• docker swarm silly issues


    The error below can be caused by a gateway that is unpingable: docker swarm join --token SWMTKN-1-1kogg8da68gtb1j7ezaddowyy9s0an5s9tue758o20k18liskw-5h3f61hrrmv3u6agshvbtcklf 172.16.1.80:2377 Error response from daemon: manager stopped: can't initialize raft node: rpc error: code = Unknown desc = could not connect to prospective new cluster member using its advertised address: rpc error: code = DeadlineExceeded desc = context deadline exceeded........
  • isc-dhcp-server dhcpd how to get longer lease


    You can do a static lease that is tied to the MAC address but what a lot of users prefer is that they come into the office or lab the next day and that their device gets assigned the same IP address (if possible). As we can see in the dhcpd logs that there is threshold that is defaulted as we'll show later. Whatever the threshold is set at, if the lease is younger than the threshold, it will keep the same lease. In other words, if the device goes to sleep or is powered off........
  • Linux how to get list of all timezones on system Ubuntu


    find /usr/share/zoneinfo/|sed s#"/usr/share/zoneinfo/"##g|grep "/"|grep -v posix|grep -v ^"Etc/"|grep -v ^right|grep -v ^"SystemV" Africa/Addis_Ababa Africa/Abidjan Africa/Blantyre Africa/Lusaka Africa/Casablanca Africa/Libreville Africa/Asmara Africa/Bujumbura Africa/Dakar Africa/Lagos Africa/Malabo Africa/Harare Africa/Kigali........
  • ecryptfs how to manually encrypt your existing home directory or other directory


    Just in case, it is reocmmended to backup the original contents of the directory (especially your home dir) before proceeding. Setup ecryptfs Run this command: ecryptfs-setup-private It will ask you for your login password, this is so that when you login, everything is automatically decrypted by using a passphrase that is wrapped with your login. You can hit enter and leave things blank for an autogenerated passphrase (for mounting) or you can en........
  • request_module: runaway loop modprobe binfmt-464c Kernel panic - not syncing: No init found Pid: 1, comm: swapper/0 Not tainted solution


    request_module: runaway loop modprobe binfmt-464c Kernel panic - not syncing: No init found Pid: 1, comm: swapper/0 Not tainted This is usually caused by a mismatch in architecture and happens frequently in development environments. Here is a example of what caused this issue: Your binaries are based on one architecture Your kernel was compiled with another architecture. Why does this happe........
  • How to install and configure haproxy on Linux Ubuntu Debian


    haproxy is one of the best known and widely used Open Source load balancers out there and a strong competitor to nginx. haproxy is used by many large sites per Wikipedia: HAProxy is used by a number of high-profile websites including GoDaddy, GitHub,........
  • talib/_ta_lib.c:747:10: fatal error: ta-lib/ta_defs.h: No such file or directory


    If you are installing ta-lib for Python and get this error then you can normally solve it by manually getting the ta-lib source files and compiling. tar -zxvf ta-lib-0.4.0-src.tar.gz cd ta-lib;./configure;make;make install Collecting ta-lib Downloading https://files.pythonhosted.org/packages/39/6f/6acaee2eac6afb2cc6a2adcb294080577f9983fbd2726395b9047c4e13ec/TA-Lib-0.4.26.tar.gz (272kB) &nbs........
  • RHEL 8 CentOS 8, Alma Linux 8, Rocky Linux 8 System Not Booting with RAID or on other servers/computers Solution for dracut and initramfs missing kernel modules


    This seems to have changed for RHEL 8 where a normal dracut to update your initramfs creates a system that only boots for the running kernel. For example if you have Kernel 5 and then chroot into a RHEL 8 variant which uses kernel 4.18, and run dracut, it seems that by default the system will be unbootable. It is also the case that if you move your RAID array or drives to another server that it will be unbootable, because dracut seems to only include modules needed for the curre........
  • Debian Ubuntu apt install stop daemon questions/accept the default action without prompting


    This can be a real pain when automating things and you do an apt install and some packages ask a lot of questions. Make sure you set this variable when running: DEBIAN_FRONTEND=noninteractive Remember as well that if chrooting you will want to run like this: DEBIAN_FRONTEND=noninteractive apt install -y yourpackagename ........
  • Stop ls in Linux Debian Mint CentOS Ubuntu from applying quotes around filenames and directory names


    Later versions of ls try to be helpful and smart to prevent errors in dealing with files with spaces that were tradtionally a pain. However if you need the raw/real filenames, this can break scripts or if you are pasting into a csv etc.... How do you make ls not add the quotes? Add the capital "-N" switch ls -N You could also add an alias to make it more permanent Do this to add it to ~/........
  • Ubuntu Debian Mint Linux How To Update Initramfs Manually update-initramfs


    The easiest way for the current running kernel is: update-initramfs -u -k `uname -r` You could change -k to a specific kernel name if for some reason the current is not running (eg. if you are chrooted or in recovery mode). If you want to update all kernels then use "-k all" update-initramfs -k all -u update-initramfs: Generating /boot/initrd.img-5.4.0-162-generic........
  • Enable Turbo Mode for CPU Ubuntu Linux Mint Debian Redhat


    Sometimes due to your BIOS/EFI you may find that you have chosen "Energy Efficient" for your CPU which may effectively disable turbo mode. This is because "Energy Efficient" will often restrict or throttle your CPU to the base speed. This can impact nearly any CPU such as Intel's, AMDs, Opteron, Xeon etc... This is of course frustrating, for example if you have a CPU that is 2.0GHz base speed but turbo to 2.5GHz, you will never hit more than 2GHz.........
  • How To Install convert MBR Legacy booting GRUB to EFI from a non-EFI Linux Environment Ubuntu Mint Debian


    1.) Create your EFI/ESP Partition If you happen to have some free space on the drive already then this is easy, just create a new partition of at least 100M. The nice thing about the EFI spec is that it must just be in the first 2.2TB of space so for most users, it means you can simply resize the last partition(downsize it by 100M) and then add an EFI partition at the end. For example if you had this partition scheme: /dev/sda1 = /........
  • GRUB error: invalid arch-independent ELF magic. Solution How To Fix Linux Centos Ubuntu Mint


    I've seen this bizarrely happen on a newly partitioned and custom installed Linux install, particularly if you did not properly unmount before rebooting. You can find reports of it happening on various How to fix the error: invalid arch-independent ELF magic. You need to boot into Live/Rescue mode, chroot into your OS properly and then do a grub-install on each drive that nee........
  • CentOS 7 / 8 cannot boot with with mdadm RAID array solution


    This article about migrating to a CentOS 7 /8 RAID mdadm array has a lot of info but I wanted to focus specifically on what newer versions of CentOS 7 require to boot mdadm and what changes are necessary on CentOS 7.8+ CentOS 7 / 8 mdadm RAID booting requirements This assumes you are chrooting into an existing install or using it to get a new deployment ready. However, these steps can........
  • ecryptfs How To Backup / Migrate Linux Mint Ubuntu Debian system ecryptfs properly and restore access


    In this scenario, let's say you want to clone your OS at the filesystem level and the source system (the system you want to clone from) is in use. Doing a blind rsync / is a big problem because it uses twice as much space for no reason. The reason for this is that with ecryptfs you have a /home/.ecryptfs directory which has the actual encrypted versions of your files and folders. However your home directory (eg. /home/someuser) is mounted. Doing the blind rsync will ca........
  • amdgpu AMD GPU Xorg Won't Start [3576284.324] (EE) Segmentation fault at address 0x0 [3576284.325] (EE) Fatal server error: [3576284.325] (EE) Caught signal 11 (Segmentation fault). Server aborting


    Here is how Ifixed it on a Mint/Ubuntu install 1.) First download the latest AMDGPU-Pro driver from here: https://www.amd.com/en/support Navigate to your relevant video card: 2.) Download the installer One issue is that by default they give you a version for the latest version of........
  • symbol 'grub_calloc' not found grub boot error solution / fix


    I've encountered this after upgrading some Debian/Ubuntu/Mint based systems for no explicable reason, although there are some bug trackers on Ubuntu that document this: https://bugs.launchpad.net/ubuntu/+source/grub2/+bug/1889509 The short end of the solution is that you need to properly reinstall grub. 1.) Boot from a LiveCD 2.) Mount your root / filesystem and don't forget to mo........
  • How To Do Linux Network Bonding Teaming in Mint Debian Ubuntu


    Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........
  • How To Shrink Dynamically Allocated VM QEMU KVM VMware Disk Image File


    Let's say you have a VM file that uses 200G of dynamic space, but really only has 40G in usage. If you add fles and delete, at some point the file will be larger than the current space you are using. Take this image which shows is using 71G of space on the host: The actual space being used inside the image is about 43G as we can see:........
  • (firefox:9562): LIBDBUSMENU-GLIB-WARNING **: Unable to get session bus: Failed to execute child process "dbus-launch" (No such file or directory) Solution


