How to convert audio for Asterisk .wav format

In our example we take "sound.mp3" and convert it to .wav. Generally Asterisk for its wave needs one audio channel (-ac 1) / mono and 8000hz (-ar 8000) instead of the standard CD/MP3 of 44100hz. Here is the command to convert into Asterisk .wav format: ffmpeg -i sound.mp3 -ac 1 -ar 8000 sound.wav Errors Asterisk may give you if the format is wrong: -- Executing [91781891@cme:3] Playback("SIP/234-000........

zfs and LUKS how to recover in Linux

Sometimes users take their removal drives and unplug and replug them to test what happens during the failure of a disk. However, this breaks things quite badly due to the /dev/mapper in LUKS not coming back online due to it not being closed. In other words, generally with non-encrypted drives the process is smooth but when encrypted you may want to follow a strategy like this: We can see below that both disks are unavailable as they were physically remov........

Migrated Linux Ubuntu Mint not starting services due to broken /var/run and dbus - Failed to connect to bus: No such file or directory solution

This is a weird issue as sometimes when upgrading or even migrating, this could happen and the reason is simple but maybe not 100% obvious at first. You will find that your GUIdoesn't load and most services fail to start, even logind Here are some errors you may see: Mar 13 22:22:23 rttbox systemd-logind[2892]: Failed to connect to system bus: No such file or directory Mar 13 22:22:23 rttbox systemd-logind........

How To Upgrade Debian 8,9,10 to Debian 12 Bookworm

Step 1.) Upgrade to Debian 11 first The process to go to Debian 12 is not as smooth as 11, when trying to upgrade from Debian 10. In fact, it doesn't work directly, so you'll first need to follow this guide to update to Debian 11, reboot and come back here if successful. Step 2.) Update sources.list Update your /etc/apt/sources.list like this: deb http://........

Docker cannot work on other overlayfs filesystems such as ecryptfs won't start overlayfs: filesystem on '/home/docker/overlay2/check-overlayfs-support130645871/upper' not supported as upperdir

This does not seem to be officially documented but makes sense that an overlay on an overlay does not work and is considered an unsupported filesystem as is even NTFS . Some admins/organizations try to use ecyptfs as a simple solution to encrypt the contents of Docker. Instead, you could probably........

How to install and configure haproxy on Linux Ubuntu Debian

haproxy is one of the best known and widely used Open Source load balancers out there and a strong competitor to nginx. haproxy is used by many large sites per Wikipedia: HAProxy is used by a number of high-profile websites including GoDaddy, GitHub,........

Stop ls in Linux Debian Mint CentOS Ubuntu from applying quotes around filenames and directory names

Later versions of ls try to be helpful and smart to prevent errors in dealing with files with spaces that were tradtionally a pain. However if you need the raw/real filenames, this can break scripts or if you are pasting into a csv etc.... How do you make ls not add the quotes? Add the capital "-N" switch ls -N You could also add an alias to make it more permanent Do this to add it to ~/........

Error opening tftp://10.0.2.2/network-confg (Permission denied) - How To Fix Cisco Router Switch Error Solution Console

How To Fix This Cisco Switch/Router Error %Error opening tftp %Error opening tftp://10.0.2.2/network-confg (Permission denied) %Error opening tftp://10.0.2.2/cisconet.cfg (Permission denied) %Error opening tftp://10.0.2.2/router-confg (Permission denied) %Error opening tftp://10.0.2.2/ciscortr.cfg (Permission denied) %Error opening tftp://10.0.2.2/network-confg (Perm........

i915 nouveau Nvidia GPU not starting lightdm Xorg failing solution for Could not determine valid watermarks for inherited state

It may appear to be an Xorg or lightdm/gdm/mdm error but in reality for many users with this issue, it's a driver conflict and issue. I had a system that had two GPUs, an Intel and Nvidia GPU. The only thing that got it working was to remove the nouveau driver and blacklist it so it never came back, then the Intel GPU works fine without these issues. Solution sudo rmmod nouveau add nouveau/other driver to blacklist edit th........

LightDM Mint Ubuntu Debian won't start errors Nvidia Graphics

This error implies that there may be an issue with Xorg or maybe your NVIDIA GPU cannot start or initialize: 35 laptop kernel: [ 2031.857704] nvidia: loading out-of-tree module taints kernel. 35 laptop kernel: [ 2031.857724] nvidia: module license 'NVIDIA' taints kernel. 35 laptop kernel: [ 2031.857725] Disabling lock debugging due to kernel taint 35 laptop kernel: [ 2031.873280] nvidia: module verification failed: signature a........

LXC Containers LXD How to Install and Configure Tutorial Ubuntu Debian Mint

If you are using mint, delete the preference that stops snap from installing (as it is required for lxc) sudo rm /etc/apt/preferences.d/nosnap.pref 1. Install lxd: sudo apt install lxd Issues install lxd or errors? Click here Debian at this time does not have lxd so you'll need to use snap: sudo apt in........

How To Enable Linux Swapfile Instead of Partition Ubuntu Mint Debian Centos

This may be necessary if you have a VM or if for some reason you just want to be more efficient with your space and have the flexibility of changing your swap space at will. What we mean is the ability to use a "swap file" or similar to the Windows "pagefile" that normally resides on the root or c: partition of Windows. Here's all you have to do and then you to can have a single partiton with everything, including the swap file on the root partition if you........

How To Create OpenVPN Server for Secure Remote Corporate Access in Linux Debian/Mint/Ubuntu with client public key authentication

Why choose OpenVPN instead of a firewall appliance? OpenVPN can be a reliable and easy replacement for traditional hardware or just be an additional tool that your company uses so that the firewall can focus on its job rather than acting as a VPNappliance at the same time. When comparing OpenVPN with traditional firewal........

Package wget is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source. E: Package 'wget' has no installation candidate. Solution

These types of errors are normally caused by misconfiguration of your /etc/apt/sources.list. In this example on Debian 10, if you didn't complete the install correctly, you will have no repos enabled and only rely on CDROM. "Package wget is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source. E: Package 'wget' ha........

Ceph Install Errors on Proxmox / How To Fix Solution

This normally happens when you interrupt the install of Ceph: pveceph install update available package list start installation Reading package lists... Done Building dependency tree... Done Reading state information... Done gdisk is already the newest version (1.0.6-1.1). ceph-common is already the newest version (15.2.15-pve1). ceph-fuse is already the newest version (15.2.15-pve1). Some package........

pulseaudio issue on QEMU/KVM guest VM when microphone is replugged/unplugged pulseaudio: pa_threaded_mainloop_lock failed pulseaudio: Reason: Invalid argument

Here is the scenario, you are using QEMU/KVM and are using something like the AC97 sound driver to pass the host audio to the guest via pulseaudio. This is useful because you can transparently pass your mic input from the host which means you can mute your microphone from the host, which prevents the guest from receiving any mic input even if unmuted. Mute / Unmute Fix This issue also seems to happen even if you press the mute button on the microphone and then unmute,........

Proxmox Guide FAQ / Errors / Howto

How To Enable HA in Proxmox Test Your HA Shutdown the node that has the HA VM. ........

CentOS 7 8 yum error Trying other mirror. To address this issue please refer to the below wiki article

The below appears at first to be a bad mirror DNS error, but if you've ruled that out you just need to clear your broken yum cache and things will be good. yum update Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * base: centos.01link.hk * extras: centos.01link.hk * updates: centos.01link.hk http://mirror.worria.com/centos/7.8.2003/os/x86_64/repodata/repomd.xml: [Errno 14] HTTP Error 404 - Not........

apcupsd how to setup and monitor APC UPS units

It really seems limited in that it can mainly give you the things you would see on the physical unit such as load etc.. wget https://downloads.sourceforge.net/project/apcupsd/apcupsd%20-%20Stable/3.14.14/apcupsd-3.14.14.tar.gz?r=https%3A%2F%2Fsourceforge.net%2Fprojects%2Fapcupsd%2Ffiles%2Flatest%2Fdownload&ts=1598115866 tar -zxvf apcupsd-3.14.14.tar.gz cd apcupsd-3.14.14 [root@somebox apcupsd-3.14.14]# ./conf........

