• Using Cisco CME Router with Asterisk as a dial-peer


    #Remember that you need a valid gateway IPunless the Asterisk server is on the same subnet and LAN Set Valid Gateway IP (if you don't have one already) ip route 0.0.0.0 0.0.0.0 GATEWAYIP Enable VOIPTrust voice service voip ip address trusted list ipv4 0.0.0.0 0.0.0.0 sip Set Credentials For Asterisk and Register To Asterisk sip-ua........
  • Cisco CME How To Configure SIP Trunk VOIP


    This is how we configure outside PSTNaccess or dialing through another SIPtrunk. Beware that this a simplistic example that neglects most security including SRTP First you'll need to be in config mode: Step - 1 Enter Voice Service VOIP security options There are more options but for now we'll just focus on security/allowing connections to and from our phones and the trunk. Router(config)#voice service voip ........
  • Cisco CME and C7200 Router Testing and Learning Environment on Ubuntu 20+ Setup Tutorial Guide


    Since newer versions of Ubuntu like 20, you will find there is no longer dynagen and that the dynamips provided is faulty and will segfault each time: Cisco Router Simulation Platform (version 0.2.14-amd64/Linux stable) Copyright (c) 2005-2011 Christophe Fillot. Build date: Apr 3 2018 12:20:29 Local UUID: 3c1c0b7f-2fab-4fda-b40b-74841d1bcfe0 Instance ID set to 1. netio_tap_create: unable to open TAP device tap1 (No such fi........
  • CentOS 7 fix Could not retrieve mirrorlist http://mirrorlist.centos.org/?release=7&arch=x86_64&repo=os&infra=container error was 14: curl#6 -


    yum update Loaded plugins: fastestmirror, ovl Determining fastest mirrors Could not retrieve mirrorlist http://mirrorlist.centos.org/?release=7&arch=x86_64&repo=os&infra=container error was 14: curl#6 - "Could not resolve host: mirrorlist.centos.org; Unknown error" One of the configured repositories failed (Unknown), and yum doesn't have enough cached data to continue. At this point the onl........
  • How to configure OpenDKIM on Linux with Postfix and setup bind zonefile


    This guide assumes you have a working Postfix server and want it to sign with DKIM. There are a few things we have to understand to make all of this work though, which require you to be familiar with DNS as well. 1.) Install OpenDKIM apt install opendkim systemctl enable opendkim 2.) Edit /etc/opendkim.conf Syslog yes SyslogSuccess yes Mode&nbs........
  • Apache Error Won't start SSL Cert Issue Solution Unable to configure verify locations for client authentication SSL Library Error: 151441510 error:0906D066:PEM routines:PEM_read_bio:bad end line SSL Library Error: 185090057 error:0B084009:x509 certif


    [Wed Nov 01 18:47:08 2023] [error] Unable to configure verify locations for client authentication [Wed Nov 01 18:47:08 2023] [error] SSL Library Error: 151441510 error:0906D066:PEM routines:PEM_read_bio:bad end line [Wed Nov 01 18:47:08 2023] [error] SSL Library Error: 185090057 error:0B084009:x509 certificate routines:X509_load_cert_crl_file:PEM lib It actually gives us a good clue that at last one component of our cert is invalid/improperl........
  • REFUSED unexpected RCODE resolving bind/named error


    Are you getting this error when trying to connect to a site/domain/service and then you checked your router/nameserver's logs to see what's wrong? You may see something like this: named[3025898]: REFUSED unexpected RCODE resolving This is not usually an error with named or bind, at least not on your end but NORMALLY this is an issue with the remote nameserver. A lot of times this is a misconfigured remote nameserver. A classi........
  • Docker Swarm vs Kubernetes Comparison Guide


    A lot of companies are unsure which solution to choose and many may not be aware of Docker Swarm as an alternative to Kubernetes. One thing that many Sysadmins find is that Docker Swarm is simply easier, quicker to setup and maintain by far than Kubernetes.........
  • configure.ac:75: error: possibly undefined macro: AC_PROG_LIBTOOL If this token and others are legitimate, please use m4_pattern_allow. See the Autoconf documentation. solution


    configure.ac:75: error: possibly undefined macro: AC_PROG_LIBTOOL If this token and others are legitimate, please use m4_pattern_allow. See the Autoconf documentation. autoreconf: /usr/bin/autoconf failed with exit status: 1 make: *** [/software/pixman/configure] Error 1 make: *** Deleting file `/software/pixman/configure' yum install libtool........
  • Can't exec "aclocal": No such file or directory at /usr/share/autoconf/Autom4te/FileUtils.pm line 326. autoreconf: failed to run aclocal: No such file or directory solution


    autoreconf: Entering directory `.' autoreconf: configure.ac: not using Gettext autoreconf: running: aclocal --output=aclocal.m4t Can't exec "aclocal": No such file or directory at /usr/share/autoconf/Autom4te/FileUtils.pm line 326. autoreconf: failed to run aclocal: No such file or directory make: *** [/software/pixman/configure] Error 1 Just install automake: yum install automake........
  • glib-2.0 required to compile QEMU solution


    ./configure glib-2.0 required to compile QEMU yum install glib2 glib2-devel or on Debian/Ubuntu based: apt install libglib2 libglib2-dev........
  • How To Upgrade Debian 8,9,10 to Debian 12 Bookworm


    Step 1.) Upgrade to Debian 11 first The process to go to Debian 12 is not as smooth as 11, when trying to upgrade from Debian 10. In fact, it doesn't work directly, so you'll first need to follow this guide to update to Debian 11, reboot and come back here if successful. Step 2.) Update sources.list Update your /etc/apt/sources.list like this: deb http://........
  • apache2 httpd apache server will not start [pid 22449:tid 139972160445760] AH00052: child pid 23248 exit signal Aborted (6) solution Mint Debian Ubuntu Redhat


    If you get this error, it is often because you have configured Apache with modules that weren't actually installed. Eg. you try to load the PHPmodule but didn't actually install the apache2 php module, so the server can't start. In general, this error can often be caused by issues with problematic modules and/or Apache being configured for modules that have not actually be installed (eg. libapache2-mod-php) is missing. The above results in this less than obv........
  • How to Configure NVIDIA GPUs with Docker on Ubuntu: A Comprehensive Guide for AI Deep Learning CUDA Solution


