• How To Force Flash an AMD Instinct GPU To Another Model Using Debian Ubuntu Mint Linux


    Be careful with this and make sure you know what you're doing. In this example we took an Old AMD Instinct Mi25 GPU and flashed to WX9100, because both cards are essentially the same hardware (gfx900) but the WX9100 firmware will enable the miniDP port and also higher power and performance (Mi25 is capped at 110W vs WX9100 170W and of course makes use of the display). Most guides on the internet for some reason have people using a physical ROMprogrammer, which works but is........

  • kdenlive audio blips pops cracks artifacts solution fix


    This usually happens because kdenlive is not smart enough to deal with multiple types of files, especially different frequency. If you take a 44.1khz audio track and then add a 48khz track, you will definitely get the pops and clicks. Use a tool like audacity or similar to do two things, flatten the audio tracks to mono and at least make sure both tracks have the same frequency. I recommend changing both to 44.1khz. After Idid this and reimported the trac........

  • Alibaba Aliyun how to reset password solution 'Setup does not meet the requirements, please resetting'


    Yes, it's real and it is not easy to reset the password. You will find conflicting information on the password requirements even with the same page it implies you need 2 examples of uppercase, lowercase, punctuation/symbols and numbers but that is false. It is compounded worse that it never gives you the correct information below unless you are in private mode in your browser. Here is what you really need for a working and insecure Alibaba password:........

  • ffmpeg burning subtitles in non-English errors [Parsed_subtitles_0 @ 0x561d3a0b3b80] Glyph 0x6709 not found, selecting one more font for (Sans, 700, 0)


    Getting errors like this when burning non-English subtitles? [Parsed_subtitles_0 @ 0x561d3a0b3b80] Glyph 0x6709 not found, selecting one more font for (Sans, 700, 0) [Parsed_subtitles_0 @ 0x561d3a0b3b80] Glyph 0x4E9B not found, selecting one more font for (Sans, 700, 0) [Parsed_subtitles_0 @ 0x561d3a0b3b80] Glyph 0x4EBA not found, selecting one more font for (Sans, 700, 0) [Parsed_subtitles_0 @ 0x561d3a0b3b80] Glyph 0x505A not found, selecting one more fon........

  • How to Spider the web archive.org to recover your old website/webpage


    There are problably a million blog posts telling you how to do it, but none of those guides worked for me. Things can often be different sites and other "unknowns", so there is no guarantee this works for you or for every site. First we'll use curl to search for all the relevant files for the domain and based on the snapshot/timestamp in bold below. curl -s "https://web.archive.org/cdx/search/cdx?url=yourdomain.com/*&to=2........

  • How to install ZFS on Linux Ubuntu Debian Mint


    First of all make sure contrib is enabled in /etct/apt/sources.list, if not follow this guide to add "non-free contrib" to the repos. https://realtechtalk.com/How_to_Add_Contrib_Packages_to_DebianLinuxMint_by_editing_etcaptsourceslist-2636-articles ZFS is popular because it provides actual error checking and correction to a level that is be........

  • ksoftirqd/3 Linux high cpu usage solution


    This is often related to your network traffic and that most of the time Ifind the kernel just uses a single core to send or receive via your NIC. This can be adjusted like this so that multiple cores are used to send and receive data via your NIC (eth0). multicore eth0 RX #enable multicore echo f > /sys/class/net/eth0/queues/rx-0/rps_cpus # enable flow and entries cou........

  • Flash LSI MegaRAID 2208 to IT mode in Linux Mint/Debian/Ubuntu


    03:00.0 RAID bus controller: Broadcom / LSI MegaRAID SAS 2208 [Thunderbolt] (rev 05) This is risky but if you have an extra RAID/SAS card to replace it then you can try this to get IT mode. https://docs.broadcom.com/docs-and-downloads/host-bus-adapters/host-bus-adapters-common-files/sas_sata_6g_p14/9207_8e_Package_P14_IT_Firmware_BIOS_for_MSDOS_Windows.zip https://docs.broadcom.com/docs/12350477 Get the sas2flash for Linux: https://doc........