?? Question Marks for time, permissions and size of a file?

-?????????? ? ? ? ? ? shadow ----------. 1 root root 748 Jul 10 04:35 shadow- cat: shadow: Input/output error If you see this you are probably in big trouble, it could be a physical error or if it's a VM image that it is corrupted due to a physical error on the underlying disk/array/NAS or it could a........

Ubuntu Debian Linux Cannot Install Wine Solution - wine1.6 : Depends: wine1.6-i386 (= 1:1.6.2-0ubuntu14.2) but it is not installable wine1.4 : Depends: wine1.6 but it is not going to be installed

If you've ever gotten errors like this the solution is simple, you need i386 enabled on your 64-bit install because wine depends on some 32-bit x86 libraries: dpkg --add-architecture i386 apt update apt install wine After that it will install just fine. apt install wine Reading package lists... Done Building dependency tree Reading state information... Done........

named bind errors - DNSKEY: unable to find a DNSKEY which verifies the DNSKEY RRset and also matches a trusted key for '.'

Mar 22 13:46:14 box named[31767]: validating @0x7f51bc001550: . DNSKEY: unable to find a DNSKEY which verifies the DNSKEY RRset and also matches a trusted key for '.' Mar 22 13:46:14 box named[31767]: validating @0x7f51bc001550: . DNSKEY: please check the 'trusted-keys' for '.' in named.conf. Mar 22 13:46:14 box named[31767]: error (broken trust chain) resolving './NS/IN': 192.36.148.17#53 One possibility is sometimes that your time is ou........

MySQL 5.7 on Debian and Ubuntu - How To Reset Root Password

MySQL on Debian versions is configured differently than the native local MySQL plugin so you will be disappointed when your password on the mysql client fails by default. Here is how you reset the MySQL root password the proper and "working way" #first we gracefully stop mysql sudo systemctl stop mysql; #then we forcefully kill any mysqld process just in case sudo killall -9 mysqld mysqld_safe;........

Howto Set Static IP on boot in initramfs for dropbear or other purposes NFS, Linux, Debian, Ubuntu, CentOS

This is only really necessary in the case you don't want DHCP. If you are dealing with an encrypted LUKS server on the internet, you will often want to have a static IP so you know which IP to connect to (or if you have a semi-static IP assigned by DHCP). SET IP Address by /etc/initramfs-tools/initramfs.conf IP Address=192.168.1.27 Gateway=192.168.1.1 Subnet Mask: 255.255.255.0 Hostname=myhome.com IP=192.1........

python import docx error

sudo pip3 install python-docx [sudo] password for : Downloading/unpacking python-docx Downloading python-docx-0.8.10.tar.gz (5.5MB): 5.5MB downloaded Running setup.py (path:/tmp/pip_build_root/python-docx/setup.py) egg_info for package python-docx no previously-included directories found matching 'docs/.build' warning: no previously-included files matching '.DS_Store' foun........

Cisco Unified Communications Manager / CUCM IP 8.6,10,12 Install Error Solution

Install Errors on Version 12: This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5 on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error. *Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install. What really causes this even though you successfully install........

Windows 7,8,10 and Server 2008, 2012, 2016, 2019 Read Only Attribute Won't Go Away

I have seen this in a few rare cases after a reboot, where all folders and files will have the Read Only Attribute. If you uncheck it, it will just come back. It is more of a filesystem issue in Windows than a configuration issue and it looks like when Windows detects a badly corrupted filesystem that it will make things read-only, sort of like Linux would. If you are Administrator or the owner of the folder and this is happening it is probably due to the reasoning mention........

Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM

The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........

Linux How To Disable SATA NCQ For Better Performance

This is the closest way to disabling it without using the "libata.force=noncq" kernel boot option is to set the queue to a depth of 1 which doesn't actually disable it. Change the sdc below to match the device you want to disable NCQ for. [root@officebox ~]# echo "1" > /sys/block/sdc/device/queue_depth Errors that indicate you are having a performance issue are these in messages or dmesg relating to N........

gsmartcontrol for Windows to Check the SMART S.M.A.R.T status

gsmartcontrol is a free tool that let's you see the status of the SMART parameters so you can check things like temperature, reallocated sectors, bad sectors etc.. to give you a better idea of your drive health. Download it here. gsmartcontrol is a very useful tool in Windows to check your HDD / Hard Drive health status. In my experience you should NEVER trust that everything is OK just because SMAR........

bind named error solutions named[2169]: error (no valid DS) resolving / error (broken trust chain) resolving / : error (no valid RRSIG) resolving 'com/DS/IN':

Below are the common errors you'll get with named AKA bind if your time is incorrect. The simplest solution is to install and run ntpd to correct your system's time (install ntpd if it is not installed) systemctl start ntpd systemctl enable ntpd Dec 20 13:36:16 hostingbox named[2169]: error (no valid DS) resolving 'develop.waxrain.com/A/IN': 14.215.150.17#53........

DRBD Errors Caused By Physical Corruption

In a RAID array I had a have periodically lost a drive here and there over the past several months. Iwas always able to readd and resync without losing data. However at some point it looks like some minor corruption happened and this makes DRBD unhappy. Using fsck did not help either. Dec 19 06:01:45 storageboxtest4 kernel: [19005.945890] EXT3-fs error (device drbd0): ext3_get_inode_loc: unable to read inode block - inode=22184379........

Why SMART is not smart at all and doesn't properly predict disk errors that cause a kernel panic or crash

Before getting into the output here is my typical experience with SMART, there is what I call a "bad disk" with pending and uncorrectable sectors that cannot be reallocated. It has caused a kernel panic and system crash repeatedly as we can see from the logs. But SMART says it has "PASSED" its self assessment. SMART is still useful to me but it is more about looking at Current_Pending_Sector. Any time I have had anything but 0 for that attribute it........

genisoimage errors with long filenames and deep directory structures

You'll have to violate the iso9660 standards but it is necessary if you want to preserve your filesystem and filenames and shouldn't be an issue as long as you are using a modern OS like Linux. genisoimage -o Backup-Myfiles.iso -r -J -joliet-long /some/path/ You will get errors like below (even enabling joliet-long didn't help) genisoimage: Error: /some/filename.pdf have the same Joliet name Joliet tree sort failed. The -joliet-lo........

Linux Kernel USB Export Errors

4.374647] usb_common: exports duplicate symbol usb_get_dr_mode (owned by kernel) [ 4.403334] usbcore: exports duplicate symbol __usb_get_extra_descriptor (owned by kernel) [ 4.427736] xhci_hcd 0000:00:15.0: xHCI Host Controller [ 4.427844] xhci_hcd 0000:00:15.0: new USB bus registered, assigned bus number 1 [ 4.429040] xhci_hcd 0000:00:15.0: hcc params 0x200077c1 hci version 0x100 quirks 0x01109810 [ 4.429141] xhci_hcd 0000:00:15.0: cache line size of 64 is not sup........

