• hostapd how to enable and use WPS to connect wireless devices like printers


    Edit your /etc/hostapd/hostapd.conf file like below and restart hostapd. #WPS stuff # Enable control interface for PBC/PIN entry ctrl_interface=/var/run/hostapd eap_server=1 wps_state=2 ap_setup_locked=1 wps_pin_requests=/var/run/hostapd.pin-req config_methods=label display push_button keypad #WPS model info stuff change to suit your needs device_name=USB2.0 WLAN manufacturer=ATHEROS model_name=WAP........

  • How to configure OpenDKIM on Linux with Postfix and setup bind zonefile


    This guide assumes you have a working Postfix server and want it to sign with DKIM. There are a few things we have to understand to make all of this work though, which require you to be familiar with DNS as well. 1.) Install OpenDKIM apt install opendkim systemctl enable opendkim 2.) Edit /etc/opendkim.conf Syslog yes SyslogSuccess yes Mode&nbs........

  • Debian Ubuntu 10/11/12 Linux how to get tftpd-hpa server setup tutorial


    apt install tftpd-hpa #change TFTP_ADDRESS to by setting address to 192.168.1.1:69 or the IP you need, otherwise it will listen on all IPs and interfaces which could be a security risk. # edit /etc/default/tftpd-hpa TFTP_USERNAME="tftp" TFTP_DIRECTORY="/srv/tftp" TFTP_ADDRESS="192.168.1.1:69" TFTP_OPTIONS="--secure"........

  • How to kill a docker swarm


    Assign way more replicas than you have of memory on all nodes and watch the Swarm crash which can easily reproduce in a small VMfor testing. root@Deb11Docker01:~# docker ps CONTAINER ID IMAGE COMMAND CREATED STATUS PORTS NAM........

  • REFUSED unexpected RCODE resolving bind/named error


    Are you getting this error when trying to connect to a site/domain/service and then you checked your router/nameserver's logs to see what's wrong? You may see something like this: named[3025898]: REFUSED unexpected RCODE resolving This is not usually an error with named or bind, at least not on your end but NORMALLY this is an issue with the remote nameserver. A lot of times this is a misconfigured remote nameserver. A classi........

  • Postfix / sendmail config for DKIM, SPF and DMARC Tutorial Guide E-mail Delivery for Hotmail.com Gmail.com and More HowTo


    This will be the goto to help solve e-mail delivery issues and talk about many practical issues that happen between developers, admins and scripts that send e-mail and do things that may not be acceptable or cause deliverability problems. Sendmail Stuff Edit /etc/mail/sendmail.mc The problem is that if you send directly out from the server using the mail function, the Return-path of the e-mails will be username@thehostnameoftheserver.com. Let........

  • Proxmox How To Rename Node Hostname Fix Solution


    Proxmox's documentation shows the following here. Which mainly just says change /etc/hosts and /etc/hostname with your new hostname. Here's what happens if you only do that: If you just do the above, you will find you have an inaccessible original hostname that contains those VMs and you cannot........

  • Proxmox install issue cannot see the buttons or install wrong / bad resolution cannot see the entire screen problem solution


    If you are using a hypervisor to test Proxmox (eg. Vbox) then changing the video card/display adapter can fix it. For example VboxSVGA causes the issue but switching to VMSVGA fixes it. For example VboxSVGA causes the issue but switching to VMSVGA fixes it. ........

  • How To Upgrade Debian 8,9,10 to Debian 12 Bookworm


    Step 1.) Upgrade to Debian 11 first The process to go to Debian 12 is not as smooth as 11, when trying to upgrade from Debian 10. In fact, it doesn't work directly, so you'll first need to follow this guide to update to Debian 11, reboot and come back here if successful. Step 2.) Update sources.list Update your /etc/apt/sources.list like this: deb http://........

  • apache2 httpd apache server will not start [pid 22449:tid 139972160445760] AH00052: child pid 23248 exit signal Aborted (6) solution Mint Debian Ubuntu Redhat


    If you get this error, it is often because you have configured Apache with modules that weren't actually installed. Eg. you try to load the PHPmodule but didn't actually install the apache2 php module, so the server can't start. In general, this error can often be caused by issues with problematic modules and/or Apache being configured for modules that have not actually be installed (eg. libapache2-mod-php) is missing. The above results in this less than obv........

  • Linux Ubuntu Mint how to check nameservers when /etc/resolv.conf disabled solution


    You'll notice that /etc/resolv.conf contains dire warners on most Linux Desktops. # This file is managed by man:systemd-resolved(8). Do not edit. # # This is a dynamic resolv.conf file for connecting local clients to the # internal DNS stub resolver of systemd-resolved. This file lists all # configured search domains. # # Run "resolvectl status" to see details about the uplink DNS servers # currently in use........

  • Linux How To Upgrade To The Latest Kernel Debian Mint Ubuntu


    How to check what kernel version you have/currently running? uname -rm 5.4.0-91-generic x86_64 The above shows us that we are running 5.4.0-91-generic on the x86_64 architecture. The safest way is to stick with the same flavor eg if you're on generic, and say on kernel 5.4.0 then it makes sense to follow what is below. However, if you are migrating or dual booting between newer hardware (eg. you got a........

  • Firefox how to restore and backup saved passwords and history which files/location


    The passwords are stored in the following locations on Unix/Linux: The directory is usually inside your home like this: ~/.mozilla/firefox logins.json contains the locations, username and password key*.db (usually then name could be key3.db or key4.db) Without the key file you will not see any passwords in Firefox as it is required to in order to decrypt the contents of logins.json........

  • ecryptfs how to change default mount location from Private Ubuntu Debian Centos How


    In a lot of distros like Debian, ecryptfs will mount itself in /home/yourusername/Private This is controlled by Private.mnt which may contain the mount path like this: /home/yourusername/Private Change the default mount location of ecryptfs by modifying this file: home/.ecryptfs/yourusername/.ecryptfs/Private.mnt After you unmount and relogin, you should find ecryptfs is now mo........

  • PXE-E23 Error BOOTx64.EFI GRUB booting is 0 bytes tftp pxe dhcp solution NBP filesize is 0 Bytes


    Be very careful about what filename you specify in dhcpd.conf if you get an error like this: NBP filesize is 0 Bytes PXE-E23:Client received TFTP error from server. If you specify "BOOTx64.efi" then the file had better not be called "BOOTx64.EFI" as it is case sensitive. It's really a case of th........

  • Virtualbox Best Networking Mode In Lab/Work Environment without using NAT Network or Bridged


    Virtualbox is a very powerful tool, but for some use cases it is less than optimal. Say you are in a work, lab or other environment where you are not alone on the physical network and there could be overlap of IPs, but you need all of your VMs to be contactable from your host, VMs need to communicate with each other, and VMs need internet. NAT Network will give you VM to VM communication and internet, however, it is buggy and unstable. It also doesn't allow host to VM co........

  • debootstrap how to install Ubuntu, Mint, Debian install


    In this example we install debian 10 with --variant=minbase which gives us a minimal/tiny install. Don't use variant if you want the full size install. mkdir /tmp/deb10files debootstrap --variant=minbase buster /tmp/deb10files/ Did you get an error? debootstrap --variant=minbase buster /home/theuser/VMs/deb10files/ You'll get this error if you make a directory in your home........

  • Debian Ubuntu apt install stop daemon questions/accept the default action without prompting


    This can be a real pain when automating things and you do an apt install and some packages ask a lot of questions. Make sure you set this variable when running: DEBIAN_FRONTEND=noninteractive Remember as well that if chrooting you will want to run like this: DEBIAN_FRONTEND=noninteractive apt install -y yourpackagename ........

  • Linux How to Check Which NIC is Onboard eth0 or eth1 Ubuntu Centos Debian Mint


    So say you happen to have 2 NICs of the exact same chipset, they will generally show up as the same name, with possibly a different revision in lspci. Normally this is not an issue if you have a server with 4 NICs, generally the eth0 to eth3 appears from left to the right (or right to left on some vendors) so it doesn't take much figuring out. Generally if you have different chipsets for different NICs, it should be easy to know which one is eth0 or the first NIC in the OS.........

  • VboxManage VirtualBox NAT Network Issues Managment Troubleshooting


    If you find your NAT Network is not working properly, the first thing you may want to do is list the networks, check their status and make sure the Network is actually started and configured as you expect (eg. is DHCP on and enabled?). This is a long known, unresolved bug that seems to affect Version 6 randomly and disportionately on especially Mint 20/Ubuntu 18. https://www.virtualbox.org/ticket/1474........

  • Dell PowerEdge Server iDRAC Remote KVM/IP Default Username, Password Reset and Login Information Solution


    Are you new to the company, datacenter or a third party who is responsible for deploying a fleet of servers from scratch. The first step is to normally login to the KVM so you can perhaps manually reinstall, PXE boot the Cloud Image or reimage/reinstall an OS but you need access to the KVM/IP or what Dell calls iDRAC. It's common that you may have forgotten this information or that another employee or colleague has changed the info and did not tell you, that they have left the........

  • Stop ls in Linux Debian Mint CentOS Ubuntu from applying quotes around filenames and directory names


    Later versions of ls try to be helpful and smart to prevent errors in dealing with files with spaces that were tradtionally a pain. However if you need the raw/real filenames, this can break scripts or if you are pasting into a csv etc.... How do you make ls not add the quotes? Add the capital "-N" switch ls -N You could also add an alias to make it more permanent Do this to add it to ~/........

  • Ubuntu Debian Mint Linux How To Update Initramfs Manually update-initramfs


    The easiest way for the current running kernel is: update-initramfs -u -k `uname -r` You could change -k to a specific kernel name if for some reason the current is not running (eg. if you are chrooted or in recovery mode). If you want to update all kernels then use "-k all" update-initramfs -k all -u update-initramfs: Generating /boot/initrd.img-5.4.0-162-generic........

  • grub blank screen how to manually boot kernel and initrd Linux Ubuntu Debian Centos won't boot solution


    You probably didn't do an "update-grub" and grub no longer has any proper menu entries, but before you can fix it let's try to get grub booting anyway. If you get this lovely black grub screen here's how you can get things booting. In my case I have a gpt partition with partition 1 and 2. Partion 1 is just my EFI / ESPand partion 2 /dev/sda2 is my root which includes /boot. You will have to adjust this if you had a separate /boot partition.........

  • ecryptfs How To Backup / Migrate Linux Mint Ubuntu Debian system ecryptfs properly and restore access


    In this scenario, let's say you want to clone your OS at the filesystem level and the source system (the system you want to clone from) is in use. Doing a blind rsync / is a big problem because it uses twice as much space for no reason. The reason for this is that with ecryptfs you have a /home/.ecryptfs directory which has the actual encrypted versions of your files and folders. However your home directory (eg. /home/someuser) is mounted. Doing the blind rsync will ca........

  • br0: received packet on bond0 with own address as source address Linux Solution Mint Debian Redhat CentOS bridge bridging


    A quick fix is to run this command: sudo brctl setageing br0 0 This causes the aging of the MAC address to time out immediately or in 0 seconds, which delete the entry frmo the FDB (Forwarding Database) and causes the error to go away. The default time is 300 seconds or 5 minutes. You can also add it under your br0 definition like this in /etc/network/interfaces to make it permanent and automatic: auto br........

  • How To Do Linux Network Bonding Teaming in Mint Debian Ubuntu


    Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........

  • GlusterFS HowTo Tutorial For Distributed Storage in Docker, Kubernetes, LXC, KVM, Proxmox


    This can be used on almost anything, since Gluster is a userspace tool, based on FUSE. This means that all Gluster appears as to any application is just a directory. Applications don't need specific support for Gluster, so long as you can tell the application to use a certain directory for storage. One application can be for redundant and scaled storage, including for within Docker and Kubernetes, LXC, Proxmox, OpenStack, etc or just your image/web/video files or even da........

  • Docker Tutorial HowTo Install Docker, Use and Create Docker Container Images Clustering Swarm Mode Monitoring Service Hosting Provider


    The Best Docker Tutorial for Beginners We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........

  • How To Startup and Open Remote/Local Folder/Directory in Ubuntu Linux Mint automatically upon login


    Just click on the Start Menu and go to "Startup Applications" Then click on the "Add"Button Now enter the command we need to open the folder/directory automatically using the filemanager For remote SSH host (you need pub key auth for it to open without a pa........

  • How To Create OpenVPN Server for Secure Remote Corporate Access in Linux Debian/Mint/Ubuntu with client public key authentication


    Why choose OpenVPN instead of a firewall appliance? OpenVPN can be a reliable and easy replacement for traditional hardware or just be an additional tool that your company uses so that the firewall can focus on its job rather than acting as a VPNappliance at the same time. When comparing OpenVPN with traditional firewal........

  • Package wget is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source. E: Package 'wget' has no installation candidate. Solution


    These types of errors are normally caused by misconfiguration of your /etc/apt/sources.list. In this example on Debian 10, if you didn't complete the install correctly, you will have no repos enabled and only rely on CDROM. "Package wget is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source. E: Package 'wget' ha........