  • LSI MegaRAID in Linux Ubuntu / Centos Tutorial Setup Guide megacli


    Usually when I come across a system like this, Ijust flash the firmware to an IT mode so we get just an AHCI system with JBOD, but sometimes it is not practical for remote systems or if we fear that flashing is too risky if something goes wrong. In this case, we unfortunately have to use LSI/Broadcom proprietary CLI tools (megacli) to even make the drives visible. Step 1 - Download MegaCLI The official broadcom packages lack .deb packages and only have .rpm for........

  • Cisco CME and C7200 Router Testing and Learning Environment on Ubuntu 20+ Setup Tutorial Guide


    Since newer versions of Ubuntu like 20, you will find there is no longer dynagen and that the dynamips provided is faulty and will segfault each time: Cisco Router Simulation Platform (version 0.2.14-amd64/Linux stable) Copyright (c) 2005-2011 Christophe Fillot. Build date: Apr 3 2018 12:20:29 Local UUID: 3c1c0b7f-2fab-4fda-b40b-74841d1bcfe0 Instance ID set to 1. netio_tap_create: unable to open TAP device tap1 (No such fi........

  • CDN Cloudflare how to set and preserve the real IP of the client without modifying application code on Apache


    Your frontend CDN (eg. Cloudflare or even your own load balancer/proxy) must be sending the X-Forwarded-For and you must be running Apache on the backend. This solves the problem where your logs and services will only see the proxy/CDN IP and not the real client IP. modremoteip is the most modern and current working solution Step 1.) Enable remoteip a2enmod remoteip Step 2.) Edit/Enable the correct config Edit t........

  • Dell Server Workstation iDRAC Dead after Firmware Update Solution R720, R320, R730


    This is certainly a poor design, as you can read many seasoned admins who have updated their iDRAC only to have it killed. One possible cause is not by doing all the incremental updates, doing updates from an old iDRAC to one many revisions newer is a sure way to kill things, but even then there is no guarantee based on the amount of failures. List of threads of people's dead iDRAC's:........

  • isc-dhcp-server dhcpd how to get longer lease


    You can do a static lease that is tied to the MAC address but what a lot of users prefer is that they come into the office or lab the next day and that their device gets assigned the same IP address (if possible). As we can see in the dhcpd logs that there is threshold that is defaulted as we'll show later. Whatever the threshold is set at, if the lease is younger than the threshold, it will keep the same lease. In other words, if the device goes to sleep or is powered off........

  • nvidia cannot resume from sleep Comm: nvidia-sleep.sh Tainted: Linux Ubuntu Mint Debian


    This seems to happen in many different drivers but it happened more often in newer versions such as 530 vs 525. Then nvidia-modeset goes to 100% There are many reports of this appearing since driver 4.70 and I can confirm I've seen this in various machines. https://forums.de........

  • Save money on bandwidth by disabling reflective rpc queries in Linux CentOS RHEL Ubuntu Debian


    Even today we see a lot of servers that have different services and ports open for rpc and this creates not only potential inward vulnerabilities but perhaps more common, the abuse of your network resources in reflective rpc queries. To stop this problem, you should disable and remove all services relating to rpc or at least block all relevant ports for the service. Surprisingly, there are still some providers and OS installs in Linux that install these services and leave them........

  • Docker Swarm vs Kubernetes Comparison Guide


    A lot of companies are unsure which solution to choose and many may not be aware of Docker Swarm as an alternative to Kubernetes. One thing that many Sysadmins find is that Docker Swarm is simply easier, quicker to setup and maintain by far than Kubernetes.........

  • When is it time to leave your VPS/VDS Cloud Hosting Provider?


    When Is It Time to Leave Your VPS, VDS, and Dedicated Server Provider? Choosing the right hosting solution—be it Virtu........

  • apache2 httpd apache server will not start [pid 22449:tid 139972160445760] AH00052: child pid 23248 exit signal Aborted (6) solution Mint Debian Ubuntu Redhat


    If you get this error, it is often because you have configured Apache with modules that weren't actually installed. Eg. you try to load the PHPmodule but didn't actually install the apache2 php module, so the server can't start. In general, this error can often be caused by issues with problematic modules and/or Apache being configured for modules that have not actually be installed (eg. libapache2-mod-php) is missing. The above results in this less than obv........

