Warning: The driver descriptor says the physical block size is 2048 bytes, but Linux says it is 512 bytes. solution

Disk /dev/sdb: 15.22 GiB, 16336814080 bytes, 31907840 sectors Disk model: SD/MMC Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x00000000 The fdisk output is above and below is the error you may get when trying to use the d........

Using Cisco CME Router with Asterisk as a dial-peer

#Remember that you need a valid gateway IPunless the Asterisk server is on the same subnet and LAN Set Valid Gateway IP (if you don't have one already) ip route 0.0.0.0 0.0.0.0 GATEWAYIP Enable VOIPTrust voice service voip ip address trusted list ipv4 0.0.0.0 0.0.0.0 sip Set Credentials For Asterisk and Register To Asterisk sip-ua........

CentOS 7 fix Could not retrieve mirrorlist http://mirrorlist.centos.org/?release=7&arch=x86_64&repo=os&infra=container error was 14: curl#6 -

yum update Loaded plugins: fastestmirror, ovl Determining fastest mirrors Could not retrieve mirrorlist http://mirrorlist.centos.org/?release=7&arch=x86_64&repo=os&infra=container error was 14: curl#6 - "Could not resolve host: mirrorlist.centos.org; Unknown error" One of the configured repositories failed (Unknown), and yum doesn't have enough cached data to continue. At this point the onl........

hostapd example configuration for high speed AC on 5GHz using WPA2

This example is using RTL8821AU chipset from a TP-Link T2U Plus USB adapter and other similar ones should work the same. Here's how to get this chipset RTL8821AU working in Linux. Here's how to get RTL8812 and RTL8822 working in Linux.........

Debian Ubuntu 10/11/12 Linux how to get tftpd-hpa server setup tutorial

apt install tftpd-hpa #change TFTP_ADDRESS to by setting address to 192.168.1.1:69 or the IP you need, otherwise it will listen on all IPs and interfaces which could be a security risk. # edit /etc/default/tftpd-hpa TFTP_USERNAME="tftp" TFTP_DIRECTORY="/srv/tftp" TFTP_ADDRESS="192.168.1.1:69" TFTP_OPTIONS="--secure"........

nvidia cannot resume from sleep Comm: nvidia-sleep.sh Tainted: Linux Ubuntu Mint Debian

This seems to happen in many different drivers but it happened more often in newer versions such as 530 vs 525. Then nvidia-modeset goes to 100% There are many reports of this appearing since driver 4.70 and I can confirm I've seen this in various machines. https://forums.de........

Docker Swarm vs Kubernetes Comparison Guide

A lot of companies are unsure which solution to choose and many may not be aware of Docker Swarm as an alternative to Kubernetes. One thing that many Sysadmins find is that Docker Swarm is simply easier, quicker to setup and maintain by far than Kubernetes.........

When is it time to leave your VPS/VDS Cloud Hosting Provider?

When Is It Time to Leave Your VPS, VDS, and Dedicated Server Provider? Choosing the right hosting solution—be it Virtu........

2024 Buyer's Guide: How to Choose and Buy the Best VPS/VDS for Your Needs - Tips and Strategies

In today’s digital landscape, finding a reliable and secure Virtual Private Server (VPS) or Virtual Dedicated Server (VDS) goes beyond just comparing specs and prices. With increasing concerns over data privacy, security breaches, and government surveillance, the wisdom of choosing your VPS/VDS provider based on juri........

How To Upgrade Debian 8,9,10 to Debian 12 Bookworm

Step 1.) Upgrade to Debian 11 first The process to go to Debian 12 is not as smooth as 11, when trying to upgrade from Debian 10. In fact, it doesn't work directly, so you'll first need to follow this guide to update to Debian 11, reboot and come back here if successful. Step 2.) Update sources.list Update your /etc/apt/sources.list like this: deb http://........

How To Setup Python3 in Ubuntu Docker Image for AI Deep Learning

The issue is that Docker images are stripped down, so many tools and even python3 is missing, so you'll have to build or update the actual image yourself. I assume you have started an image with something like this and that you have the Nvidia Toolkit installed (assuming you are using GPUs). If you're not using nvidia just remove --runtime=nvidia --gpus all. docker run -it --runtime=nvidia --gpus all ubuntu bash These works for most images li........

talib/_ta_lib.c:747:10: fatal error: ta-lib/ta_defs.h: No such file or directory

If you are installing ta-lib for Python and get this error then you can normally solve it by manually getting the ta-lib source files and compiling. tar -zxvf ta-lib-0.4.0-src.tar.gz cd ta-lib;./configure;make;make install Collecting ta-lib Downloading https://files.pythonhosted.org/packages/39/6f/6acaee2eac6afb2cc6a2adcb294080577f9983fbd2726395b9047c4e13ec/TA-Lib-0.4.26.tar.gz (272kB) &nbs........

Virtualbox Best Networking Mode In Lab/Work Environment without using NAT Network or Bridged

Virtualbox is a very powerful tool, but for some use cases it is less than optimal. Say you are in a work, lab or other environment where you are not alone on the physical network and there could be overlap of IPs, but you need all of your VMs to be contactable from your host, VMs need to communicate with each other, and VMs need internet. NAT Network will give you VM to VM communication and internet, however, it is buggy and unstable. It also doesn't allow host to VM co........

