pay the lowest price, that's me being cheap again :) I never read much about the iPhone but Isaw all the hype around it and until recently I wasn't a big fan of anything Apple until a few years ago I realize........

Nokia N97 review, feedback and complaints

I've had an old Blackberry for a few years and I was ready to spend some serious cash on a nice Nokia. I love the idea of the Linux based Symbian S60 OS, so I was looking at phones like the E63, E71 (both are basically the same, at least CPU/screensize although E71 is thinner, has a 3MP camera, has GPS, and has dedicated buttons to adjust the volume). Then Iheard about the N97 and what a revolution it was supposed to be and it was even compared to iPhone. To........

RTL8111/8168B R8169 Gigabit Link slow speeds

This is the Intel Atom 330 motherboard with integrated Realtek Gigabit NIC (Intel Desktop Board D945GCLF2 Motherboard W/ Atom 330 1.6 GHz Dual Core Processor - Mini-ITX) I cannot achieve more than 15 MB/s, even doing a local transfer through eth0 to it's own IP. 100% 95MB 15.9MB/s 00:06 So this is not a cabling, switch or hardware issue, it seems like a driver or chipset limitation problem. Here is my........