  • How To Setup Python3 in Ubuntu Docker Image for AI Deep Learning


    The issue is that Docker images are stripped down, so many tools and even python3 is missing, so you'll have to build or update the actual image yourself. I assume you have started an image with something like this and that you have the Nvidia Toolkit installed (assuming you are using GPUs). If you're not using nvidia just remove --runtime=nvidia --gpus all. docker run -it --runtime=nvidia --gpus all ubuntu bash These works for most images li........

  • Linux How To Upgrade To The Latest Kernel Debian Mint Ubuntu


    How to check what kernel version you have/currently running? uname -rm 5.4.0-91-generic x86_64 The above shows us that we are running 5.4.0-91-generic on the x86_64 architecture. The safest way is to stick with the same flavor eg if you're on generic, and say on kernel 5.4.0 then it makes sense to follow what is below. However, if you are migrating or dual booting between newer hardware (eg. you got a........

  • Linux Ubuntu Mint Gnome keyboard Typing not working in certain application or window solution


    This is a weird issue in Mint Ubuntu gnome that I've only seen on one system. It may happen in your terminal or your browser but one program will just refuse to allow input from the keyboard. I am not sure if it's some weird fluke on a strange keyboard by perhaps accidentally hitting a weird key combination. In some windows the keyboard gets weird and only / and Esc seem to work. / brings up quick find and sometimes Esc will close it........

  • Linux How to Check Which NIC is Onboard eth0 or eth1 Ubuntu Centos Debian Mint


    So say you happen to have 2 NICs of the exact same chipset, they will generally show up as the same name, with possibly a different revision in lspci. Normally this is not an issue if you have a server with 4 NICs, generally the eth0 to eth3 appears from left to the right (or right to left on some vendors) so it doesn't take much figuring out. Generally if you have different chipsets for different NICs, it should be easy to know which one is eth0 or the first NIC in the OS.........

  • Dell PowerEdge Server iDRAC Remote KVM/IP Default Username, Password Reset and Login Information Solution


    Are you new to the company, datacenter or a third party who is responsible for deploying a fleet of servers from scratch. The first step is to normally login to the KVM so you can perhaps manually reinstall, PXE boot the Cloud Image or reimage/reinstall an OS but you need access to the KVM/IP or what Dell calls iDRAC. It's common that you may have forgotten this information or that another employee or colleague has changed the info and did not tell you, that they have left the........

  • Thunderbird Attachment Download Error Corrupt Wrong filesize of 29 or 27 bytes Solution


    This is an ongoing issue even with the latest Thunderbird 102.x where attachments downloaded via IMAP just won't save or will be corrupt which is a huge interruption to workflow or if you come back later to find out the file you thought you saved is invalid/corrupt and you have perhaps deleted the e-mail. How to solve the Thunderbird filesize attachment issue? 1. Click on "Settings". then go to "General". 2. Scroll to the bottom to find "Conf........

  • Cisco Switch / Router How To Restore Factory Default Settings


    1.) Make sure your conf register is 0x2102 Do show version and at the very end of the output you will see the Configuration register. show version Configuration register is 0x2102 If the config register is not 0x2102 then enter this command: r1#configure terminal r1(config)#config-register 0x2102 r1(config)#end 2.) Let's Erase the NVRAM/flash........

  • Cisco 2900 3900 Router Password Reset How To Reset Enable Password


    It is a bit different and annoying here for these types of routers/models as you need to physically remove the CF (Compact Flash) and only then, will it enter ROMMON mode (Ctrl + Pause remotely over the console will not do it for us). This means you cannot do this remotely, or at least not without the help of a remote/physical helper. Step 1.) Power off, router and remove CF Disk Slot#2 Go to the router and remove the slot#2 cover uses your hand or it may help to use a........

  • i915 nouveau Nvidia GPU not starting lightdm Xorg failing solution for Could not determine valid watermarks for inherited state


    It may appear to be an Xorg or lightdm/gdm/mdm error but in reality for many users with this issue, it's a driver conflict and issue. I had a system that had two GPUs, an Intel and Nvidia GPU. The only thing that got it working was to remove the nouveau driver and blacklist it so it never came back, then the Intel GPU works fine without these issues. Solution sudo rmmod nouveau add nouveau/other driver to blacklist edit th........