VMWare vSphere 6.7 Errors Solution 503 Service Unavailable (Failed to connect to endpoint:

503 Service Unavailable (Failed to connect to endpoint: [N7Vmacore4Http20NamedPipeServiceSpecE:0x00005556ba09c070] _serverNamespace = / action = Allow _pipeName =/var/run/vmware/vpxd-webserver-pipe) 503 Service Unavailable (Failed to connect to endpoint: [N7Vmacore4Http16LocalServiceSpecE:0x00007fd26000b240] _serverNamespace = /ui action = Allow _port = 5090) Errors like the above are usually because there is an issue with your vSphere or more commonly it i........

moodle install error Error reading from database

Error reading from database More information about this error It is usually not possible to recover from errors triggered during installation, you may need to create a new database or use a different database prefix if you want to retry the installation. Solution: This happened when I was running MySQL 5.1. Assuming your database details are right and the DB is up then make sure you are usin........

Ethereum Client Errors

INFO [07-19|12:11:51] Imported new block receipts count=590 elapsed=8.440s bytes=74117699 number=4870906 hash=6bc60b…934753 ignored=0 INFO [07-19|12:11:57] Imported new state entries count=499 elapsed=9.963ms processed=71076 pending=1526 retry=2&nbs........

Linux Mint 18 Screen Goes Dark or Black After Screensaver or even when using the Desktop Solution

You can search for this bug and it seems like it may be related to ecryptfs and is many years old. The symptoms are that you return to the computer and the screensaver was active or the screen was asleep/black and it doesn't seem to come back. But you check by SSH the computer is running fine and are frustrated you'll lose your running programs and have to reboot. There is a simple solution: Ctrl + Alt + F1 Ctrl +Alt + F8 Ba........

VSphere InternalServerError - Error When Adding Permissions

InternalServerError (com.vmware.vapi.std.errors.internal_server_error) => { messages = [LocalizableMessage (com.vmware.vapi.std.localizable_message) => { id = vapi.bindings.method.impl.unexpected, defaultMessage = Provider method implementation threw unexpected exception: com.vmware.vapi.std.errors.InternalServerError, args = [com.vmware.vapi.std.errors.InternalServerError] }], data = } I was getting the........

OVF Tool: Error: Task failed on server: This host does not support Intel VT-x. VMWare VCenter install On ESXi ERror

Intel VT-X is enabled in Virtualbox but it doesn't seem to pass through the needed vmx extension despite the following variables on the host confirming it is enabled: cat /sys/module/kvm_intel/parameters/nested Y cat /sys/module/kvm_intel/parameters/ept Y OVF Tool: Disk progress: 99% OVF Tool: Transfer Completed OVF Tool: Powering on VM: Embedded-vCenter-Server-Appliance- OVF Tool: Task p........

Relocating modules and starting up the kernel - VMWare ESXi 6.7 Error and Solution

I had this error in an unsupported CPUon VMWare 6.7 and apparently this sometimes works especially on older VMWare versions like 6.5 5.5 etc (but in my case it did not). To make sure it proceed when you see "Loading VMWare" Hit "Shift+O" Then add "ignoreHeadless=TRUE" See an example below:........

OpenVPN auth-user-pass-verify ENV script error

Starting with newer versions of OpenVPN Ibelieve 2.2+ you need to have "script-security 3" set or you can't execute a third party script. Prior to that you could also use the auth-user-pass-verify like this: auth-user-pass-verify ./validate.pl "$username $password $ip" via-env Options error: the --auth-user-pass-verify directive should have at most 2 parameters. To pass a list of arguments as one of the paramete........

postfix errors fatal: no SASL authentication mechanisms /usr/libexec/postfix/smtpd: bad command startup -- throttling solution

Jul 3 22:12:17mailserver postfix/smtpd[6195]: fatal: no SASL authentication mechanisms Jul 3 22:12:18mailserver postfix/master[4881]: warning: process /usr/libexec/postfix/smtpd pid 6195 exit status 1 Jul 3 22:12:18mailserver postfix/master[4881]: warning: /usr/libexec/postfix/smtpd: bad command startup -- throttling This only ever happens in my experience when the authentication method is actually Dovecot. Usually the problem........

named [FAILED] - zone 1.168.192.in-addr.arpa/IN: not loaded due to errors. - bind error solution

Centos when copying old files and restarting it seems load everything fine and then says [FAILED] with no log or other message. service restart named named [FAILED] Check more thoroughly you may have missed the error if you have lots of zones! service named restart|grep error zone 1.168.192.in-addr.arpa/IN: not loaded due to errors. zone 2.168.192.in-addr.arpa/IN: no........

Maximum number of connections from user+IP exceeded (mail_max_userip_connections=10) Dovecot Solution

This happens because Dovecot limits the maximum IMAPconnections per IPto just 10. This may be fine for a single client side IPbut if an entire office or multiple users are behind one IPor a single heavy user is active then you will get bizarre errors in your e-mail clients such as "Password Incorrect" or similar in Thunderbird. It won't be obvious on the client side as to what the problem is and they will probably just think the server is misconfi........

Linux Mint Black Screen after boot no graphics solution

This is not the normal "black screen"issue and I was shocked to eventually find out why. The normal advice of reconfiguring Xorg didn't work. Even booting into "Recovery Mode" did not help. Here is the short end of the stick that fixed it: sudo apt-get install mdm mate-desktop-environment Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled. This must be whe........

Intel NUC J3455 Linux Kernel freeze slowness 4.4.98 errors

It looks like this has something to do with APIC but I am not sure. I have similar CPUs with a different MB and BIOS that work fine on the same type of kernel. A lot of time the issue is because of the C-step setting in the BIOS. The same thing happened on the 2.6 kernel with Centos 6 but this is a homebrew 4.4 kernel soI am not sure why it is happening when even Centos 7 (3.2) kernel works OK. Solution - It comes down to the BIOS set........

How To Install Windows Server 7 8 10 12 2008 2012 2014 2016 Servers Desktops using Linux tftp, dhcpd and samba

It has been a big pain for a long-time to install Windows from a Linux environment. I used to run a windows install server and it never worked right for some reason (the install would fail on most servers). Before getting start be sure to setup your samba share so once you boot into WinPE you can mount the install for whatever Windows you want /etc/samba/smb.conf [smbwinstall] path = /tftpboot/images/winstall guest ok = yes........

Linux input/output error invalid program cannot read data on some CD-Rs and DVD-Rs on ASUS BW-16D1HT

I've never seen this before in all of my years. Ihave some very old CDs and DVDs 12-15 years old that seem not to work in this BD-R/DVD-R/CD-R Asus drive. The discs are fine actually and ironically they even work fine on a normal LG USB based BD-R drive! Here are the errors in Linux: [2914936.884924] attempt to access beyond end of device [2914936.884927] loop1: rw=0, want=730424, limit=688384 [2914954.556873] attempt to........

vbulletin 4.2.5 after upgrading from 3.6 white screen fatal php errors

The code may lead you to believe you have an incompatible template but if you are not trying to use an old template currently that is not the issue. I actually deleted all 3.x style templates to make sure. What the issue is, is old plugins that are not compatible but Vbulletin does not seem to account for this except that you'll see a fatal PHPerror. You should disable all plugins and then enable one by one until you find the one that is causing the issue. &........

[1035724.274610] [drm:intel_pipe_update_end [i915_bpo]] ERROR Atomic update failure on pipe A (start=62076478 end=62076479) time 102 us, min 894, max 899, scanline start 893, end 900 W: Possible missing firmware /lib/firmware/i915/kbl_dmc_ver1.bin

[1035724.274610] [drm:intel_pipe_update_end [i915_bpo]] *ERROR* Atomic update failure on pipe A (start=62076478 end=62076479) time 102 us, min 894, max 899, scanline start 893, end 900 W: Possible missing firmware /lib/firmware/i915/kbl_dmc_ver1.bin for module i915_bpo I've been getting those errors on a J3455 NUC box with the latest kernel on Linux Mint 18.2. When updating the initramfs I also got the error about the firmware........