  • Linux Debian How To Enable Sudo/Sudoers for User "User not in sudoers file" Solution


    If you get an error that you aren't in the sudoers file, this typically means that your user is not designated as an admin with sudo privileges. In plain English, when it comes to some OS's like Debian including 10,11 etc.., by default the user is created without special privileges which is contrary to how Ubuntu/Mint handle the secondary user. Let's check the sudoers file to see the problem.........

  • Ansible Tutorial - Playbook How To Install From Scratch and Deploy LAMP + Wordpress on Remote Server


    1. Let's work from an environment where we can install Ansible on. If you are using an older version of Linux based on Mint 18 or Ubuntu 16, you may want to get the PPA and get the latest version of Ansible that way: sudo apt install gpg sudo add-apt-repository ppa:ansible/ansible sudo apt update........

  • Proxmox Services Won't Start Failed to start The Proxmox VE cluster filesystem. Proxmox VE firewall. PVE Status Daemon. Proxmox VE scheduler. PVE Cluster HA Resource Manager Daemon. PVE Local HA Resource Manager Daemon.


    There are many reasons why Proxmox services may not start, but one common one, is if you have changed your /etc/hostname or /etc/hosts and don't have a valid FQDN (eg. proxmox01 instead proxmox01.com). Failed to start The Proxmox VE cluster filesystem. Failed to start Proxmox VE firewall. Failed to start PVE Status Daemon. Failed to start Proxmox VE scheduler. Failed to start PVE Cluster HA Resource Manager Daemon. Failed to star........

  • Virtualbox Vbox Issue Cannot Enable Nested Virtualization Button is Grayed/Greyed Out and Unclickable HowTo Solution


    In newer of versions of Virtualbox, especially above 6.0 (eg. 6.1 like the example below), a lot of times the "Enable Nested VT-x/AMD-V". If you are having this issue, you will see the option is grayed out. It doesn't mean that your computer does not support virtualization, although it is possible it is disabled in the BIOS. You can verify........

  • How to install Kubernetes with microk8s and deploy apps on Debian/Mint/Ubuntu Linux


    Kubernetes Easy Beginners Tutorial/Architecture Guide Kubernetes is known as container orchestration and we should start at explaining the container part of it. A Container is what runs the actual application and based on an Image, and are more comparable to something like an LXC Container, Virtuozzo/OpenVZ using the Linux Kernel Namespaces feature. Containers run these images as independent, isolated operating environments under the O........

  • Cisco Switch Howto Reset Password


    This was done on a 2900 but applies to all the switches of the same era. Step 1 - Power Cycle and enter recovery mode If you have physical access you can power cycle and hold the mode button down for 15 seconds. After that the SYS light will flash on the switch and you will see the following screenshot. If you don't have physical access (eg. it is a datacenter swich over console only) then power cycle and hit "Ctrl+Pause/B........

  • ksnapshot missing in Ubuntu and Linux Mint Solution


    It has been renamed to kde-spectacle so you install it like so: sudo apt install kde-spectacle You'll find it in your start menu listed as "Take Screenshot"........

  • bash how to hide username/customize prompt Linux Debian Redhat Ubuntu Solution


    Just edit your ~/.bashrc and add this at the very end: export PS1="realtechtalk.com" Then your prompt will look like this: bladeblox:uptime 08:47:14 up 48 min, 1 user, load average: 1.00, 1.07, 0.96 If you wanted a dollar sign at the end then you would change it like this: export PS1=&........

  • Cisco Router Password Reset Howto Guide Solution Cannot Login /Unknown Enable Password 2600, 2800, 2900, 3900


    It is common that you may get access to undocumented equipment and need to reset the password. This applies to many Cisco routers whether 2600, 2900, 3900 etc... Cisco's Guide says to hit Ctrl +Pause/Break but if it doesn't work on some devices causing people to say "cisco password reset pause break does not work", you can see Cisco's alternative key combinations here:........

  • EFI PXE grub2 Howto guide for Linux EFI PXE Booting on Debian, Mint, Ubuntu, RHEL


    Just a quick note and warning is that if you are testing to see if EFIPXE booting works on a VM, MAKE SURE it actually works. For example Iinitially tested using my Distro's QEMU 2.5+dfsg-5ubuntu10.46 and ovmf BIOS firmware (OVMF supports EFI). However, I found on old versions of QEMU (like 2.5), EFIbooting with GRUB NEVER works so it may appear that you have made a mistake when everything is fine when you boot a physi........

  • Debian, Mint Ubuntu how to remove package and associated config files


    If you want to start fresh a lot of people falsely assume that an apt remove and then reinstall or apt --reinstall install package will start you off fresh. To be sure and remove all associated config files do the below with the example of ssh server (don't remove it though if you actually use it!) The key below is using the --purge flag or apt-get purge proftpd (eg sudo apt --purge remove packagename) apt purge proftpd; apt install proftpd........

  • How To Replace Audio Track of Video using ffmpeg


    A very common use case is that you don't want to waste time using a video editor that requires you to open it up and manually import the video clip and audio clip, then manually delete the old audio track and import the video and new audio. That's too much work and time since we don't want to go through the hassle. ffmpeg is our solution, all we have to do is specify 3 variables and we're done! -i Windows2019-Server-Noaudio.mp4 is our in........

  • apcupsd how to setup and monitor APC UPS units


    It really seems limited in that it can mainly give you the things you would see on the physical unit such as load etc.. wget https://downloads.sourceforge.net/project/apcupsd/apcupsd%20-%20Stable/3.14.14/apcupsd-3.14.14.tar.gz?r=https%3A%2F%2Fsourceforge.net%2Fprojects%2Fapcupsd%2Ffiles%2Flatest%2Fdownload&ts=1598115866 tar -zxvf apcupsd-3.14.14.tar.gz cd apcupsd-3.14.14 [root@somebox apcupsd-3.14.14]# ./conf........

  • How To Get Started on Ubuntu with gpt-2 OpenAI Text Prediction


    apt install software-properties-common add-apt-repository ppa:deadsnakes/ppa apt update apt install python3-pip apt install python3.7 curl gnupg python3.7-dev git ln -s /usr/bin/python3.7 /usr/bin/python3 pip3 install numpy keras_preprocessing curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add - echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........

  • Linux How To Change NIC Name to eth0 instead of enps33 or enp0s25


    Most newer distros inexplicably cause your NIC to have what Icall "random" non-standard name conventions because of systemd. This is a big problem for many people and especially those running servers. Imagine that you have a static IPconfigured for ens33 but then the hard disk is moved to a newer system, the NIC could be anything from ens33 to enp0s1, meaning that manual intervention is required to go and update the NIC config file (eg. /etc/network/interfa........

  • Asterisk Does Not Retry When Authentication Fails


    When authentication times out that is one thing, but when it just fails like below Asterisk by default will not re-register until you the admin reload the sip or asterisk server: voipserver*CLI> sip show registry Host dnsmgr Username Refresh State&........

  • How To Install OpenProject on Centos 7 Step-by-Step Guide


    There are a few caveats that may not be obvious to everyone so I am going to cover them here but keep this in mind before starting. Before starting install epel or you will be missing tesseract: yum -y install epel-release #1) When you specify your SSL certificate with a full path, it really needs to exist where you tell it to (including the default location of /etc/ssl/certs and /etc/ssl/c........

  • Linux How To Add User To Additional Group


    sudo usermod -a -G groupname username It's really simple like above, the -a is for append so that you are not changing their main group, but adding them to another additonal group. Just change "groupname" to your group and "username" to the user you want to be added to "groupname". A common task these days is getting your user access to kvm for virtualization so the KVM/QEMUprocess........

  • Howto Set Static IP on boot in initramfs for dropbear or other purposes NFS, Linux, Debian, Ubuntu, CentOS


    This is only really necessary in the case you don't want DHCP. If you are dealing with an encrypted LUKS server on the internet, you will often want to have a static IP so you know which IP to connect to (or if you have a semi-static IP assigned by DHCP). SET IP Address by /etc/initramfs-tools/initramfs.conf IP Address=192.168.1.27 Gateway=192.168.1.1 Subnet Mask: 255.255.255.0 Hostname=myhome.com IP=192.1........

  • Debian and Netplan


    Create your netplan file vi /etc/netplan/01-netcfg.yaml network: version: 2 renderer: networkd ethernets: ens3: dhcp4: no ........

  • Linux Mint / Ubuntu / Debian Mate Disable Guest Session and Hide Usernames on Lightdm Login screen GUI


    sudo vi /etc/lightdm/lightdm.conf.d/70-linuxmint.conf Change this: [SeatDefaults] user-session=mate allow-guest=false To this: [SeatDefaults] user-session=mate allow-guest=false greeter-hide-users=true greeter-show-manual-login=true To see and apply your changes just restart light........

  • ssh how to connect using a SOCKS 5 proxy with nc and proxycommand


    This is not about using ssh as a proxy, but rather, using a proxy when you are SSHing to another host and using ProxyCommand (where we normally use nc as our proxy tool). In newer versions of nc the syntax has changed to the following: ssh -o ProxyCommand="nc -x 127.0.0.1:1234" %h %p user@host The format must be like above in newer nc versions. Just be sure to change the 1234 to the port of your SOC........

  • Wordpress Reset Blog User Password from MySQL Using Linux Bash and not PHPMyadmin


    The reason we use the command below is because we need the md5sum value hash of the password. This means that we cannot use the md5sum Change "yournewpass" to the pass you want to set echo -n "yournewpass" | md5sum Then you get the md5sum hash of whatever you entered eg. in this case "yournewpass" 5a9351ed00c7d484486c571e7a78c913 ........

  • Linux Console Login Screen TTY Change Message


    This is all controlled by /etc/issue You can basically enter anything in there that you like, but there are preset variables that are mentioned at the end of the page that discuss this. Some examples of /etc/issue: Centos 7: S Kernel r on an m Ubuntu 16.04: Ubuntu 16.04.6 LTS n l You can also insert any of t........

  • MySQL Bash Query to pipe input directly without using heredoc trick


    Most of us know the heredoc method but what if you need a basic query done repeatedly and manually while working from bash? It is a pain to manually type mysql and login each time. With this command below you can semi-automate those queries: echo "use somedb; select * from auctions" | mysql -u root --password="yourpassword" Just modify the above to suit your needs and you can add more queries by adding a sem........

  • CentOS 6 and 7 / RHEL Persistent DHCP Solution


    It is very silly but the default on the ifup-eth script tells dhclient ( the program that obtains a DHCP IPaddress if you have selected DHCPin your ifcfg-eth* config file) to EXIT / QUIT if the first attempt to obtain a lease fails. No amount of dhclient.conf settings will fix this because if dhclient is started with -1 (which it is by default)then dhclient will quit. This is obviously very bad for MOST cases. Say for example you have a power outage or........

  • MySQL Cheatsheet Guide and Tutorial


    Create Database: create database yourdbname; Show All Databases: show databases; Change Database: use mysql; Drop / Delete a MySQL Database: drop database nameofyourdatabase;........

  • qemu-kvm error "Could not initialize SDL(No available video device) - exiting"


    Now older versions of qemu-kvm didn't throw this error say if you just had "-video cirrus" when starting qemu-kvm. But newer versions do care. And this probably only applies to you if you are running from bash/terminal with remote kvm images. What you need to do is remove the "-video" part and just add -vnc :5 eg. this would fix the error: qemu-system-x86_64 -enable-kvm -boot order=cd,once=dc -m 1024 -drive........

  • Wordpress overwrites and wipes out custom htaccess rules and changes soluton


    cat .htaccess RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . index.php [L] I keep reading there is a "# BEGIN WordPress" and a "# END WordPress" in the wordpress htaccess above but there is clearly not. Even more strange is that my permissions are just 444 (read only). so i changed it........

  • Apache htaccess and mod_rewrite how to redirect and force all URLs and visitors to the SSL / HTTPS version


    It is really simple using .htaccess with mod_rewrite. Here is all you need: RewriteCond %{SERVER_PORT} 80 RewriteRule ^(.*)$ https://site.com/$1 [R=301,L] Another more graceful way is to use the %{SERVER_NAME}variable to make it dynamic. Just be careful that the server name will always match what you expect. (eg. if you are doing load balancing or clustering what if the server name may be somethi........

  • Virtualbox vbox not starting


    If you've just installed VBox and it is not starting or working, the most common problem is usually that you don't have your kernel source installed, which means there is no kernel driver for vbox so it can't work. You may get an error that says "Kernel driver not installed" in your Virtualbox. So the first thing you should do is install your kernel source by running this: sudo apt-get install linux-headers-`uname -r`........

  • Bind / named not responding to queries solution


    By default bind will not respond to outside queries for security reasons. In most distributions you will find the default in /etc/named.conf looks like this at the top under options: listen-on port 53 { 127.0.0.1; }; listen-on-v6 port 53 { ::1; }; directory "/var/named";........

  • Linux Mint How To Set Desktop Background Image From Bash Prompt CLI


    The way of doing it in mint is different than gnome and ubuntu. gsettings set org.mate.background picture-filename /path/to/file.jpg *If you try to use the gnome way it will NOT work with Linux Mint: gsettings set org.gnome.desktop.background picture-uri /some/pic.jpg........