  • How To Tell Which Repository a Package Comes From Debian Mint Ubuntu


    Just use apt-cache policy to find the repo of a package: apt-cache policy lxd lxd: Installed: 3.0.3-0ubuntu1~18.04.2 Candidate: 3.0.3-0ubuntu1~18.04.2 Version table: *** 3.0.3-0ubuntu1~18.04.2 500 500 http://archive.ubuntu.com/ubuntu bionic-updates/main amd64 Packages &nb........

  • Debian Ubuntu Mint DHCP dhclient quits and how to make it persistent if first attempt to get DHCP lease fails


    Debian based OS's have a similar issue as the behavior in RHEL/CentOS dhclient, which is that if you have an interface that relies on DHCP, if the first attempt fails, it will quit and stop. This is a problem especially if you are using your Linux as a router or something else mission critical, but where the internet for some reason may have been down or the DHCP server it gets a lease from broken. The expected behavior you would hope is that when things are back online that the........

  • How To Do Linux Network Bonding Teaming in Mint Debian Ubuntu


    Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........

  • How To Shrink Dynamically Allocated VM QEMU KVM VMware Disk Image File


    Let's say you have a VM file that uses 200G of dynamic space, but really only has 40G in usage. If you add fles and delete, at some point the file will be larger than the current space you are using. Take this image which shows is using 71G of space on the host: The actual space being used inside the image is about 43G as we can see:........

  • How To Enable Linux Swapfile Instead of Partition Ubuntu Mint Debian Centos


    This may be necessary if you have a VM or if for some reason you just want to be more efficient with your space and have the flexibility of changing your swap space at will. What we mean is the ability to use a "swap file" or similar to the Windows "pagefile" that normally resides on the root or c: partition of Windows. Here's all you have to do and then you to can have a single partiton with everything, including the swap file on the root partition if you........

  • Docker Tutorial HowTo Install Docker, Use and Create Docker Container Images Clustering Swarm Mode Monitoring Service Hosting Provider


    The Best Docker Tutorial for Beginners We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........

  • tag#4 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE tag#4 Sense Key : Illegal Request [current] res 40/00:b4:98:02:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) solution


    You might assume you have a bad drive or the SATA interface/cable is bad, or the power supply is bad/weak to the drive. These are all possible issues, but definitely check your SATA cable for "twisting". It is a big issue because until the error stops or times out, your system will not boot (in my case this was the case even though the drive with the issue was not part of the OS or booting process at all). If you run an open rig that you move around often that ha........

  • iptables how to delete rules based on source or destination ip port or just the rule itself


    Let's say we have an IP that is dropped by iptables 192.168.20.2 service iptables status|grep 192.168.20.2 184 DROP all -- 192.168.20.2 0.0.0.0/0 You can use iptables itself like this to list the line numbers: iptables -L --line-numbers Two Ways To Delete The iptables Rule........

  • Ubuntu Linux Mint - Volume Control Stopped Working


    Volume control will often stop working, if your sound server (normally pulseaudio) dies or restarts whether by itself or by you. The reason pulseaudio may need to be restarted is due to some sort of crash or other issue that prevents sound from working (normally restarting or doing a killall pulseaudio fixes things). However, you will normally find at least in OS's like Ubuntu/Mint 16/18+ that you cannot control the volume whether adjusting the level, changing input/outputs and........

  • Linux Ubuntu Debian Centos Mint - How To Check if Intel VT-x or AMD-V Hardware Virtualization is Enabled?


    From the terminal do this: cat /proc/cpuinfo|grep -E "svm|vmx" You should get output like this(svm = AMD-v and vmx=Intel-VTx): flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc cpuid aperfmperf pni pclmulqd........

  • Cisco Switch Howto Reset Password


    This was done on a 2900 but applies to all the switches of the same era. Step 1 - Power Cycle and enter recovery mode If you have physical access you can power cycle and hold the mode button down for 15 seconds. After that the SYS light will flash on the switch and you will see the following screenshot. If you don't have physical access (eg. it is a datacenter swich over console only) then power cycle and hit "Ctrl+Pause/B........

  • Juniper JunOS Command Overview and Howtos Switch, Router, Firewall Tutorial Guide


    Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........