    Welcome to our in-depth guide on configuring NVIDIA GPUs with Docker on Ubuntu. This post is tailored for developers, data scientists, and IT professionals who are looking to leverage the power of NVIDIA's GPU acceleration within Docker containers. Whether you're working on machine lea........
  • Linux Ubuntu Mint how to check nameservers when /etc/resolv.conf disabled solution


    You'll notice that /etc/resolv.conf contains dire warners on most Linux Desktops. # This file is managed by man:systemd-resolved(8). Do not edit. # # This is a dynamic resolv.conf file for connecting local clients to the # internal DNS stub resolver of systemd-resolved. This file lists all # configured search domains. # # Run "resolvectl status" to see details about the uplink DNS servers # currently in use........
  • Could not read response to hello message from hook [ ! -f /usr/bin/snap ] || /usr/bin/snap advise-snap --from-apt 2>/dev/null || true: Connection reset by peer


    You may have a broken apt configure that calls for snap (which is not installed if you get the error below): apt install coreutils Reading state information... Done E: Could not read response to hello message from hook [ ! -f /usr/bin/snap ] || /usr/bin/snap advise-snap --from-apt 2>/dev/null || true: Connection reset by peer E: Could not read message separator line after handshake from [ ! -f /usr/bin/snap ] || /usr/bin/snap advi........
  • How to install and configure haproxy on Linux Ubuntu Debian


    haproxy is one of the best known and widely used Open Source load balancers out there and a strong competitor to nginx. haproxy is used by many large sites per Wikipedia: HAProxy is used by a number of high-profile websites including GoDaddy, GitHub,........
  • talib/_ta_lib.c:747:10: fatal error: ta-lib/ta_defs.h: No such file or directory


    If you are installing ta-lib for Python and get this error then you can normally solve it by manually getting the ta-lib source files and compiling. tar -zxvf ta-lib-0.4.0-src.tar.gz cd ta-lib;./configure;make;make install Collecting ta-lib Downloading https://files.pythonhosted.org/packages/39/6f/6acaee2eac6afb2cc6a2adcb294080577f9983fbd2726395b9047c4e13ec/TA-Lib-0.4.26.tar.gz (272kB) &nbs........
  • VboxManage VirtualBox NAT Network Issues Managment Troubleshooting


    If you find your NAT Network is not working properly, the first thing you may want to do is list the networks, check their status and make sure the Network is actually started and configured as you expect (eg. is DHCP on and enabled?). This is a long known, unresolved bug that seems to affect Version 6 randomly and disportionately on especially Mint 20/Ubuntu 18. https://www.virtualbox.org/ticket/1474........
  • Cisco Switch / Router How To Restore Factory Default Settings


    1.) Make sure your conf register is 0x2102 Do show version and at the very end of the output you will see the Configuration register. show version Configuration register is 0x2102 If the config register is not 0x2102 then enter this command: r1#configure terminal r1(config)#config-register 0x2102 r1(config)#end 2.) Let's Erase the NVRAM/flash........
  • Cisco 2900 3900 Router Password Reset How To Reset Enable Password


    It is a bit different and annoying here for these types of routers/models as you need to physically remove the CF (Compact Flash) and only then, will it enter ROMMON mode (Ctrl + Pause remotely over the console will not do it for us). This means you cannot do this remotely, or at least not without the help of a remote/physical helper. Step 1.) Power off, router and remove CF Disk Slot#2 Go to the router and remove the slot#2 cover uses your hand or it may help to use a........
  • RTL8821AU Setup Configure Wifi Realtek 8821 in Linux Debian Mint Ubuntu Howto


    The easiest way for the 8821AU Realtek Wifi chipset / TP-Link T2U Plus: Bus 002 Device 003: ID 2357:0120 TP-Link Archer T2U PLUS [RTL8821AU] First install your kernel headers/source/other required tools: sudo apt install linux-headers-`uname -r` make gcc bc Clone this github repo with the driver: git clone https://github.com/morrownr/8821au-20210708 Run the compile/ins........
  • ssh Too many authentication failures not prompting for password


    If you get this error when trying to SSHto a device or machine and you never even got a password prompt: Too many authentication failures This means that either the remote side is configured for key auth only, OR your client side may be attempting to auth using mulitple keys, and that exceeds the amount of attempted authorizations on the remote ssh server. If the issue is trying to auth too many times which ssh defaults to sending the keys to, you ca........
  • How To Do Linux Network Bonding Teaming in Mint Debian Ubuntu


    Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........
  • LXC Containers LXD How to Install and Configure Tutorial Ubuntu Debian Mint


    If you are using mint, delete the preference that stops snap from installing (as it is required for lxc) sudo rm /etc/apt/preferences.d/nosnap.pref 1. Install lxd: sudo apt install lxd Issues install lxd or errors? Click here Debian at this time does not have lxd so you'll need to use snap: sudo apt in........
  • Docker Tutorial HowTo Install Docker, Use and Create Docker Container Images Clustering Swarm Mode Monitoring Service Hosting Provider


    The Best Docker Tutorial for Beginners We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........
  • How To Create OpenVPN Server for Secure Remote Corporate Access in Linux Debian/Mint/Ubuntu with client public key authentication


    Why choose OpenVPN instead of a firewall appliance? OpenVPN can be a reliable and easy replacement for traditional hardware or just be an additional tool that your company uses so that the firewall can focus on its job rather than acting as a VPNappliance at the same time. When comparing OpenVPN with traditional firewal........
  • tag#4 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE tag#4 Sense Key : Illegal Request [current] res 40/00:b4:98:02:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) solution


    You might assume you have a bad drive or the SATA interface/cable is bad, or the power supply is bad/weak to the drive. These are all possible issues, but definitely check your SATA cable for "twisting". It is a big issue because until the error stops or times out, your system will not boot (in my case this was the case even though the drive with the issue was not part of the OS or booting process at all). If you run an open rig that you move around often that ha........
  • Wazuh / OSSEC Install and Configuration Howto Tutorial Guide for Monitoring Agents SIEM