  • Linux Mint Mate Customize the Lock screen messages and hide username and real name


    This is a security hole in my opinion and should be plugged by editing the lock screen ui layout: vi /usr/share/mate-screensaver/lock-dialog-default.ui #find these objects and set the visible property to false object class="GtkLabel" id="note-tab-label" object class="GtkLabel" id="auth-username-label> object class="GtkLabel" id="auth-realname-label"........

  • Cisco Unified Communications Manager / CUCM IP 8.6,10,12 Install Error Solution


    Install Errors on Version 12: This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5 on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error. *Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install. What really causes this even though you successfully install........

  • bind / named how to make a wildcard record and retain defined A records


    It is almost as intuitive as we would like it is just a *. So literally: *INA 127.0.0.1 Complete working bind zonefile below: $TTL 86400 @ IN SOA ns.rtt.ca. ns2.rtt.ca. ( 1247605715; Serial &n........

  • Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM


    The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........

  • qemu-kvm qemu-system Image format was not specified for '/mnt/space/cucm12.img' and probing guessed raw. Automatically detecting the format is dangerous for raw images, write operations on block 0 will be restricted. Specify the 'ra


    WARNING: Image format was not specified for '/mnt/space/cucm12.img' and probing guessed raw. Automatically detecting the format is dangerous for raw images, write operations on block 0 will be restricted. Specify the 'raw' format explicitly to remove the restrictions. #you should manually specify the format q........

  • Debian / Mint / Ubuntu net-tools packages provides netstat, ifconfig, route, arp and other classic network admin tools


    The net-tools command brings back all of the oldschool tools that we're used to: /bin/netstat /sbin/ifconfig /sbin/ipmaddr /sbin/iptunnel /sbin/mii-tool /sbin/nameif /sbin/plipconfig /sbin/rarp........

  • Linux bash prompt why does it not show username@host and the current directory?


    Perhaps you've just seen this in the bash prompt: -bash-4.1# Instead of the expected user@hostname# It is probably because you are missing .bash_profile or .bashrc in your home directory Check for yourself: ls -al ~/|grep -E ".bash_profile|.bashrc" -rw-r--r--. 1 root root&nbs........

  • Cisco CUCM Unified Communication Manager Howto Guide and Tutorials


    Install Issues: How to Make CUCM iso /modify to work on non-VMWare machines like QEMU/Xen/OpenStack If you get kernel panic errors in VBOX usually disabling Nested Paging will fix the issue (thanks to Mark). ks_pre.sh error is caused by having the wrong VDX pattern (change it do sd per guide link above) and/or the wrong VMSpecs (Cisco req........

  • ssh reverse proxy to enable remote access behind a LAN and firewall


    So say you are behind a typical NAT/LAN setup whether at home, work or while travelling. What if you have a computer or server that you need to connect to from the outside? Yes you could use a VPN but a quick and dirty, temporary and secure way is to use SSH's Reverse Tunneling Proxy feature. Requirements On the remote ssh server host you need the GatewayPorts option enabled in sshd_config (be........

  • Cisco Router Setup Guide and Tutorial Howto With Commands and Examples


    In most of the Cisco router IOS I find the ports like ge0/0 ge0/1 and ge0/2 or whatever your ports are down. They will not even give you a link light. So one of the first tasks should be getting the port you are working with up. In my case the first goal is often connectivity with the LAN and WAN. LAN = your local area network (eg. in the office/home ) WAN= your ISP/public internet (eg. fiber/cable/dsl/ethernet).........

  • Linux Bash Script To List All Connected IPs and their network name


    for ip in `netstat -nt|awk '{ print $5 }'|cut -d ":" -f 1|tail -n +3|sort|uniq`; do echo $ip;whois $ip|grep -i netname;echo "---------------------------" done 77.88.47.40 netname: YANDEX-77-88-47 --------------------------- 40.77.167.5 ------........

  • Windows Server 2012, 2016, 2019 How To Install and Missing Disabled Telnet Client


    By default telnet is not enabled or installed on the latest Windows servers so you'll get an error saying: telnet is not recognized as an internal or external command dism /online /Enable-Feature /FeatureName:TelnetClient ........

  • LUKS Hard Drive Encryption on Linux Mint Ubuntu Debian etc how to mount encrypted hard drive


    The key thing here is to know the actual partition that is encrypted. Often in Linux Mint's installer that ends up being partition 5 or /dev/sda5 sudo cryptsetup luksOpen /dev/sda5 anynamehere You will then be prompted for your irrecoverable passphrase: Enter passphrase for /dev/sda5: If all goes well it won't say anything further. If it says ""No key available with this passphr........

  • Proxmox Breaks Storage/LVM Backing If Killing QEMU-IMG


    I tried to stop a qemu-img copy or clone and it broke everything. It was fine to "stop" it from the GUI but a process still persisted so I killed the relevant qemu-img and the kernel went crazy. It also may not have helped that I tried to lvremove a different volume (an unused disk). But either way it breaks LVM (you cannot even run lvdisplay) so a reboot is necessary. Jan 17 06:45:21 testserver kernel: [ 5680.439337] systemd-udevd D 0&nbs........

  • Centos 6 / 7 / 8 How To Change Default nameservers in /etc/resolv.conf when using DHCP / dhclient


    First we need to create dhclient.conf if it doesn't exist or edit it: vi /etc/dhclient/dhclient.conf #add this line at the top add the IPs as commas they will be the highest priority nameservers and whatever your ISP gives you will be used after these one (good for DNS backup) prepend domain-name-servers 127.0.0.1,10.10.25.8; After you restart your network or run dhclient again you should see the contents of........

  • Why SMART is not smart at all and doesn't properly predict disk errors that cause a kernel panic or crash


    Before getting into the output here is my typical experience with SMART, there is what I call a "bad disk" with pending and uncorrectable sectors that cannot be reallocated. It has caused a kernel panic and system crash repeatedly as we can see from the logs. But SMART says it has "PASSED" its self assessment. SMART is still useful to me but it is more about looking at Current_Pending_Sector. Any time I have had anything but 0 for that attribute it........

  • Python and BeautifulSoup4's BS4's Decompose Method To Remove Unwanted Inner Tags


    < a href="/Products/MX72244"> < span class="c-shca-icon-item__body-name-brand"> ADATA < / span> &nbs........

  • systemd management using systemctl and journalctl to check systemd logs


    systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system. The key commands or arguments you will use with systemctl are the following: Unit Commands: list-units [PATTERN...] List loaded units &nbs........

  • AMD Set Fan Speed and Other Powerplay Memory/CPU Timings with a Linux script


    You can do other things but this particular script is just to set all AMD cards to 80% fan speed (remember this script needs to applied everytime you reboot). You could set it is a cron or just throw it into /etc/rc.local basepath=/sys/class/drm for hwmon in `ls -1 /sys/class/drm|grep card[0-99]$`; do echo card=$hwmon; hwmonname=`ls $basepath/$hwmon/device/hwmon|grep hwmon[0-99]` hwmonpath=$basepath/$hwmon/device/hwmon/$hwmonname echo "ec........

  • genisoimage errors with long filenames and deep directory structures


    You'll have to violate the iso9660 standards but it is necessary if you want to preserve your filesystem and filenames and shouldn't be an issue as long as you are using a modern OS like Linux. genisoimage -o Backup-Myfiles.iso -r -J -joliet-long /some/path/ You will get errors like below (even enabling joliet-long didn't help) genisoimage: Error: /some/filename.pdf have the same Joliet name Joliet tree sort failed. The -joliet-lo........

  • HP DL385 G7 Linux BIOS Update Flash


    wget https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe --2018-08-16 05:11:16-- https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe Resolving downloads.linux.hpe.com (downloads.linux.hpe.com)... 15.249.152.85 Connecting to downloads.linux.hpe.com (downloads.linux.hpe.com)|15.249.152.85|:443... connected. HTTP request sent, awaiting response... 200 OK Length: 1525561 (1.5........

  • Firefox An error occurred during a connection to some-ip-or-domain. SSL peer reports incorrect Message Authentication Code. Error code: SSL_ERROR_BAD_MAC_ALERT Solution


    An error occurred during a connection to some-ip-or-domain. SSL peer reports incorrect Message Authentication Code. Error code: SSL_ERROR_BAD_MAC_ALERT The page you are trying to view cannot be shown because the authenticity of the received data could not be verified. Please contact the website owners to inform them of this problem. **Solution** Go to about:config........

  • VMWare vSphere 6.7 Errors Solution 503 Service Unavailable (Failed to connect to endpoint:


    503 Service Unavailable (Failed to connect to endpoint: [N7Vmacore4Http20NamedPipeServiceSpecE:0x00005556ba09c070] _serverNamespace = / action = Allow _pipeName =/var/run/vmware/vpxd-webserver-pipe) 503 Service Unavailable (Failed to connect to endpoint: [N7Vmacore4Http16LocalServiceSpecE:0x00007fd26000b240] _serverNamespace = /ui action = Allow _port = 5090) Errors like the above are usually because there is an issue with your vSphere or more commonly it i........

  • Linux bash shell doesn't show username, hostname or current path fix solution


    Usually this is because when you created your user you added a user but didn't create their home directory and/or for some reason your .bashrc and .bash_profile in ~ (home) is broken/missing. In your home just create the following files with the following content to solve it: .bashrc and .bash_profile. To apply it just relogin/start a new bash session # .bash_profile # Get the aliases and funct........

  • PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/geoip.so' - /usr/lib64/php/modules/geoip.so: undefined symbol: GeoIP_country_code_by_name_v6 in Unknown on line 0


    PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/geoip.so' - /usr/lib64/php/modules/geoip.so: undefined symbol: GeoIP_country_code_by_name_v6 in Unknown on line 0 Solution: Edit geoip.ini vi /etc/php.d/geoip.ini Comment out the .so like so: ;extension=geoip.so service httpd restart........

  • VMWare ESXi 6.7 SSH/PowerShell CLI Commands


    [root@localhost:~] BootModuleConfig.sh echo host-ind nfcd........

  • Debian Mint Ubuntu compiling xmr-stak


    sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........

  • Linux How To Rename Files


    To remove all spaces from all files in the current directory linux rename remove spaces rename "s/ //g" * how to replace part of the text with another (it is almost like using sed): rename s/"Screenshot at 2019-04-22 "/"AC97-Windows-InstallSolution"/g * The first part "Screenshot at 2019-04-22" is what we're looking for The........

  • [warn] VirtualHost 10.2.5.101:443 overlaps with VirtualHost 10.2.5.101:443, the first has precedence, perhaps you need a NameVirtualHost directive


    [root@thetor2017 conf]# service httpd restart Stopping httpd: [ OK ] Starting httpd: WARNING: MaxClients of 3000 exceeds ServerLimit value of 300 servers, lowering MaxClients to 300. To increase........

  • PayPal IPN Failed "result: IPN Handshake Invalid"


    This is often the result of PayPal's "item name" or another name having invalid characters or not supporting Unicode. 173.0.81.1 - - [17/Jul/2018:13:39:45 -0400] "POST //modules/gateways/callback/paypal.php HTTP/1.1" 406 - "-" "PayPal IPN ( https://www.paypal.com/ipn )" A good clue is if you check the debug output of the IPNand find a mandatory column empty. ........

  • VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI


    #mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........

  • OpenVPN auth-user-pass-verify ENV script error


    Starting with newer versions of OpenVPN Ibelieve 2.2+ you need to have "script-security 3" set or you can't execute a third party script. Prior to that you could also use the auth-user-pass-verify like this: auth-user-pass-verify ./validate.pl "$username $password $ip" via-env Options error: the --auth-user-pass-verify directive should have at most 2 parameters. To pass a list of arguments as one of the paramete........

  • not allowed to execute '/usr/bin/apt-get install eclipse' as root linux sudo user permisson issue and solution


    This is most likely to happen on a normal GUI system like Ubuntu or Linux Mint. If you or the user is meant to have sudo / root privileges it is as simple as editing the following files: Now assume your username is "iamtheuser" vi /etc/group adm:x:4:syslog,iamtheuser sudo:x:27:anotheruser,iamtheuser Find the above lines and add a comma and "ia........

  • Database Error One or more of the WHMCS database tables appear to be either missing or corrupted. Please check and repair. - WHMCS Solution


    Database Error One or more of the WHMCS database tables appear to be either missing or corrupted. Please check and repair. This error can be misleading especially if you know you are using a known good backup or restoration of the WHMCS database. The error can also be that the user lacks permissions to read and write to the database. To check to this in MySQL shell: GRANT read,write to dbusername@localhost on dbna........

  • postfix errors fatal: no SASL authentication mechanisms /usr/libexec/postfix/smtpd: bad command startup -- throttling solution


    Jul 3 22:12:17mailserver postfix/smtpd[6195]: fatal: no SASL authentication mechanisms Jul 3 22:12:18mailserver postfix/master[4881]: warning: process /usr/libexec/postfix/smtpd pid 6195 exit status 1 Jul 3 22:12:18mailserver postfix/master[4881]: warning: /usr/libexec/postfix/smtpd: bad command startup -- throttling This only ever happens in my experience when the authentication method is actually Dovecot. Usually the problem........