  • QEMU KVM Keyboard Problems Not Working Right Repeating Characters, Ctrl+C Copy and Paste not working right when using PS2 mouse in guests Solution


    It seems that QEMU/KVM's default PS2 mouse and keyboard doesn't work right in most cases. I have especially observed issues using Ctrl+C and Ctrl+V and in Linux you may see repeated key presses in the terminal and you will wonder why you copied something and it's not in the clipboard when you try to paste. The way to temporarily fix it is to press the key that is repeating once(works in Linux but not really in Windows). Sometimes when moving your mouse it will also s........

  • Linux how to compile binary with static sharedobjects embedded instead of dynamic to use on multi-distributions and avoid glibc compatiblity issues


    One simple flag to configure will create a makefile that statically links all the shared objects and embeds them instead the binary execute. This means as long as you have the same architecture that things should run. Eg. if you have an old version of Debian with a different version of glibc, then this will solve that problem. ./configure LDFLAGS="-static" To test that it is really statically linked run ldd: ldd src/wget........

  • Microsoft Teams Linux - Calendar Doesn't Work Missed Meetings!


    Teams for Linux is horribly broken, especially because the calendar doesn't show any meetings so unless you are in the right Team and Channel at the right time, you cannot join your meeting or know there is one. As you can see there is an orange bar to represent the meeting but you cannot click it or it makes a new meeting. For some reason this bug is only present in the Linux app but not in the Android App or from the web calendar. This is a horrible design flaw that ca........

  • How To Replace Audio Track of Video using ffmpeg


    A very common use case is that you don't want to waste time using a video editor that requires you to open it up and manually import the video clip and audio clip, then manually delete the old audio track and import the video and new audio. That's too much work and time since we don't want to go through the hassle. ffmpeg is our solution, all we have to do is specify 3 variables and we're done! -i Windows2019-Server-Noaudio.mp4 is our in........

  • apcupsd how to setup and monitor APC UPS units


    It really seems limited in that it can mainly give you the things you would see on the physical unit such as load etc.. wget https://downloads.sourceforge.net/project/apcupsd/apcupsd%20-%20Stable/3.14.14/apcupsd-3.14.14.tar.gz?r=https%3A%2F%2Fsourceforge.net%2Fprojects%2Fapcupsd%2Ffiles%2Flatest%2Fdownload&ts=1598115866 tar -zxvf apcupsd-3.14.14.tar.gz cd apcupsd-3.14.14 [root@somebox apcupsd-3.14.14]# ./conf........

  • CentOS 6 impossible to compile a newer libguestfs


    yum -y install gcc make gperf genisoimage flex bison ncurses ncurses-devel pcre-devel augeas-devel augeas readline-devel checking for cpio... cpio checking for gperf... no configure: error: gperf must be installed configure: error: Package requirements (augeas >= 1.2.0) were not met: Requested 'augeas >= 1.2.0' but version of augeas is 1.0.0 yum remove augeas augeas-libs augeas-devel wget http://downl........

  • How To Get Started on Ubuntu with gpt-2 OpenAI Text Prediction


    apt install software-properties-common add-apt-repository ppa:deadsnakes/ppa apt update apt install python3-pip apt install python3.7 curl gnupg python3.7-dev git ln -s /usr/bin/python3.7 /usr/bin/python3 pip3 install numpy keras_preprocessing curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add - echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........

  • Linux Debian Ubuntu How To Install PEPPER Faster and Latest Adobe Flash Player in Firefox


    Just run this apt install command sudo apt install pepperflashplugin-nonfree browser-plugin-freshplayer-pepperflash After this restart your browser and check Adobe's site to verify if your Pepper flash is working and showing at least version 32. https://helpx.adobe.com/flash-player.html As you'll see below it will download the latest version which is currently 32 and this was not possible with the old/crappy deprecated adobe-flash plu........

  • How To Install python 3.4 3.5 and up on Linux with wine - Working Solution


    This is sure simple if you follow the guide but it took a lot of hacking around to make this work on Debian/Ubuntu! Now before you ask why bother running wine and python, the reason is because Python executables are NOT cross-platform. If you run pyinstaller in Linux, that binary will only run on Linux and the same if you do it in Windows. So it is preferable if you have a single environment that you can create Linux and Windows binaries from rather than running 2 separate........