    (firefox:9562): LIBDBUSMENU-GLIB-WARNING **: Unable to get session bus: Failed to execute child process "dbus-launch" (No such file or directory) ExceptionHandler::GenerateDump cloned child 9743 ExceptionHandler::WaitForContinueSignal waiting for continue signal... ExceptionHandler::SendContinueSignalToChild sent continue signal to child [Parent 9562, Gecko_IOThread] WARNING: pipe error (40): Connection reset by peer: file /build/firefox-EymEXX/fire........
  • Docker Tutorial HowTo Install Docker, Use and Create Docker Container Images Clustering Swarm Mode Monitoring Service Hosting Provider


    The Best Docker Tutorial for Beginners We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........
  • How To Create OpenVPN Server for Secure Remote Corporate Access in Linux Debian/Mint/Ubuntu with client public key authentication


    Why choose OpenVPN instead of a firewall appliance? OpenVPN can be a reliable and easy replacement for traditional hardware or just be an additional tool that your company uses so that the firewall can focus on its job rather than acting as a VPNappliance at the same time. When comparing OpenVPN with traditional firewal........
  • HongKong VPS Server, Cloud, Dedicated Server, Co-Location, Datacenter The Best Guide on Hong Kong, China Internet IT/Computing


    In our 2024 VPS Server/Cloud Buyer's Guide, we place the location of your VPS/hosting/server as one of the priorities that is often overlooked. 2024 Update - Datacent........
  • ssh-keygen id_rsa private key howto remove the passphrase so no password is required and no encryption is used


    The key is that you need to know the passphrase to do it, if you don't know the password for the key then you can't remove the key since it cannot be decrypted. ssh-keygen is the easiest method and openssl can be used to manually remove the key and output it to a new file, which you can then copy back over top of the encrypted file. After that your public key authentication will work without any password prompt because it is no longer encrypted. Make sure you understand........
  • tag#4 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE tag#4 Sense Key : Illegal Request [current] res 40/00:b4:98:02:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) solution


    You might assume you have a bad drive or the SATA interface/cable is bad, or the power supply is bad/weak to the drive. These are all possible issues, but definitely check your SATA cable for "twisting". It is a big issue because until the error stops or times out, your system will not boot (in my case this was the case even though the drive with the issue was not part of the OS or booting process at all). If you run an open rig that you move around often that ha........
  • QEMU/KVM How to Hot-add A Virtual Disk .raw/.qcow2 via QEMU Monitor Commands


    For a lot of reasons, it may be convenient to detach or attach live disks to a running VM without having to reboot it. Sure, you can use some network based storage, but when performance counts, attaching a new virtual disk will usually give you better throughput and lower latency in a quick testing situation. This doesn't work, why not? drive_add 0 if=virtio,file=/tmp/vm.qcow2,if=virtio,format=qcow2,id=rtt Can't hot-ad........
  • pulseaudio issue on QEMU/KVM guest VM when microphone is replugged/unplugged pulseaudio: pa_threaded_mainloop_lock failed pulseaudio: Reason: Invalid argument


    Here is the scenario, you are using QEMU/KVM and are using something like the AC97 sound driver to pass the host audio to the guest via pulseaudio. This is useful because you can transparently pass your mic input from the host which means you can mute your microphone from the host, which prevents the guest from receiving any mic input even if unmuted. Mute / Unmute Fix This issue also seems to happen even if you press the mute button on the microphone and then unmute,........
  • Cisco Howto Configure Console Port/Terminal/Comm Server with Async Cable Setup


    This assumes that you've already installed the relevant HWIC cards eg. Cisco Asynchronous Serial NIM These are essentially cards that you install into your router, once installed you connect an Async cable to one of the ports on the card which normally gives you 8 console cables and are normally labelled 1 through 8. You connect all of the cables to the devices you need (even non-Cisco devices) whether switches, routers or firewalls, they will usually work. The real m........
  • bash how to hide username/customize prompt Linux Debian Redhat Ubuntu Solution


    Just edit your ~/.bashrc and add this at the very end: export PS1="realtechtalk.com" Then your prompt will look like this: bladeblox:uptime 08:47:14 up 48 min, 1 user, load average: 1.00, 1.07, 0.96 If you wanted a dollar sign at the end then you would change it like this: export PS1=&........
  • Linux can't boot/grub boot loader screen with no options solution


    Usually if you get the grub boot loader and it doesn't show any boot options, it's because grub was not installed correctly and/or the partition that it is supposed to be on has changed or does not exist. It can also happen if you install Linux to one drive, but the boot loader to another by accident, whether EFI or MBR/Legacy mode. You can normally fix your booting/bootloader/MBR/EFI it by chrooting into your root partition: #become root sudo su........
  • Juniper JunOS Command Overview and Howtos Switch, Router, Firewall Tutorial Guide


    Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........
  • Linux how to compile binary with static sharedobjects embedded instead of dynamic to use on multi-distributions and avoid glibc compatiblity issues


    One simple flag to configure will create a makefile that statically links all the shared objects and embeds them instead the binary execute. This means as long as you have the same architecture that things should run. Eg. if you have an old version of Debian with a different version of glibc, then this will solve that problem. ./configure LDFLAGS="-static" To test that it is really statically linked run ldd: ldd src/wget........
  • Mikrotik RouterOS CHR/ISO Basic and Quick Setup Howto Guide


    Many people may not be aware that you can turn commodity hardware into a Mikrotik OS and there are various options which is "CHR" (Cloud Hosted Router) which is a VMimage meant for Virtualization only (seriously, I've tried to dd the image to a physical server and it just crashed as it does not contain any drivers for physical). One note as well if you are trying to do a baremetal install you may get an error "Error Loading Operating System" or........
  • How To Replace Audio Track of Video using ffmpeg


    A very common use case is that you don't want to waste time using a video editor that requires you to open it up and manually import the video clip and audio clip, then manually delete the old audio track and import the video and new audio. That's too much work and time since we don't want to go through the hassle. ffmpeg is our solution, all we have to do is specify 3 variables and we're done! -i Windows2019-Server-Noaudio.mp4 is our in........
  • apcupsd how to setup and monitor APC UPS units


    It really seems limited in that it can mainly give you the things you would see on the physical unit such as load etc.. wget https://downloads.sourceforge.net/project/apcupsd/apcupsd%20-%20Stable/3.14.14/apcupsd-3.14.14.tar.gz?r=https%3A%2F%2Fsourceforge.net%2Fprojects%2Fapcupsd%2Ffiles%2Flatest%2Fdownload&ts=1598115866 tar -zxvf apcupsd-3.14.14.tar.gz cd apcupsd-3.14.14 [root@somebox apcupsd-3.14.14]# ./conf........
  • chroot


    chroot /root/kvmguests/4591915/mount FATAL: kernel too old This happens for example if you are in Centos 6 and trying to chroot into a system based on a newer kernel like 4.x+ You'll have to use a newer OS/kernel system to chroot into the environment or a VM running a newer kernel.........
  • How To Get Started on Ubuntu with gpt-2 OpenAI Text Prediction


    apt install software-properties-common add-apt-repository ppa:deadsnakes/ppa apt update apt install python3-pip apt install python3.7 curl gnupg python3.7-dev git ln -s /usr/bin/python3.7 /usr/bin/python3 pip3 install numpy keras_preprocessing curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add - echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........
  • Linux Debian Ubuntu How To Install PEPPER Faster and Latest Adobe Flash Player in Firefox


    Just run this apt install command sudo apt install pepperflashplugin-nonfree browser-plugin-freshplayer-pepperflash After this restart your browser and check Adobe's site to verify if your Pepper flash is working and showing at least version 32. https://helpx.adobe.com/flash-player.html As you'll see below it will download the latest version which is currently 32 and this was not possible with the old/crappy deprecated adobe-flash plu........
  • How To Speed Up Linux Ubuntu and Debian Based Computers By Improving CPU Performance and Changing the CPU Governor


    I used to believe that for Desktops especially that the "ondemand" CPUfrequency changing that kernels included with Ubuntu and Debian based distros have would be sufficient for snappy performance. However, you can feel the lack of performance on the fastest computer if you have ondemand. A lot of times even under high load 100% of your CPUfrequency in MHz will not be used. For example a 2.8Ghz CPUmay only run at 1.8MHz or even .9GHz. Now........
  • How To Install python 3.4 3.5 and up on Linux with wine - Working Solution


    This is sure simple if you follow the guide but it took a lot of hacking around to make this work on Debian/Ubuntu! Now before you ask why bother running wine and python, the reason is because Python executables are NOT cross-platform. If you run pyinstaller in Linux, that binary will only run on Linux and the same if you do it in Windows. So it is preferable if you have a single environment that you can create Linux and Windows binaries from rather than running 2 separate........
  • Radeon R3 GPU on Debian Crashing


    Occasionally my whole screen locks up and I cannot even swith to the console and I find this in my syslog: *-display description: VGA compatible controller product: Mullins [Radeon R3 Graphics] vendor: Advanced Micro Devices, Inc. [AMD/ATI]  ........
  • Convert and install to LUKS Encrypted Drive Ubuntu 18.04 19.10 Linux Mint and Debian Based Linux