    How To Install Wazuh Server / Quickest Installation Wazuh (forked from the well known OSSEC project) is a full SIEM (Security Information Event Management) that works extremely well with the platforms it natively supports as an "Agent", which allows you to do scans of everything such as all processes running, CVE vulnerability check, incident reporting etc... Prerequisites: A lot of issues with Wazuh seem to be caused by i........
  • Ansible Tutorial - Playbook How To Install From Scratch and Deploy LAMP + Wordpress on Remote Server


    1. Let's work from an environment where we can install Ansible on. If you are using an older version of Linux based on Mint 18 or Ubuntu 16, you may want to get the PPA and get the latest version of Ansible that way: sudo apt install gpg sudo add-apt-repository ppa:ansible/ansible sudo apt update........
  • Cisco Howto Configure Console Port/Terminal/Comm Server with Async Cable Setup


    This assumes that you've already installed the relevant HWIC cards eg. Cisco Asynchronous Serial NIM These are essentially cards that you install into your router, once installed you connect an Async cable to one of the ports on the card which normally gives you 8 console cables and are normally labelled 1 through 8. You connect all of the cables to the devices you need (even non-Cisco devices) whether switches, routers or firewalls, they will usually work. The real m........
  • Unable to mount location Failed to retrieve share list from server: Connection timed out - Samba/Linux Filesharing Not working Ubuntu Mint Linux Solution


    So you're trying to browse to a properly configured Samba share but you get this error: Unable to mount location Failed to retrieve share list from server: Connection timed out If your config is right, it can be due to a protocol miss-match where your client has not enabled SMB3 but by default the other side (server) has enabled it. You can test this out to see with the smbclient tool........
  • EFI PXE grub2 Howto guide for Linux EFI PXE Booting on Debian, Mint, Ubuntu, RHEL


    Just a quick note and warning is that if you are testing to see if EFIPXE booting works on a VM, MAKE SURE it actually works. For example Iinitially tested using my Distro's QEMU 2.5+dfsg-5ubuntu10.46 and ovmf BIOS firmware (OVMF supports EFI). However, I found on old versions of QEMU (like 2.5), EFIbooting with GRUB NEVER works so it may appear that you have made a mistake when everything is fine when you boot a physi........
  • Juniper JunOS Command Overview and Howtos Switch, Router, Firewall Tutorial Guide


    Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........
  • Linux how to compile binary with static sharedobjects embedded instead of dynamic to use on multi-distributions and avoid glibc compatiblity issues


    One simple flag to configure will create a makefile that statically links all the shared objects and embeds them instead the binary execute. This means as long as you have the same architecture that things should run. Eg. if you have an old version of Debian with a different version of glibc, then this will solve that problem. ./configure LDFLAGS="-static" To test that it is really statically linked run ldd: ldd src/wget........
  • /bin/sh: msgfmt: not found error solution on Linux Compilation Ubuntu Debian Mint Centos


    If you get this error, you were probably compiling some sort of binary or package and got this error. It is normally solved by installing the "gettext"package. On Debian/Ubuntu just apt-get it: apt-get install gettext After that you should be able to configure and make (compile) properly.........
  • qemu 4 compilation options


    How To Compile QEMU Manually (using sensible options) 1.) Download the QEMU source file you want. wget https://download.qemu.org/qemu-4.2.0.tar.xz 2.) Extract The Source File tar -Jxvf qemu-4.2.0.tar.xz 3.) Switch to the extracted source cd qemu-4.2.0 4.) Make sure we have the right libraries and tools to compile QEMU manually sudo apt install build-e........
  • apcupsd how to setup and monitor APC UPS units


    It really seems limited in that it can mainly give you the things you would see on the physical unit such as load etc.. wget https://downloads.sourceforge.net/project/apcupsd/apcupsd%20-%20Stable/3.14.14/apcupsd-3.14.14.tar.gz?r=https%3A%2F%2Fsourceforge.net%2Fprojects%2Fapcupsd%2Ffiles%2Flatest%2Fdownload&ts=1598115866 tar -zxvf apcupsd-3.14.14.tar.gz cd apcupsd-3.14.14 [root@somebox apcupsd-3.14.14]# ./conf........
  • CentOS 6 impossible to compile a newer libguestfs


    yum -y install gcc make gperf genisoimage flex bison ncurses ncurses-devel pcre-devel augeas-devel augeas readline-devel checking for cpio... cpio checking for gperf... no configure: error: gperf must be installed configure: error: Package requirements (augeas >= 1.2.0) were not met: Requested 'augeas >= 1.2.0' but version of augeas is 1.0.0 yum remove augeas augeas-libs augeas-devel wget http://downl........
  • How To Get Started on Ubuntu with gpt-2 OpenAI Text Prediction


    apt install software-properties-common add-apt-repository ppa:deadsnakes/ppa apt update apt install python3-pip apt install python3.7 curl gnupg python3.7-dev git ln -s /usr/bin/python3.7 /usr/bin/python3 pip3 install numpy keras_preprocessing curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add - echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........
  • Linux How To Change NIC Name to eth0 instead of enps33 or enp0s25


    Most newer distros inexplicably cause your NIC to have what Icall "random" non-standard name conventions because of systemd. This is a big problem for many people and especially those running servers. Imagine that you have a static IPconfigured for ens33 but then the hard disk is moved to a newer system, the NIC could be anything from ens33 to enp0s1, meaning that manual intervention is required to go and update the NIC config file (eg. /etc/network/interfa........
  • How To Install OpenProject on Centos 7 Step-by-Step Guide


    There are a few caveats that may not be obvious to everyone so I am going to cover them here but keep this in mind before starting. Before starting install epel or you will be missing tesseract: yum -y install epel-release #1) When you specify your SSL certificate with a full path, it really needs to exist where you tell it to (including the default location of /etc/ssl/certs and /etc/ssl/c........
  • How To Install python 3.4 3.5 and up on Linux with wine - Working Solution


    This is sure simple if you follow the guide but it took a lot of hacking around to make this work on Debian/Ubuntu! Now before you ask why bother running wine and python, the reason is because Python executables are NOT cross-platform. If you run pyinstaller in Linux, that binary will only run on Linux and the same if you do it in Windows. So it is preferable if you have a single environment that you can create Linux and Windows binaries from rather than running 2 separate........
  • using Xvfb on virtual remote ssh server to have X graphical programs work