  • named[1525]: error (broken trust chain) resolving 'min-api.cryptocompare.com/A/IN': 173.245.58.78#53 solution


    So you restarted your router/dhcpd server or for some other reason you wonder why DHCP is not working on any of your clients?You go and check that named is in fact running fine. But then you check /var/log/messages and see this error for everything hostname: named[1525]: error (broken trust chain) resolving 'min-api.cryptocompare.com/A/IN': 173.245.58.78#53 I've only ever seen this when the time on the server was off. It........

  • Linux Ubuntu Mint Debian cannot play xvid,x264,mp4 or any videos codec issue - xplayer Could not initialize supporting library.


    In xplayer Iget the following error "Could not initialize supporting library.". It actually looks more like a gstreamer issue. For those wondering what the default video player is called it is "xvid" and not "totem" anymore like previous versions. Basically it looks like some codecs are missing when I uninstalled another program it uninstalled other programs and codecs that it shouldn't have. I've tried installing all the gstre........

  • How To Turn Any .iso file into a bootable USB drive


    This works for almost all ISO's Ifind (at least Linux based): sudo dd if=CentOS-6.9-x86_64-minimal.iso of=/dev/sdg bs=20M 20+1 records in 20+1 records out 427819008 bytes (428 MB) copied, 118.233 s, 3.6 MB/s Of course change the .iso filename above and the /dev/sdg to your desired USB drive!........

  • sudo: unable to resolve host


    sudo: unable to resolve host yourhostname No clue why sudo is doing that when running. Solution Check /etc/hosts You will probably find that it doesn't contain "yourhostname" for 127.0.0.1 Just update the hostname or add a field for your hostname like this: 127.0.0.1 yourhostname ........

  • Installing SSL Certificate with Chain Intermediary CA File


    Some of the cheaper or newer SSL suppliers will require this to work properly (otherwise you may be prompted that the cert is invalid when it's not the case but it will certainly scare off your users!). In the Apache vhost conf for the domain here is what you add: SSLCACertificateFile /path/to/your/cafile.pem Here is a full example of an SSL Vhost config in Apache using a CA Certificate file ........

  • How to start screen in bash script or from /etc/rc.local on startup as a specific user


    It takes some tinkering the main thing is that the "-dmS" flag allows screen to start without a session which of course sudo won't have. solution: /usr/bin/sudo -u user /usr/bin/screen -dmS nameyouchoose /script/start.bash this doesn't work at all: /usr/bin/sudo -u user "/usr/bin/screen /script/s........

  • Linux How To Clone One System Harddrive to another remote system


    The easiest way is to use SSHand DD or a combination of netcat. SSHwill be a little slower due to encryption but is the most secure way (on two older systems the average clone speed is about 40-50MB/s). This is also OS independent as it doesn't matter what the source OS is because you are literallly cloning the drive so you retain the partition table and settings. Clone HDD using SSH and DD........

  • MySQL Adding New Field to Existing Database Table


    ALTER TABLE existingtable ADD newfieldname VARCHAR(255);........

  • mysql how to reset passwords with a few commands


    The commands below will help you reset any mysql user password. use mysql; update user set password=PASSWORD('thenewpass') where User='theusername'; flush privileges; The first line says to use the "mysql" database which contains all the user info. the second update line sets the new password "thenewpass" for the u........

  • PHP geoip.so fatal error Solution


    PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/geoip.so' - /usr/lib64/php/modules/geoip.so: undefined symbol: GeoIP_country_code_by_name_v6 in Unknown on line 0 Remove the GEOIP from PHP: php71w-pecl-geoip-1.1.1-1.w6.x86_64 PHP Fatal error: PHP Startup: apc_shm_create: shmget(0, 67108864, 914) failed: Invalid argument. It is possible that the........

  • How To Create Apache htpasswd file


    This just simply outputs what you need a username and password that can be used to authenticate from .htaccess htpasswd -nb user password user:Gnb6uE9Lp4gt2 If you want to write it straight to a file htpasswd -cb /tmp/somefile.pw user password How To Use This In .htaccess AuthUserFile /tmp/somefile.pw AuthName GetLost!! AuthType B........

  • Linux last command show login by IP instead of hostname


    In the "last" command in Linux by default it will show the information with the hostname (not very useful at all especially since it normally truncates long hostnames). To get last to show the IP address use this: last -i The -i makes it show the numeric IP instead of hostname.........

  • pcimodules and lspci not working alternative solution


    pcimodules no longer works it produces nothing probably because the format of /sys/bus/pci is different. lspci -k doesn't work on older lspci versions. pciutils can be compiled but it won't work if you have an old system and compile on a newer glibc. iteriate through /sys/bus/pci/devices/*/modalias cat /sys/bus/pci/devices/*/modalias pci:v00008086d00001237sv00000000sd00000000bc06sc00i00 pci:v00008086d00007000sv0000000........

  • M2Crypto.SSL.Checker.WrongHost: Peer certificate subjectAltName does not match host, expected fedora-archive.ip-connect.vn.ua, got DNS:mirror.ip-connect.vn.ua


    You are using Centos 5 which is deprecated so nothing in yum will work until you follow this post to use the vault: http://realtechtalk.com/Centos_59_Working_Vault_Repo_file-1921-articles yum update Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * epel: fedora-archive.ip-connect.vn.ua Traceback........

  • Linux Mint/Ubuntu/Debian apt how to downgrade a package


    First of all check to see which version if any you have available for a downgrade: apt-cache showpkg packagename Downgrade/Install old package: apt-get install package=version Example apt-cache showpkg caja Package: caja Versions: 1.10.3-1+rafaela (/var/lib/apt/lists/packages.linuxmint.com_dists_rafaela_import_binary-amd64_Packages) (/var/........

  • Ubuntu Linux Mint How To Exclude Stop Package from being Upgraded or Installed


    In Debian/Ubuntu this is called "holding". To hold/exclude a package from being installed or upgraded: sudo apt-mark hold packagename To allow the upgrade/installation unhold: sudo apt-mark unhold packagename........

  • ffmpeg trouble concatenating similar but different files


    When things go wrong your video is basically unplayable or the first video plays fine and then freezes when moving on to the next. Generally if both videos weren't produced with the exact 100% same settings you will have issues. You can try the basic concat but it often won't work right. Solution for me: My example uses 3 videos in total so "n=3" and a=1 to include audio. ffmpeg -threads 12 -i file1.mp4 -........

  • Centos 7 How To Change Hostname


    Some guides still use the old Centos 6 style (do not use /etc/sysconfig/network). In Centos 7 the file is /etc/hostname echo "HOSTNAME=yourhostname.com" > /etc/hostname........

  • USB 3.0 External HDD Enclosure Seagate UAS problems - [sdd] tag#1 CDB: Write(16) 8a 00 00 00 00 01 70 04 08 68 00 00 00 08 00 00


    This is a 8TB Seagate external USB 3.0 device apparently newer kernels use a module called "UAS" instead of "USB Storage" which causes issues as a lot of devices are not properly supported in UAS mode by the kernel driver. The solution some say is to disable UAS specifically for your USB device but I'd rather just disable UAS altogether. Solution blacklist UAS: *do not do this it does not work and just causes your USB 3.0........

  • Centos 7 Cudaminer Nvidia setup guide


    I am using a GTX 1060 but replace the download for the driver with the correct/current version for your particular card by visiting: http://www.nvidia.com/Download/index.aspx?lang=en-us yum install automake curl openssl-devel libcurl-devel gcc gcc-c++ yum -y install kernel-devel-`uname -r` yum -y install unzip #the........

  • rsync run as root sudo without password


    This is a common issue, what if a issue shouldn't have root but you want to use that user to make a full backup of a system? They of course need root access. You can actually just give them passwordless sudo access to rsync in /etc/sudoers: sudo vi /etc/sudoers yourusername ALL = NOPASSWD: /usr/bin/rsync Here is how you would execute rsync: The key thing for the remote host is to........

  • Apache SSL very slow response with Firefox Freezes/Loads Very slow when checking self-signed SSL certificate


    I was sure this was a Centos bug with OpenSSL, Apache, MySQL or even PHP. I tried everything but nothing helped. One clue is that if you check the Apache logs you will see nothing in the access logs until minutes later (this means Firefox has not even passed your request to the remote Apache/htttpd server). When even accepting the invalid certificate message that would show up minutes later when trying to "View the Certificate" Firefox would freeze. This bu........

  • Track 01: 34 of 1726 MB written (fifo 100%) [buf 99%] 3.6x.Errno: 5 (Input/output error), write_g1 scsi sendcmd: cmd timeout after 1.897 (40) s CDB: 2A 00 00 00 44 A9 00 00 1F 00 resid: 6144 cmd finished after 1.897s timeout 40s write track da


    These errors believe it or not are simply because of not being the root user or running with sudo! However if you didn't know to try as root you'd think there was a problem with your burner or disc Essentially it looks like without root you cannot send the required scsi commands to continue writing. Ithink cdrecord should have built-in tests or safeguards to see if it has the permissions to run the required commands. I guess for more advanced users the idea is simila........

  • xdebug easiest howto get going


    Just make sure you have php-xdebug installed and edit your php.ini: [xdebug] xdebug.profiler_enable = 0 xdebug.profiler_enable_trigger = 1 xdebug.profiler_output_dir = "/tmp/xdebug/" xdebug.output_name = "cachegrind.out.%t-%s" Also make and set permissions on /tmp/xdebug: mkdir /tmp/xdebug chmod 777 /tmp/xdeb........

  • Text Editors - Top Linux Ubuntu/Debian/Mint Options


    1.) gedit/pluma both very good the only thing I wish is that there was an autosave for unsaved documents! The only other competitor which is similar but I prefer less is kwrite (although I think kwrite may have proper autosave) pluma seems to be a renamed gedit yet gedit is still installable on Linux Mint) ........

  • Centos 7 Migration Guide from Centos 6


    Centos 7 is no cakewalk, there are many fundamental features and basic utilities that are missing or even completely renamed or different! Another shocking thing is to check your NIC it is set by default to not turn on when booting! And by the way there is no more standard eth0 the NIC convention is now "enp0s3" vi /etc/sysconfig/network-scripts/ifcfg-enp0s3........

  • ecryptfs errors


    ecryptfs-mount-private Enter your login passphrase: Inserted auth tok with sig [ee16d84] "into the user session keyring mount: No such file or directory" [ 156.118113] ecryptfs_mount: kern_path() failed [ 156.118431] Reading sb failed; rc = [-2] [ 164.233055] traps: mate-notificati[3472] trap int3 ip:7f43d7002c13 sp:7fff162c6600 error:0 [ 166.017061] ecryptfs_mount: kern_path() failed........

  • mdadm and lvm how to completely disable and remove vg/pv/lv


    In short the solution is just to use vgremove for the actual /dev/mapper device: vgremove /dev/mapper/backups-backuplv box mnt # mdadm --manage /dev/md8 --stop mdadm: Cannot get exclusive access to /dev/md8:Perhaps a running process, mounted filesystem or active volume group? box mnt # lv lvchange lvconvert lvcreate l........

  • mdadm frozen and doesn't realize array is dead/missing failed due to unplugged drives


    This was a surprising bug but I unplugged all drives for an array md127. At first it was just 1 drive and mdadm seemed to notice this. I unplugged the second drive taking the array offline but mdadm did not realize it was offline and still showed a non-existent disk as being part of it. This created problems trying to unmount it or even to stop this array with mdadm freezing. As for how to fix it I can only think of making sure you are not in a mounted path of........

  • Unable to mount location Failed to retrieve share list from server: No such file or directory solution


    Cannot even "Browse Network" when clicking on "Windows Network" Unable to mount location Failed to retrieve share list from server: No such file or directory logs: [2017/02/14 00:16:44.271314, 0] ../source3/nmbd/nmbd.c:58(terminate) Got SIGTERM: going down... [2017/02/13 17:35:41.797944, 0] ../lib/util/become_daemon.c:124(daemon_ready) &........

  • PayPal Subscription Howto Creation Automatic Payments Manual


    An easy way to pay companies and friends/family since PayPal does not have an option when sending money to make it a subscription: "business" = The e-mail or PayPal ID of the person/organization to pay to. a3 The recurring amount "eg. 115" will be 115 USD p3 The time period (eg. 2) t3 Unit of time period m=monthly,w=weekly,y=yearly item_name = "the note/product service reason you are paying ha........

  • ADATA SU800 256GB 3D NAND Flash SSD Test & Review


    I keep reading these drives are slower, but they are cheap and still SSDand work very fast for my needs. As you can see the sequential read is 481-491MB/s, if I put them in MDADM RAID10 mode (normal RAID1) they should give me well over 900MB/s and with redundancy and being very cheap for what they offer. [1232206.315622] scsi 8:0:1:0: Direct-Access ATA ADATA SU800&........