    The reason for doing this is that the installer doesn't seem to work properly for LUKS and the server installer doesn't even support LUKS anymore. When you use the GUI install on Desktop for LUKS it won't boot and will just hang after you enter your password. So the only reliable way is to do it ourselves. 1.) Make a default minimal install of Ubuntu 2.) Have a secondary disk on the server or VM. 3.)........
  • CentOS 8 how to convert to a bootable mdadm RAID software array


    The cool thing here is that we only need 1 drive to make a RAID 10 or RAID 1 array, we just tell the Linux mdadm utility that the other drive is "missing" and we can then add our original drive to the array after booting into our new RAID array. Step#1 Install tools we need yum -y install mdadm rsync Step #2 Create your partitions on the drive that will be our RAID array Here I assume it is /dev........
  • mpv / mplayer with Radeon / AMD GPU Video Card Driver enable VDPAU GPU Accelerated Video Decoding


    The easiest way to know if your videos are playing with GPU acceleration are to watch the process of xplayer, mpv or whatever you are playing. The CPU usage should be no more than 10% for that process/program if it is using acceleration. Let's manually play with vdpau to make sure it works before we make it permanent: First make sure you have libvdpau installed: sudo apt install vdpau-driver-all If yo........
  • Ubuntu Linux Mint Debian xorg performance and tear-free tuning for AMD Radeon Based Cards


    I find that the default settings for the radeon driver that is applied to most AMD cards is horrible. For example by default TearFree is not enabled and it causes videos to have some kind of square artifacts. Here are the settings I have found most suitable for AMD cards: You need to create file in the following path and restart Xorg or your computer to apply it: *Beware that making a mistake here will possibly make your computer........
  • Linux 3D Performance benchmarks with glxgears 59-60fps solution


    You need to disable vsync like this when running glxgears: vblank_mode=0 glxgears For Nvidia drivers do this: __GL_SYNC_TO_VBLANK=0 glxgears Notice the higher than 59-60 fps results with vblank_mode=0: ATTENTION: default value of option vblank_mode overridden by environment. 7919 frames in 5.0 seconds = 1583.704 FPS 8187 frames in 5.0 seconds = 1637.266 FPS........
  • How to encrypt your SSH private key file id_rsa


    ssh-keygen -p -f /path/to/your/id_rsa Enter new passphrase (empty for no passphrase): After that your rsa private key will be encrypted which is a layer of protection and security in the event that somehow someone acquires your key and tries to access servers that the key is authorized on.........
  • Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM


    The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........
  • chroot in Linux Howto Simple and Easy Guide


    chroot which stands for change root allows you to virtually operate in another operating system even though you haven't booted it. It is commonly used to deploy new distros, applications and to fix a broken Linux/Unix install or prep a new system image without having to physically boot the drive or disk. So in this example let's say we have a drive that has a Linux OS installed on /dev/sdb1 and we have mounted this partition on /mnt/sdb1 The key point is to edit the &quo........
  • Linux bash prompt why does it not show username@host and the current directory?


    Perhaps you've just seen this in the bash prompt: -bash-4.1# Instead of the expected user@hostname# It is probably because you are missing .bash_profile or .bashrc in your home directory Check for yourself: ls -al ~/|grep -E ".bash_profile|.bashrc" -rw-r--r--. 1 root root&nbs........
  • Ubuntu 18.04 / Linux Mint 19.1 Cannot Type or Login - solution


    It was broken because of this package for xorg I installed: xserver-xorg-core-hwe-18.04 Just remove it even if you have to chroot from a live USB/CD: sudo apt-get remove xserver-xorg-core-hwe-18.04........
  • LUKS Hard Drive Encryption on Linux Mint Ubuntu Debian etc how to mount encrypted hard drive


    The key thing here is to know the actual partition that is encrypted. Often in Linux Mint's installer that ends up being partition 5 or /dev/sda5 sudo cryptsetup luksOpen /dev/sda5 anynamehere You will then be prompted for your irrecoverable passphrase: Enter passphrase for /dev/sda5: If all goes well it won't say anything further. If it says ""No key available with this passphr........
  • PHP Issues With Decoding Strange Smart Quotes And Non-Standard ASCII Characters


    When using strip_tags and html_entity_decode with PHPit often breaks and produces annoying diamonds with question marks. It is probably because of characters like these: … (looks like 3 dots but it is a single weird character). ’ (looks like a normal apostraphe but it is not) ” (looks like a normal double quote but it is not). An easy way to sort this out is to copy the above and search in an ASCII table to extend the functional........
  • Why SMART is not smart at all and doesn't properly predict disk errors that cause a kernel panic or crash


    Before getting into the output here is my typical experience with SMART, there is what I call a "bad disk" with pending and uncorrectable sectors that cannot be reallocated. It has caused a kernel panic and system crash repeatedly as we can see from the logs. But SMART says it has "PASSED" its self assessment. SMART is still useful to me but it is more about looking at Current_Pending_Sector. Any time I have had anything but 0 for that attribute it........
  • Python and BeautifulSoup4's BS4's Decompose Method To Remove Unwanted Inner Tags


    < a href="/Products/MX72244"> < span class="c-shca-icon-item__body-name-brand"> ADATA < / span> &nbs........
  • systemd management using systemctl and journalctl to check systemd logs


    systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system. The key commands or arguments you will use with systemctl are the following: Unit Commands: list-units [PATTERN...] List loaded units &nbs........
  • Linux bash shell doesn't show username, hostname or current path fix solution


    Usually this is because when you created your user you added a user but didn't create their home directory and/or for some reason your .bashrc and .bash_profile in ~ (home) is broken/missing. In your home just create the following files with the following content to solve it: .bashrc and .bash_profile. To apply it just relogin/start a new bash session # .bash_profile # Get the aliases and funct........
  • VMWare Vsphere VCSA Graphical Install Creates json


    yes it does create its own json ============================================ cat /tmp/vcsaUiInstaller/ovftool-20180809-175238948-20180809-175603497.log |grep -i json 2018-08-09T17:56:04.238-07:00 verbose OVFTool[30966] [Originator@6876 sub=Default] Manifest file entry: SHA1(VMware-vCenter-Server-Appliance-6.7.0.12000-8832884_OVF10-file1.json) = 1deb658c724767697587d5909c4051c01813e6a1 --> ........
  • Debian Mint Ubuntu compiling xmr-stak


    sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........
  • migration/4 migration 4 is using too much CPU


    top - 13:02:52 up 603 days, 19:19, 2 users, load average: 5.01, 4.15, 3.44 Tasks: 604 total, 5 running, 599 sleeping, 0 stopped, 0 zombie Cpu(s): 17.7%us, 36.1%sy, 0.0%ni, 42.0%id, 4.1%wa, 0.0%hi, 0.2%si, 0.0%st Mem: 16278908k total, 4269684k used, 12009224k free, 119672k buffers Swap: 8k total, ........
  • postfix errors fatal: no SASL authentication mechanisms /usr/libexec/postfix/smtpd: bad command startup -- throttling solution


    Jul 3 22:12:17mailserver postfix/smtpd[6195]: fatal: no SASL authentication mechanisms Jul 3 22:12:18mailserver postfix/master[4881]: warning: process /usr/libexec/postfix/smtpd pid 6195 exit status 1 Jul 3 22:12:18mailserver postfix/master[4881]: warning: /usr/libexec/postfix/smtpd: bad command startup -- throttling This only ever happens in my experience when the authentication method is actually Dovecot. Usually the problem........
  • Linux Mint Black Screen after boot no graphics solution


    This is not the normal "black screen"issue and I was shocked to eventually find out why. The normal advice of reconfiguring Xorg didn't work. Even booting into "Recovery Mode" did not help. Here is the short end of the stick that fixed it: sudo apt-get install mdm mate-desktop-environment Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled. This must be whe........
  • Intel NUC J3455 Linux Kernel freeze slowness 4.4.98 errors


    It looks like this has something to do with APIC but I am not sure. I have similar CPUs with a different MB and BIOS that work fine on the same type of kernel. A lot of time the issue is because of the C-step setting in the BIOS. The same thing happened on the 2.6 kernel with Centos 6 but this is a homebrew 4.4 kernel soI am not sure why it is happening when even Centos 7 (3.2) kernel works OK. Solution - It comes down to the BIOS set........
  • SMF Forums / Simple Machines Forums Not Displaying Images Theme or Styles Properly using 127.0.0.1


    This is one thing that has me wondering about SMF. It is apparently a known issue but in the latest version and new install nothing looked right because it was using http://127.0.0.1 to find everything! How on earth would it ever do this or think it is normal? Excerpt of crazy html code it produces that causes the issue: ........
  • Debian Mint Ubuntu Linux Server Password Forgotten Reset Password Solution Centos 7 8 Root Password Reset Recovery


    This guide will work for most modern Linux versions like Centos RHEL 7, Debian, Mint, Ubuntu etc... In Centos 7 the days of editing the "kernel"line and adding "single"are gone. On top of that sometimes after a new install passwords do not work, maybe you forgot your password or for some other reason you need to break in or fix your system? It could also be because you can't mount your root / or some other /etc/fstab error and many other err........
  • Centos How To Update to Glibc 2.14 Plus


    Centos 6 requires GLIBC 2.12 however a lot of new programs you would want to compile may need a newer glibc. You can't remove the old glibc since the whole OS is based on it but you can install the updated glibc alongside it and do an export pointing to your updated GLIBC. mkdir ~/glibc_install; cd ~/glibc_install wget http://ftp.gnu.org/gnu/glibc/glibc-2.14.tar.gz........
  • How to disable Google Fonts in Wordpress


    edit theme css: Click "Appearance -> Editor -> Stylesheet" http://yourblog.com/wp-admin/theme-editor.php?file=style.css&theme=twentysixteen textarea { color: #1a1a1a; /*font-family: Merriweather, Georgia, serif;*/ font-family: "Lucida Sans Unicode", "Lucida Grande", sans-serif........
  • linux how to answer yes to copy


    Have you have a command ask a question such as cp or move? You can do this: echo y|cp * /tmp/othercopy However it may still fail if your bashrc aliases have the "-i" flag see this post here.........
  • linux cp and mv will not overwrite due to alias!