Enable Turbo Mode for CPU Ubuntu Linux Mint Debian Redhat

Sometimes due to your BIOS/EFI you may find that you have chosen "Energy Efficient" for your CPU which may effectively disable turbo mode. This is because "Energy Efficient" will often restrict or throttle your CPU to the base speed. This can impact nearly any CPU such as Intel's, AMDs, Opteron, Xeon etc... This is of course frustrating, for example if you have a CPU that is 2.0GHz base speed but turbo to 2.5GHz, you will never hit more than 2GHz.........

docker / kubernetes breaks Proxmox QEMU KVM Bridge VMs

Docker adds iptables rules that break a lot of things including MASQUERADE or anything that needs the FORWARD table. If NAT is not working after Docker installation, it is probably because it set the iptables FORWARD policy to DROP. This may also make you think that your br0 or bridge is not working, but it's likely just due to what we'll mention later on below, that, Docker probably set your FORWARD chain to default DROP all packets, so nothing on your bridge ever makes it out........

Loaded: masked (Reason: Unit hostapd.service is masked.) Solution in Linux Debian Mint Ubuntu

If you are getting this error from systemctl "Loaded: masked (Reason: Unit hostapd.service is masked.)" we need to unmask the service. Solution systemctl unmask hostapd Removed /etc/systemd/system/hostapd.service. It's fixed root@routerOS:/var/log# systemctl start hostapd root@routerOS:/var/log# systemctl status hostapd ● hostapd.service - Access point and authentication server for Wi-Fi and Ethern........

How To Tell Which Repository a Package Comes From Debian Mint Ubuntu

Just use apt-cache policy to find the repo of a package: apt-cache policy lxd lxd: Installed: 3.0.3-0ubuntu1~18.04.2 Candidate: 3.0.3-0ubuntu1~18.04.2 Version table: *** 3.0.3-0ubuntu1~18.04.2 500 500 http://archive.ubuntu.com/ubuntu bionic-updates/main amd64 Packages &nb........

Docker Tutorial HowTo Install Docker, Use and Create Docker Container Images Clustering Swarm Mode Monitoring Service Hosting Provider

The Best Docker Tutorial for Beginners We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........

HongKong VPS Server, Cloud, Dedicated Server, Co-Location, Datacenter The Best Guide on Hong Kong, China Internet IT/Computing

In our 2024 VPS Server/Cloud Buyer's Guide, we place the location of your VPS/hosting/server as one of the priorities that is often overlooked. 2024 Update - Datacent........

Linux Ubuntu Debian Centos Mint - How To Check if Intel VT-x or AMD-V Hardware Virtualization is Enabled?

From the terminal do this: cat /proc/cpuinfo|grep -E "svm|vmx" You should get output like this(svm = AMD-v and vmx=Intel-VTx): flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc cpuid aperfmperf pni pclmulqd........

EFI PXE grub2 Howto guide for Linux EFI PXE Booting on Debian, Mint, Ubuntu, RHEL

Just a quick note and warning is that if you are testing to see if EFIPXE booting works on a VM, MAKE SURE it actually works. For example Iinitially tested using my Distro's QEMU 2.5+dfsg-5ubuntu10.46 and ovmf BIOS firmware (OVMF supports EFI). However, I found on old versions of QEMU (like 2.5), EFIbooting with GRUB NEVER works so it may appear that you have made a mistake when everything is fine when you boot a physi........

Linux Grub not booting the intended kernel solution in Debian, Mint, Ubuntu how to specify which kernel to boot by default

Traditionally kernels were numbered starting from 0 but by default the "new style" of grub boot loading considers each subkernel item to be different so if you have 3 entries for 4.40-148 rather than counting for 1. To get the expected behavior let's show this example and how we can boot it We do a grep on menuentry in /boot/grub/grub.cfg to see all of the bootable kernels rather than scrolling through loads of extra entries we don't care about (thou........

qemu 4 compilation options

How To Compile QEMU Manually (using sensible options) 1.) Download the QEMU source file you want. wget https://download.qemu.org/qemu-4.2.0.tar.xz 2.) Extract The Source File tar -Jxvf qemu-4.2.0.tar.xz 3.) Switch to the extracted source cd qemu-4.2.0 4.) Make sure we have the right libraries and tools to compile QEMU manually sudo apt install build-e........

Huion and Wacom Tablets How To Install in Linux Mint / Ubuntu and make the stylus work properly

It took a lot of fiddling to make a Huion Kamvas 13 Pro work in Linux but it simple once you know what to do. Don't bother searching as it is unlkely there is a guide out there that will actually make your tablet work. It mainly comes down to the fact that the hid_uclogic kernel module is buggy or doesn't support MANYof these wacom based/Huion tablets properly. What was happening with me is that Ihad the Kamvas 13 Huion setup as a secondary screen/monitor.&nb........

CentOS 6 impossible to compile a newer libguestfs

yum -y install gcc make gperf genisoimage flex bison ncurses ncurses-devel pcre-devel augeas-devel augeas readline-devel checking for cpio... cpio checking for gperf... no configure: error: gperf must be installed configure: error: Package requirements (augeas >= 1.2.0) were not met: Requested 'augeas >= 1.2.0' but version of augeas is 1.0.0 yum remove augeas augeas-libs augeas-devel wget http://downl........