  • mcp55 NIC not working at boot on Centos 6.6-6.8


    forcedeth 0000:00:08.0: irq 25 for MSI/MSI-X forcedeth 0000:00:08.0: eth0: MSI enabled forcedeth 0000:00:08.0: eth0: no link during initialization ADDRCONF(NETDEV_UP): eth0: link is not ready forcedeth 0000:00:08.0: eth0: link up ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Dec 1 18:21:32 box15 kernel: forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64. Dec 1 18:21:32 box15 kernel........

  • OpenVZ Solution CPT ERR: c02fa000,73 :CPT: lock fd is closed incorrectly: 1 and vps-net_add ERROR: Unable to add route ip route add 192.168.5.2 dev venet0


    The only solution after trying many suggestions was to simply restart the "vz" service (definitely not preferable). Even doing an ifdown and ifup for venet0 did not help. ifup venet0 Bringing up interface venet0: Configuring interface venet0: net.ipv4.conf.venet0.send_redirects = 0 RTNETLINK answers: Network is down Some errors from log: CPT ERR: d2dc60........

  • Apache Log Error Message when starting


    Usage: geoiplookup [-h] [-?] [-d custom_dir] [-f custom_file] [-v] [-i] [-l] Usage: geoiplookup [-h] [-?] [-d custom_dir] [-f custom_file] [-v] [-i] [-l] grep: Address: No such file or directory grep: not: No such file or directory grep: found: No such file or directory sh: -c: line 1: syntax error near unexpected token `|' sh: -c: line 1: `|cut -d ',' -f 2' ........

  • blocked for more than 120 seconds issues with iowait and timeout on Live Linux distribution while writing to physical disk


    This happened while an mdadm array was syncing, all access from writing a new blank file to opening a small .txt file was very slow: [222117.312078] kjournald starting. Commit interval 5 seconds [222117.685060] EXT3-fs (md0): using internal journal [222117.685096] EXT3-fs (md0): mounted filesystem with ordered data mode [222122.376847] kjournald starting. Commit interval 5 seconds [222122.602825] EXT3-fs (md2): using internal jour........

  • Apache Centos Stopping httpd: [ OK ] Starting httpd: [Wed Jun 29 19:29:44 2016] [warn] _default_ VirtualHost overlap on port 80, the first has precedence [Wed Jun 29 19:29:44 2016] [warn] _default_ Virtual


    Stopping httpd: [ OK ] Starting httpd: [Wed Jun 29 19:29:44 2016] [warn] _default_ VirtualHost overlap on port 80, the first has precedence [Wed Jun 29 19:29:44 2016] [warn] _default_ VirtualHost overlap on........

  • Cannot Read License File cPanel Solution


    This can happen because port 80 is not open, or your license has expired and/or your IP is out of date and also if the license server itself from cPanel is having issues. In most cases as long as you have a valid license the following command will solve it: /usr/local/cpanel/cpkeyclt Updating cPanel license...Done. Update succeeded. Building global cache for cpanel...Done Cannot........

  • openvpn 2.3.10-1.el6 issues auth-env does not work correctly for auth-user-pass-verify


    openvpn 2.3.10-1.el6 issues in the .conf auth-user-pass-verify "passwordcheck $username $password $untrusted_ip" via-env auth-env does not work correctly in OpenVPN 2.3: Sat Apr 23 02:30:22 2016 - $username - $untrusted_ip - login failure But OpenVPN 2.2 does work as expected. It could be that the specified script automatically receive........

  • Apache Vhost HowTo Serve Same Content using a different domain and IP


    There are a few ways of doing this and all basically involve using the reverse proxy or "ProxyPass" feature of Apache to accomplish it. 1.) Create a normal vhost and simply symlink the root directory of the site you want to mirror. Eg. originalsite.com and newsite.com /vhosts/originalsite.com/httpdocs You would symlink like this: ln -s /vhosts/originalsite.com/httpdocs vhosts/originalsite.com/........

  • Check Linux Ubuntu/Debian/Mint Version from Command Line


    To check the version of Ubuntu just use the lsb_release command as shown below and you will be able to see the exact Ubuntu version you have installed. lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 14.04 LTS Release: 14.04 Codename: trusty........

  • Debian Ubuntu Mint Samba Share config file location


    /var/lib/samba/usershares But note that it is just simple file sharing if you need directory mask, create mask etc... you still need to edit the smb.conf file to create your share. Here is an example file: comment= usershare_acl=S-1-1-0:R,S-1-22-1-1000:F guest_ok=y sharename=BabyPhotos........

  • Debian Linux Ubuntu Mint connect to pptp from terminal bash shell


    apt-get install pptp-linux echo "yourvpnusername * yourpasspass *" >> /etc/ppp/chap-secrets vi /etc/ppp/peers/provpnaccounts.com enter (ignore the lines): ============ pty "pptp server.provpnaccounts.com --nolaunchpppd" name testuser #remotename PPTP require-mppe-128 file /etc/ppp/options.pptp ==========........

  • linux bash mass rename tool Centos/Debian/Ubuntu


    Say you have a bunch of files like this: file-01.jpg file-02.jpg ............... What if you want to mass rename them? the rename tool can work just like sed For Debian based distros: Note "file" is what we search for and "newname" is what we replace it with, so substitute according to your requirements. rename s/file/newname/ name-file-*.jpg For R........

  • Centos 6 how to guide convert LVM non-RAID into mdadm 1/10 RAID array live without reinstalling


    Here is the scenario you or a client have a remote machine that was installed as a standard/default minimal Centos 6.x machine on a single disk with LVM for whatever reason. Often many people do not know how to install it to a RAID array so it is common to have this problem and why reinstall if you don't need to? In some cases on a remote system you can't easily reinstall without physical or KVM access. So in this case you add a second physical or disk or already ha........

  • Linux sudo config sudoers to run command without a password howto


    Before reading on remember to put the line at the bottom of /etc/sudoers as from experience what happen is that other rules cancel out what you have added. If your sudoers setup is correct it will work immediately upon saving without requiring a reboot. Edit /etc/sudoers yourusername ALL = NOPASSWD: /path/to/command *Once again remember the above should be on the bottom of the sudoers file or........

  • bash script get directory location and path of script howto tutorial


    So the situaton is this, you depend on things being relevant to where your bash script is and to be safe you want it to be dynamic (eg. do not hard code that we switch to /abc/dir but rather detect where script.sh is located). scriptlocation="$( cd "$( dirname "${BASH_SOURCE[0]}" )" && pwd )" The path is then contained the the variable "scriptlocation" so you can cd to it in your script etc............

  • Centos/obfsproxy errors


    I never did get it working, it is too bad as obfsproxy should really be an option and integrated into the OpenVPN client and server or something similar: yum -y install python-pip python-devel No package python-pip available. #install the EPEL repo python-pip install obfsproxy python-pip install obfsproxy -bash: python-pip: command not found pip install obfsproxy &........

  • rm how to delete a file with -- 2 leading dashes


    rm -- --filename Ironically if the solution is two leading dashes as shown above but this applies for other stubborn file names.........

  • bash string substitution


    so in this case we have files named like this: track01.cdda.wav.mp3 track06.cdda.wav.mp3 track11.cdda.wav.mp3 track02.cdda.wav.mp3 track07.cdda.wav.mp3 track12.cdda.wav.mp3 track03.cdda.wav.mp3 track08.cdda.wav.mp3 track13.cdda.wav.mp3 track04.cdda.wav.mp3 track09.cdda.wav.mp3 track05.cdda.wav.mp3 track10.cdda.wav.mp3 but we want to rename them so they are like "05.........

  • KVM/QEMU how to boot from direct kernel vmlinuz and initrd with networking


    Thsi is very handy when doing your own kernel development. -m specifies how much ram (in the example it is 768MB) -kernel specifies the path to the kernel file -net tap,ifname=tap1,script=no (the ifname=tap1 is what you need to change and setup manually). *Run "tunctl -b" to create a tap device and use the one it gives you for ifname= Enable networking to the outside like this: *Note we assume that your bridge is br0 i........

  • Samsung Printer Password Login to change settings CLP


    First of all to find your IP you can hold the "X" button for a few seconds and it will print out the DHCP IP. Another way to find the IP that I prefer is to login to your router or switch and find a hostname that says something like "SEC001599CD2948" which will be your Samsung printer (at least for the C3xx or C4xx series of Samsung printers). The login and password for Samsung Syncthru Webservice:........

  • Postfix Errors & Solutions "unprivileged": bad value: "???" - bad transport type:


    Aug 25 16:43:24 evohostingtor postfix/master[19471]: fatal: /etc/postfix/master.cf: line 24: field "unprivileged": bad value: "???" Solution: I had the wrong thick dashes when c&ping (just retype them with your keyboard) Aug 25 16:47:10 mailbox postfix/master[24498]: fatal: /etc/postfix/master.cf: line 25: bad transport type: syslog_name=postfix/auth-cleanup auth-cleanup unix n - - - 0 cleanup #-o syslog_name=postfix/........

  • Postfix how to secure outgoing authenticated e-mails for privacy and hide the IP address, mailer and other things


    The most common solution is to use the /etc/postfix/header_checks but this is a big problem. Why is header_checks a problem? Because it does it to all mail whether incoming or outgoing and whether authenticated or not. We of course want as much header information for incoming as we can get for many reasons but many organizations want to secure and make their mail clients as secure as possible. I adapted this solution to the client's custom config, they are configur........

  • PayPal subscriptions automatically cancelling after creation of profile


    There is a weird quirk with how this works, but there is a variable called "src" that defaults to 0 or disabled if not specified as 1. The default 0 means not to recur billing on a subscription.  It's too bad it's not more obvious anywhere nor is there an explanation or warning during payment or after to both the seller and buyer. Here's a proper subscription code example that does recur and does not cancel........

  • 2CO/2Checkout how to create recurring payment subscription button dynamically


    It was hard to find this as I find most online payment processors don't just put the basic information in plain view. Remember to set your sid (your seller id). The below can easily be turned into a scripted PHP template to integrate into your own custom or existing payment solution. http://help.2checkout.com/articles/How_to/How-to-Sell-Recurring-Products-with-2Checkout/........

  • CPanel Link to all of the command line options


    CPanel says you can access 98% of the functions through CLI which experienced Unix/Linux admins prefer for simplicity and for scripting.  I've never found CPanel easy to use from the admin panel, it seems everything is hard to find and a simple task becomes a series of hunts. So for people like me here's the list: http://cpanel.net/system-administrators/command-line-scrip........

  • Ubuntu Linux Slow/Delayed SSH ping response Solution


    I've only ever seen this in Ubuntu for some reason and it is because of the /etc/nsswitch.conf settings. So the issue is that if the hostname's reverse DNS cannot be found that you need to go back to DNS which was not the default in this nsswitch.conf file for some strange reason. Edit /etc/nsswitch.conf and replace your "hosts" line with this: #hosts: files dns mdns4_minimal [NOTFOUND=return] mdns........

  • Wordpress Security Hole, Plug it by manually installing themes and plugins


    It's always bothered me how Wordpress basically forces the user to provide their hosting credentials to install themes and plugins. How do know for sure the data is not being saved, intercepted and being provided backdoor access to the NSA or other agencies or even just being misused by others with access? Here's how to close the security hole above and if you're already given Wordpress your credentials make sure you change everything associated it with it. Eg. change your........

  • Howto Convert Xen Image to KVM


    #count=10000 makes an image of 10000MB make sure your image is at least the same as your existing dd if=/dev/zero of=yourimage.img bs=1M count=10000 # losetup -fv newimage.raw # fdisk -cu /dev/loop0 # kpartx -a /dev/loop0 # dd if= of=/dev/mapper/loop0p1 # e2fsck -f /dev/mapper/loop0p1 # resize2fs /dev/mapper/loop0p1 # a lot of guides tell you to edit /etc/fst........

  • cPanel Find/Set Main DNS Servers for Template Howto


    Go to: "Server Configuration" -> Basic cPanel & WHM Setup Scroll to: "Nameservers" (at the bottom) From there you can set the names of the nameserver and their IPs. It's very weird and confusing that nothing under IP Functions/DNS has or links to this.........

  • Asterisk iptables block bruteforce attacks howto with fail2ban


    yum -y install fail2ban vi /etc/fail2ban/jail.conf [asterisk-tcp] enabled = true filter = asterisk action = iptables-multiport[name=asterisk-tcp, port="5060,5061", protocol=tcp] sendmail-whois[name=Asterisk, dest=you@example.com, sender=fail2ban@example.com] logpath = /var/log/asterisk/messages maxret........

  • CPanel Log File Locations for access_log,error_log, mysql


    All Errors (CPanel does not report by domain, but puts everything in a single log which Ithink is a bit silly and annoying): /usr/local/apache/logs/error_log Access_Logs They are found within the home directory of the site user eg.: /home/admin/access-logs/yoursite.com MySQL Logs /var/lib/mysql/yourhostname.err........

  • bash Linux basename and directory name, get the actual directory and file


    Example: basename /var/log/messages messages As shown above the "basename" utility gives you the end filename separately. dirname /var/log/messages /var/log As shown above the "dirname" utlity gives you just the utility even if you pass it a specific file. The above two utilities are very helpful in Bash scripting when working with files and directories co........