    The scenario here is that you have some sort of remote headless Linux server but would like to run some programs on them and get graphical access to them. The problem is that the remote server may be an image or VMwithout any virtual GPU and even if so, it is likely without KDE or Gnome, so there's no real way to do this, unless you follow our guide. Install xvfb apt install xvfb Reading package lists... D........
  • MySQL 5.7 on Debian and Ubuntu - How To Reset Root Password


    MySQL on Debian versions is configured differently than the native local MySQL plugin so you will be disappointed when your password on the mysql client fails by default. Here is how you reset the MySQL root password the proper and "working way" #first we gracefully stop mysql sudo systemctl stop mysql; #then we forcefully kill any mysqld process just in case sudo killall -9 mysqld mysqld_safe;........
  • CentOS 8 how to convert to a bootable mdadm RAID software array


    The cool thing here is that we only need 1 drive to make a RAID 10 or RAID 1 array, we just tell the Linux mdadm utility that the other drive is "missing" and we can then add our original drive to the array after booting into our new RAID array. Step#1 Install tools we need yum -y install mdadm rsync Step #2 Create your partitions on the drive that will be our RAID array Here I assume it is /dev........
  • how to use ifplugd in Linux to execute a command or script when a NIC cable is unplugged or plugged in


    It is fairly simple to use once you know how to use it. However, the tricky thing is that by default it doesn't seem to be active or listen on any interface on manually specified. How To Install ifplugd First we install ifplugd sudo apt install ifplugd Let's enable it on our desired device(s) vi /etc/default/ifplugd set this line as so:........
  • How To Install Asterisk 16 17 on Debian Ubuntu Linux


    Downloading and compiling from source to get the latest version of Asterisk is really simple with this guide. apt install gcc make g++ libedit-dev uuid-dev libjansson-dev apt install libxml2-dev sqlite3 libsqlite3-dev wget http://downloads.asterisk.org/pub/telephony/asterisk/asterisk-16-current.tar.gz tar -zxvf asterisk-16-current.tar.gz cd asterisk-16.6.2/ ./configure If you get this error change y........
  • Cisco Unified Communications Manager / CUCM IP 8.6,10,12 Install Error Solution


    Install Errors on Version 12: This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5 on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error. *Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install. What really causes this even though you successfully install........
  • Cisco DHCP Snooping Relay Setup Information


    Switch#show ip dhcp snooping Switch DHCP snooping is disabled DHCP snooping is configured on following VLANs: 1 Insertion of option 82 is enabled circuit-id format: vlan-mod-port remote-id format: MAC Option 82 on untrusted port is not allowed Verification of hwaddr field is enabled Interface&nb........
  • Cisco Switch Setup Guide Command List


    Enter configuration console: enable configure terminal This is important because if your console doesn't look like below none of the commands will work! Switch(config)# Save and Apply Settings wr Show Switch Configuration: show run Show Port List/Sta........
  • iSCSI on Centos 7 Configuration and Setup Guide for Initiator and Target


    initiator = client target = server These are the first concepts you should understand which is that in iscsi essentially the "initiator" is the client and the "target" is the server. iSCSI is derived from the old fashioned SCSI that us oldtimers grew to love. The "i" stands for Internet and the SCSI stands for "Small Computers Systems Interface" (SCSI). iSCSI Target (Server)Setup targetcli is the pac........
  • How Does Cisco CUCM (Cisco Unified Communication Manager) Work?


    Cisco's CUCM (Cisco Unified Communication Manager) is a system that combines voice, video, data and mobile products into a single unified management suite. At its core, the CUCMis like a "Super PBX" that controls the flow of all communications through an organization even single or multiple site deployments. Cisco's CUCMmakes communication more effective and simple through centralized management and unification of communications resources.........
  • MySQL Using mytop Debug Source of High IO and Slow Performance


    mytop is one of my favorite tools and it is fairly simple aside from a few caveats and issues that persist to this day. To install it on Centos: yum -y install centos Configure ~/.mytop vi ~/.mytop user=root host=localhost db=test #port=3306 socket=/var/lib/mysql/mysql.sock header=1 color=1 Try runni........
  • systemd management using systemctl and journalctl to check systemd logs


    systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system. The key commands or arguments you will use with systemctl are the following: Unit Commands: list-units [PATTERN...] List loaded units &nbs........
  • PHP Displaying Blank Page on Apache


    Almost always the reason will be that the php.so file is missing but also that php.conf is misconfigured. In the problem machine it is actually PHP7 installed so if you reference PHP5 of course things wil be broken! Take for example here: cat /etc/httpd/conf.d/php.conf # # PHP is an HTML-embedded scripting language which attempts to make it # easy for developers to write dynamica........
  • VMWare Hardware virtualization is selected and cannot be deselected due to selection of VBS Insufficient resources to satisfy configured failover level for vSphere HA.


    There is no such option as "VBS" that Ican see in vSphere 6.7 Ibelieve this is actually an issue because of using old hardware in this case L5420 doesn't support Nested Virtualization I believe. Hardware virtualization is selected and cannot be deselected due to selection of VBS Insufficient resources to satisfy configured failover level for vSphere HA.........
  • *** These critical programs are missing or too old: gawk


    checking whether autoconf works... ../configure: line 5377: 7325 Segmentation fault $AUTOCONF $ACFLAGS configure.in > /dev/null 2>&1 no configure: error: *** These critical programs are missing or too old: gawk *** Check the INSTALL file for required versions. ........
  • Centos 7 - How To Install NFS and Mount Remotely


    Server Side Config 1.) First install nfs-utils yum -y install nfs-utils 2.) Configure nfs share Create a directory for your NFS share mkdir /datastore Create your NFS share in /etc/exports echo "/datastore 10.220.101.0/24(rw,sync,no_root_squash)" >> /etc/exports systemctl restart nfs........
  • VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI


    #mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........
  • Cannot create gradle for conversations


    The main issue is it looks like Java is not configured to accept the invalid ssl cert that is coming from the download location. Exception in thread "main" java.lang.RuntimeException: javax.net.ssl.SSLException: java.security.ProviderException: java.security.InvalidKeyException: EC parameters error export ANDROID_HOME=/home/user/Downloads/tools/ Conversations-master$ ./gradlew Downloading https://services.gradle.org/distributions/grad........
  • Maximum number of connections from user+IP exceeded (mail_max_userip_connections=10) Dovecot Solution