    This through me for a loop when I would do a cp -rf or mv -f nothing would get overwritten even if piping y or yes to the command. Type alias and you'll see why: alias cp='cp -i' alias l.='ls -d .* --color=auto' alias ll='ls -l --color=auto' alias ls='ls --color=auto' alias mv='mv -i' alias rm='rm -i' The -i is a safeguard against messing things up but however does mess things up worse when you know what........
  • l2tp ipsec VPN Error Sep 12 18:16:25 vps pluto[7299]: ERROR: asynchronous network error report on eth0 (sport=500) for message to 192.5.6.2 port 20640, complainant 192.5.6.2: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated


    Sep 12 18:16:25 vps pluto[7299]: ERROR: asynchronous network error report on eth0 (sport=500) for message to 192.5.6.2 port 20640, complainant 192.5.6.2: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)] Some say changing the "leftprotoport=17/%any" will fix this but I have not found this to be the case. Essentially it means at least one end is blocking the ipsec packets. Sometimes the %any allows an alt........
  • ecryptfs how to mount or recover from a backup


    The easiest way to recover or mount an off-line ecryptfs directory is the built-in command from ecryptfs sudo ecryptfs-recover-private It will find your wrapped passphrase and ask for your password and mount it in tmp. Much easier especially when your current active OS is using ecryptfs too. This a fantastic tool when going through old backups.........
  • Centos 6.6/6.9 KVM VM Kernel Panic On Boot - Kernel panic - not syncing: Attempted to kill init!


    Iam not sure why this is happening neither the hostnode or VM changed. All I did was reboot the hostnode and startup the Centos VM again, also note it happened with the original kernel on the VM and also the latest 6.9 kernel as of this writing as shown below. Host Node: Centos 6.9 Kernel:2.6.32-696.6.3.el6.x86_64 Kernel: 2.6.32-042stab123.9 Same result in any kernel above........
  • /usr/bin/ld: cannot find -lboost_system-mt-s /usr/bin/ld: cannot find -lboost_filesystem-mt-s /usr/bin/ld: cannot find -lboost_program_options-mt-s /usr/bin/ld: cannot find -lboost_thread-mt-s collect2: error: ld returned 1 exit status make: *** [cag


    cagecoin linux compile: sudo apt-get install qt4-qmake libqt4-dev build-essential libboost-dev libboost-system-dev libboost-filesystem-dev libboost-program-options-dev libboost-thread-dev libssl-dev libdb++-dev libminiupnpc-dev Solution: sed -i s/"BOOST_LIB_SUFFIX=-mt-s"/"#BOOST_LIB_SU........
  • ffmpeg trouble concatenating similar but different files


    When things go wrong your video is basically unplayable or the first video plays fine and then freezes when moving on to the next. Generally if both videos weren't produced with the exact 100% same settings you will have issues. You can try the basic concat but it often won't work right. Solution for me: My example uses 3 videos in total so "n=3" and a=1 to include audio. ffmpeg -threads 12 -i file1.mp4 -........
  • ffmpeg Linux Mint download, compile and install howto


    #if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2 tar -jxvf ffmpeg-3.3.2.tar.bz2 cd ffmpeg-3.3.2/ ./configure --disable-yasm install prefix /usr/local source path ........
  • Migrate Centos 7 from Single HDD to mdadm RAID 10 array:


    Done on Centos 7.3 very important as clearly based on older guides it was a lot easier and more simpler! Hint do not use grub2-install! If you have trouble booting after this check this CentOS mdadm RAID booting/fixing guide. One huge caveat if you are an oldschool user or sysadmin who has avoided UEFIbooting The nor........
  • USB 3.0 External HDD Enclosure Seagate UAS problems - [sdd] tag#1 CDB: Write(16) 8a 00 00 00 00 01 70 04 08 68 00 00 00 08 00 00


    This is a 8TB Seagate external USB 3.0 device apparently newer kernels use a module called "UAS" instead of "USB Storage" which causes issues as a lot of devices are not properly supported in UAS mode by the kernel driver. The solution some say is to disable UAS specifically for your USB device but I'd rather just disable UAS altogether. Solution blacklist UAS: *do not do this it does not work and just causes your USB 3.0........
  • Openshot 2.2 is very unstable always crashing in Linux Mint 18.1!


    Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Missing folder chosen by user: Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Removed missing file: MAH02949.MP4 Jun 1 15:45:57 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: ui_util:WARNING Icon theme media-playback-start not found. Will use backup........
  • Windows 2012 Essentials r2 error - "system_thread_exception_not_handled (srv.sys)"


    I'm getting this error randomly but suspect it is an update or application conflict. It also takes ages for this "collection" to happen. "system_thread_exception_not_handled (srv.sys)"........
  • Linux how to whois query other gTLDs such as .club solution


    whois in Linux is incredibly out of date and does not seem to recognize most new TLDs domains, but there is a quick and easy tip/hack/tweak for this. An example of new TLD's site as .review .site .club whois somesite.club No whois server is known for this kind of object. bash to the rescue Now I did try to apply this in .bashrc but DONOT! Ithink the * wil........
  • ecryptfs errors


    ecryptfs-mount-private Enter your login passphrase: Inserted auth tok with sig [ee16d84] "into the user session keyring mount: No such file or directory" [ 156.118113] ecryptfs_mount: kern_path() failed [ 156.118431] Reading sb failed; rc = [-2] [ 164.233055] traps: mate-notificati[3472] trap int3 ip:7f43d7002c13 sp:7fff162c6600 error:0 [ 166.017061] ecryptfs_mount: kern_path() failed........
  • What happens when you unplug 1 or more devices from an mdadm RAID array to simulate a failure in Linux Ubuntu/Centos/Debian?


    In short the two drives in the array were /dev/sdd and /dev/sde. The kernel sees they were unplugged and have gone down as you can see below. mdadm caught the first one being unplugged /dev/sde and disabled the missing drive. However when the final drive that was part of the array is unplugged it didn't notice at all. Instead it complains about an IO error later for drives that the kernel knows do not exist anymore. [45817.162728] ata4: exception........
  • Migrating from Linux Mint 17.2 mdadm RAID array to a new one (because I upgraded to larger drives).


    1.) Replicate the number of partitions in your new drives. gdisk /dev/sda gdisk /dev/sdb I created 3 partitions of the same same size. partition #1: +1G (/boot) partition #2: +60G (swap) partition #3: rest of it (/) #note if you are using GPT/gdisk you need to create separate a partition at least 1MB in size (in my case I would a 4th partition and mark it type ef02).........
  • ERROR 2013 (HY000): Lost connection to MySQL server during query


    The solution is simple but strange, if you copy your /var/lib/mysql directory to another server and think it will work, be sure to check if you have /var/log/mysql and binary log files. If you do, the server will not work and will give you errors like below and crash without the proper log files. UPDATE user SET password=password("newpass") WHERE user='root'; flush privileges; ERROR 2013 (HY000): Lost connection to MySQL server durin........
  • bind/named rndc: connect failed: 127.0.0.1#953: connection refused (solution)


    service named status rndc: connect failed: 127.0.0.1#953: connection refused named (pid 10557) is running... This issue is normally caused by a permissions issue where named doesn't have the permissions to read the rndc.key. Check /var/log/messages: Jan 4 17:06:22 storagebox named[10753]: none:0: open: /etc/rndc.key: permission denied Jan 4 17:06:22 storagebox named[10........
  • OpenVZ Solution CPT ERR: c02fa000,73 :CPT: lock fd is closed incorrectly: 1 and vps-net_add ERROR: Unable to add route ip route add 192.168.5.2 dev venet0


    The only solution after trying many suggestions was to simply restart the "vz" service (definitely not preferable). Even doing an ifdown and ifup for venet0 did not help. ifup venet0 Bringing up interface venet0: Configuring interface venet0: net.ipv4.conf.venet0.send_redirects = 0 RTNETLINK answers: Network is down Some errors from log: CPT ERR: d2dc60........
  • blocked for more than 120 seconds issues with iowait and timeout on Live Linux distribution while writing to physical disk