How To Get Started on Ubuntu with gpt-2 OpenAI Text Prediction

apt install software-properties-common add-apt-repository ppa:deadsnakes/ppa apt update apt install python3-pip apt install python3.7 curl gnupg python3.7-dev git ln -s /usr/bin/python3.7 /usr/bin/python3 pip3 install numpy keras_preprocessing curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add - echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........

How To Speed Up Linux Ubuntu and Debian Based Computers By Improving CPU Performance and Changing the CPU Governor

I used to believe that for Desktops especially that the "ondemand" CPUfrequency changing that kernels included with Ubuntu and Debian based distros have would be sufficient for snappy performance. However, you can feel the lack of performance on the fastest computer if you have ondemand. A lot of times even under high load 100% of your CPUfrequency in MHz will not be used. For example a 2.8Ghz CPUmay only run at 1.8MHz or even .9GHz. Now........

How To Install OpenProject on Centos 7 Step-by-Step Guide

There are a few caveats that may not be obvious to everyone so I am going to cover them here but keep this in mind before starting. Before starting install epel or you will be missing tesseract: yum -y install epel-release #1) When you specify your SSL certificate with a full path, it really needs to exist where you tell it to (including the default location of /etc/ssl/certs and /etc/ssl/c........

How To Install python 3.4 3.5 and up on Linux with wine - Working Solution

This is sure simple if you follow the guide but it took a lot of hacking around to make this work on Debian/Ubuntu! Now before you ask why bother running wine and python, the reason is because Python executables are NOT cross-platform. If you run pyinstaller in Linux, that binary will only run on Linux and the same if you do it in Windows. So it is preferable if you have a single environment that you can create Linux and Windows binaries from rather than running 2 separate........

CentOS 8 how to convert to a bootable mdadm RAID software array

The cool thing here is that we only need 1 drive to make a RAID 10 or RAID 1 array, we just tell the Linux mdadm utility that the other drive is "missing" and we can then add our original drive to the array after booting into our new RAID array. Step#1 Install tools we need yum -y install mdadm rsync Step #2 Create your partitions on the drive that will be our RAID array Here I assume it is /dev........

PHP 7.2, Apache and Centos 7 How To Install

yum install centos-release-scl yum install rh-php72 rh-php72-php rh-php72-php-mysqlnd Symlink PHP binary: ln -s /opt/rh/rh-php72/root/usr/bin/php /usr/bin/php Symlink Apache and PHP module config: ln -s /opt/rh/httpd24/root/etc/httpd/conf.d/rh-php72-php.conf /etc/httpd/conf.d/ ln -s /opt/rh/httpd24/root/etc/httpd/conf.modules.d/15-rh-php........

How To Install Asterisk 16 17 on Debian Ubuntu Linux

Downloading and compiling from source to get the latest version of Asterisk is really simple with this guide. apt install gcc make g++ libedit-dev uuid-dev libjansson-dev apt install libxml2-dev sqlite3 libsqlite3-dev wget http://downloads.asterisk.org/pub/telephony/asterisk/asterisk-16-current.tar.gz tar -zxvf asterisk-16-current.tar.gz cd asterisk-16.6.2/ ./configure If you get this error change y........

Linux Ubuntu Debian Centos How To Make a Bootable Windows 7, 8, 10, 2016, 2019 Server USB from ISO

Use fdisk on your USB drive to create a bootable NTFS partition (in my case /dev/sdb): sudo fdisk /dev/sdb Welcome to fdisk (util-linux 2.27.1). Changes will remain in memory only, until you decide to write them. Be careful before using the write command. Command (m for help): n Partition type p primary (0 primary, 0 extended, 4 free)........

Debian Ubuntu and Linux Mint Broken Kernel After Date - New Extra Module Naming Convention

I don't consider a lot of these "extra" kernel modules "nice to have" as they often contain drivers for essential items like your soundcard, your NIC and many other devices that may not work. Sometimes you may find that "sound" or "ethernet" worked before a kernel/OS upgrade and now in the new version they don't. Often it will be because you need to install the "extra" kernel modules. One other weird thing is that sometimes........

Cisco Unified Communications Manager / CUCM IP 8.6,10,12 Install Error Solution

Install Errors on Version 12: This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5 on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error. *Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install. What really causes this even though you successfully install........

Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM

The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........

How to install and setup LXC Containers (OpenVZ alternative) on Centos 6 / 7

If you don't aleady have it, you'll need EPEL Install LXC yum -y install lxc lxc-templates Loaded plugins: fastestmirror Setting up Install Process Loading mirror speeds from cached hostfile * base: mirror.it.ubc.ca * epel: mirrors.kernel.org * extras: mirror.it.ubc.ca * updates:........

VBOX VirtualBox How To Import Raw .img Disk File

What you need to do if you have taken a dd or real raw image dump of a hard disk: VBoxManage convertdd windows2019-eval-template.img windows2019.vdi --format VDI The .img is the raw dd dump and the .vdi is the output file. --format VDIspecifies to output to .vdi format If you are in a pinch you can always use qemu-kvm binary and manually specify the .img as your disk and i........

Linux partprobe/partx cannot access last and 4th partition

On a test machine Iwas never able to access to a newly created 4th partiton. As we can see there are dev devices for everything but the 4th partition. The normal "partprobe" or "kpartx" or kernel being told to rescan the block device didn't help (only a reboot did). fdisk -l /dev/sda Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units........