  • Radeon R3 GPU on Debian Crashing


    Occasionally my whole screen locks up and I cannot even swith to the console and I find this in my syslog: *-display description: VGA compatible controller product: Mullins [Radeon R3 Graphics] vendor: Advanced Micro Devices, Inc. [AMD/ATI]  ........

  • MySQL 5.7 on Debian and Ubuntu - How To Reset Root Password


    MySQL on Debian versions is configured differently than the native local MySQL plugin so you will be disappointed when your password on the mysql client fails by default. Here is how you reset the MySQL root password the proper and "working way" #first we gracefully stop mysql sudo systemctl stop mysql; #then we forcefully kill any mysqld process just in case sudo killall -9 mysqld mysqld_safe;........

  • CentOS 8 RHEL 8 Alma Linux Rocky Linux how to restart the network!


    Yes you have that right, the network service in RHEL8 / CentOS 8 / Rocky Linux / Alma Linux no longer exists. So there is no more systemctl restart network You can restart NetworkManager but it doesn't have the same effect or ifup/ifdown on all interfaces. Generally if NetworkManager is installed you will want to restart it or it won't apply the settings from ifcfg. systemctl restart NetworkManager To repl........

  • mpv / mplayer with Radeon / AMD GPU Video Card Driver enable VDPAU GPU Accelerated Video Decoding


    The easiest way to know if your videos are playing with GPU acceleration are to watch the process of xplayer, mpv or whatever you are playing. The CPU usage should be no more than 10% for that process/program if it is using acceleration. Let's manually play with vdpau to make sure it works before we make it permanent: First make sure you have libvdpau installed: sudo apt install vdpau-driver-all If yo........

  • MariaDB / MySQL Reset Root Forgotten Password on Linux


    mysql reset root password. Oops I can't remember my MySQL root password! [root@centos7test etc]# mysql -u root -p Enter password: ERROR 1045 (28000): Access denied for user 'root'@'localhost' (using password: YES) Stop logger if running/existing: Check if logger is running for mysqld, if so we have to kill it, otherwise when we kill mariadb it may ju........

  • MySQL Bash Query to pipe input directly without using heredoc trick


    Most of us know the heredoc method but what if you need a basic query done repeatedly and manually while working from bash? It is a pain to manually type mysql and login each time. With this command below you can semi-automate those queries: echo "use somedb; select * from auctions" | mysql -u root --password="yourpassword" Just modify the above to suit your needs and you can add more queries by adding a sem........

  • Linux tftp listens on all interfaces and IPs by DEFAULT Security Risk Hole Solution


    Just edit your tftp file for xinetd like this: *Change the IPto be the IPof the interface you want to listen on. To test if your tftp is available on a certain IP range use nc -u yourip 69 to see if you can still connect (/var/log/messages or /var/log/syslog) should show the connection if it is open. Oct 13 23:20:34 01 xinetd[26631]: Started working: 1 available servic........

  • ImageMagick Converted PDF to JPEG some files have a black background solution


    Use these flags: convert -alpha flatten -alpha remove "output.pdf" ljll.jpg And even the pesky black backgrounds should be gone after converting to jpg........

  • Cisco IP Phone How To Reset To Factory Settings Instructions CP 9971, 8800, 8900, 8845, 8851, 8841, 8831, 7961, 7960, 7945, 7942, 7941, 7940.


    This would be crucial especially if the phone is hardened, not being able to reset or change settings could prevent a phone registering in a new environment or even when migrating from office to office. This applies even if you are trying to migrate the phone to another platform such as Asterisk/FreePBX etc... This guide applies to nearly all of the Cisco IP phones that you would use in CME or CUCM from several years ago including models: 9900, 9971, 8800, 8900, 8845, 8851, 8841........

  • Cisco Unified Communications Manager / CUCM IP 8.6,10,12 Install Error Solution


    Install Errors on Version 12: This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5 on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error. *Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install. What really causes this even though you successfully install........

  • Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM


    The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........

  • Cisco Switch Reset To Factory Defaults


    This works on the 2000 and 3000 series generally. *The easy way is to just hold the mode button for 10+ seconds. The full/proper way is below: 1.) Either power on the unit and hold the "mode" button or hold the "mode" button until you see the below: 00:04:08: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram 00:04:08: %EXPRESS_SETUP-6-CONFIG_IS_RESET: The configur........