    This happens because Dovecot limits the maximum IMAPconnections per IPto just 10. This may be fine for a single client side IPbut if an entire office or multiple users are behind one IPor a single heavy user is active then you will get bizarre errors in your e-mail clients such as "Password Incorrect" or similar in Thunderbird. It won't be obvious on the client side as to what the problem is and they will probably just think the server is misconfi........
  • Linux Mint Black Screen after boot no graphics solution


    This is not the normal "black screen"issue and I was shocked to eventually find out why. The normal advice of reconfiguring Xorg didn't work. Even booting into "Recovery Mode" did not help. Here is the short end of the stick that fixed it: sudo apt-get install mdm mate-desktop-environment Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled. This must be whe........
  • IcedTea Java Web Viewer Config Utility How To Enter


    In at least Ubuntu and Mint there is nothing intuitive about configuring Java. Execute it to get to it: itweb-settings You'll be able to configure different options and variables. You can also check under Security as some of those settings could prevent applets from starting or prompting to........
  • Centos How To Update to Glibc 2.14 Plus


    Centos 6 requires GLIBC 2.12 however a lot of new programs you would want to compile may need a newer glibc. You can't remove the old glibc since the whole OS is based on it but you can install the updated glibc alongside it and do an export pointing to your updated GLIBC. mkdir ~/glibc_install; cd ~/glibc_install wget http://ftp.gnu.org/gnu/glibc/glibc-2.14.tar.gz........
  • GCC 5 on Centos 6 - How To Install


    Install requirements: yum -y install gmp-devel mpfr-devel libmpc-devel glibc-devel glibc-devel.i686 zip unzip jar Download, untar, configure, compile and install GCC http://mirrors.kernel.org/gnu/gcc/gcc-5.5.0/gcc-5.5.0.tar.gz tar -zxvf gcc-5.5.0.tar.gz cd gcc-5.5.0 ./configure make make install Now you need to cleanup th........
  • ffmpeg Linux Mint download, compile and install howto


    #if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2 tar -jxvf ffmpeg-3.3.2.tar.bz2 cd ffmpeg-3.3.2/ ./configure --disable-yasm install prefix /usr/local source path ........
  • Centos 7 Cudaminer Nvidia setup guide


    I am using a GTX 1060 but replace the download for the driver with the correct/current version for your particular card by visiting: http://www.nvidia.com/Download/index.aspx?lang=en-us yum install automake curl openssl-devel libcurl-devel gcc gcc-c++ yum -y install kernel-devel-`uname -r` yum -y install unzip #the........
  • Linux Mint Install Netboot PXE Guide Howto


    *Update so this doesn't work it must be something to do with the path of nfs or something else but the installer fails with "Installer crashed" at the end whereas with the CD/USB it works. This assumes you've already installed and configured a separate PXE/DHCP server somewhere else and your /tftpboot directory is setup. This is for Linux Mint 18.1 but generally applies to most versions although you may have tro change things like "casper"........
  • ERROR 2013 (HY000): Lost connection to MySQL server during query


    The solution is simple but strange, if you copy your /var/lib/mysql directory to another server and think it will work, be sure to check if you have /var/log/mysql and binary log files. If you do, the server will not work and will give you errors like below and crash without the proper log files. UPDATE user SET password=password("newpass") WHERE user='root'; flush privileges; ERROR 2013 (HY000): Lost connection to MySQL server durin........
  • /dev/drbd0: State change failed: (-2) Need access to UpToDate data solution


    Everytime I've seen this error "/dev/drbd0: State change failed: (-2) Need access to UpToDate data" it is because DRBD has no disk: cat /proc/drbd version: 8.3.13 (api:88/proto:86-96) GIT-hash: 83ca112086600faacab2f157bc5a9324f7bd7f77 build by root@sighted, 2012-10-09 12:47:51 0: cs:Connected ro:Secondary/Secondary ds:Diskless/Inconsistent A r----- ns:0 nr:0 dw:0 dr:0 al........
  • Nvidia Linux Card not working due to LSI 9200/SAS2008 IRQ conflict


    At first my BIOS said the card may not work right because there is no more option ROM space. I disabled the Option ROM for both LSI 1068 and 2008 chipsets, Network Boot ROM and most other PCI slots, Serial Port, etc... and the message went away but the card still does not work properly. But it still cannot initialize the card properly(does not work): [ 33.943272] NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:........
  • status: { DRDY ERR } error: { ICRC ABRT } failed command: WRITE FPDMA QUEUED MCP55 Linux Errors


    [ 2868.041375] ata1: EH in SWNCQ mode,QC:qc_active 0x40 sactive 0x40 [ 2868.041554] ata1: SWNCQ:qc_active 0x40 defer_bits 0x0 last_issue_tag 0x6 [ 2868.041556] dhfis 0x40 dmafis 0x40 sdbfis 0x20 [ 2868.041874] ata1: ATA_REG 0x41 ERR_REG 0x84 [ 2868.042013] ata1: tag : dhfis dmafis sdbfis sactive [ 2868.042163] ata1: tag 0x6: 1 1 0 1 [ 2868.042301] ata1.00: exception Emask 0x1 SAct 0x40 SErr 0x400000 action 0x6 frozen [........
  • Unable to configure RSA server private key SSL Library Error: 185073780 error:0B080074:x509 certificate routines:X509_check_private_key:key values mismatch


    [Tue Jun 23 02:05:52 2015] [error] Unable to configure RSA server private key [Tue Jun 23 02:05:52 2015] [error] SSL Library Error: 185073780 error:0B080074:x509 certificate routines:X509_check_private_key:key values mismatch The above is an accurate description of what is wrong. In our case the client made a simple mistake of thinking the localhost.crt and localhost.key (default key locations for Apache SSL in Centos) were in the same directory but they we........
  • Disable linux bash proxy ENV export variable


    if you type Export and see something like this: declare -x all_proxy="socks://127.0.0.1:22000/" Most sites assume and tell you to check your .bashrc or /etc/profile /etc/bash.bashrc which may not apply if you've unknowingly or forgot that you setup a proxy from your GUI such as Gnome. To check in Gnome if you have a permanent proxy do the following: System -> Settings -> Network Proxy........
  • bash shellshock how to manually patch when there is no update for Centos/Debian/Ubuntu/Fedora


    wget http://ftp.gnu.org/gnu/bash/bash-4.3.tar.gz tar xzvf bash-4.3.tar.gz cd bash-4.3/ wget --no-directories --level 1 --recursive http://ftp.gnu.org/gnu/bash/bash-4.3-patches/ for patch in `ls bash43-*|grep -v .sig$`; do echo applying "$patch" patch -p0 < $patch done ./configure;make;make install #it will install to /usr/bin/bash but if your bash is somewhere else you need to overwrite the old one.........
  • Postfix how to secure outgoing authenticated e-mails for privacy and hide the IP address, mailer and other things