Centos 7 PHP MySQL Not Working Solution

PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/pdo_mysql.so' - /usr/lib64/php/modules/pdo_mysql.so: symbol mysql_options, version libmysqlclient_18 not defined in file libmysqlclient.so.18 with link time reference in Unknown on line 0 #not sure what is wrong with php-mysql but I removed it and installed mysqlnd yum -y remove php-mysql yum -y install php-mysqlnd........

VMWare ESXi 6.7 SSH/PowerShell CLI Commands

[root@localhost:~] BootModuleConfig.sh echo host-ind nfcd........

VMWare Vsphere VCSA Graphical Install Creates json

yes it does create its own json ============================================ cat /tmp/vcsaUiInstaller/ovftool-20180809-175238948-20180809-175603497.log |grep -i json 2018-08-09T17:56:04.238-07:00 verbose OVFTool[30966] [Originator@6876 sub=Default] Manifest file entry: SHA1(VMware-vCenter-Server-Appliance-6.7.0.12000-8832884_OVF10-file1.json) = 1deb658c724767697587d5909c4051c01813e6a1 --> ........

Debian Mint Ubuntu compiling xmr-stak

sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........

wodim / cdrecord error cannot burn DVD or BDR .iso Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error

dvd+rw-mediainfo /dev/sr0 INQUIRY: [ASUS ][BW-16D1HT ][3.00] GET [CURRENT] CONFIGURATION: Mounted Media: 11h, DVD-R Sequential Media ID: RITEKF1&n........

Linux How To Free Wasted Memory RAM in Buffers

We all know Linux is known for good memory management but is it really? It seems all on its own with hardly anything running that you can come back in days or weeks and find that almost all of your RAMis used! And many will say "no don't worry it's buffers for optimization" but it doesn't seem to help because what is in buffers is not available to use for new programs running or ones that allocate more RAM as far as Ican tell. The reason Iknow........

VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI

#mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........

Centos How To Update to Glibc 2.14 Plus

Centos 6 requires GLIBC 2.12 however a lot of new programs you would want to compile may need a newer glibc. You can't remove the old glibc since the whole OS is based on it but you can install the updated glibc alongside it and do an export pointing to your updated GLIBC. mkdir ~/glibc_install; cd ~/glibc_install wget http://ftp.gnu.org/gnu/glibc/glibc-2.14.tar.gz........

cannot mount kvm ntfs image

guestmount -a kvmuserscra.img -m /dev/sda1 mount libguestfs: error: mount_options: /dev/sda1 on / (options: ''): mount: unknown filesystem type 'ntfs' guestmount: '/dev/sda1' could not be mounted. guestmount: Did you mean to mount one of these filesystems? guestmount: /dev/sda1 (ntfs) guestmount: /dev/sda2 (ntfs) yum -y install ntfs-3g still........

yum how to install old obsolete packages

This is important as unfortunately Centos may designate a package obsolete and the replacement breaks everything (eg. you have a config file and the new replacement is not at all compatible with it and it breaks your application). This is where disabling obsoletes comes into play, it can be done from yum but it doesn't work at the time I find. yum --setopt=obsoletes=0 install someapp However Ifind it still installs the new app and not the one you ask for........

M2Crypto.SSL.Checker.WrongHost: Peer certificate subjectAltName does not match host, expected fedora-archive.ip-connect.vn.ua, got DNS:mirror.ip-connect.vn.ua

You are using Centos 5 which is deprecated so nothing in yum will work until you follow this post to use the vault: http://realtechtalk.com/Centos_59_Working_Vault_Repo_file-1921-articles yum update Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * epel: fedora-archive.ip-connect.vn.ua Traceback........

/usr/bin/ld: cannot find -lboost_system-mt-s /usr/bin/ld: cannot find -lboost_filesystem-mt-s /usr/bin/ld: cannot find -lboost_program_options-mt-s /usr/bin/ld: cannot find -lboost_thread-mt-s collect2: error: ld returned 1 exit status make: *** [cag

cagecoin linux compile: sudo apt-get install qt4-qmake libqt4-dev build-essential libboost-dev libboost-system-dev libboost-filesystem-dev libboost-program-options-dev libboost-thread-dev libssl-dev libdb++-dev libminiupnpc-dev Solution: sed -i s/"BOOST_LIB_SUFFIX=-mt-s"/"#BOOST_LIB_SU........

ffmpeg trouble concatenating similar but different files

When things go wrong your video is basically unplayable or the first video plays fine and then freezes when moving on to the next. Generally if both videos weren't produced with the exact 100% same settings you will have issues. You can try the basic concat but it often won't work right. Solution for me: My example uses 3 videos in total so "n=3" and a=1 to include audio. ffmpeg -threads 12 -i file1.mp4 -........

ffmpeg Linux Mint download, compile and install howto

#if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2 tar -jxvf ffmpeg-3.3.2.tar.bz2 cd ffmpeg-3.3.2/ ./configure --disable-yasm install prefix /usr/local source path ........