  • How To Boot Cisco CUCM UCSInstall 8.6, 10, 11 and 12 on KVM/Proxmox


    The key thing is that you must use a "machine"id of "pc-1.3" or it will say your hardware is not supported. Additionally you MUST use a virtio disk or you will get a ks_pre.sh error as soon as the install starts (a look at logs will show it can't find a disk). This is funny because even though the OS finds the disk and an fdisk -l shows it, it looks like the script looks for a /dev/vda device (virtio) and nothing else, so if you didn't use Virtio as you........

  • sudoers file in /etc warning about comments/includes!


    If you see this in /etc/sudoers it is NOT a comment but an include. #includedir /etc/sudoers.d For example in Linux mint sudoers.d contains the following files: casper mintupdate README casper for example contains the following sudoers line: mint ALL=(ALL) NOPASSWD: ALL So if you are messing ar........

  • Proxmox Breaks Storage/LVM Backing If Killing QEMU-IMG


    I tried to stop a qemu-img copy or clone and it broke everything. It was fine to "stop" it from the GUI but a process still persisted so I killed the relevant qemu-img and the kernel went crazy. It also may not have helped that I tried to lvremove a different volume (an unused disk). But either way it breaks LVM (you cannot even run lvdisplay) so a reboot is necessary. Jan 17 06:45:21 testserver kernel: [ 5680.439337] systemd-udevd D 0&nbs........

  • QEMU / KVM How To Manually Create Basic Virtual Machine VM


    1.) Create Image using qemu-img qemu-img create -f qcow2 skype.img 40G 2.) Start VM using flags -m = memory in MB -drive file=yourimagefile.img -cdrom /path/to/the.iso qemu-system-x86_64 -m 4096 -drive file=skype.img -cdrom ~/Downloads/SfB-E-9319.0-enUS.ISO Enable Bridged Networking........

  • Linux use growisofs to burn a larger file on a BD-R / Bluray Disc


    growisofs -Z /dev/sr0 critical.tar.gz.gpg Executing 'genisoimage critical.tar.gz.gpg | builtin_dd of=/dev/sr0 obs=32k seek=0' I: -input-charset not specified, using utf-8 (detected in locale settings) File critical.tar.gz.gpg is larger than 4GiB-1. -allow-limited-size was not specified. There is no way do represent this file size. Aborting. :-( write failed: Input/output error #remember to us........

  • Linux partprobe/partx cannot access last and 4th partition


    On a test machine Iwas never able to access to a newly created 4th partiton. As we can see there are dev devices for everything but the 4th partition. The normal "partprobe" or "kpartx" or kernel being told to rescan the block device didn't help (only a reboot did). fdisk -l /dev/sda Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units........

  • Linux named / bind how to dump, view and clear the cache!


    Do you hate it when your ISPhas old cached records because of a high TTLon the DNS record of the relevant domain? In plain English this means you often can't connect to a site or service because your ISP's DNS servers haven't gotten word of the new IP address (probably because they haven't checked). There are also some that are notorious for ignoring TTL and not updating records for days! But if you are lucky and smart enough to have your own Linux based DNS se........

  • Why SMART is not smart at all and doesn't properly predict disk errors that cause a kernel panic or crash


    Before getting into the output here is my typical experience with SMART, there is what I call a "bad disk" with pending and uncorrectable sectors that cannot be reallocated. It has caused a kernel panic and system crash repeatedly as we can see from the logs. But SMART says it has "PASSED" its self assessment. SMART is still useful to me but it is more about looking at Current_Pending_Sector. Any time I have had anything but 0 for that attribute it........

  • systemd management using systemctl and journalctl to check systemd logs


    systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system. The key commands or arguments you will use with systemctl are the following: Unit Commands: list-units [PATTERN...] List loaded units &nbs........

  • css how to format code in the code tag


    code { background: #f4f4f4; border: 1px solid #ddd; border-left: 3px solid #f36d33; color: #666; page-break-inside: avoid; font-family: monospace; font-size: 15px; line-height: 1.6; margin-bottom: 1.6em; max-width: 100%; &nb........