How to change reserved blocks in Linux partition

user@box:~$ sudo tune2fs -l /dev/md99 [sudo] password for user: tune2fs 1.42.9 (4-Feb-2014) Filesystem volume name: Last mounted on: /mnt/md50 Filesystem UUID: 976a8655-2619-4587-878c-dab07f7b7652 Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Fi........

cudaminer freezes Linux Mint taints kernel

When running cudaminer once it tries to initialize the card the entire screen freezes. The computer itself is still running but the Xorg is done for, you cannot even switch to another console window and must reboot (even an mdm or Xorg restart does not help). At first cudaminer will give you these errors: stratrum_recv_line failed ...retry after 15 seconds GPU #0: Geforce 210 with compute ca........

imagemagick pdf convert error solution - Warning: can't process font stream, loading font by the name. Can't find CMap Identity-UTF16-H building a CIDDecoding resource. Warning: falling back to Identity ordering Error reading a conte

**** Warning: can't process font stream, loading font by the name. Can't find CMap Identity-UTF16-H building a CIDDecoding resource. Warning: falling back to Identity ordering **** Error reading a content stream. The page may be incomplete. **** File did not complete the page properly and may be damaged. **** This file had errors that were repaired or ignored. ****........

Track 01: 34 of 1726 MB written (fifo 100%) [buf 99%] 3.6x.Errno: 5 (Input/output error), write_g1 scsi sendcmd: cmd timeout after 1.897 (40) s CDB: 2A 00 00 00 44 A9 00 00 1F 00 resid: 6144 cmd finished after 1.897s timeout 40s write track da

These errors believe it or not are simply because of not being the root user or running with sudo! However if you didn't know to try as root you'd think there was a problem with your burner or disc Essentially it looks like without root you cannot send the required scsi commands to continue writing. Ithink cdrecord should have built-in tests or safeguards to see if it has the permissions to run the required commands. I guess for more advanced users the idea is simila........

strange vi errors in Linux Mint/Ubuntu line 58: E488: Trailing characters: t_Sbet line 63: E171: Missing :endif

This happens on any file an even just typing "vi"whereas it never happened before. I suspect an update or environment variable is causing this issue When entering vi I get this weird stuff line 58: E488: Trailing characters: t_Sbet line 63: E171: Missing :endif When exiting vi I get this weird stuff t_Sb=^[[4%?%p1%{1}%=%t........

Linux shows my drive as being dead is it really? Buffer I/O error on device sdb, logical block 0 sd 3:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00

Normally the below would indicate a failing or failed drive. In this case the SATA port was unplugged and sometimes the Linux kernel/motherboard even with AHCIjust don't play nice and can't handle it. What happened is Iplugged in a new drive after removing another one. However the log shows that after the old drive was plugged in the Linux kernel kept complaining thinking the drive was there but not responding properly. This continued even with reseating........

How to convert xlsx/xls Excel file into csv

A lot of times these files seem to lag and be incredibly slow even if just a few dozens rows of data. Here is how you can convert it with "gnumeric": ssconvert file.xlsx file.csv You may get lots of weird errors like this but the conversion seems to work fine: (ssconvert:15244): GLib-GObject-WARNING **: g_object_set_valist: object class 'SheetObjectImage' has no property named 'style'........

ecryptfs errors

ecryptfs-mount-private Enter your login passphrase: Inserted auth tok with sig [ee16d84] "into the user session keyring mount: No such file or directory" [ 156.118113] ecryptfs_mount: kern_path() failed [ 156.118431] Reading sb failed; rc = [-2] [ 164.233055] traps: mate-notificati[3472] trap int3 ip:7f43d7002c13 sp:7fff162c6600 error:0 [ 166.017061] ecryptfs_mount: kern_path() failed........

Migrating from Linux Mint 17.2 mdadm RAID array to a new one (because I upgraded to larger drives).

1.) Replicate the number of partitions in your new drives. gdisk /dev/sda gdisk /dev/sdb I created 3 partitions of the same same size. partition #1: +1G (/boot) partition #2: +60G (swap) partition #3: rest of it (/) #note if you are using GPT/gdisk you need to create separate a partition at least 1MB in size (in my case I would a 4th partition and mark it type ef02).........

yum Packages skipped because of dependency problems:

Solution: yum -y install --skip-broken package-you-want-to-install Packages skipped because of dependency problems: php56w-mysql-5.6.30-1.w6.x86_64 from webtatic Error: Multilib version problems found. This often means that the root cause is something else and multilib version checking is just pointing out that there is........

ERROR 2013 (HY000): Lost connection to MySQL server during query

The solution is simple but strange, if you copy your /var/lib/mysql directory to another server and think it will work, be sure to check if you have /var/log/mysql and binary log files. If you do, the server will not work and will give you errors like below and crash without the proper log files. UPDATE user SET password=password("newpass") WHERE user='root'; flush privileges; ERROR 2013 (HY000): Lost connection to MySQL server durin........

ioncube loader install howto on PHP/Centos

Disclaimer, before starting this I do not like ioncube, it is great to protect your source code, but a big pain to setup this extension since it has to be done manually. Further, fi you do a PHPupdate ioncube may no longer work, causing important sites or services to not work (I wish authors would take another approach). 1.) Download from here:https://www.ioncube.com/loaders.php 2.) Extract the contents and co........

OpenVZ Solution CPT ERR: c02fa000,73 :CPT: lock fd is closed incorrectly: 1 and vps-net_add ERROR: Unable to add route ip route add 192.168.5.2 dev venet0

The only solution after trying many suggestions was to simply restart the "vz" service (definitely not preferable). Even doing an ifdown and ifup for venet0 did not help. ifup venet0 Bringing up interface venet0: Configuring interface venet0: net.ipv4.conf.venet0.send_redirects = 0 RTNETLINK answers: Network is down Some errors from log: CPT ERR: d2dc60........

possible SYN flooding on port 80. Sending cookies.

Errors like this are shown on high usage servers and ports so it is common to see it on http and even imap ports: possible SYN flooding on port 80. Sending cookies. The Linux kernel will even detect flooding on OpenVZ containers: possible SYN flooding on ctid 6000, port 993. Sending cookies. In many cases this is not an issue and is more so simply a result of regular, but high usage traffic.........

Centos and obfsproxy install errors

pip install obfsproxy /usr/lib/python2.6/site-packages/pip/_vendor/requests/packages/urllib3/util/ssl_.py:90: InsecurePlatformWarning: A true SSLContext object is not available. This prevents urllib3 from configuring SSL appropriately and may cause certain SSL connections to fail. For more information, see https://urllib3.readthedocs.org/en/latest/security.html#insecureplatformwarning. InsecurePlatformWarning You are using pip version 7.1.0, however version 8.1.1 i........

Errors were found while checking the disk drive for /.

Iwill start by saying I think I know what caused this boot-time error on Linux Mint but should also apply to Debian and Ubuntu. I changed my BIOS time to several hours in the past to match the current time, but this caused Linux to think there were incorrect filesystem times. The problem is that it seems when you hit this I am not sure what is happening, it doesn't seem to be doing fsck and hangs without prompting the user. What I have found is that........

Avocent 8020 KVM Java Icedtea Viewer

This command in Debian/Ubuntu/Mint will get everything need installed for most Java based KVM viewers: sudo apt install icedtea-netx The following additional packages will be installed: ca-certificates-java icedtea-netx-common openjdk-8-jre openjdk-8-jre-headless It seems every other updated version of Java or Icedtea breaks things and I will save the frustration of Java for another post.........

tsclient (Terminal Server RDP Client) missing in Debian, Ubuntu, Linux Mint

This was a horrible shock after upgrading fromUbuntu 9 to Linux Mint 17 and I found that the last distro to support tsclient was Debian Squeeze. For some reason it has disappeared for a long time and the new options such as rdesktop and gnome-rdp do not have any start menu entry and just aren't done as well as tsclient. Fortunately there is a solution: tsclient surprisingly can be downloaded as a direct .deb package and it fails with some variou........