Track 01: 34 of 1726 MB written (fifo 100%) [buf 99%] 3.6x.Errno: 5 (Input/output error), write_g1 scsi sendcmd: cmd timeout after 1.897 (40) s CDB: 2A 00 00 00 44 A9 00 00 1F 00 resid: 6144 cmd finished after 1.897s timeout 40s write track da

These errors believe it or not are simply because of not being the root user or running with sudo! However if you didn't know to try as root you'd think there was a problem with your burner or disc Essentially it looks like without root you cannot send the required scsi commands to continue writing. Ithink cdrecord should have built-in tests or safeguards to see if it has the permissions to run the required commands. I guess for more advanced users the idea is simila........

yum Packages skipped because of dependency problems:

Solution: yum -y install --skip-broken package-you-want-to-install Packages skipped because of dependency problems: php56w-mysql-5.6.30-1.w6.x86_64 from webtatic Error: Multilib version problems found. This often means that the root cause is something else and multilib version checking is just pointing out that there is........

mdadm frozen and doesn't realize array is dead/missing failed due to unplugged drives

This was a surprising bug but I unplugged all drives for an array md127. At first it was just 1 drive and mdadm seemed to notice this. I unplugged the second drive taking the array offline but mdadm did not realize it was offline and still showed a non-existent disk as being part of it. This created problems trying to unmount it or even to stop this array with mdadm freezing. As for how to fix it I can only think of making sure you are not in a mounted path of........

remove gpt partition linux

sudo fdisk /dev/sdh WARNING: GPT (GUID Partition Table) detected on '/dev/sdh'! The util fdisk doesn't support GPT. Use GNU Parted. WARNING: The size of this disk is 8.0 TB (8001563221504 bytes). DOS partition table format can not be used on drives for volumes larger than (2199023255040 bytes) for 512-byte sectors. Use parted(1) and GUID partition table format (GPT). The device presents a l........

Centos 6 how to guide convert LVM non-RAID into mdadm 1/10 RAID array live without reinstalling

Here is the scenario you or a client have a remote machine that was installed as a standard/default minimal Centos 6.x machine on a single disk with LVM for whatever reason. Often many people do not know how to install it to a RAID array so it is common to have this problem and why reinstall if you don't need to? In some cases on a remote system you can't easily reinstall without physical or KVM access. So in this case you add a second physical or disk or already ha........

openvz yum problem Centos 6.5 cannot find file on mirror:

#solution Edit /etc/yum.repos.d/openvz.repo For the first two entries comment out #mirrorlist and uncomment #baseurl and then it worked openvz yum problem Centos 6.5 cannot find file on mirror: yum update Loaded plugins: fastestmirror Determining fastest mirrors * openvz-kernel-rhel6: mirrors.ustc.edu.cn * openvz-utils: mirrors.ustc.edu.cn base ........

Virtualbox errors on Ubuntu/Debian/Mint

The solution was to reinstall the vbox dkms package and do a manual modprobe of the modules it makes. I never sorted out the unable to start due to the USB issue, I did have the guest additions installed but the only way to boot was to change the pointing device from USB to PS2 and then to disable the USB controller (if your pointing device is set as USB, disabling USB will not work because it will re-enable by default when it sees your pointing device is USB, this is w........

Howto Convert Xen Image to KVM

#count=10000 makes an image of 10000MB make sure your image is at least the same as your existing dd if=/dev/zero of=yourimage.img bs=1M count=10000 # losetup -fv newimage.raw # fdisk -cu /dev/loop0 # kpartx -a /dev/loop0 # dd if= of=/dev/mapper/loop0p1 # e2fsck -f /dev/mapper/loop0p1 # resize2fs /dev/mapper/loop0p1 # a lot of guides tell you to edit /etc/fst........

Linux Ubuntu Debian Howto Manually Update/Install Thunderbird

wget http://download-location sudo tar xjvf thunderbird-24.2.0.tar.bz2 -C /opt ln -s /opt/thunderbird/thunderbird /usr/bin/thunderbird [sudo] password for one: ln: creating symbolic link `/usr/bin/thunderbird': File exists sudo rm /usr/bin/thunderbird ln -s /opt/thunderbird/thunderbird /usr/bin/thunderbird The above is how Idid it, if you don't do it properly you'll find that you are still using the old version (........

Linux Ubuntu Debian Howto Manually Update/Install Firefox

wget http://download-location mv /usr/bin/firefox /usr/bin/firefox-old sudo tar xjvf firefox-26.0.tar.bz2 -C /opt ln -s /opt/firefox/firefox /usr/bin/firefox The above is how Idid it, if you don't do it properly you'll find that you are still using the old version (so verify in About that it is the new version). I've verified the above method works perfectly, it's great if you're using an older version of Linux and need to update the most........

[Hardware Error]: CPU:0 MC4_STATUS[-|CE|MiscV|-|AddrV|CECC]: 0x9c054c84011c011b [Hardware Error]: cache level: L3/GEN, tx: GEN, mem-tx: RD [Hardware Error]: Northbridge Error (node 0): L3 data cache ECC error.

This server has been running for weeks without issue, it's currently only using 1 of 2 CPUs as it is running in the office as a test bed (mainly due to the handle 12 bay storage/great for testing HDDs). The errors below seem to mainly be from AMD CPUs, it's only happened a single time and in the days since Igot that error it hasn't occurrred. Interestingly enough /proc/cpuinfo still shows all 4 cores of the CPU (Opteron 2373 Quadcore HE) and the functionality doesn't seem........

KVM on Centos 6.3 cannot boot FreeBSD 9.2 AMD64

On the same OS with the same kernels basically I cannot boot FreeBSD installer, I believe the issue is the host CPU. One host runs an Intel and works, while an Opteron 2373 does not work despite suggestions from this thread: http://149.20.54.209/showthread.php?t=36761 I've tried cpu options like "kvm64" "Opteron_G3" and none........