    This happened while an mdadm array was syncing, all access from writing a new blank file to opening a small .txt file was very slow: [222117.312078] kjournald starting. Commit interval 5 seconds [222117.685060] EXT3-fs (md0): using internal journal [222117.685096] EXT3-fs (md0): mounted filesystem with ordered data mode [222122.376847] kjournald starting. Commit interval 5 seconds [222122.602825] EXT3-fs (md2): using internal jour........
  • How to modify HTML/Themeforest Themes to work in any path statically using unix/linux's sed command


    For themes and custom CMS setups, the typical HTML theme is not ready to go at all but here are some common sed commands (search and replace that will get most of them working without breaking as you'd expect). The problem is that often the theme directory will be separate from the content and this will break the relative paths that these themes use. sed -i s/'href="'/'href="/themes/yourtheme/'/g index.html sed -i s/'src="'/'src="/themes/y........
  • Avocent 8020 KVM Java Icedtea Viewer


    This command in Debian/Ubuntu/Mint will get everything need installed for most Java based KVM viewers: sudo apt install icedtea-netx The following additional packages will be installed: ca-certificates-java icedtea-netx-common openjdk-8-jre openjdk-8-jre-headless It seems every other updated version of Java or Icedtea breaks things and I will save the frustration of Java for another post.........
  • kernel:[14277.697049] EDAC MC0: UE row 4, channel-a= 0 channel-b= 1 labels "-": (Branch=0 DRAM-Bank=0 RDWR=Read RAS=7048 CAS=0 FATAL Err=0x4 (>Tmid Thermal event with intelligent throttling disabled))


    I am getting this error: kernel:[14277.697049] EDAC MC0: UE row 4, channel-a= 0 channel-b= 1 labels "-": (Branch=0 DRAM-Bank=0 RDWR=Read RAS=7048 CAS=0 FATAL Err=0x4 (>Tmid Thermal event with intelligent throttling disabled)) But many people believe this is a bug/false message and the server is running stably.........
  • Centos 6 how to guide convert LVM non-RAID into mdadm 1/10 RAID array live without reinstalling


    Here is the scenario you or a client have a remote machine that was installed as a standard/default minimal Centos 6.x machine on a single disk with LVM for whatever reason. Often many people do not know how to install it to a RAID array so it is common to have this problem and why reinstall if you don't need to? In some cases on a remote system you can't easily reinstall without physical or KVM access. So in this case you add a second physical or disk or already ha........
  • How To Install Linux Mint 17.2 on mdadm RAID with a separate boot partition


    Iwas surprised to see that Linux Mint at the latest 17.2 version still has NO mdadm installer option, and worse the installer will not be able to create a proper booting environment even when you do install it. How to setup mdadm in Linux mint LiveCD sudo su apt-get install mdadm # partition as you need and then create your mdadm devices # create your SWAP md0 mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/sda1 /d........
  • Centos/obfsproxy errors


    I never did get it working, it is too bad as obfsproxy should really be an option and integrated into the OpenVPN client and server or something similar: yum -y install python-pip python-devel No package python-pip available. #install the EPEL repo python-pip install obfsproxy python-pip install obfsproxy -bash: python-pip: command not found pip install obfsproxy &........
  • tar list files


    tar -ztvf flashrom.tar.gz the "z"is for gzip, if it is not gzip remove the z. If it is bzip then use "j" instead of "z" etc..........
  • Disable linux bash proxy ENV export variable


    if you type Export and see something like this: declare -x all_proxy="socks://127.0.0.1:22000/" Most sites assume and tell you to check your .bashrc or /etc/profile /etc/bash.bashrc which may not apply if you've unknowingly or forgot that you setup a proxy from your GUI such as Gnome. To check in Gnome if you have a permanent proxy do the following: System -> Settings -> Network Proxy........
  • Vbox/Virtualbox devices grayed out for non-root user solution


    It is a permissions issue that is hard to fix. All but one USB device is greyed out. I am already a member of "vboxusers" I have already enabled and disabled USB support for the guest. I have already reinstalled the latest VBOx guest editions If running as root it all works fine Changing........
  • Samsung Printer Password Login to change settings CLP


    First of all to find your IP you can hold the "X" button for a few seconds and it will print out the DHCP IP. Another way to find the IP that I prefer is to login to your router or switch and find a hostname that says something like "SEC001599CD2948" which will be your Samsung printer (at least for the C3xx or C4xx series of Samsung printers). The login and password for Samsung Syncthru Webservice:........
  • PayPal subscriptions automatically cancelling after creation of profile


    There is a weird quirk with how this works, but there is a variable called "src" that defaults to 0 or disabled if not specified as 1. The default 0 means not to recur billing on a subscription.  It's too bad it's not more obvious anywhere nor is there an explanation or warning during payment or after to both the seller and buyer. Here's a proper subscription code example that does recur and does not cancel........
  • CPanel Link to all of the command line options


    CPanel says you can access 98% of the functions through CLI which experienced Unix/Linux admins prefer for simplicity and for scripting.  I've never found CPanel easy to use from the admin panel, it seems everything is hard to find and a simple task becomes a series of hunts. So for people like me here's the list: http://cpanel.net/system-administrators/command-line-scrip........
  • drbd won't sync 8.3.13 on OpenVZ kernel


    I used the matching 8.3.13 utilities and it didn't work but strangely the newer 8.3.16 which makes DRBD complain works just fine. GIT-hash: 83ca112086600faacab2f157bc5a9324f7bd7f77 build by root@sighted, 2012-10-09 12:47:51  0: cs:SyncSource ro:Secondary/Primary ds:UpToDate/Inconsistent A r-----     ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:b oos:5236960   &am........
  • OpenVZ avoid vzctl 4.7 and ploop


    OpenVZ has made vzctl version 4.7 default to using ploop which is a big annoyance.  No one wants it otherwise we'd use Xen or KVM. Make sure to manually specify vzctl 4.6.1 or you will have issues with old scripts breaking since it defaults to using ploop (a single image like Xen/KVM). Here's a list to old versions of vzctl.........
  • Howto Convert Xen Image to KVM


    #count=10000 makes an image of 10000MB make sure your image is at least the same as your existing dd if=/dev/zero of=yourimage.img bs=1M count=10000 # losetup -fv newimage.raw # fdisk -cu /dev/loop0 # kpartx -a /dev/loop0 # dd if= of=/dev/mapper/loop0p1 # e2fsck -f /dev/mapper/loop0p1 # resize2fs /dev/mapper/loop0p1 # a lot of guides tell you to edit /etc/fst........
  • What a hdd hard drive and mdadm RAID array failure looks like in Linux


    [3805108.257042] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [3805108.257052] sd 0:0:0:0: [sda] Write Protect is off [3805108.257054] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [3805108.257066] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [3805108.257083] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [3805108.257090] sd 0:0:0:0: [sda] Write Protect is off........
  • KVM on Centos 6.3 cannot boot FreeBSD 9.2 AMD64


    On the same OS with the same kernels basically I cannot boot FreeBSD installer, I believe the issue is the host CPU. One host runs an Intel and works, while an Opteron 2373 does not work despite suggestions from this thread: http://149.20.54.209/showthread.php?t=36761 I've tried cpu options like "kvm64" "Opteron_G3" and none........
  • Linux find what processes are swapping


    Here is a handy script that will check all processes and report what is swapping #!/bin/bash for pid in `ps x|awk '{print $1}'`; do result=`cat /proc/$pid/status|grep VmSwap|awk '{print $2}'|grep -v ^"0"` if [ ! -z "$result" ]; then programresult=`ps x|grep $pid|grep -v grep` if [ $? == 0 ]; then program=`echo $programresult|awk '{print $5}'|grep -v ^grep`........
  • Migrate Linux Mint OS from one drive to another


    mount -o bind /proc /sda2/proc mount -o bind /dev/ /sda2/dev mount -o bind /sys /sda2/sys chroot /sda2 mint / # mount -o bind /proc /sda2/proc mint / # mount -o bind /dev/ /sda2/dev mint / # mount -o bind /sys /sda2/sys mint / # chroot /sda2 mint / # cd ~ mint ~ # ls Desktop mint ~ # cd / mint / # ls bin Desktop dev-temp home&nb........
  • mdadm how to add additional RAID 1 drives


    This is a great way to upgrade your RAID array or move it/copy it to a new set of hard drives. Eg. you have a current RAID 1 array on older/slower drives. Just add at least 1 of the new drives to the array, update grub/install it and then boot into it. Then you have a transparent data migration that is fully synchronized. mdadm --grow /dev/md126 --raid-devices 3 md127 : active raid1 sdc1........
  • Unixbench Testing


    The first is a dual CPU AMD Opteron 2373EE (4 cores x 2) and I think it did bad because it has some old 250GB SATAs which can only do about 65MB/s max sequential reads. I think it should have blown away the second (AMD X4 640 Quad Core). [root@fs12home unixbench-4.1.0-wht-2]# ./Run make all make[1]: Entering directory `/root/unixbench-4.1.0-wht-2' Checking distribution of files ./pgms exists ./src exists........
  • Dell FS12-NV7 2U Server Information and Guide