Debian 8 Jessie in Linux OpenVZ Container does not work on Centos host

It sounds like this is corrected in later versions of the OpenVZ kernel but Iam not sure, it may also be that a much newer kernel is needed and Centos may not have a recent enough kernel. *Debain 7.0 however does work fine as a temporary fix or work around. Debian 8 OpenVZ no IP and networking not working: lo Link encap:Local Loopback ........

Virtualbox errors on Ubuntu/Debian/Mint

The solution was to reinstall the vbox dkms package and do a manual modprobe of the modules it makes. I never sorted out the unable to start due to the USB issue, I did have the guest additions installed but the only way to boot was to change the pointing device from USB to PS2 and then to disable the USB controller (if your pointing device is set as USB, disabling USB will not work because it will re-enable by default when it sees your pointing device is USB, this is w........

status: { DRDY ERR } error: { ICRC ABRT } failed command: WRITE FPDMA QUEUED MCP55 Linux Errors

[ 2868.041375] ata1: EH in SWNCQ mode,QC:qc_active 0x40 sactive 0x40 [ 2868.041554] ata1: SWNCQ:qc_active 0x40 defer_bits 0x0 last_issue_tag 0x6 [ 2868.041556] dhfis 0x40 dmafis 0x40 sdbfis 0x20 [ 2868.041874] ata1: ATA_REG 0x41 ERR_REG 0x84 [ 2868.042013] ata1: tag : dhfis dmafis sdbfis sactive [ 2868.042163] ata1: tag 0x6: 1 1 0 1 [ 2868.042301] ata1.00: exception Emask 0x1 SAct 0x40 SErr 0x400000 action 0x6 frozen [........

Firefox errors Unable to generate public/private key pair. (Error code: sec_error_keygen_fail)

Your firefox is out of date if you get errors like below: Secure Connection Failed ........

Centos/obfsproxy errors

I never did get it working, it is too bad as obfsproxy should really be an option and integrated into the OpenVPN client and server or something similar: yum -y install python-pip python-devel No package python-pip available. #install the EPEL repo python-pip install obfsproxy python-pip install obfsproxy -bash: python-pip: command not found pip install obfsproxy &........

flypro EEPROM PLCC32 programmer software error "The device ID does not match, whether to continue operating"

If you get that message it means you have inserted the adapter or device incorrectly. In my case the adapter needed to be at the rear end of the pins and it caused this message. Do not ignore this message as it may appear to work but you will get errors and in reality your chip will not be erased or programmed even if it appears like it is working.........

ECC Errors in action

Message from syslogd@server at Sep 14 11:35:59 ... kernel:[Hardware Error]: MC4 Error (node 1): DRAM ECC error detected on the NB. Message from syslogd@server at Sep 14 11:35:59 ... kernel:[Hardware Error]: Error Status: Corrected error, no action required. Message from syslogd@server at Sep 14 11:35:59 ... kernel:[Hardware Error]: CPU:6 (10:8:0) MC4_STATUS[Over|CE|MiscV|-|AddrV|CECC]: 0xdc00400021080813........

Weird Ubuntu Issues with NVIDIA driver/Compiz

1.) My screensaver would take a long time to disable after hitting a key. 2.) Usually errors like below will follow. 3.) Compiz sometimes uses 100% or high CPU 4.) My window controls will disable (eg. the minimize, maximize and close buttons). It seems like Compiz or appearance/effects disable themselves. Re-enabling Desktop Effects under Appearance temporarily fixes it. 5.) high load in general from things like "Migration" pr........

HP Procurve Switch 2824 CLI Telnet Experience , Guide and Tutorial

------------------------------------- ProCurve J4903A Switch 2824 Software revision I.10.77 Copyright (C) 1991-2009 Hewlett-Packard Co. All Rights Reserved. RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by the Government is subject to restrictions........

Linux Kernel EDAC errors EDAC MC0: UE row 0, channel-a= 0 channel-b= 1 labels "-": NON-FATAL recoverable (Branch=0 DRAM-Bank=0 Buffer ID = 0 RDWR=Read RAS=0 CAS=0 NON-FATAL recoverable Err=0x800 (Non-Aliased Uncorrectable Patrol Data ECC))

I'm not sure why I'm getting these but all memory modules are the exact same and all passed memtest successfully although they are ECC. I've heard that ECC RAM can't be tested as well and the kernel seems to indicate they are non-fatl recoverable errors. I wonder if the BIOS has aggressive RAM timing or maybe the controller or motherboard is bad. [ 12.716515] EDAC MC: Ver: 2.1.0 [ 12.717771] EDAC MC0: Giving out device to........

esniper and curl errors https://signin.ebay.com/ws/eBayISAPI.dll?SignIn: Couldn't connect to server: couldn't connect to host

I kept thinking it was esniper but somehow my bash settings have a preset proxy that was creating the issue. https://signin.ebay.com/ws/eBayISAPI.dll?SignIn: Couldn't connect to server: couldn't connect to host curl manually to any URL is the same: curl: (7) couldn't connect to host Run curl with -vvvvvv mode to see the issue: curl -vvvvvvvvvv http://realtechtalk.com * About to c........

Postfix Errors & Solutions "unprivileged": bad value: "???" - bad transport type:

Aug 25 16:43:24 evohostingtor postfix/master[19471]: fatal: /etc/postfix/master.cf: line 24: field "unprivileged": bad value: "???" Solution: I had the wrong thick dashes when c&ping (just retype them with your keyboard) Aug 25 16:47:10 mailbox postfix/master[24498]: fatal: /etc/postfix/master.cf: line 25: bad transport type: syslog_name=postfix/auth-cleanup auth-cleanup unix n - - - 0 cleanup #-o syslog_name=postfix/........

Postfix how to secure outgoing authenticated e-mails for privacy and hide the IP address, mailer and other things

The most common solution is to use the /etc/postfix/header_checks but this is a big problem. Why is header_checks a problem? Because it does it to all mail whether incoming or outgoing and whether authenticated or not. We of course want as much header information for incoming as we can get for many reasons but many organizations want to secure and make their mail clients as secure as possible. I adapted this solution to the client's custom config, they are configur........

mytop install errors

mytop-1.4-2.el5.rf.noarch from rpmforge has depsolving problems --> Missing Dependency: perl(DBI) is needed by package mytop-1.4-2.el5.rf.noarch (rpmforge) solution: #disabling excludes is required on CPanel type boxes which exclude most updates including perl-DBI yum --disableexcludes=main install perl-DBI mytop-1.4-2.el5.rf.noarch from rpmforge has depsolving problems --> Missing Dependency:........

drbd won't create device if previous partition is on it Command 'drbdmeta 0 v08 /dev/md160 internal create-md' terminated with exit code 40

This is what fixed it: [root@box13 ~]# dd if=/dev/zero of=/dev/md160 bs=512 count=500 Basically you need to wipe out more than just the 512 byte partition table so 512 bytes * 500 is more than enough to make DRBD happy and think the partition is now empty. The reason this happens is because it gets confused when there is a previous partition with data on the device you are using. root@box13 ~]# d........

heatbeat ERROR: NV failure (msgfromsteam): [>>> ] ha_msg_add_nv_depth: line doesn't contain '='

Apr 17 11:55:47 Cluster01 heartbeat: [1426]: WARN: ha_msg_add_nv_depth: line doesn't contain '=' Apr 17 11:55:47 Cluster01 heartbeat: [1426]: info: >>> Apr 17 11:55:47 Cluster01 heartbeat: [1426]: ERROR: NV failure (msgfromsteam): [>>> ] I have never been able to reproduce the above but it happened on heartbeat-3.04-2 when Itook a node down for testing. One thing Ibelieve caused it was by configuring ha.cf........