Migrate Linux Mint OS from one drive to another

mount -o bind /proc /sda2/proc mount -o bind /dev/ /sda2/dev mount -o bind /sys /sda2/sys chroot /sda2 mint / # mount -o bind /proc /sda2/proc mint / # mount -o bind /dev/ /sda2/dev mint / # mount -o bind /sys /sda2/sys mint / # chroot /sda2 mint / # cd ~ mint ~ # ls Desktop mint ~ # cd / mint / # ls bin Desktop dev-temp home&nb........

Unixbench Testing

The first is a dual CPU AMD Opteron 2373EE (4 cores x 2) and I think it did bad because it has some old 250GB SATAs which can only do about 65MB/s max sequential reads. I think it should have blown away the second (AMD X4 640 Quad Core). [root@fs12home unixbench-4.1.0-wht-2]# ./Run make all make[1]: Entering directory `/root/unixbench-4.1.0-wht-2' Checking distribution of files ./pgms exists ./src exists........

Dell FS12-NV7 2U Server Information and Guide

I've got one of these for testing projects from work at home and got more than I bargained for with the time I've spent on it due to the storage handing/Perc 6/i cards. My particular model came with the following: 2U Rack Mount Server with Rails 2xOpteron 2373 EE (Quad Core, there is a 6-core version that can be found at times) 16GB RAM 2 x 250GB Seagate SATA 2 x Dell Perc 6/i (horrible and a nightmare to work........

Dell Perc 6/i SATA benchmarks without battery

The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results. This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane. Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: N/A De........

LSI MegaRAID Adventures, Guide and HowTo

LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........

iptables centos error getsockopt failed strangely: Invalid argument

iptables -t nat -A PREROUTING -p udp -m multiport --dports 20,123,443 -j REDIRECT --to-port 53 getsockopt failed strangely: Invalid argument........

Samsung Galaxy Note ICS Corrupting microSDHC partition table?

This was partitioned as a single 32GB VFAT but when I inserted it into the phone it said that it can't read it and now here is how the partition table looks. Interestingly enough the data works and reads fine from the computer still. Disk /dev/sdb1: 32.1 GB, 32085360640 bytes 64 heads, 32 sectors/track, 30598 cylinders, total 62666720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum........

kvm cannot boot xen guest using lvm

This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel. I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk. I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one). This is strange but it seems like this Xen PV guest has some sort of hidden or........

How to Encode all VOBs from a DVD/Bluray VIDEO_TS folder into an XVID

In my case I already copied the VIDEO_TS folder to my hard drive. Here is the command for mencoder: mencoder -dvd-device "myvideobackup/VIDEO_TS" dvd:// -ovc xvid -oac mp3lame -lameopts cbr:br=128 -xvidencopts pass=2:bitrate=-700000 -o myvideobackup.avi Replace "-dvd-device myvideobackup/VIDEO_TS" with the location of your backup files or the /dev device of your DVD drive. The -o myvideobackup.avi is of course the name o........

Samsung Galaxy Note Upgrade to ICS 4.0 microSDHC card not detected/dataloss after upgrading - possible solutions

I backed up everything in the /mnt/sd_card directory thinking that some dataloss could occur for some reason but purposely left my microSDHC unbacked up thinking that "it won't touch that since it's external" and Samsung's and other manufacturers website even say this (that it won't be affected and not to worry etc). Apparently I was wrong, my microSD was "undetected" and asked to be formatted after the upgrade (there goes 3-months worth of family photos). No........

The Importance of a High Quality Power Supply/Power Supplies To Prevent Overheating/System Crash/Hardware Damage

For years I've always built cheap systems believing that there is little difference in more expensive components when it comes to reliability and quality, I generally believe this still except for Power Supplies. I've always bought cheap cases with nice sounding 350-550W stock/cheap/crap power supplies and haven't had any issues for the most part until recently. One such case is an NGEAR case with a 550W Optimax power supply, I always read that these supplies don't produce the........

Linux Ubuntu Nvidia GT430 Lockups/Errors/Freezes NVRM: os_schedule: Attempted to yield the CPU while in atomic or interrupt context

I'm running Ubuntu 10.10 with Asus NVIDIA GT430 2.6.35-32-generic-pae #65-Ubuntu SMP Tue Jan 24 14:06:16 UTC 2012 i686 GNU/Linux Nvidia binary driver: 260.19.06 The screen sometimes completely freezes and locks up or everything starts going very slow: [1903398.100007] NVRM: os_schedule: Attempted to yield the CPU while in atomic or interrupt context [1903402.373210] NVRM: Xid (0001:00): 53, CMDre 00000000 00000080 00000000 00000005 00........

gocr - free Linux OCR (Optical Character Recognition) conversion tool

gocr works great and it's simple, just invoke it like so: gocr filename.png The output will be printed to the screen. My only complaint/concern is that even with standard terminal output (not scanned) from a printscreen, gocr does make mistakes by inserting extra spaces where they don't belong, mistaking letters for numbers etc.. but it's definitely enough to be readable and figure out what you're looking at. I haven't tested yet with scanned input........