    I've got one of these for testing projects from work at home and got more than I bargained for with the time I've spent on it due to the storage handing/Perc 6/i cards. My particular model came with the following: 2U Rack Mount Server with Rails 2xOpteron 2373 EE (Quad Core, there is a 6-core version that can be found at times) 16GB RAM 2 x 250GB Seagate SATA 2 x Dell Perc 6/i (horrible and a nightmare to work........
  • rtorrent: symbol lookup error: rtorrent: undefined symbol: _ZN7torrent10ThreadBase8m_globalE solution


    The solution is strange but simple and works each time on Centos: yum downgrade libtorrent........
  • WD 20EARX Dead Again


    Another new drive bad from the start: Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........
  • Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO


    I'm using ecryptfs and was suddenly unable to access or even ls my home directory (but every subfolder is accessible). It just hangs and throws this message in messages/dmesg: Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO I read somewhere that perhaps some file or folder is owned by root somehow, sure enough there are some and sudoing to root allows me to........
  • WD 20EARX 2TB Bad within days


    This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad. ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0 ata1.00: irq_stat 0x40000008 ata1.00: failed command: READ FPDMA QUEUED ata1.00: cmd 60/00:00:........
  • Country List Names in HTML Select From


    This is useful for developing a lot of applications, I'm putting it here to keep it handy for myself and hopefully others: Choose CountryCanadaJapanUnited StatesUnited KingdomAfghanistan........
  • How to wipe/erase hard drives clean so data cannot be recovered for privacy reasons


    This is something many people and especially businesses worry about, or at least they should. Before throwing away a hard drive, returning a hard drive, or especially Warrantying/RMAing it, you should wipe the drive. Linux provides the "shred" and "dd" utlities which work quite well. It seems even a single pass is good enough but by default shred will do 3 passes. Here's an example of using shred in Linux (I use a custom made distribution from........
  • Ubuntu/Linux disable extra Mouse Buttons Microsoft Comfort Mouse 4500


    I find it very annoying that this mouse has buttons on the side where you grip it and the left one goes back in the browser and the right one goes forward. Imagine if you're filling out a form and hit it, most forms/websites have no protection against it. Source: http://ubuntuforums.org/showthread.php?t=2065400 Here's how I fixed it with xinput, it's too bad there's no good standard GUI to........
  • Samsung Galaxy Note I717M Canadian Version, Root and Unlock


    I chose this because I heard a lot of stories about scams and that many providers I contacted said they can't unlock the Canadian I717s (one said "my Bell server" is down). This method worked perfectly on my Bell I717M and should work for all I717 in Canada, I was able to insert a foreign SIMcard. This will work abroad too but remember entering CWM mode is different for I717's in other countries (at least theUS). Step 1 - Root + CWM........
  • Bad Hard Drive Slows Down Computer


    Here's a proven example of what a bad hard drive can do, it was technically functioning OKin a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application. The truth is that this failing 1TBHitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..). After swapping it out, tabs change instantly, emails are not lagged, and........
  • kvm cannot boot xen guest using lvm


    This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel. I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk. I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one). This is strange but it seems like this Xen PV guest has some sort of hidden or........
  • Linux Kernel Panic Messages - Symptoms of bad RAM module/stick


    These were caused by a bad stick of Corsair RAM [] free_hot_cold_page+0xfc/0x150 [] __pagevec_free+0x14/0x1a [] release_pages+0x127/0x12f [] __pagevec_release+0x15/0x1d [] __invalid_mapping_pages+0x120/0x156 [........
  • How To Test If Your Hard Drive Is Good/Signs of dying hard drive


    I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem: We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........
  • smart is not smart, it thinks a dead drive is still good


    I had a dying drive that smart thought until it totally disappeared was a good drive, and actually all parameters did look fine but this system was causing my system to lockup and other bad behavior: === START OF INFORMATION SECTION === Device Model: WDC WD20EARS-00MVWB0 Serial Number: WD-WMAZ20139 Firmware Version: 50.0AB50 User Capacity: 2,000,398,934,016 bytes Device........
  • Hitachi 2TB HDS5C3020ALA632 drive DOA


    I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead): ata1: link is slow to respond, please be patient (ready=0) ata1: softreset failed (device not ready) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: link online but device misclassified, retrying ata1: link is slow to respond, please be patient (ready=0) ata1: softreset f........
  • Kernel/make compilation time and how to improve compile times/compile the Linux kernel faster without hardware upgrades


    I thought only a faster CPUand SSDwould help but I already have a Quad-Core CPU and it wasn't being maxed out. The actual tests were performed on an AMD-V enabled 128MB dual core VMWare container though. There is a flag that can be passed to make in order to start multiple threads, by specifying 4 threads I was able to reduce the whole kernel compilation time from scratch by about 50%! (65minutes vs 31minutes!). *Yes I did do a make clean before each co........
  • mysql enable slow query logging/Query Cache Solution - find/track cause of slow mysqld/high IO/CPU usage


    If you have a webserver and find you have high IO/lagginess MySQL is one of the first things to check. It turns out MySQL was my problem and it was creating a high load on my server, especially for IO. How to Enable MySQL Slow Query Logging To Find Slow Performance/Queries vi /etc/my.cnf Add this anywhere under [mysqld] #slow queries log-slow-queries = /var/log/mysql/mysqlslowqueries.log long_query_time = 1........
  • encrypt bash scripts to hide source code


    http://www.datsi.fi.upm.es/~frosal/ SHC is a program written by the author above that does just that, it's a great little tool to have. Some have said it isn't exactly encrypting the code but just making it hard to read by obfuscating the code. There was also a good discussion about that here:........
  • Are my WDEARS20 Drives dying already?


    This happened during a RAID array check: SMART says both drives pass the test, but I'm doing a long test on them and hopefully this is not a hardware error. Apr 3 04:22:01 remote kernel: md: syncing RAID array md2 Apr 3 04:22:01 remote kernel: md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc. Apr 3 04:22:01 remote kernel: md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for reconstruction. Apr........
  • 2011 Best Laptop - HP 15.6" Laptop featuring AMD Athlon II P340 Processor (G62-420CA)


    My mother needed a new laptop and I recommended her the same one I would have bought myself or my wife, that means the cheapest possible laptop with the most features for the money. This HP shines at this price point and one thing that made me stay away from buying more and recommending HP/Compaq was the poor battery life. Not anymore, this model has an industry leading up to 4 hours of battery life. Key Factors for Choosing It: HDMI Out........
  • Santrex Review Scam Complaint - Stole My Money Fraud


    Santrex Review/Scam/Complaint Santrex never provided any working server, I believe it was just a dummy management Solus server because the server said it was booted but never connected to the console. I complained to them and eventually the support admitted the server was not working and to wait for 24 hours. I waited for 4-days, after which they sent an e-mail saying my service was being disabled for SPAM ...(when SolusVM shows 0kb of traffic). Th........
  • 95th Percentile Billing vs Usage Billing, what's better?


    There are all kinds of threads and links on the internet, and this seems to be a contentious issue butI don't know why. 95th percentile is either a good deal for some or a big rip off for others, Ijust said it there :) But the reality is that for MOST people who transfer low amounts of data but burst to higher speeds such as 40mbit+ even for short periods of time, then you'll pay a lot of money to do that. Basically 95th percentile is an-old archaic method........
  • VPS Server Scam/Review/Complaint List


    These are the only two I've encountered but here is the low-end and note my story is not at all unique. In my case I was scammed out of money and did not receive any service at all from either company. Santrex Review/Scam/Complaint Santrex never provided any working server, I believe it was just a dummy management Solus server because the server said it was booted but never connected to the console. I complained to them and eventually the support adm........
  • Enable SPAMASSASSIN on Postfix in 5 minutes


    Centos 5 Postfix and SPAMASSASSIN Tutorial yum install spamassassin chkconfig spamassassin on vi /etc/mail/spamassassin/local.cf ############## #required_hits 5 #report_safe 0 #rewrite_header Subject [SPAM] #5 is the least restrictive (means only the most obvious SPAM is caught. 0 is obviously the most restrictive/sensitive and would have lots of false positives require........
  • VOIP/Asterisk/FAX Error Problems Solution NOTICE[11389]: rtp.c:1808 ast_rtp_read: Unknown RTP codec 100 received from


    NOTICE[11389]: rtp.c:1808 ast_rtp_read: Unknown RTP codec 100 received from I've found that trying several times may work, but I also read changing your Sipura VOIP adapter settings as follows helps (but it still fails for me sometimes): In adapter change the following under SIP/Advanced Codec to G711a from G711u Passthru Method from: NSE to ReINVITE FAX CED Detect Enable: Yes FAX CNG Detect........
  • ls: error while loading shared libraries: libtermcap.so.2: cannot open shared object file: No such file or directory solution


    ls ls: error while loading shared libraries: libtermcap.so.2: cannot open shared object file: No such file or directory This is not an ldd problem or case of anything missing, this only happened after I upradedUbuntu. declare -x PATH="/home/user/bin:/usr/local/bin:/usr/bin:/bin:/usr/games" "/home/user/bin" is the problem! It's weird because I have no idea how it happened.........
  • CPU #1 not responding - cannot use it.