drbd won't sync 8.3.13 on OpenVZ kernel

I used the matching 8.3.13 utilities and it didn't work but strangely the newer 8.3.16 which makes DRBD complain works just fine. GIT-hash: 83ca112086600faacab2f157bc5a9324f7bd7f77 build by root@sighted, 2012-10-09 12:47:51 0: cs:SyncSource ro:Secondary/Primary ds:UpToDate/Inconsistent A r----- ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:b oos:5236960 &am........

heartbeat compile errors with rpmbuild

c1: warnings being treated as errors stonith_signal.h:34: error: 'stonith_signal_set_simple_handler' defined but not used gmake[3]: *** [apcmaster.lo] Error 1 gmake[3]: Leaving directory `/root/rpmbuild/BUILD/heartbeat-1.2.4/lib/plugins/stonith' gmake[2]: *** [all-recursive] Error 1 gmake[2]: Leaving directory `/root/rpmbuild/BUILD/heartbeat-1.2.4/lib/plugins' gmake[1]: *** [all-recursive] Error 1 gmake[1]: Leaving directory `/root/rpmbuild/BUI........

NVIDIA GeForce GT 610 not working in Linux solution - use older 304.117 driver

Iused the slightly older "304.117" version and it worked. With the newest version Icouldn't get X to start and kept getting these errors in messages/dmesg. [ 2346.083660] nvidia 0000:01:00.0: irq 44 for MSI/MSI-X [ 2350.608342] NVRM: RmInitAdapter failed! (0x12:0x2b:1831) [ 2350.608354] NVRM: rm_init_adapter failed for device bearing minor number 0 [ 2350.608369] NVRM: nvidia_frontend_open: minor 0, module->open() failed, err........

[Hardware Error]: CPU:0 MC4_STATUS[-|CE|MiscV|-|AddrV|CECC]: 0x9c054c84011c011b [Hardware Error]: cache level: L3/GEN, tx: GEN, mem-tx: RD [Hardware Error]: Northbridge Error (node 0): L3 data cache ECC error.

This server has been running for weeks without issue, it's currently only using 1 of 2 CPUs as it is running in the office as a test bed (mainly due to the handle 12 bay storage/great for testing HDDs). The errors below seem to mainly be from AMD CPUs, it's only happened a single time and in the days since Igot that error it hasn't occurrred. Interestingly enough /proc/cpuinfo still shows all 4 cores of the CPU (Opteron 2373 Quadcore HE) and the functionality doesn't seem........

CPanel Log File Locations for access_log,error_log, mysql

All Errors (CPanel does not report by domain, but puts everything in a single log which Ithink is a bit silly and annoying): /usr/local/apache/logs/error_log Access_Logs They are found within the home directory of the site user eg.: /home/admin/access-logs/yoursite.com MySQL Logs /var/lib/mysql/yourhostname.err........

strange kernel dmesg errors

Sep 26 16:56:21 box kernel: 00 00 00 00 00 00 00 00 Sep 26 16:56:21 box kernel: [37007.155690] d_alias libdl-2.12.so d_count=9 d_flags=8 Sep 26 16:56:21 box kernel: [37007.155697] 09 00 00 00 08 00 00 00 9f 05 9f 05 00 00 00 00 c0 71 1d 18 04 88 ff ff 00 00 00 00 00 00 00 00 a0 7e 48 00 00 c9 ff ff 78 a9 21 18 04 88 ff ff 3a 7b fa 4e 0d 00 00 00 98 5c 2d 18 04 88 ff ff 18 5c 2d 18 04 88 ff ff 18 5c 2d 18 04 88 ff ff 00 01 10 00 00 00 ad de 00 02 20 00 00 00 ad de f8........

LSI MegaRAID Adventures, Guide and HowTo

LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........

EXT4-fs error (device md20): ext4_add_entry: bad entry in directory #2552670:

Jun 12 10:30:53 kernel: [724514.291670] EXT4-fs error (device md20): ext4_add_entry: bad entry in directory #2552670: rec_len % 4 != 0 - offset=216, inode=2553603, rec_len=94, name_len=84 Jun 12 10:30:53 kernel: [724514.292400] EXT4-fs error (device md20): ext4_add_entry: bad entry in directory #2552670: rec_len % 4 != 0 - offset=216, inode=2553603, rec_len=94, name_len=84 This happened when an unprivileged user was backing up a Windows filesystem, once they ha........

WD 20EARX Dead Again

Another new drive bad from the start: Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........

WD 20EARX 2TB Bad within days

This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad. ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0 ata1.00: irq_stat 0x40000008 ata1.00: failed command: READ FPDMA QUEUED ata1.00: cmd 60/00:00:........

eth0 changed to eth1 or eth2 and the solution to fix it

If you move your hard drive(s) around to other computers/servers, you'll find that your eth0 keeps getting higher, the first time it will become eth1 and then eth2 etc and even higher if your server has dual or quad NICs. The reason is that udevd basically assigns eth0 tot he first NIC it finds and remembers it, if it encounters a NIC with a differentMAC, it assigns it one higher (eg. eth1). See the example below, I have eth2 now so how doI fix it?........

Directadmin Log File Locations

This is a handy link and list of all the relevant Directadmin log files and related servers. http://help.directadmin.com/item.php?id=11 DirectAdmin: /var/log/directadmin/error.log /var/log/directadmin/errortaskq.log /var/log/directadmin/system.log /var/log/directadmin/security.log Apache:........

Bad Hard Drive Slows Down Computer

Here's a proven example of what a bad hard drive can do, it was technically functioning OKin a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application. The truth is that this failing 1TBHitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..). After swapping it out, tabs change instantly, emails are not lagged, and........

badblocks in Linux to check/verify if a hard drive/HDD is good or bad

I like badblocks and don't know a better more reliable way of checking the drive. If there are no errors from badblocks and dmesg doesn't produce any SATA related errors, the drive should be good (for now at least). I also prefer to do read and write mode, yes it takes ages but it is really the best way of doing it. This gives me the most confidence in knowing that a drive, especially a new one is at least OK at the moment. To test in read only mode........

Setup PXE Boot using Centos and dhcpd, tftp and syslinux

This is something I often setup for clients because it's very helpful for people in datacenters, this allows custom OS installs on demand, you can customize it more by using kickstart etc.. but here's a base I use before customizing more: This little script below will install everything you need to get booting by PXE Linux. It also assumes you set a local IP (be sure not to overwrite your existing IP) on eth0:0 (note the :0) as 192.168.1.10 and it........

xen how to resize an image properly

The best way I could figure out is to use another guest of some sort to do this, while assigning the disk that needs to be resized to the same guest. So say we have /dev/xvda as the guests drive and we've booted it up. We also have /dev/xvdb (this is going to be the image/disk to be resized). In this case it's based on an ext3/4 image. Run e2fsck on it to ensure there are no filesystem errors. e2fsck /dev/xvdb........

Linux Ubuntu Nvidia GT430 Lockups/Errors/Freezes NVRM: os_schedule: Attempted to yield the CPU while in atomic or interrupt context

I'm running Ubuntu 10.10 with Asus NVIDIA GT430 2.6.35-32-generic-pae #65-Ubuntu SMP Tue Jan 24 14:06:16 UTC 2012 i686 GNU/Linux Nvidia binary driver: 260.19.06 The screen sometimes completely freezes and locks up or everything starts going very slow: [1903398.100007] NVRM: os_schedule: Attempted to yield the CPU while in atomic or interrupt context [1903402.373210] NVRM: Xid (0001:00): 53, CMDre 00000000 00000080 00000000 00000005 00........