    The most common solution is to use the /etc/postfix/header_checks but this is a big problem. Why is header_checks a problem? Because it does it to all mail whether incoming or outgoing and whether authenticated or not. We of course want as much header information for incoming as we can get for many reasons but many organizations want to secure and make their mail clients as secure as possible. I adapted this solution to the client's custom config, they are configur........
  • CPanel Link to all of the command line options


    CPanel says you can access 98% of the functions through CLI which experienced Unix/Linux admins prefer for simplicity and for scripting.  I've never found CPanel easy to use from the admin panel, it seems everything is hard to find and a simple task becomes a series of hunts. So for people like me here's the list: http://cpanel.net/system-administrators/command-line-scrip........
  • How to Enable RDP Remote Desktop in Windows 2008 Server


    Start -> Administrative Tools ->Server Manager Under "Computer Information" click "Configure Remote Desktop". Under "System Properties" choose the type of "Allow connections" you want. That's all there is to enabling RDP Access in 2008 server.........
  • OpenVZ mismatched kernel and dev when compiling.


    ./configure ./configure: line 91: cd: /lib/modules/2.6.32-042stab084.25/build: No such file or directory Error: kernel version not found. Please make sure your kernel is configured. dr-xr-xr-x. 4 root root 4096 Feb 21 06:13 .. lrwxrwxrwx 1 root root 45 Feb 21 06:13 build -> ../../../usr/src/kernels/2.6.32-042stab084.25 drwxr-xr-x 2 root root 4096 Feb 12 20........
  • What a hdd hard drive and mdadm RAID array failure looks like in Linux


    [3805108.257042] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [3805108.257052] sd 0:0:0:0: [sda] Write Protect is off [3805108.257054] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [3805108.257066] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [3805108.257083] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [3805108.257090] sd 0:0:0:0: [sda] Write Protect is off........
  • Linux Bash grep howto find line number that contains the result


    cat Xorginfo.txt|grep -nr "xserver-xorg" Result: 9: sudo apt-get remove --purge xserver-xorg 13: sudo apt-get install xserver-xorg 17: sudo dpkg-reconfigure xserver-xorg........
  • kvm centos cannot compile error


    ./configure ./configure: cannot locate gcc 3.x. please install it or specify with --qemu-cc yum -y install gcc make ./configure ./configure: cannot locate gcc 3.x. please install it or specify with --qemu-cc yum -y install compat-gcc-* ./configure Error: Could not find alsa Make sure to have the alsa libs and headers installed. yum -y install alsa-lib-devel ./configure........
  • CPanel suhosin install failed


    /scripts/phpextensionmgr install PHPSuHosin Updating md5sum list Fetching http://httpupdate.cpanel.net/cpanelsync/easy/targz.yaml (connected:0).......(request attempt 1/12)...Resolving httpupdate.cpanel.net...(resolve attempt 1/65)... Fetching http://httpupdate.cpanel.net/mirror_addr_list (connected:0).......(request attempt 1/3)......connecting to 74.50.120.123...@74.50.120.123......connected......receiving...100%......request success......Done........
  • Dell Perc 6/i SATA benchmarks without battery


    The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results. This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane. Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: N/A De........
  • LSI MegaRAID Adventures, Guide and HowTo


    LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
  • WD 20EARX Dead Again


    Another new drive bad from the start: Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........
  • Asterisk DOS attack - failed for '173.242.117.192' - Peer is not supposed to register [May 23 15:46:07] ERROR[32748]: chan_sip.c:13158 register_verify: Peer '153' is trying to register, but not configured as host=dynamic


    This happened to a customer Asterisk server and it somehow found the ID of the registration account to the upstream SIP server and was railing connection attempts (it filled up the console and there were literally thousands per second). Basically this caused all incoming and outgoing calls to fail. It was a temporary fix but the solution was to block that specific IP, it's hard to stop it 100% because the customer needs the default SIP port.........
  • WD 20EARX 2TB Bad within days


    This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad. ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0 ata1.00: irq_stat 0x40000008 ata1.00: failed command: READ FPDMA QUEUED ata1.00: cmd 60/00:00:........
  • Powersupply Issue, Motherboard AHCI issue?


    This is the most I can get when plugging in a hard drive hot and only on some power connectors. [71656.314271] ata5: exception Emask 0x50 SAct 0x0 SErr 0x90a02 action 0xe frozen [71656.314277] ata5: irq_stat 0x00400000, PHY RDY changed [71656.314285] ata5: SError: { RecovComm Persist HostInt PHYRdyChg 10B8B } [71656.314294] ata5: hard resetting link [71660.360686] ata5: softreset failed (device not ready) [71660.360694] ata5: applying........
  • Setup PXE Boot using Centos and dhcpd, tftp and syslinux


    This is something I often setup for clients because it's very helpful for people in datacenters, this allows custom OS installs on demand, you can customize it more by using kickstart etc.. but here's a base I use before customizing more: This little script below will install everything you need to get booting by PXE Linux. It also assumes you set a local IP (be sure not to overwrite your existing IP) on eth0:0 (note the :0) as 192.168.1.10 and it........
  • KVM compilation issue/solution - Disabling PIE due to missing toolchain support glib-2.12 required to compile QEMU


    qemu-kvm-1.2.0]# ./configure Disabling PIE due to missing toolchain support glib-2.12 required to compile QEMU Solution install glib2 *Don't confuse glib2 with glibc, they are different and it may catch some off guard. yum -y install glib2* After that KVM should compile and install just fine.........
  • failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80)


    [ 12.460014] ata1: SRST failed (errno=-16) [ 17.626677] ata1: link is slow to respond, please be patient (ready=0) [ 22.480011] ata1: SRST failed (errno=-16) [ 27.646681] ata1: link is slow to respond, please be patient (ready=0) [ 38.106817] ata1.01: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80) [ 48.266676] ata1: link is slow to respond, please be patient (ready=0)........
  • How To Test If Your Hard Drive Is Good/Signs of dying hard drive


    I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem: We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........
  • phpMyAdmin - Error Cannot start session without errors, please check errors given in your PHP and/or webserver log file and configure your PHP installation properly.