    I think this will be useful to others because I have a server that kept crashing mysteriously during intense disk usage/RAID checks. It would only crash during the weekly RAID integrity check. ThenI noticed during a reboot that not all CPUs were being brought up, as a result this actually creates much higher temperatures with the output I got from sensors, just booting the system produced higher than normal temperatures. You can imagine that a full blown RAID check........
  • Ubuntu 9.04 Crash


    CPU/Kernel/MB/RAID problem? Jan 5 12:45:05 testbox kernel: [653298.890004] BUG: soft lockup - CPU#0 stuck for 61s! [hal-acl-tool:4168] Jan 5 12:45:05 testbox kernel: [653298.890005] Modules linked in: vmnet vmci vmmon binfmt_misc drbd video output input_polldev ocfs2_stackglue ocfs2_dlmfs ocfs2_dlm ocfs2_nodemanager configfs k8temp hwmon_vid lp snd_hda_intel snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi........
  • Installing Webmin & Enabling SSL


    Webmin Setup Centos 5: wget http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html&ts=1294339690&use_mirror=surfnet [1] 24229 [2] 24230 [root@host ~]# --2011-01-06 21:48:20-- http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html Resolving downloads.sourceforge.net... 216.34.181.........
  • Cygwin and crontab backups via ssh/scp/rsync


    Install the "Editors" and "Net" groups that will give you rsync, ssh, ssh-keygen and cron. The trickiest thing that I keep forgetting about each time is you have to run "cron-config" which adds the cron service to Windows, and without doing that obviously no cron jobs will be run thus making automatic backups impossible. Warning about rsync/cygwin and using the -a archive switch. It's a good thing I caught this because it doesn't work ri........
  • VBulletin How To Change Welcome E-mail


    Login as Admin Languages & Phrases -> Search in Phrases Choose "Phrase Variable Name Only" Search for: welcomemail Edit the "Translation" box with what you'd like in it.........
  • WD (Western Digital) Advanced Format Drive Lagged/Slow Speed/Performance/Design Flaw EAD/EARS problem WDC WD20EARS-00S8B1


    Let the numbers speak for themselves, from what I read the Load_Cycle_Count which is very high (more than 500,000/half a million times) is the number of head parks. What a stupid"Green" design and design flaw which will probably mean an early life for the drive. This is almost as silly as Seagate's new reputation for BSY/poor quality disks since the 7200.11 series. To make it worse this is also when Western Digital introduced "Advanced Format" o........
  • VirtualBox some USB passthrough devices greyed/grayed out unavailable solution


    The solution is simple but it's a wonder why VBOX doesn't address it directly? Perhaps newer versions will but you have to add your user to the "vboxusers" group and then login and logout and you'll see the devices you wanted but couldn't access are now available. The weird thing is that the grayed out issue doesn't happen with all devcies but one notable thing is the Apple iPhone especially in DFU or Recovery Mode which is an big issue for some people.........
  • Ubuntu 10.04/GRUB2 mdadm won't boot


    Moving to RAID was a pain. What you have to do is the following from an existing install: Install mdadm Create your mdadm RAID 1 array on your spare hard drive. Start it with the missing disk. rsync the entire contents of your current / to the md partition. Here's a good way of doing it: rsync -Pha --exclude=/proc/* --exclude=/sys/* --exclude=/mnt/* /. /mnt/md2........
  • How to chroot properly into your OS/distro


    From a LiveCD or if you're doing something like converting your non-RAID install to mdadm here's how you would chroot properly (you have to mount your proc, sys and dev on the running system/LiveCD to your chroot environment if you want things to work right, especially if you need to run update-initramfs due to a driver change etc..) *replace "path" with your mount/chroot path mount -o bind /proc /mnt/path/proc mount -o bind /dev/ mnt/pa........
  • connect: No buffer space available Oct 18 12:21:03 vps kernel: printk: 177 messages suppressed. Oct 18 12:21:03 vps kernel: Neighbour table overflow.


    ping test.com connect: No buffer space available /var/log/messages Oct 18 12:21:03 vps kernel: printk: 177 messages suppressed. Oct 18 12:21:03 vps kernel: Neighbour table overflow. Solution in /etc/sysctl.conf: net.ipv4.neigh.default.gc_thresh1 = 4096 net.ipv4.neigh.default.gc_thresh2 = 8192 net.ipv4.neigh.default.gc_thresh3 = 8192 net.ipv4.neigh.default.base_reachab........
  • Local policy does not permit you to log on interactively. - Solution/Fix


    For a standalone system the solution is simple, just use the same version of Windows a copy a good version of: C:windowsSecurityDatabasesecedit.sdb from another computer. Then you should be able to login again without getting the nasty message "Local policy does not permit you to log on interactively." Of course you will probably need a way of accessing the filesystem off-line in order to get to it such as a Linux boot disc. Some........
  • jailkit for chroot ssh account security tutorial and fix for error


    This was done on Centos butI think it's easier on Debian machines, the paths that it is set to use are tailored towards Debian, so there is some fiddling that needs to be done on Centos. This is for chrooting ssh, but jailkit has other uses than just SSH jails but I won't cover them in this writeup. 1. Install jailkit yum install jailkit 2. Setup Jail Home mkdir /home/jail chown root:root /home/ja........
  • RAID 1 and Non-RAID Hard Drive Performance Comparison using tiobench


    Here is a RAID 1 partition (500GB Seagate & 2TB WD): Sequential Reads File Blk Num Avg Maximum Lat%&nbs........
  • FUSE/Curlftpfs mount ftp account as drive partition in Linux


    This is a great way to use your ftp server space, for example on your web hosting account (althoughI believe many hosts don't allow storage like this), but if you have a VPS/Dedicated Server etc.., this would be perfect. Imagine how easy it is to work with an ftp account that you can just mount as a normal partition or directory in Linux, it would be great for backups etc.. Name curlftpfs - mount a ftp host as a local directory Synopsis........
  • LUKS/cryptsetup Tutorial for Linux Hard Drive Partition Encryption


    This is based on Debian Linux but should apply equally to any *nix distro. Install LUKS/crypt-setup apt-get install cryptsetup Setup your LUKS Partition Of course change /dev/md2 with whatever partition you intend to use LUKS on. cryptsetup --verbose --verify-passphrase luksFormat /dev/md2 You'll be asked to verify your decryption password twice *DO NOT FORGET THIS PASSWORD AS IT IS NOT RECOVERABLE!........
  • Linux Centos/RHEL can't find php/apache/httpd/mysql/ftp/exim/sendmail ?


    I wasted a lot of time wondering why I could never find those packages. Check the /etc/yum.conf file and at the bottom look for the "exclude=" line. Below is what I found in mine exclude=apache* httpd* mod_* mysql* MySQL* da_* *ftp* exim* sendmail* php* bind-chroot* Just remove those entries or uncomment that line and you'll get access to the missing applications.........
  • Centos 5.5 RAID 1 boot issue


    I installed 5.5 with a 300GB RAID 1 partition (boot is also on this partition). It booted up fine the first few times until after I used a Live CD and accessed the array, and it became named /dev/md127 for some reason. Now whenI boot into CentOS I get a kernel panic and different errors, once I got "invalid superblock", even though the array is fine (it didn't happen again, probably because I was sure to dismount and stop the mdadm array properly). Here's what........
  • Unixbench Score on Core i5 750 with OpenVZ Kernel vs Xen/Openvz


    This was unbelievable how much the Xen kernel slows things down, keep in mind both tests were done on the hostnode, one was with the Openvz-Xen hybrid kernel and the other was just OpenVZ. You can see the performance difference is nearly 300% better when not using the Xen kernel. OpenVZ-Xen Kernel Test Results (I was wondering what was wrong/so slow with my Core i5!) # # # # # #&n........
  • chroot into an off-line Linux version using a LiveCD/USB


    It's not just as simple as running the chroot command, you need to ensure the /proc and /dev entries are passed through and populated to the chroot environment. Step 1 - Mount Your Off-lineOS mount /dev/sda1 /mnt Step 2 - Mount Proc mount -t proc none /mnt/proc Step 3 - Mount Dev Most guides will tell you to use this: mount -o bind /dev /mnt//dev but that doesn't work for some reason in many cases: mount: wron........
  • Seagate Drive 500GB Drive Dying


    This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device........
  • Seagate 7200.11 firmware defect in 500GB, 1000GB (1TB) and 1500GB (1.5TB) Hard Drives


    Seagate Inventory/Firmware Check I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate. *Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate! Seagate Inventory/Firm........
  • Convert HDD/Hard Drive Partition(s) into non-RAID into RAID 1 using existing data without data loss and without reformatting.