KVM QEMU and Xen how to mount disk images off-line and access data

fdisk -lu VPS.img last_lba(): I don't know how to handle files with mode 81ed You must set cylinders. You can do this from the extra functions menu. Disk VPS.img: 0 MB, 0 bytes 255 heads, 63 sectors/track, 0 cylinders, total 0 sectors Units = sectors of 1 * 512 = 512 bytes Device Boot Start End ........

Xen non-HVM container won't work/boot anymore

One of my test Centos 5 containers was on a partition that filled up and it threw all sorts of errors and stopped responding but now I can't boot it again anymore. All the console shows is the Linux Penguin on the top left corner and the xm console says "usbcore: registered new driver hub" and has halted there. Centos 5 Xen container stuck/frozen won't boot on "usbcore: registered new driver hub" Another great way of troubleshooting is booting fro........

mdadm/Debian problem

This is one in a series of weird things whichIthought was motherboard related (I RMA'd the motherboard), the RAM tests fine with memtest86 and I used badblocks on both RAID 1 members with no errors and smartctl is happy with them. Basically the array crashes the kernel a lot and has issues when writing. [112322.723465] md0: rw=0, want=14958668696, limit=1887460480 [112322.731077] attempt to access beyond end of device [112322.731087] md........

samba/smbd connection to share problems and solutions

I'll start by showing some problems in the logs: [2011/08/07 16:22:06, 0] param/loadparm.c:8569(process_usershare_file) process_usershare_file: stat of /var/lib/samba/usershares/movie failed. Permission denied [2011/08/07 16:22:06, 1] smbd/service.c:676(make_connection_snum) create_connection_server_info failed: NT_STATUS_ACCESS_DENIED That means you don't have permission to access the fi........

How To Test If Your Hard Drive Is Good/Signs of dying hard drive

I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem: We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........

smart is not smart, it thinks a dead drive is still good

I had a dying drive that smart thought until it totally disappeared was a good drive, and actually all parameters did look fine but this system was causing my system to lockup and other bad behavior: === START OF INFORMATION SECTION === Device Model: WDC WD20EARS-00MVWB0 Serial Number: WD-WMAZ20139 Firmware Version: 50.0AB50 User Capacity: 2,000,398,934,016 bytes Device........

Openvz YUM Error Solution to "[Errno -1] Metadata file does not match checksum Trying other mirror."

It's weird because I have a nearly identical box and setup and I can update the ovzkernel-PAE* just fine but on this box it doesn't work. I only get this error with the openvz.repo and not others such as Centos-Base.repo With my other server it works normally: ================ Setting up Update Process Resolving Dependencies --> Running transaction check ---> Package ovzkernel-PAE.i686 0:2.6.18-238.12.1.el5.0........

Hitachi 2TB HDS5C3020ALA632 drive DOA

I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead): ata1: link is slow to respond, please be patient (ready=0) ata1: softreset failed (device not ready) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: link online but device misclassified, retrying ata1: link is slow to respond, please be patient (ready=0) ata1: softreset f........

Kernel/make compilation time and how to improve compile times/compile the Linux kernel faster without hardware upgrades

I thought only a faster CPUand SSDwould help but I already have a Quad-Core CPU and it wasn't being maxed out. The actual tests were performed on an AMD-V enabled 128MB dual core VMWare container though. There is a flag that can be passed to make in order to start multiple threads, by specifying 4 threads I was able to reduce the whole kernel compilation time from scratch by about 50%! (65minutes vs 31minutes!). *Yes I did do a make clean before each co........

SPAMASSASSIN/spamcd solution - spamc[16225]: connect to spamd on 127.0.0.1 failed, retrying (#2 of 3): Connection timed out

May 6 08:16:57 devbox spamc[16225]: connect to spamd on 127.0.0.1 failed, retrying (#2 of 3): Connection timed out May 6 08:17:02 devbox spamc[20214]: connect to spamd on 127.0.0.1 failed, retrying (#1 of 3): Connection timed out spamc[16225]: connect to spamd on 127.0.0.1 failed, retrying (#3 of 3): Connection timed out First make sure that the spamd service is actually running, this is your spamd (spamassassin server) cannot be reached. In my c........

phpMyAdmin - Error Cannot start session without errors, please check errors given in your PHP and/or webserver log file and configure your PHP installation properly.

The fix for this was setting the correct permissions in /var/lib/php, it needs to be "root.root" And /var/lib/php/session needs to be "root.apache" to work properly. After that I was able to login to phpMyAdmin as normal. This whole thing happened because I accidentally changed all of /var/lib to root.root.........

MYSQL Error Can't find file: './wf/Sessions.frm' (errno: 13) Solution

mysql errors even though these files do exist: 110405 13:21:37 InnoDB: Operating system error number 13 in a file operation. InnoDB: The error means mysqld does not have the access rights to InnoDB: the directory. InnoDB: File name ./ibdata1 InnoDB: File operation call: 'open'. InnoDB: Cannot continue operation. 110405 13:26:15 InnoDB: Operating system error number 13 in a file operation. InnoDB: The error means my........

Dying Samsung DVDRW Drive

My Samsung drive failed on me, at first I thought it was the enclosure but a direct SATA connection causes the same problems for discs that are inserted. It will work fine for a few minutes but then starts spewing the errors below. I've never been a fan of Korean made optical drives and have always had trouble with them. The problem is that I don't believe NEC and Lite-ON make drives anymore, and I considered them the leaders. Apr 7 11:58:48 bo........

Drupal 6.2 Install and how to move install to root/non-subdirectory

drup 6.2 install $cd drupgoodinst3883/ [ drupgoodinst3883]$ ls CHANGELOG.txt cron.php index.php INSTALL.pgsql.txt INSTALL.txt MAINTAINERS.txt modules robots.txt sites update.php xmlrpc.php COPYRIGHT.txt includes INSTALL.mysql.txt install.php LICENSE.txt misc&........

ls: error while loading shared libraries: libtermcap.so.2: cannot open shared object file: No such file or directory solution

ls ls: error while loading shared libraries: libtermcap.so.2: cannot open shared object file: No such file or directory This is not an ldd problem or case of anything missing, this only happened after I upradedUbuntu. declare -x PATH="/home/user/bin:/usr/local/bin:/usr/bin:/bin:/usr/games" "/home/user/bin" is the problem! It's weird because I have no idea how it happened.........

mdadm/md-check how to check array integrity without rebuilding

This doesn't seem to be widely known (maybe it's in some documentation that none of us read though)but there's an easy way to check the integrity of any mdadm array: sudo echo check > /sys/block/md0/md/sync_action -bash: /sys/block/md0/md/sync_action: Permission denied sudo will never work, this only works as root since echo is not actually a binary/command. It is built-into bash. /sys/devices/virtu........

Cygwin and crontab backups via ssh/scp/rsync

Install the "Editors" and "Net" groups that will give you rsync, ssh, ssh-keygen and cron. The trickiest thing that I keep forgetting about each time is you have to run "cron-config" which adds the cron service to Windows, and without doing that obviously no cron jobs will be run thus making automatic backups impossible. Warning about rsync/cygwin and using the -a archive switch. It's a good thing I caught this because it doesn't work ri........

rsync preserve attributes, permissions/ownership and times without being root non-root user

One of the purposes of rsync is to backup whole filesystems and archive them but how can you do that properly and restore things to normal if all permissions and ownerships are not preserved from your root filesystem? It's not desirable to have everything running as root, especially not just for an rsync. The Easy rsync preserve permission solution for non-root users sudo is the answer and all you have to do is edit /etc/sudoers At the end o........