  • Apache SNI is not needed what is the issue?


    Iread this article and still don't understand the issue. If I understand correctly the client negotiates after the first SSLconnection and then gets the correct hostname and thus correct certificate. http://wiki.apache.org/httpd/NameBasedSSLVHostsWithSNI To their credit I know I'm not using SNIbecuase Iget this message in the Apache log :) [warn] Init: You should not use name-based virtual hosts in conjunction with SSL!! B........

  • Linux create htaccess file with username and password


    htpasswd -b -c filename username "password" -b = take the password that we specify in the command (don't prompt for it) -c = create the filename username=username password=password (I use quotes because it breaks if you use special characters)........

  • Dell Perci 6/i Firmware Upgrade Guide Tutorial


    One thing to remember is that you need MegaCli to do the flashing. You also need the correct file,I tried at least 2 different Perc 6 firmwares from Dell that kept getting rejected as corrupt by MegaCli(they were really the wrong version). I have an external PCI-E Dell 6 Perc/I butI chose images from the 'Integrated" on motherboard version as it was allI could find. They are different, and below is my first time finding success.........

  • LSI MegaRAID Adventures, Guide and HowTo


    LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........

  • CPanel How To Create/Edit Default Nameservers


    CPanel ->Basic cPanel &WHMSetup At the bottom you'll see them, set the nameservers you want to use and the corresponding A record if needed. Then all new domains will use those settings/nameservers. It's strange that there's no section for this specifically.........

  • GoDaddy How To Register and Create/Use Your Own DNS Name Servers


    http://support.godaddy.com/help/article/668/registering-your-own-nameservershosts?pc_split_value=1 Log in to your GoDaddy Account. Click on "My Account" at the top left. Click on "Domains". Click on the "Launch" button for the domain you want to create the nameservers for. Find........

  • yum update error


    yum update error Traceback (most recent call last): File "/usr/bin/yum", line 29, in ? yummain.user_main(sys.argv[1:], exit_code=True) File "/usr/share/yum-cli/yummain.py", line 229, in user_main errcode = main(args) File "/usr/share/yum-cli/yummain.py", line 145, in main (result, resultmsgs) = base.buildTransaction() &nbs........

  • bash how to read a single line or filenames with spaces solution


    This happens all the time, you are reading from a textfile which has spaces eg: datainfo 00 datainfo 11 If you do loop on it like this: for info in `cat $file`; do echo "info=$info" done It will treat datainfo and 00 as two separate lines: info=datainfo info=00 Obviously that's not what we want and there are many weird solutions in bash bu........

  • stat=Deferred: 451-Non-existent domain mailserver.com


    Jul 11 15:20:58 tor sendmail[9617]: r6AKjOD07: to= mailserver.com was the hostname of the server, sendmail sends this by default and many mailservers will reject mail to a hostname that does not resolve or exist. The easiest way is just to change the hostname and make sure it does resolve to something. I read there is a way in sendmail.mc to manually set a hostname but I never got it working: vi /etc/mail/sendmail.mc define(`confDOMAIN........

  • MySQL Show Print List of Field Names only without other data or attributes


    SELECT column_name FROM information_schema.columns W........

  • EXT4-fs error (device md20): ext4_add_entry: bad entry in directory #2552670:


    Jun 12 10:30:53 kernel: [724514.291670] EXT4-fs error (device md20): ext4_add_entry: bad entry in directory #2552670: rec_len % 4 != 0 - offset=216, inode=2553603, rec_len=94, name_len=84 Jun 12 10:30:53 kernel: [724514.292400] EXT4-fs error (device md20): ext4_add_entry: bad entry in directory #2552670: rec_len % 4 != 0 - offset=216, inode=2553603, rec_len=94, name_len=84 This happened when an unprivileged user was backing up a Windows filesystem, once they ha........

  • WD 20EARX Dead Again


    Another new drive bad from the start: Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........

  • WD 20EARX 2TB Bad within days


    This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad. ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0 ata1.00: irq_stat 0x40000008 ata1.00: failed command: READ FPDMA QUEUED ata1.00: cmd 60/00:00:........

  • mysql how to execute script from the bash prompt .sql


    mysql -u username --password='yourpassword' ........

  • Country List Names in HTML Select From


    This is useful for developing a lot of applications, I'm putting it here to keep it handy for myself and hopefully others: Choose CountryCanadaJapanUnited StatesUnited KingdomAfghanistan........

  • Directadmin Log File Locations


    This is a handy link and list of all the relevant Directadmin log files and related servers. http://help.directadmin.com/item.php?id=11 DirectAdmin: /var/log/directadmin/error.log /var/log/directadmin/errortaskq.log /var/log/directadmin/system.log /var/log/directadmin/security.log Apache:........

  • Bad Hard Drive Slows Down Computer


    Here's a proven example of what a bad hard drive can do, it was technically functioning OKin a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application. The truth is that this failing 1TBHitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..). After swapping it out, tabs change instantly, emails are not lagged, and........

  • How to install GRUB to the MBR of a disk image.


    cat | grub --device-map=/dev/null Now pay close to the attention of the beginning. Type: "device (hd0) VPS.img" this is telling what hd0 will be to GRUB and we're telling it the disk image file "VPS.img" in the current directory is hd0, you can specify alternate paths and image names of course. GNU GRUB version 0.97 (640K lower / 3072K upper memory) [ Minimal BASH-li........

  • Setup PXE Boot using Centos and dhcpd, tftp and syslinux


    This is something I often setup for clients because it's very helpful for people in datacenters, this allows custom OS installs on demand, you can customize it more by using kickstart etc.. but here's a base I use before customizing more: This little script below will install everything you need to get booting by PXE Linux. It also assumes you set a local IP (be sure not to overwrite your existing IP) on eth0:0 (note the :0) as 192.168.1.10 and it........

  • Centos how to upgrade from PHP 5.2 to 5.3 without downtime


    This may sound silly but there will be conflicts/issues with the default Centos repository so you have to use a third party like remi (I prefer not to do this but it's the only option unless you migrate your sites/data to another server or can stand some downtime-not an option IMHOon a production server). You may need to upgrade to PHP5.3 to run Joomla or many other reasons. Your host needs to use PHP 5.2.4 or higher to run this version of Jo........

  • MySQL Authentication fails after Upgrade to Version 5.5


    ERROR 1045 (28000): Access denied for user 'contentmanager'@'localhost' (using password: YES) For fun I thought I'd reset the password: GRANT ALL ON thecontent.* TO contentmanager IDENTIFIED by 'dfdfsdfdsfsdfsd'; ERROR 1470 (HY000): String 'contentmanager' is too long for user name (should be no longer than 16) This is ridiculous that this new version has some bizarre 16 character username limit and not only that but i........

  • Windows Secret Hidden Temp Directory to free out of disk space issues


    Replace "Administrator" with your username. C:Documents and SettingsAdministratorLocal SettingsTemp Ihave often found several gigabytes of temporary files in there! Just be warned that they may not all be deletable if the files are being used by open programs (so close everything you can). This helped me in a pinch many times when for apparently no reason gigs of disk space are being used for an unknown reason.........

  • Directadmin Enable SSL


    It's really silly how DA doesn't enable SSL by default but is otherwise a stable, fast and secure control panel. Here's a copy and paste way of enabling SSL for Directadmin in just a few seconds: *setup SSL openssl req -x509 -newkey rsa:1024 -keyout /usr/local/directadmin/conf/cakey.pem -out /usr/local/directadmin/conf/cacert.pem -days 9999 -nodes That creates the public certificate and private key pair in the location Directadmin expects to fi........

  • Xen non-HVM container won't work/boot anymore


    One of my test Centos 5 containers was on a partition that filled up and it threw all sorts of errors and stopped responding but now I can't boot it again anymore. All the console shows is the Linux Penguin on the top left corner and the xm console says "usbcore: registered new driver hub" and has halted there. Centos 5 Xen container stuck/frozen won't boot on "usbcore: registered new driver hub" Another great way of troubleshooting is booting fro........

  • File /etc/vz/conf/ve-vps.basic.conf-sample not found: No such file or directory - Openvz Error solution


    Stuff like this always happens/breaks after a vzctl update, whether it's new parameters being added or required etc.. File /etc/vz/conf/ve-vps.basic.conf-sample not found: No such file or directory Fix the value of CONFIGFILE in /etc/vz/vz.conf Creation of container private area failed Warning: distribution not specified in CT config, using defaults from /etc/vz/dists/default WARNING: /etc/vz/conf/4400.conf not found: No such file or directory........

  • Ubuntu 10 Nvidia Drivers Not Updated After Kernel Update Solution/How-To Manually Rebuild nvidia kernel modules for Ubuntu


    I dread updating the kernel and rebooting to find the Ubuntu graphics aren't working and you have to manually intervene. This is usually because Ubuntu for whatever reason didn't update the drivers you need (eg. the manually compiled Nvidia Kernel driver that MUST be recompiled for each and every kernel update unfortunately). The most common reason may be that "linux-source" hasn't been installed automatically on my system. I tried to manually reinstall the........

  • Drupal/MySQL database error: PDOException: SQLSTATE[42000] [1044] Access denied for user 'db_user'@'localhost' to database 'dbname' in lock_may_be_available() (line 167 of /home/user/public_html/includes/lock.inc).


    PDOException: SQLSTATE[42000] [1044] Access denied for user 'db_user'@'localhost' to database 'dbname' in lock_may_be_available() (line 167 of /home/user/public_html/includes/lock.inc). The username and password were correct but some reason CPanel added the user with no permissions! Edit the user's permissions to include "All" from Cpanel or MySQL and that is the solution.........

  • How To Burn ISO Image using cdrtools/dvdrtools for Linux/Unix Ubuntu/Debian/RHEL/Centos etc..


    It really is as simple as: cdrecord -v dev=/dev/sr0 pathtoyourisoimage.iso -v is for verbose, I prefer it but if you don't you won't see as much output like below (I like to know the details and exactly what's happening) dev=/dev/sr0 specifies the device name of your burner (they say not to use it and to specify some weird annoying device string but using the raw /dev has always worked for me and is how it should have been implemented from the start IMHO)........

  • gocr - free Linux OCR (Optical Character Recognition) conversion tool


    gocr works great and it's simple, just invoke it like so: gocr filename.png The output will be printed to the screen. My only complaint/concern is that even with standard terminal output (not scanned) from a printscreen, gocr does make mistakes by inserting extra spaces where they don't belong, mistaking letters for numbers etc.. but it's definitely enough to be readable and figure out what you're looking at. I haven't tested yet with scanned input........

  • Linux Kernel Panic Messages - Symptoms of bad RAM module/stick


    These were caused by a bad stick of Corsair RAM [] free_hot_cold_page+0xfc/0x150 [] __pagevec_free+0x14/0x1a [] release_pages+0x127/0x12f [] __pagevec_release+0x15/0x1d [] __invalid_mapping_pages+0x120/0x156 [........

  • samba/smbd connection to share problems and solutions


    I'll start by showing some problems in the logs: [2011/08/07 16:22:06, 0] param/loadparm.c:8569(process_usershare_file) process_usershare_file: stat of /var/lib/samba/usershares/movie failed. Permission denied [2011/08/07 16:22:06, 1] smbd/service.c:676(make_connection_snum) create_connection_server_info failed: NT_STATUS_ACCESS_DENIED That means you don't have permission to access the fi........

  • Linux Out of Memory OOM Object Killer Solution "Out of memory: kill process 1955 (sshd) score 81 or a child"


    I had a system running a 128MB live CD image with 2.8 gigs of available RAM and the OOM kernel killer went crazy when using dd for more than 8 minutes and kept killing everything. I've read that this is due to a low-memory issue and paging in the kernel and 32-bit systems with lots of RAM. I even enabled swapspace on my LiveCD and the issue happened 25 minutes into dd rather than 8 minutes, so what gives? Also no swap space was ever used! cat /proc/s........

  • How To Test If Your Hard Drive Is Good/Signs of dying hard drive


    I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem: We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........

  • smart is not smart, it thinks a dead drive is still good


    I had a dying drive that smart thought until it totally disappeared was a good drive, and actually all parameters did look fine but this system was causing my system to lockup and other bad behavior: === START OF INFORMATION SECTION === Device Model: WDC WD20EARS-00MVWB0 Serial Number: WD-WMAZ20139 Firmware Version: 50.0AB50 User Capacity: 2,000,398,934,016 bytes Device........

  • GRUB Solution to error "Error 6: Mismatched or corrupt version of stage1/stage2"


    GNU GRUB version 0.97 (640K lower / 3072K upper memory) [ Minimal BASH-like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else TAB lists the possible completions of a device/filename.] grub> root (hd1,0) Filesystem type is ext2fs, partition type 0xfd grub> setup........

  • Hitachi 2TB HDS5C3020ALA632 drive DOA


    I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead): ata1: link is slow to respond, please be patient (ready=0) ata1: softreset failed (device not ready) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: link online but device misclassified, retrying ata1: link is slow to respond, please be patient (ready=0) ata1: softreset f........