    Before we start I take no responsibility for this, you should have a backup and if you make a mistake during this process you could wipe out all of your data. So backup somewhere else before starting this as a precaution, or make sure it's data you could afford to lose. The RAID 1 Setup (Hardware Wise) I've already setup my 2 x 1TB (Seagate) drives with identical partitions, make sure your new hard drive (the empty one) is setup like your curr........
  • Picking an FTPD (vsftpd) Server in Linux Centos/Debian


    I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find. yum search ftp Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * rpmforge: ftp-stud.fht-esslingen.de * base: mirrors.netdna.com * updates: updates.interworx.info * addons: yum.singlehop.com * extras: mirrors.netdna.com rpmforge........
  • Compaq V2405CA Laptop - Unixbench Performance Test


    Here are the results, it is Sempron 3000+ AMD Mobile, 500Gig HDD, 512MB RAM with shared ATI Radeon graphics. # # # # # # # ##### ###### # # #### # # # # ## # # # #&nb........
  • PHP cannot access /usr/bin/openssl


    PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist: [code:1:1fd0f3abbe] if (!file_exists($OPENSSL)) { //echo "ERROR: OPENSSL $OPENSSL not foundn"; }[/code:1:1fd0f3abbe] I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........
  • Centos 4.3 x64 & VMWare Server Beta


    Centos 4.3 x64 & VMWare Server Beta[code:1:6d0b2c8c2f] The correct version of one or more libraries needed to run VMware Server may be missing. This is the output of ldd /usr/bin/vmware: linux-gate.so.1 => (0xffffe000) libm.so.6 => /lib/tls/libm.so.6 (0xf7fbd000) libdl.so.2 => /lib/libdl.so.2 (0xf7fb9000) libpthread.so.0 => /lib/tls/libpthread.so.0 (0xf7fa7000) libX11.so.6 => not f........
  • Updating yum repos for DAG /etc/yum.repos.d


    Updating yum repos for DAG /etc/yum.repos.dIn /etc/yum.repos.d [quote:96456b2ab9]Create any file such as "CentOS-Dag.repo" in /etc/yum.repos.d[/quote:96456b2ab9] Add the following to the above file: [code:1:96456b2ab9] [dag] name=Dag RPM Repository For Red Hat Enterprise Linux baseurl=http://dag.atrpms.net/redhat/el$releasever/en/$basearch/dag/ http://dag.freshrpms.net/redhat/e........
  • Crontab Tutorial - Tips & Shortcuts


    Crontab Tutorial - Tips & Shortcuts*/5 * * * * /command The above is an example of a command that runs every 5 minutes. Normally instead if the "*/5" you'd have to type "5,10,15,20,25,30,35,40,45,50,55" etc... You can use it to run a program every 5 days, 5 months 5 years etc...Crontab run one a day at a certain time[code:1:7a3bd32dfa]0 1 * * * /home/backupguy/databackup.sh[/code:1:7a3bd32dfa]........
  • Basic Port Listing


    Basic Port ListingHopefully someone finds this useful or at least interesting. http://www.sans.org/top20/#u9 Name Port Protocol Description Small services ........
  • Wireless/xmit power - DD-WRT v23 SP2 (09/15/06) std - build 3932 Linksys WRT54G/GL/GS


    I played around with xmit power (how much power in mW) to see if I could increase the range and signal strength. Idon't think this Linksys WRT54G's strength is the wireless, it seems to have poor signal quality and transfer rates all around. Ithink part of the problem is also that there are several wireless networks around my house that could be interfering and the walls are thick here. Anyaway, moving on now :) The default is 28mW and I increased it to........
  • Create/Enable SSL Certificates for Apache on Linux/Unix Systems eg. Redhat,Centos,Debian


    Shortcut/Easiest Way To Create A Self-Signed Key: openssl req -new -x509 -nodes -days 1530 -out server.crt -keyout server.key Using the above, you instantly create a self-signed certificate valid for 1530 days and you can simply skip to step #5.) below. If You Need a Real SSLCertificate (eg. Equifax/Openssl) then you need to create a CSR request (you'll need to follow Steps 1.) and 2.) in order to create the CSR. You then upload the CSR Certi........
  • Adventures in pre-paid SIM Cards and data GPRS/Edge/3G in China with China Mobile in Shenzhen, Guangzhou, Shanghai, Beijing and other cities


    This really is a difficult and confusing process for non-Mandarin speakers, but here's what I've done and learned so far: You can purchase an "M-Zone" China Mobile pre-paid SIMCard from almost anywhere but I tried to purchase mine from Suning (a large electronics dealer) hoping they would be able to help me or answer my questions but my plan didn't work out at all. At Suning once I found someone who spoke some English they gave me the 55 RMB M-Zone China Mobile P........
  • Unixbench Score with Glusterfs/Openvz & Quad Core Xeon - Updated with GlusterFS 2.0.8 & Optimized Client Config


    The results are still not flattering and are nothing close to native performance. Unless GlusterFS has a "DRBD-like" option to delay writes over the network and to only read from the client side, I don't see how performance can ever improve much more. After doing some client optimizations Iadded more to the score: Start Benchmark Run: Sun Nov 29 00:37:44 PST 2009 00:37:44 up 3 min, 1 user, load average: 0.01........
  • Unixbench Score with Glusterfs/Openvz & Quad Core Xeon - Updated with GlusterFS 2.0.8


    You might remember my original GluserFS/OpenVZ benchmark which produced a horrible 29.8 This is the exact same system, but using the latest 2.0.8 (with some small files patch which speeds up performance) you can see it is about 25% faster. I also haven't tuned my config files at all, but there are some settings that should increase performance on small files which I believe i........
  • Unixbench Score with Glusterfs/Openvz & Quad Core Xeon


    This is very disappointing since GlusterFS markets itself as a solution to deploy VPS servers on. On the HNitself I get a Unixbench of about 360. I'm also using an SSH tunnel to secure the communications, but even before that, things seemed very slow. # # # # # # # #####&n........
  • Linux How to Search for text within any file using Linux/Unix - Use GREP


    It's actually very simple and "grep" makes it as easy as possible. I'll outline a few common scenarios and provide some examples. Say you want to search ALLfiles within the current directory (and inside/deeper) for the text "phpinfo()" grep -R "phpinfo()" * If you want to search only certain files such as only .txt you would do this instead: grep -R "phpinfo()" *.txt As you ca........
  • Apple iPhone 3GS and predecessors are leading a revolution


    As much of a computer nerd as Iam, I'm usually a late adopter to technology for a few reasons. Ifeel most new hyped technologies and electronics are mainly fads, and I'm also cheap. Adopting later means you avoid the bugs, kinks and most importantly pay the lowest price, that's me being cheap again :) I never read much about the iPhone but Isaw all the hype around it and until recently I wasn't a big fan of anything Apple until a few years ago I realize........
  • Configuring OCFS2 Clustered File System on Debian Based Linux including Ubuntu and Kubuntu


    There's a lot of information and guides on OCFS2 for RHELand Centos Linux but the package setup and configuration is slightly different and this has thrown some people off. Installing OC2FS You should install the following packages to get started: apt-get install ocfs2-tools ocfs2console Configure OC2FS In RHEL/Centos the main configuration file is located in /etc/sysconfig/o2cb However in Debian based Linux it is located........
  • Latest Articles

  • Cloned VM/Server/Computer in Linux won't boot and goes to initramfs busybox Solution
  • How To Add Windows 7 8 10 11 to GRUB Boot List Dual Booting
  • How to configure OpenDKIM on Linux with Postfix and setup bind zonefile
  • Debian Ubuntu 10/11/12 Linux how to get tftpd-hpa server setup tutorial
  • efibootmgr: option requires an argument -- 'd' efibootmgr version 15 grub-install.real: error: efibootmgr failed to register the boot entry: Operation not permitted.
  • Apache Error Won't start SSL Cert Issue Solution Unable to configure verify locations for client authentication SSL Library Error: 151441510 error:0906D066:PEM routines:PEM_read_bio:bad end line SSL Library Error: 185090057 error:0B084009:x509 certif
  • Linux Debian Mint Ubuntu Bridge br0 gets random IP
  • redis requirements
  • How to kill a docker swarm
  • docker swarm silly issues
  • isc-dhcp-server dhcpd how to get longer lease
  • nvidia cannot resume from sleep Comm: nvidia-sleep.sh Tainted: Linux Ubuntu Mint Debian
  • zfs and LUKS how to recover in Linux
  • [error] (28)No space left on device: Cannot create SSLMutex Apache Solution Linux CentOS Ubuntu Debian Mint
  • Save money on bandwidth by disabling reflective rpc queries in Linux CentOS RHEL Ubuntu Debian
  • How to access a disk with bad superblock Linux Ubuntu Debian Redhat CentOS ext3 ext4
  • ImageMagick error convert solution - convert-im6.q16: cache resources exhausted
  • PTY allocation request failed on channel 0 solution
  • docker error not supported as upperdir failed to start daemon: error initializing graphdriver: driver not supported
  • Migrated Linux Ubuntu Mint not starting services due to broken /var/run and dbus - Failed to connect to bus: No such file or directory solution