Linux how to use find recursively to find certain types of files/extensions

Normally if you're in a certain directory you could do: find *.txt and it will work as expected, but it won't work recursively through child directories, here's the correct way to do it: find . -type f -name *.txt The "-type f" is optional because that means only files, but we could have specified d for directory etc... The above command will work recursively as you'd expect. In that way I find "find" to be un........

vnstat setup guide/tutorial

yum -y install vnstat chown nobody.nobody -R /var/lib/vnstat/ #replace venet0 below with your desired interface sudo -u nobody vnstat -u -i venet0 #edit: vi /etc/sysconfig/vnstat #VNSTAT_OPTIONS="-i venet0" # only use the sed below if you are using venet0 instead of eth0 or replace accordingly sed -i 's/eth0/venet0/g' /etc/sysconfig/vnstat [root@monitor]# yum install vn........

Dying Samsung DVDRW Drive

My Samsung drive failed on me, at first I thought it was the enclosure but a direct SATA connection causes the same problems for discs that are inserted. It will work fine for a few minutes but then starts spewing the errors below. I've never been a fan of Korean made optical drives and have always had trouble with them. The problem is that I don't believe NEC and Lite-ON make drives anymore, and I considered them the leaders. Apr 7 11:58:48 bo........

WD EARS Advanced Format Can't be fixed?

There's no partial WD EARS alignment fix: I had data on /dev/sda3 and /dev/sdb3 (RAID1) so I couldn't edit that one. I thought I'd be smart and try fixing the first two partitions so I set the first one starting at sector 2048 and then +8 for the second partition. This has really slowed the performance down worse than it ever was! Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, tot........

Ubuntu/Debian DRBD 8.0 Setup Guide

I've only used it on Centos, soI thought I'd make a quick Debian guide: Install the DRBD Package apt-get install drbd8-utils Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: libswfdec-0.8-0 Use 'apt-get autoremove' to remove them. The following........

yum in Centos 5/Xen halts and exits suddenly

yum exits in the middle The problem is this VPS seems to be an OpenVZ template from HyperVM. The only way to make it work was to disable i386 packages since this was an x64 kernel. That shouldn't be necessary but it was the only way to make yum stop quitting after the first package or two. I couldn't find any issue by checking the logs either. echo y|yum install vim-minimal telnet expect jwhois net-tools slocate iptables elinks gawk L........

PHP CURL SSL won't work or connect

I spent so much time debugging this, most sites don't tell you a very important option to use with CURL and you will only find out this is the problem by running the PHP script from the command line you get the following output that shows the issue (I don't see any way to get this output from Apache itself). * About to connect() to ip.ip.ip.ip port 25000 * Trying ip.ip.ip.ip... * connected * Connected to ip.ip.ip.ip (ip.ip.ip.ip) port 25000 * succes........

mencoder Linux CLI video editing how to encode video file into xvid and split by time into multiple parts

Mencoder is great, you can throw anything at it, including video files from your camera and have it encode into xvid or almost any other format. In my case I took 640x480 video from my Canon and reduced the size by 1/3 with the options below (there are many other options that you can read about in the manual but I like to keep it simple). Mencoder Encode mencoder -ovc xvid -oac mp3lame -xvidencopts fixed_quant=4 -o ........

FUSE/Curlftpfs mount ftp account as drive partition in Linux

This is a great way to use your ftp server space, for example on your web hosting account (althoughI believe many hosts don't allow storage like this), but if you have a VPS/Dedicated Server etc.., this would be perfect. Imagine how easy it is to work with an ftp account that you can just mount as a normal partition or directory in Linux, it would be great for backups etc.. Name curlftpfs - mount a ftp host as a local directory Synopsis........

CPanel Use /scripts/easyapache to recompile Apache/PHP with different options

I used the "Image Manipulation and Security Options" and let the script do the rest. /scripts/easyapache For whatever reason, doing a manual compile of PHPmyself broke everything and I've never seen that before, that's why I resorted to the cheat of easyapache.........

CPanel OpenVZ VPS Error - * Notice * No working loopback device files found. Try running `modprobe loop` as root via ssh and running this script again.

Ihave no idea how to get the loopback device working in OpenVZ, but what's more frustrating is that I purchased a CPanel license for my VPS and clearly it is not "VPS Optimized". Although everything does seem to work at this point despite that error. The suggestions here: http://forum.openvz.org/index.php?t=msg&goto=1339 don't seem to work at all. This is an OpenVZ issue, but also a CPanel isue, why on earth would loopback support be expected in a VPS a........

Windows install blue screen of death caused by faulty optical/DVD-RW drive.

I took an educated guess because it kept happening at the same spot when loading the XP install. I thought it was the hard drive or motherboard. But it turns out my heavily used but loved NEC 3500 DVD-RW drive was the culprit. After disconnecting it and swapping it for another much beloved Pioneer DVD-RW, everything has gone smoothly. I never ran into this or many issues because I've hardly used this drive since moving it to another Desktop years ago. I actua........

rsync my favorite/best/optimal default switches and options

Not sure what rsync switches/options to use? rsync -PDrphogtl The short version would be: rsync -Pha I think these are really common sense options to use and probaby should be the default. Explanation of rsync switches P = display the progress D = hybrid of --specials and --devices so all special and device files will be copied as well. r = recursive (otherwise rsync won't copy files deeper than........

Picking an FTPD (vsftpd) Server in Linux Centos/Debian

I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find. yum search ftp Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * rpmforge: ftp-stud.fht-esslingen.de * base: mirrors.netdna.com * updates: updates.interworx.info * addons: yum.singlehop.com * extras: mirrors.netdna.com rpmforge........