  • How to recover from dead DRBD partition/hard drive in two simple commands


    This assumes that you've at least created the correct partition for your DRBD already. Notice that I am "diskless", that's because either your DRBD partition doesn't exist/has been renamed (eg. sdb becomes sda when sdb dies and you reboot) or because that drive is really actually dead/gone. *If you need to permanently change the partition/device for your resource be sure to edit /etc/drbd.conf on both hosts and reload the config. (replace r0 with........

  • Virtualbox How To Clone VM/Container VDI file


    You can't just do a straight copy of the VDI image of your virtual machine because there is a unique UUID, wellI believe you can and then you can create a new UUID manually (at least you could with VMWARE) but to keep it clean just use this method: VBoxManage clonevdi /path/to/your.vdi outputname.vdi 0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100% That's all there is to it, just wait for it copy and you can th........

  • Directadmin Solution "This is e-mail notification to warn you that your hostname is setup improperly on your system."


    This is e-mail notification to warn you that your hostname is setup improperly on your system. This is an annoying message and bug with Directadmin, my hostname is set correctly, why does it complain? To get of this message just run this command: /usr/local/directadmin/scripts/hostname.sh yourhostname.com........

  • Yahoo Mail (email) DNS Server Out Of Date Problems


    I don't expect this to be solved soon but some of Yahoo's DNS servers are out of whack. I changed the IPs of some nameservers of some domains and now most Yahoo users can't e-mail to those domains! As you can see below by the "No MX or A records for mychangedomain.com", now Yahoo's DNS/mailserver DNS cache is wrong. You would think they would at least have cached the old incorrect records, but instead for some reason their DNS cache has no entry and doesn't seem........

  • Linux High IOWAIT updatedb can't be killed and crash with mdadm


    high IO wait 424 root 39 19 1900 848 552 D 0.0 0.0 0:00.91 updatedb root 424 0.0 0.0 1900 848 ? DN Mar11 0:00 /usr/bin/updatedb -f sysfs?rootfs?bdev?proc?cpuset?binfmt_misc?debugfs?sockfs?usbfs?pipefs?anon_inodefs?futexfs?tmpfs?inotifyfs?eventp........

  • Enable SPAMASSASSIN on Postfix in 5 minutes


    Centos 5 Postfix and SPAMASSASSIN Tutorial yum install spamassassin chkconfig spamassassin on vi /etc/mail/spamassassin/local.cf ############## #required_hits 5 #report_safe 0 #rewrite_header Subject [SPAM] #5 is the least restrictive (means only the most obvious SPAM is caught. 0 is obviously the most restrictive/sensitive and would have lots of false positives require........

  • Plesk Get List of E-mail Users & Aliases


    When migrating away from Plesk I couldn't figure out an easy way to get a straight list of all e-mails, but here is where I found the solution: http://nakuls77.wordpress.com/2008/08/30/details-of-email-ftp-database-users-from-psa-database/ mysql> SELECT mail.mail_name, accounts.password, domains.name FROM mail, accounts, domains WHERE domains.id=mail.dom_id AND mail.account_id=accounts.id; mysql> SELECT CONCAT(mail.mail_name,’@’,domains.name) AS Em........

  • email server messsages rejected without reverse DNS DNS check failure Client host rejected: cannot find your reverse hostname Cannot resolve PTR record


    Basically you should always be 100% sure that whatever IPyour mail server sends out with has reverse DNS/PTR records. Remember that unless you own your IPs then you won't be able to set your own reverse DNS. Even if you were to create a reverse PTR record on your DNS servers it will be ignored. Reverse DNS is queried to pre-assigned DNS servers of your ISP, so therefore you'll need to contact your ISP/Colo/Hosting provider to do a reverse DNS entry. If you don't have........

  • named/bind cannot find zone file, load zone files without specifying full directory path/loading master file genuine.com.zone: file not found


    genuine.com/IN: loading master file genuine.com.zone: file not found _default/genuine.com/IN: file not found I always found it silly that no one really talks about this and apparently many like me and even control panels like Plesk were still using hard paths. I always thought "why can't I just specify the name of the zone file and have bind find it". Surely the default search path must be /var/named or somewhere else but there is no such thing.........

  • updatedb/mdadm caused a kernel panic?


    Jan 16 04:02:03 centosbox syslogd 1.4.1: restart. Jan 16 04:07:34 centosbox kernel: INFO: task updatedb:20771 blocked for more than 300 seconds. Jan 16 04:07:34 centosbox kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Jan 16 04:07:34 centosbox kernel: updatedb D F78BE050 6476 20771 20766&n........

  • rsync preserve attributes, permissions/ownership and times without being root non-root user


    One of the purposes of rsync is to backup whole filesystems and archive them but how can you do that properly and restore things to normal if all permissions and ownerships are not preserved from your root filesystem? It's not desirable to have everything running as root, especially not just for an rsync. The Easy rsync preserve permission solution for non-root users sudo is the answer and all you have to do is edit /etc/sudoers At the end o........

  • bash script count unique/dupllicate lines in a file


    For many reasons you may be dealing with a standard text file and you want to know if there are any duplicate lines: Here's how you do it: cat filename|uniq -c The "uniq -c" program counts how many time each line occurs.........

  • Outsourced VPS Support


    The Xen VPSI had was not working properly and when they asked for the login information I found the support was coming directly from India: whois 122.178.148.* [Querying whois.apnic.net] [whois.apnic.net] % [whois.apnic.net node-5] % Whois data copyright terms http://www.apnic.net/db/dbcopyright.html inetnum: 122.178.128.0 - 122.178.191.255 netname:&........

  • WD (Western Digital) Advanced Format Drive Lagged/Slow Speed/Performance/Design Flaw EAD/EARS problem WDC WD20EARS-00S8B1


    Let the numbers speak for themselves, from what I read the Load_Cycle_Count which is very high (more than 500,000/half a million times) is the number of head parks. What a stupid"Green" design and design flaw which will probably mean an early life for the drive. This is almost as silly as Seagate's new reputation for BSY/poor quality disks since the 7200.11 series. To make it worse this is also when Western Digital introduced "Advanced Format" o........

  • Nautilus/GNOME File Manager handy list of extensions


    nautilus-gksu - privilege granting extension for nautilus using gksu nautilus-sendto - integrates Evolution and Pidgin into the Nautilus file manager nautilus-share - Nautilus extension to share folder using Samba nautilus-actions - nautilus extension to configure programs to launch nautilus-bzr - Bazaar (bzr) integration for nautilus nautilus-cd-burner - CD Burning front-end for Nautilus nautilus-clamscan - Antivirus scanning for Nautilus n........

  • How not to change an IP address in CPanel during a migration


    /usr/local/cpanel/bin/swapip domain(s) It simply doesn't work, the Apache VHOSTS remain 100% unchanged, why does this script exist? I'm sure it would work from the control panel but I am locked out because my IP was changed and it doesn't match the CPanel license. I wish CPanel would make it easier to update the license IP. I even took it a step farther, I manually edited the vhosts and restarted Apache and it........

  • mencoder Linux CLI video editing how to encode video file into xvid and split by time into multiple parts


    Mencoder is great, you can throw anything at it, including video files from your camera and have it encode into xvid or almost any other format. In my case I took 640x480 video from my Canon and reduced the size by 1/3 with the options below (there are many other options that you can read about in the manual but I like to keep it simple). Mencoder Encode mencoder -ovc xvid -oac mp3lame -xvidencopts fixed_quant=4 -o ........

  • mdadm "auto-read-only" Linux Software RAID solution


    If you have the "(auto-read-only)" beside an arrayI have no idea why that happens but it is easy to fix. Just run "mdadm --readwrite /dev/md1" (rename md0 to the device with the problem and it will begin to resync. md1 : active (auto-read-only) raid1 sdb2[0] sda2[1] 19534976 blocks [2/2] [UU] resync=PENDING ........

  • Realtek r8169 1gbit/1000mbit NIC/Ethernet Goes Down/Halts on Large File Transfer/Heavy Network Usage


    This is obviously a bug in the r8169 kernel module and it seems to affect a lot of people. I upgraded to the latest kernel and hope this won't happen anymore, as it is a very serious error. This is especially serious for those who are running servers with this chipset, who can afford for the NIC to randomly go off-line for no apparent reason? [655548.189113] type=1505 audit(1277067560.902:5): operation="profile_load" name="/usr/bin/freshclam&q........

  • MySQL Insert Statement ONLY IF a duplicate entry does not exist


    This is a great way to reduce MySQL code/mistakes/annoyance when doing things, take for example this statement: INSERT IGNORE INTO sometable(CatName) VALUES("someitem"); Notice the "IGNORE", that is what does the magic. Normally if the entry "someitem" existed you'd get an error message back such as "Duplicate entry for whatever". What I have normally done in PHP or whatever language is manually coded or made a........

  • FUSE/Curlftpfs mount ftp account as drive partition in Linux


    This is a great way to use your ftp server space, for example on your web hosting account (althoughI believe many hosts don't allow storage like this), but if you have a VPS/Dedicated Server etc.., this would be perfect. Imagine how easy it is to work with an ftp account that you can just mount as a normal partition or directory in Linux, it would be great for backups etc.. Name curlftpfs - mount a ftp host as a local directory Synopsis........

  • Use rcconf to edit startup/init.d/init scripts on Debian/Ubuntu based distributions


    I've never understood how to enable and disable services for different run levels in Debian based distros, it's just weird, annoying and doesn't make sense. I much prefer chkconfig from RHEL. Just install the package called 'rcconf' and be done with it. rcconf makes things easy for you. apt-get install rcconf Reading package lists... Done Building dependency tree Reading state information... Done........

  • cPanel complaint - No Shared SSL! cPanel 11.25.0-R46156 - WHM 11.25.0 - X 3.9


    I've recently used CPanel on the admin side for the first time and have to say I hate it. Everything from the layout to the functionality screams "hackish". It just lacks so many common sense features and way of working. I was never 100% impressed with Plesk but the basics were definitely laid out and done in a sensible manner, even though it is made by a Russian company, they definitely thought about how to make a Control Panel. I have no idea why people........

  • CPanel Solution for Error Missing HOST Config Line in /etc/wwwacct.conf, please reconfigure with Edit Setup.


    Edit /etc/wwwacct.conf Then add/edit the HOST line to add your hostname. eg: HOST yourcpanelserver.com........

  • mdadm force/fix proper md127 name


    I have an md0 arary that my Centos install refers to. I feel this is half the reason why it won't boot anymore. I saw the initrd for Centos was assembling it as md127 even though it was known as md0. The reason for this is because I used mdadm --assemble --scan to detect the array on a LiveCD. I had no idea this name would stick (but now I realize the name is permanently stored in the metadata once you mount md127 or whatever random name assemble gives it). W........

  • MySQL Recover/Reset Lost/Forgotten root Password


    One note is to secure MySQL, I don't know for sure but I believe you could login to MySQL remotely with no password during this operation (I'm not sure, maybe it doesn't accept blank passwords but I firewall MySQL port anyway and recommend you do the same). First edit /etc/my.cf Under the [mysqld] field add the following line somewhere: skip-grant-tables Now restart mysql: service mysql restart or on Debian sty........

  • Centos 5.5 RAID 1 boot issue


    I installed 5.5 with a 300GB RAID 1 partition (boot is also on this partition). It booted up fine the first few times until after I used a Live CD and accessed the array, and it became named /dev/md127 for some reason. Now whenI boot into CentOS I get a kernel panic and different errors, once I got "invalid superblock", even though the array is fine (it didn't happen again, probably because I was sure to dismount and stop the mdadm array properly). Here's what........

  • SSH Automatic/Passwordless Logon - Setup Public Key Encryption In Single Command


    This is a very simple solution, but most guides out there make you login twice (once to scp the key) and once to put the key in authorized_keys. There's no need for that. If you don't already have a ~/.ssh/id_rsa.pub just type "ssh-keygen -t rsa" and keep hitting enter until it's done :) Just use this code to easily enable passwordless login with SSHD key=`cat ~/.ssh/id_rsa.pub`;ssh user@192.168.5.25 "echo $key >> ~/.ssh/auth........

  • Choose Which GCC Version to compile with via CC environment variable.


    It's very common to have multiple GCC versions for different reasons, as annoying as it is. Some newer/older programs only compile properly or at all on specific versions. You can export the following variable CC: export CC=gcc-4.1 Replace gcc-4.1 with the filename of the gcc you want eg. gcc-99........

  • mdadm Linux Software RAID auto-detect and assemble RAID Array


    mdadm --assemble --scan mdadm: /dev/md/diaghost05102010:2 has been started with 2 drives. mdadm: /dev/md/diaghost05102010:1 has been started with 2 drives. mdadm: /dev/md/diaghost05102010:0 has been started with 2 drives. -bash-3.1# cat /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid6] [raid5] [raid4] [multipath] md125 : active raid1 sda1[0] sdb1[1] 14658185 blocks super 1.2........

  • Seagate Drive 500GB Drive Dying


    This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device........