Ubuntu/Debian DRBD 8.0 Setup Guide

I've only used it on Centos, soI thought I'd make a quick Debian guide: Install the DRBD Package apt-get install drbd8-utils Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: libswfdec-0.8-0 Use 'apt-get autoremove' to remove them. The following........

mdadm won't boot due to fsck error

Nov 29 20:17:58 ubuntu kernel: [ 1157.180789] md: md1 stopped. Nov 29 20:17:58 ubuntu kernel: [ 1157.180829] md0: unknown partition table filesystem not responding/reading properly with du or rsync (this needed an fsck). [ 2571.489217] EXT3-fs error (device md2): ext3_lookup: deleted inode referenced: 35923106 [ 2571.942299] EXT3-fs error (device md2): ext3_lookup: deleted inode referenced: 35923110 [ 2571.9568........

OpenVZ iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. Solution

This error is annoying, in a Virtuozzo KB entry about this ip tables nat problem they say the kernel needs to be ugpraded: Symptoms The node runs 2.6.18-x kernel older than 2.6.18-028stab053.10. NAT module does not work in container, you get "can't initialize iptables table 'nat'" error: # iptables -t nat........

Centos 5.5 RAID 1 boot issue

I installed 5.5 with a 300GB RAID 1 partition (boot is also on this partition). It booted up fine the first few times until after I used a Live CD and accessed the array, and it became named /dev/md127 for some reason. Now whenI boot into CentOS I get a kernel panic and different errors, once I got "invalid superblock", even though the array is fine (it didn't happen again, probably because I was sure to dismount and stop the mdadm array properly). Here's what........

rsync ERROR: sdb2/backup.r18 failed verification -- update retained.

ERROR: sdb2/backup.r18 failed verification -- update retained. This happened when Iwas rsyncing a dying hard drive, a lot of people seem to report this as an error with rsync itself but I don't think rsync is the issue at all. I know the source hard drive was bad, it was having all kinds of timeout, seek, hardware ECC recovered and reset errors. The only time something else could be the problem is if the data is being corrupted in transit, perhaps through........

Seagate Drive 500GB Drive Dying

This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device........

Seagate 7200.11 firmware defect in 500GB, 1000GB (1TB) and 1500GB (1.5TB) Hard Drives

Seagate Inventory/Firmware Check I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate. *Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate! Seagate Inventory/Firm........

Linux AHCI Hotswap Tips - Remember To Reread The Partition Table WITHOUT rebooting

From the package "parted" you can use the command "partprobe" to re-read the partition table. I really hate rebooting, and that's what Iloved to hear about AHCI motherboards, that they allow hotswap so you don't have to reboot. But that's only as good as the OS, if the OS does not reload the partition table you won't be able to do anything with that new drive you attached without rebooting. Yes, even without re-reading the partiton table Linux will........

Linux EXT3 16GB-17GB maximum filesize issue solved/how to fix

I have no idea why but mkfs.ext3 defaults to a patheticlly small blocksize of 1024 bytes/1KB (kilobyte). That means the maximum filesize is ONLY 16GB! With 2KB/2048 bytes you get a 256 GB maximum filesize, and with 4KB/4096 bytes you get 2TB! I finally noticed/paid attention to this after realizing that with rsync and scp that no file larger than 17GB could be transferred. I then realized it must be a file size limit on the partition. Here is what tune2fs tol........

Asterisk FreeBSD compile problems

Asterisk FreeBSD compile problemsI couldn't get it to compile without using the following options at compile time: [b:b7d672ee28] make install WITHOUT_ZAPTEL=YES WITHOUT_MYSQL=YES WITHOUT_FAX=YES WITHOUT_ODBC=YES WITHOUT_H323=YES[/b:b7d672ee28]Some problems you might have with copying over your Linux config files to FreeBSD is different paths. [b:f044931f41]For example the etc path for Asterisk on BSD will now be:[/b:f044931f41] [qu........

Heredoc warnings

Heredoc warningsExample $somevariable = ........

MySQL Server 3.23 won't start after switching from 4.1

MySQL Server 3.23 won't start after switching from 4.1I was using a 4.1 alpha version of mysql-server and some how version 3.23 of the client and 4.1 of the client were also both installed! So I forced uninstalled everything because after trying and trying even though MySQL server was using the short 16byte password authentication I got some other errors. After trying with the ports and having it fail because I had existing database data I force installe........

Any experience with Princo 56x?

Any experience with Princo 56x?Hey guys, I was at the Richmond Night Market and saw a lot of cheap CDR media. I'm wondering if anyone has burned a lot of Princo media, especially 56x. Is it good? Have you done a lot of scans for C2 errors? Do you have any old Princo's that play back properly? I'm wondering if they're good so maybe I'll have to find out myself :)........

auth/auth_util.c:make_server_info_sam(840) User nobody in passdb, but getpwnam() fails! - SAMBA/SMB Error How To Fix

auth/auth_util.c:make_server_info_sam(840) User nobody in passdb, but getpwnam() fails! I never found the solution to this in the web, as usual so Ithought I'd post the fix. In plain English smbd is telling us that the user "nobody" does not exist in /etc/passwd. You can simply add this to your /etc/passwd file like so: nobody:x:65534:65534:nobody:/nonexistent:/sbin/nologin Now SAMBA/smbd should........

Enable/Disable PHP Warnings/Logs and Errors from .htaccess with Apache

Put what you see below into your .htaccessand it will enable errors and notices. (change on to off and 1 to 0 to disable though) php_flag display_startup_errors on php_flag display_errors on php_flag html_errors on Now you'll be able to see errors and notices but this should really only be used for debugging purposes and only temporarily as it can be a security issue since errors can reveal information you wouldn't want hacker........

GRUB "Error 2: Bad file or directory type" 0.97 won

You can see the problem below, GRUB recognizes my hard drive and sees the partitions but cannot access them. This is from the GRUB boot disc I'm using. What happened is that I had some power issues causing this system's power to be interrupted several times and basically an on/off on/off situation. The system won't boot, I just get a flashing cursor and no message or error from GRUB. Obviously the problem is that my MBR seems corrupt or some other issue. My........

Tyan S2735-8M Maximum Hard Drive Limit/Not Working/Doesn't work with 1TB 1000GB hard drives

Inever saved any of the logs, but basically no matter what OS (Linux)I used, I could not get my 1000GB hard drive to work (Seagate SATA). The BIOS recognizes the drive and fdisk -l shows the hard drive as it should. The tricky thing is that different OS's will give you different results, but don't be fooled. You can't use these larger drives for long. Iwas getting all kinds of seek/IOerrors and also messages that the port could not be read.........

sudo: Error dropping capabilities, aborting in Linux Centos 5.3

For some reason Ikeep getting this error when trying to run a sudo command eg: sudo -u someuser somecommand sudo: Error dropping capabilities, aborting My version of sudo is:sudo-1.6.9p17-3.el5_3.1 and I've heard that version 1.7 fixes everything. The only thing is yum does not think sudo has any update. Iguess the new version has not been committed to the RPM repository yet. This is really a huge and ann........

iPhone/iTunes sync error "0xE8008001"

This happened during a sync of my iPhone while installing some apps. This usually happens to non-jailbroken iPhones who are trying to install non-Apple approved software OR jailbroken phones who haven't done the "Sync update". How to fix this error and get the Sync Update Open Cydia - Manage - Sources - Edit Add this source: http://cydia.hackulo.us Then under the section "Hackulo.us" install "Ap........

Using a Mac OSX DMG Image in Windows and Converting to Standard ISO Format use dmg2iso

The dmg format is silly and annoying to work with, why couldn't Apple stick with the .iso standard? Anyway, there's an excellent Linux and Windows based tool to convert it back to a normal .iso Image called dmg2iso I'll only cover theLinux version although the Windows pre-built binary works the same way. Download dmg2iso here for free (from the author's website) It's just silly and doesn't make sense that Ubuntu doe........