    The fix for this was setting the correct permissions in /var/lib/php, it needs to be "root.root" And /var/lib/php/session needs to be "root.apache" to work properly. After that I was able to login to phpMyAdmin as normal. This whole thing happened because I accidentally changed all of /var/lib to root.root.........
  • Are my WDEARS20 Drives dying already?


    This happened during a RAID array check: SMART says both drives pass the test, but I'm doing a long test on them and hopefully this is not a hardware error. Apr 3 04:22:01 remote kernel: md: syncing RAID array md2 Apr 3 04:22:01 remote kernel: md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc. Apr 3 04:22:01 remote kernel: md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for reconstruction. Apr........
  • SPAMASSASSIN Enable Pyzor and DCC


    *Remember to restart spamassassin after all of this. DCC wget http://www.dcc-servers.net/dcc/source/dcc.tar.Z tar -zxvf dcc.tar.Z cd dcc-1.3.138/ ./configure;make;make install #enable DCC, uncomment the line that disables it near the top vi /etc/mail/spamassassin/v310.pre pyzor wget http://sourceforge.net/projects/pyzor/files/pyzor/0.5.0/pyzor-0.5.0.tar.gz/down........
  • ls: error while loading shared libraries: libtermcap.so.2: cannot open shared object file: No such file or directory solution


    ls ls: error while loading shared libraries: libtermcap.so.2: cannot open shared object file: No such file or directory This is not an ldd problem or case of anything missing, this only happened after I upradedUbuntu. declare -x PATH="/home/user/bin:/usr/local/bin:/usr/bin:/bin:/usr/games" "/home/user/bin" is the problem! It's weird because I have no idea how it happened.........
  • Amarok won't play songs, keeps skipping to the next


    Amarok won't play songs, keeps skipping to the next Some say install install phonon-backend-xine but it was already installed automatically, obviously that's not the problem or solution. Settings -> Configure Amarok Playback: Configure Phonon Audio Output: Music It should show your different audio interfaces, choose Pulse Audio and move it to the top of the list, do the Apply, OK and manually quit Amarok (remember to close it from the tra........
  • Postfix/Any Email Server check for Open Relay


    The first thing you need to remember is not to check from the same host/server itself. This is a silly mistake I made, the reason is that many mailservers and especially postfix are configured to allow relaying from the localhost/same host. If you do that you'll get a false positive. *Make sure you test from another host/system than the mail server itself! telnet yourmailserverhost.com 25 220 Courier (FreeBS........
  • Failed to save enabled features : The Suexec command on your system is configured to only run scripts under /var/www, but the Virtualmin base directory is /home. CGI and PHP scripts run as domain owners will not be executed.


    Apache/httpd Failed to save enabled features : The Suexec command on your system is configured to only run scripts under /var/www, but the Virtualmin base directory is /home. CGI and PHP scripts run as domain owners will not be executed. This is because I never edited the Apache Config and Virtualmin config to reflect my new/current updated structure.........
  • Webmin/Virtualmin when enabling bind: Failed to save enabled features : Virtualmin is configured to setup DNS zones, but this system is not setup to use itself as a DNS server. Either add 127.0.0.1 to the list of DNS servers, or turn off the BIND fe


    Webmin/Virtualmin when enabling bind: Failed to save enabled features : Virtualmin is configured to setup DNS zones, but this system is not setup to use itself as a DNS server. Either add 127.0.0.1 to the list of DNS servers, or turn off the BIND feature on the module config page. It means what it says, add "127.0.0.1" to /etc/resolv.conf........
  • Installing Webmin & Enabling SSL


    Webmin Setup Centos 5: wget http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html&ts=1294339690&use_mirror=surfnet [1] 24229 [2] 24230 [root@host ~]# --2011-01-06 21:48:20-- http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html Resolving downloads.sourceforge.net... 216.34.181.........
  • Virtualmin/Webmin Postfix Error: The status of your system is being checked to ensure that all enabled features are available, that the mail server is properly configured, and that quotas are active ..


    Virtualmin Postfix Error: The status of your system is being checked to ensure that all enabled features are available, that the mail server is properly configured, and that quotas are active .. A problem was found with your Postfix virtual maps : No map sources were found in the Postfix configuration .. your system is not ready for use by Virtualmin. ........
  • Dying Seagate 7200.11 SD15


    [137392.910057] ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x80000 action 0x6 frozen [137392.910077] ata4: SError: { 10B8B } [137392.910095] ata4.00: cmd 60/20:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 16384 in [137392.910099] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [137392.910122] ata4.00: status: { DRDY } [137392.910135] ata4: hard resetting link [137393.440060] ata4: SATA link........
  • Ubuntu/Debian DRBD 8.0 Setup Guide


    I've only used it on Centos, soI thought I'd make a quick Debian guide: Install the DRBD Package apt-get install drbd8-utils Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: libswfdec-0.8-0 Use 'apt-get autoremove' to remove them. The following........
  • mdadm RAID 1 adventures


    I separated the 2 drives in the RAID 1 array. 1 is the old one /dev/sda and is out of date, while the separated other one /dev/sdc was in another drive and mounted and used with more data (updated). I wonder how mdadm will handle this: usb-storage: device scan complete md: md127 stopped. md: bind md: md127: raid array is not clean -- starting background reconstruction raid1: raid set md127 active with 1 out of 2 m........
  • Nautilus/GNOME File Manager handy list of extensions


    nautilus-gksu - privilege granting extension for nautilus using gksu nautilus-sendto - integrates Evolution and Pidgin into the Nautilus file manager nautilus-share - Nautilus extension to share folder using Samba nautilus-actions - nautilus extension to configure programs to launch nautilus-bzr - Bazaar (bzr) integration for nautilus nautilus-cd-burner - CD Burning front-end for Nautilus nautilus-clamscan - Antivirus scanning for Nautilus n........
  • mdadm when a RAID 1 member dies