  • Seagate 7200.11 firmware defect in 500GB, 1000GB (1TB) and 1500GB (1.5TB) Hard Drives


    Seagate Inventory/Firmware Check I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate. *Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate! Seagate Inventory/Firm........

  • OpenVZ backup container to a single file while it's running using "vzdump"


    Proxmox has made this free utility to backup running OpenVZ containers. It's a great program which is actually just a PERL script but gets the job done. This program is not 100% required because all it really does is cp -a from your container's path as far as I know but it is still good to have uniformity to how you backup your containers. For RPM distros such as Centos/RHEL/Fedora etc.. download and install this: wget http://www.proxmox.com/cms_proxm........

  • Windows XP How To Edit/Find Recent Documents and "File -> New" Templates to create New Word Document, Text/Notepad, Excel etc...


    All you have to do is browse to: C:Documents & SettingsYourUserName and you'll see the following: Inside "My Recent Documents" are of course shortcuts to the most recent documents you opened Inside "SendTo" is your sendto, you could edit that to Send a file to a network destination, your Flash Drive........

  • PHP cannot access /usr/bin/openssl


    PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist: [code:1:1fd0f3abbe] if (!file_exists($OPENSSL)) { //echo "ERROR: OPENSSL $OPENSSL not foundn"; }[/code:1:1fd0f3abbe] I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........

  • rsync bash script


    rsync bash script [code:1:722d8a25c1]#!/bin/bash # config --------------------------------- # two methods # from = receive data from another server # to = send data to another server rsync_method=from rsync_ip='192.168.5.18' local_dir='/home/backupguy/backups' remote_dir='/home/backup' free_space_bin='/home/backups/freediskspace.sh' # config end ------------------------------ if [ '$rsync_me........

  • Javascript Get a specified element using getElementById()


    Javascript Get a specified element using getElementById()Great, it produces the value for whatever "id" is passed to the function. http://www.java2s.com/Code/JavaScript/Development/GetaspecifiedelementusinggetElementById.htm [code:1:1287ede953] function getElement(){ var x=document.getElementById("myHead........

  • Need identd for port 113 ? Install authd


    Need identd for port 113 ? Install authdyum install authd Happy identing :)Actually it's not that simple. It installs as an "xinetd" service and is disabled and turned off by deafult. To enable it run: [code:1:8c94df8319] chkconfig --level 3 auth on service xinetd restart [/code:1:8c94df8319] This will set identd aka authd to start by default. service xinetd resta........

  • E-Mail Tip


    E-Mail TipI just thought I'd give you guys a good tip about e-mail. It seems a lot of people like to use a Hotmail or ISP (eg. Telus) account for their e-mail but the problem is what happens if you switch ISPs, then your e-mail address no longer works and old friends might not be able to contact you. The same thing has happened for excite.com e-mail addresses where they just shut down. Whether you are a business owner or personal user can you afford to lose an e-mail........

  • MySQL Server 3.23 won't start after switching from 4.1


    MySQL Server 3.23 won't start after switching from 4.1I was using a 4.1 alpha version of mysql-server and some how version 3.23 of the client and 4.1 of the client were also both installed! So I forced uninstalled everything because after trying and trying even though MySQL server was using the short 16byte password authentication I got some other errors. After trying with the ports and having it fail because I had existing database data I force installe........

  • Changing field names


    Changing field names[quote:91ea6831b6]ALTER TABLE [u:91ea6831b6]table_name[/u:91ea6831b6] CHANGE [i:91ea6831b6]existing_field_name[/i:91ea6831b6] [b:91ea6831b6]new_field_name[/b:91ea6831b6] INT(11);[/quote:91ea6831b6]........

  • PHPBB Drop All Tables


    PHPBB Drop All TablesSQL Syntax: [quote:75acd496c1]drop table phpbb_auth_access, phpbb_banlist, phpbb_categories, phpbb_config, phpbb_confirm, phpbb_disallow, phpbb_forum_prune, phpbb_forums, phpbb_groups, phpbb_posts, phpbb_posts_text, phpbb_privmsgs, phpbb_privmsgs_text, phpbb_ranks, phpbb_search_results, phpbb_search_wordlist, phpbb_search_wordmatch, phpbb_sessions, phpbb_smilies, phpbb_themes, phpbb_themes_name, phpbb_topics, phpbb_topics_watch, phpbb_user_group, p........

  • REMOVE a field


    REMOVE a field[quote:effdb203d8]ALTER TABLE table_name DROP field_name[/quote:effdb203d8]........

  • Tar & Encrypt in the same command!


    Tar & Encrypt in the same command![code:1:f2c600dbb6]tar -cz --file=tarfile.tar `gpg -e -r email@address file.name`[/code:1:f2c600dbb6] Notice the back ticks in the place where the filename would normally be. This will let us encrypt and tar any files/directories!........

  • Create Table with structure of another existing table


    Create Table with structure of another existing tableOk, this has many valid uses such as if you need to create backups or the ability to undo changes, you would want to create new tables with the same structure as another. Here is how you do it. [i:7ed9581493] Also remember Indexes such as PRIMARY KEYS [b:7ed9581493]will not be preserved[/b:7ed9581493] so you will have to readd them manually.[/i:7ed9581493] [code:1:7ed9581493]CREATE TABLE NewName AS SEL........

  • ADD PRIMARY KEY to Table


    ADD PRIMARY KEY to TableHere is an example of readding a PRIMARY KEY with an AUTO_INCREMENT field: [b:40986c2a8b]First make the field NOT NULL[/b:40986c2a8b] [code:1:40986c2a8b] ALTER TABLE tableName MODIFY FieldNAME INT(18) NOT NULL; [/code:1:40986c2a8b] [b:40986c2a8b]Create The Primary Key[/b:40986c2a8b] [code:1:40986c2a8b]ALTER TABLE tableName ADD CONSTRAINT PRIMARY KEY(FieldName);[/code:1:40986c2a8b........

  • Create/Enable SSL Certificates for Apache on Linux/Unix Systems eg. Redhat,Centos,Debian


    Shortcut/Easiest Way To Create A Self-Signed Key: openssl req -new -x509 -nodes -days 1530 -out server.crt -keyout server.key Using the above, you instantly create a self-signed certificate valid for 1530 days and you can simply skip to step #5.) below. If You Need a Real SSLCertificate (eg. Equifax/Openssl) then you need to create a CSR request (you'll need to follow Steps 1.) and 2.) in order to create the CSR. You then upload the CSR Certi........

  • Adventures in pre-paid SIM Cards and data GPRS/Edge/3G in China with China Mobile in Shenzhen, Guangzhou, Shanghai, Beijing and other cities


    This really is a difficult and confusing process for non-Mandarin speakers, but here's what I've done and learned so far: You can purchase an "M-Zone" China Mobile pre-paid SIMCard from almost anywhere but I tried to purchase mine from Suning (a large electronics dealer) hoping they would be able to help me or answer my questions but my plan didn't work out at all. At Suning once I found someone who spoke some English they gave me the 55 RMB M-Zone China Mobile P........

  • How to avoid web content hijacking/copying/Force content to be accessed by only 1 domain name


    This is something that happens a lot and it is very dirty, as you probably know each site is hosted on a certain IP address. Sometimes a domain is hosted by a single IP address and the IP address defaults to this very same domain. This means that if someone buys domain abcd.com and enters your IP address (the one of your website) as the A record, your content will show up on their domain as if it was their own. There is an easy way to prevent this by using .htacces........

  • GRUB "Error 2: Bad file or directory type" 0.97 won


    You can see the problem below, GRUB recognizes my hard drive and sees the partitions but cannot access them. This is from the GRUB boot disc I'm using. What happened is that I had some power issues causing this system's power to be interrupted several times and basically an on/off on/off situation. The system won't boot, I just get a flashing cursor and no message or error from GRUB. Obviously the problem is that my MBR seems corrupt or some other issue. My........

  • Linux Bash Shell Cannot/Can't View File That Starts With - Dash ?


    Iwas getting really annoyed with this, I used full quotes around the filename and vi, cat, less all thought I was trying to pass the dash in the filename as an argument. I didn't realize that all you have to do is just put a dash dash "--"in front. Here's an example:cat -- "-etc-glusterfs-glusterfsd.vol.log" Without the -- you get: cat: invalid option -- c Try `cat --help' for more information. Ih........

  • MySQL Restoring And Dumping/Backing UP MySQL Data/Tables/Databases


    Backing MySQL Databases Backing Up/Dumping All Mysql Databases To A Single File mysqldump --all-databases -u admin -p > allmysqldatabases.sql The "-all-databases" clause is pretty obvious isn't it? It means that it will backup all databases. The "-u admin" means login using the user "admin", if you h........

  • Samba SMB Error - Server not using user level security and no password supplied. tree connect failed: NT_STATUS_WRONG_PASSWORD


    Server not using user level security and no password supplied. tree connect failed: NT_STATUS_WRONG_PASSWORD That happens when trying to use smbclient to connect to a share. The weird thing is that I can authnenticate just fine from Windows XP. It is partially my mistake, I forgot this share does have a password. I've tried authenticating with the correct user and also with "Guest" because this works in Windows. In Linux I ........

  • Configuring OCFS2 Clustered File System on Debian Based Linux including Ubuntu and Kubuntu


    There's a lot of information and guides on OCFS2 for RHELand Centos Linux but the package setup and configuration is slightly different and this has thrown some people off. Installing OC2FS You should install the following packages to get started: apt-get install ocfs2-tools ocfs2console Configure OC2FS In RHEL/Centos the main configuration file is located in /etc/sysconfig/o2cb However in Debian based Linux it is located........

  • Viewing and Connecting to an SMB Samba Share on Windows/Linux/Unix


    This will give you the basic info needed to browse and connect to Samba shares from the command line. From the GUI of Gnome or KDE etc, it is pretty standard and straight forward. However, I've found very little guides on how to do it from the command line and if you're like me, a nerd who prefers command line for its simplicity and for remote use, this is the way to go. First get a list of all the Samba/SMB shares on the target. smbclient -L hostname........

  • SSH Problem User username from 127.0.0.1 not allowed because not listed in AllowUsers


    User username from 127.0.0.1 not allowed because not listed in AllowUsers What's going on? The user was created properly, it has been defined as having a shell entry and the entry for /etc/passwd and /etc/shadow is set just fine. This is a new and very smart/secure feature of SSHD. It is simple and yet effective, but also very annoying if you didn't know about it being implemented and that hand editing of /etc/ssh/sshd_config is required to allow a newly add........

  • ENOM Major Outage


    At this time we can't resolve Enom's website and all DNS requests to their 4 primary name servers are failing, although the hostnames themselves still resolve: Name Server: DNS1.NAME-SERVICES.COM Name Server: DNS2.NAME-SERVICES.COM Name Server: DNS3.NAME-SERVICES.COM Name Server: DNS4.NAME-SERVICES.COM Name Server: DNS5.NAME-SERVICES.COM You would really think Enom, bein........

  • Writing/Burning a data CD-R/DVD-R or DVD+RW in Unix/Linux


    There's a lot of outdated information and confusion for system administrator's out there. One annoying task for many an Administrator has been backing up data in Linux. You don't need any GUI tools such as K3B or GnomeBaker. Both are excellent tools but for veteran command line users working remotely, using the keyboard is a great and possibly automated way to save yourself pain and hassle. At a later date we'll cover how scripting can automatically backup certain........

    • Latest Articles

  • How high can a Xeon CPU get?
  • bash fix PATH environment variable "command not found" solution
  • Ubuntu Linux Mint Debian Redhat Youtube Cannot Play HD or 4K videos, dropped frames or high CPU usage with Nvidia or AMD Driver
  • hostapd example configuration for high speed AC on 5GHz using WPA2
  • hostapd how to enable and use WPS to connect wireless devices like printers
  • Dell Server Workstation iDRAC Dead after Firmware Update Solution R720, R320, R730
  • Cloned VM/Server/Computer in Linux won't boot and goes to initramfs busybox Solution
  • How To Add Windows 7 8 10 11 to GRUB Boot List Dual Booting
  • How to configure OpenDKIM on Linux with Postfix and setup bind zonefile
  • Debian Ubuntu 10/11/12 Linux how to get tftpd-hpa server setup tutorial
  • efibootmgr: option requires an argument -- 'd' efibootmgr version 15 grub-install.real: error: efibootmgr failed to register the boot entry: Operation not permitted.
  • Apache Error Won't start SSL Cert Issue Solution Unable to configure verify locations for client authentication SSL Library Error: 151441510 error:0906D066:PEM routines:PEM_read_bio:bad end line SSL Library Error: 185090057 error:0B084009:x509 certif
  • Linux Debian Mint Ubuntu Bridge br0 gets random IP
  • redis requirements
  • How to kill a docker swarm
  • docker swarm silly issues
  • isc-dhcp-server dhcpd how to get longer lease
  • nvidia cannot resume from sleep Comm: nvidia-sleep.sh Tainted: Linux Ubuntu Mint Debian
  • zfs and LUKS how to recover in Linux
  • [error] (28)No space left on device: Cannot create SSLMutex Apache Solution Linux CentOS Ubuntu Debian Mint
    • Copyright © realtechtalk.com 2024