Compaq V2405CA Laptop - Unixbench Performance Test

Here are the results, it is Sempron 3000+ AMD Mobile, 500Gig HDD, 512MB RAM with shared ATI Radeon graphics. # # # # # # # ##### ###### # # #### # # # # ## # # # #&nb........

PHP cannot access /usr/bin/openssl

PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist: [code:1:1fd0f3abbe] if (!file_exists($OPENSSL)) { //echo "ERROR: OPENSSL $OPENSSL not foundn"; }[/code:1:1fd0f3abbe] I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........

The New Chips on the Block

The New Chips on the BlockThe New Chips on the Block By Bruce Gain Story location: http://www.wired.com/news/infostructure/0,1377,67795,00.html 02:00 AM Jun. 13, 2005 PT We have embarked upon a new era in x86 PC computing -- so say chip giants AMD and Intel following their launches of dual-core PC processors. So how will dual-core processing change your PC computing experience? Our FAQ should help you decide whether or when you sho........

Intel's Finnish Fetish

Intel's Finnish FetishIntel's Finnish Fetish By Dave Mock June 13, 2005 Chipmaker Intel (NASDAQ: INTC) has successfully topped the personal computer market for decades. Breaking into related areas such as communications has been much difficult for the world's largest semiconductor maker. But a new partnership with Nokia (NYSE: NOK) could help to change that. Intel's forays into cellular-phone and home-entertaiment-device chips have........

NEC ND-3500A is great!

NEC ND-3500A is great!I just picked up an NEC 3500A a few weeks ago and I love it. It is a great all in-one optical drive solution. It can burn DVD/+R-R at up 16x, read at 16x and rewrite at 4x and CD-R at up to 48x! Not bad, but the impotant part is that it delivers consistent high quality burns and the drive is as quiet as I could ask it to be. It's also convenient that it has a lot of hacked firmware for overspeeding of........

Nice Search Engine Optimization Tools

Nice Search Engine Optimization Toolshttp://searchenginewatch.com/facts/article.php/2156041 I quickly checked this out and I like the Google tool that helps you determine the popularity of certain keywords and then it gives you other related search terms that those people used to search with. Excellent :)........

Create/Enable SSL Certificates for Apache on Linux/Unix Systems eg. Redhat,Centos,Debian

Shortcut/Easiest Way To Create A Self-Signed Key: openssl req -new -x509 -nodes -days 1530 -out server.crt -keyout server.key Using the above, you instantly create a self-signed certificate valid for 1530 days and you can simply skip to step #5.) below. If You Need a Real SSLCertificate (eg. Equifax/Openssl) then you need to create a CSR request (you'll need to follow Steps 1.) and 2.) in order to create the CSR. You then upload the CSR Certi........

Unixbench Score with Glusterfs/Openvz & Quad Core Xeon - Updated with GlusterFS 2.0.8 & Optimized Client Config

The results are still not flattering and are nothing close to native performance. Unless GlusterFS has a "DRBD-like" option to delay writes over the network and to only read from the client side, I don't see how performance can ever improve much more. After doing some client optimizations Iadded more to the score: Start Benchmark Run: Sun Nov 29 00:37:44 PST 2009 00:37:44 up 3 min, 1 user, load average: 0.01........

yum error not working rpmdb: mmap: No such device TypeError: rpmdb open failed

Loaded plugins: fastestmirror rpmdb: mmap: No such device error: db4 error(19) from dbenv->open: No such device error: cannot open Packages index using db3 - No such device (19) error: cannot open Packages database in /var/lib/rpm Traceback (most recent call last): File "/usr/bin/yum", line 29, in ? yummain.user_main(sys.argv[1:], exit_code=True) File "/usr/share/yum-cli/yummain.py&qu........

iPhone 3GS 32GB "Harsh Review"

Yes, Iadmit I finally got bitten by the hype as much as I can usually see through it all. Keep in mind this review is of the "stock" phone, no jailbreaking yet which is what really unleashes the customizability and whyI bought iPhone. I had better things to say about this phone before buying it, and it is a great phone, perhaps the best on the market by far, if not because of the Mac OS port onto the iPhone and all the apps, etc, etc. With that said........

Apple iPhone 3GS and predecessors are leading a revolution

As much of a computer nerd as Iam, I'm usually a late adopter to technology for a few reasons. Ifeel most new hyped technologies and electronics are mainly fads, and I'm also cheap. Adopting later means you avoid the bugs, kinks and most importantly pay the lowest price, that's me being cheap again :) I never read much about the iPhone but Isaw all the hype around it and until recently I wasn't a big fan of anything Apple until a few years ago I realize........

mkisofs error "genisoimage: Directories too deep for 'Backup/My Documents/My Music/iTunes/Album Artwork/Local/5928CE9C1AFAC465/07/15' (7) max is 6."

genisoimage: Directories too deep for 'Backup/My Documents/My Music/iTunes/Album Artwork/Local/5928CE9C1AFAC465/07/15' (7) max is 6. Some people said choosing the --iso-level-4 option will help. I just opted to add the "-D" switch and everything was fine.........

LAME MP3 Encoder Segmentation Faults

This happened on one of my Ubuntu machines where Igot some kind of segfault on line 21 from LAME at random while encoding MP3s (a second try is fine usually). I've read that it's best to compile it from source and that has solved most issues for people. Here is my preferred configure line: ./configure --enable-mp3x --with-fileio=lame --enable-debug --with-vorbis Even with that I got a different error this tim........