    [27969.398749] sd 5:0:0:0: [sdb] 3907029168 512-byte hardware sectors (2000399 MB) [27969.398749] sd 5:0:0:0: [sdb] Write Protect is off [27969.398749] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [27969.398749] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [27972.117543] ata6.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 [27972.117543] ata6.00: irq_stat 0x48000000 [27972.117543] ata6.00: cmd 60/08:00:ff:7........
  • Fix Slow 2D Graphics Xorg.conf Ubuntu/Debian/Mandriva Linux


    I'm using Ubuntu 8.04 but anyone using older kernels will find this may apply to them. My Intel graphics are very slow with the default Xorg settings but by using "EXA" acceleration, scrolling down windows of text becomes pretty snappy. Just edit /etc/X11/xorg.conf Section "Device" Identifier "Configured Video Device" &nb........
  • CPanel Solution for Error Missing HOST Config Line in /etc/wwwacct.conf, please reconfigure with Edit Setup.


    Edit /etc/wwwacct.conf Then add/edit the HOST line to add your hostname. eg: HOST yourcpanelserver.com........
  • Compile PHP 5.3.2 on Centos 5 and CPanel/WHM because of error - Fatal error: Call to > undefined function imagecreatefromjpeg()


    This function and others may not work with the stock PHPinstall on Centos/CPanel: Fatal error: Call to > undefined function imagecreatefromjpeg() Even with libjpeg-devel installed it won't work because PHP was not compiled with jpeg support, so we have to do the dirty work ourselves :) Here is the command/yum's I did to install missing libraries for PHP that configure will complain about (yes it is a one by one process). yum install bzip2-........
  • Seagate Drive 500GB Drive Dying


    This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device........
  • Linux AHCI Hotswap Tips - Remember To Reread The Partition Table WITHOUT rebooting


    From the package "parted" you can use the command "partprobe" to re-read the partition table. I really hate rebooting, and that's what Iloved to hear about AHCI motherboards, that they allow hotswap so you don't have to reboot. But that's only as good as the OS, if the OS does not reload the partition table you won't be able to do anything with that new drive you attached without rebooting. Yes, even without re-reading the partiton table Linux will........
  • Need identd for port 113 ? Install authd


    Need identd for port 113 ? Install authdyum install authd Happy identing :)Actually it's not that simple. It installs as an "xinetd" service and is disabled and turned off by deafult. To enable it run: [code:1:8c94df8319] chkconfig --level 3 auth on service xinetd restart [/code:1:8c94df8319] This will set identd aka authd to start by default. service xinetd resta........
  • E-mail (Thunderbird) with GnuPG encryption


    E-mail (Thunderbird) with GnuPG encryptionThis is great tool for Mozilla Thunderbird which allows you to encrypt your e-mails so only you and the receiver can view it even if the e-mail is intercepting or obtained by another person. The only small catch is that you of course have to install an extension to Thunderbird and then configure each account you want to use it with. Really it can probably all be done in a few minutes and the effort is worth it.........
  • pound a Linux Load Balance and Reverse Proxy


    I have played around with Pound a little bit. It is a reverse proxy and load balancer in one, and it can be used as only a reverse proxy if you like. It is very simple to configure as either, and Pound even senses if one of the systems is down and stops sending requests to the dead server. It supports SSL (but passes the request to the destination server unencrypted) and even the Apache log format. Pound is very simple, fast a........
  • Clustered/Distributed Network Filesystems, Which Ones live up to the hype?


    I've tried to find a good sensible solution to cluster with and each technology has it's pros and cons and there is no perfect solution and I've found a lot of "exaggerations" in the applications, benefits and performance of these different filesystems. DRBD I first started off with DRBD and Ihave to say it does live up to the hype, is quite reliable (although it can be annoying to match up the kernel module and user applications since they must match and whe........
  • Configuring OCFS2 Clustered File System on Debian Based Linux including Ubuntu and Kubuntu


    There's a lot of information and guides on OCFS2 for RHELand Centos Linux but the package setup and configuration is slightly different and this has thrown some people off. Installing OC2FS You should install the following packages to get started: apt-get install ocfs2-tools ocfs2console Configure OC2FS In RHEL/Centos the main configuration file is located in /etc/sysconfig/o2cb However in Debian based Linux it is located........
  • LAME MP3 Encoder Segmentation Faults


    This happened on one of my Ubuntu machines where Igot some kind of segfault on line 21 from LAME at random while encoding MP3s (a second try is fine usually). I've read that it's best to compile it from source and that has solved most issues for people. Here is my preferred configure line: ./configure --enable-mp3x --with-fileio=lame --enable-debug --with-vorbis Even with that I got a different error this tim........
  • Latest Articles

  • FreePBX 17 How To Add a Trunk
  • Docker Container Onboot Policy - How to make sure a container is always running
  • FreePBX 17 How To Add Phones / Extensions and Register
  • Warning: The driver descriptor says the physical block size is 2048 bytes, but Linux says it is 512 bytes. solution
  • Cisco How To Use a Third Party SIP Phone (eg. Avaya, 3CX)
  • Cisco Unified Communication Manager (CUCM) - How To Add Phones
  • pptp / pptpd not working in DD-WRT iptables / router
  • systemd-journald high memory usage solution
  • How to Install FreePBX 17 in Linux Debian Ubuntu Mint Guide
  • How To Install Cisco's CUCM (Cisco Unified Communication Manager) 12 Guide
  • Linux Ubuntu Redhat How To Extract Images from PDF
  • Linux and Windows Dual Boot Issue NIC Won't work After Booting Windows
  • Cisco CME How To Enable ACD hunt groups
  • How to install gns3 on Linux Ubuntu Mint
  • How to convert audio for Asterisk .wav format
  • Using Cisco CME Router with Asterisk as a dial-peer
  • Cisco CME How To Configure SIP Trunk VOIP
  • Virtualbox host Only Network Error Failed to save host network interface parameter - Cannot change gateway IP of host only network
  • Cisco CME and C7200 Router Testing and Learning Environment on Ubuntu 20+ Setup Tutorial Guide
  • Abusive IP ranges blacklist