  • HP DL385 G7 Linux BIOS Update Flash


    wget https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe --2018-08-16 05:11:16-- https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe Resolving downloads.linux.hpe.com (downloads.linux.hpe.com)... 15.249.152.85 Connecting to downloads.linux.hpe.com (downloads.linux.hpe.com)|15.249.152.85|:443... connected. HTTP request sent, awaiting response... 200 OK Length: 1525561 (1.5........

  • Debian Mint Ubuntu compiling xmr-stak


    sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........

  • *** These critical programs are missing or too old: gawk


    checking whether autoconf works... ../configure: line 5377: 7325 Segmentation fault $AUTOCONF $ACFLAGS configure.in > /dev/null 2>&1 no configure: error: *** These critical programs are missing or too old: gawk *** Check the INSTALL file for required versions. ........

  • wodim / cdrecord error cannot burn DVD or BDR .iso Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error


    dvd+rw-mediainfo /dev/sr0 INQUIRY: [ASUS ][BW-16D1HT ][3.00] GET [CURRENT] CONFIGURATION: Mounted Media: 11h, DVD-R Sequential Media ID: RITEKF1&n........

  • VirtualBox Nested Virtual Machine Containers with KVM Not Working no SVM or VMX module in the guest


    I can't get vmx cpu extensions to show up in Virtualbox guests despite enabling nested paging and enable vmx in virtualbox guest but this doesn't help that you check VT-X or the AMD Virtualization SVM it enables it for the guest to use BUT does not pass it through. This means if you check cat /proc/cpuinfo in the guest you will see the CPUdoesn't support virtualization. It looks like VirtualBox still hasn't implemented this! But there is good news I&n........

  • VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI


    #mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........

  • Linux Mint Black Screen after boot no graphics solution


    This is not the normal "black screen"issue and I was shocked to eventually find out why. The normal advice of reconfiguring Xorg didn't work. Even booting into "Recovery Mode" did not help. Here is the short end of the stick that fixed it: sudo apt-get install mdm mate-desktop-environment Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled. This must be whe........

  • SMF Forums / Simple Machines Forums Not Displaying Images Theme or Styles Properly using 127.0.0.1


    This is one thing that has me wondering about SMF. It is apparently a known issue but in the latest version and new install nothing looked right because it was using http://127.0.0.1 to find everything! How on earth would it ever do this or think it is normal? Excerpt of crazy html code it produces that causes the issue: ........

  • Apache htaccess Custom ErrorDocument not working properly for root home page 403 Error Issue and Solution


    So I have a domain "testdomain.com". Inside test domain.com's root is the following .htaccess: Options +FollowSymLinks -Indexes ErrorDocument 403 /launch/index.html Order Deny,Allow Deny From All Allow From 192.168.1.2 When you visit anything other than root things work fine. Eg. if you visit http://testdomain.com/somedirfile.html It will show the right error in /launch/........

  • PHP Warning: Cannot load module 'XCache' because conflicting module 'apc' is already loaded in Unknown on line 0


    PHP Warning: Cannot load module 'XCache' because conflicting module 'apc' is already loaded in Unknown on line 0 Solution: yum remove php-pecl-apc-*........

  • Unable to load dynamic library '/usr/lib64/php/modules/module.so' - /usr/lib64/php/modules/module.so: cannot open shared object file: No such file or directory in Unknown on line 0


    Getting this error on Centos 6 with PHP 5.3 when just running "php -v" PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/module.so' - /usr/lib64/php/modules/module.so: cannot open shared object file: No such file or directory in Unknown on line 0 PHP Warning: Cannot load module 'XCache' because conflicting module 'apc' is already loaded in Unknown on line 0 Solution:........

  • mysql how to reset passwords with a few commands


    The commands below will help you reset any mysql user password. use mysql; update user set password=PASSWORD('thenewpass') where User='theusername'; flush privileges; The first line says to use the "mysql" database which contains all the user info. the second update line sets the new password "thenewpass" for the u........

  • possible SYN flooding on ctid 42131, port 80. Sending cookies. - Solution


    The Linux Kernel interpretated a very high volume of real traffic as a DDOS attack so it basically ends up blocking your web server. possible SYN flooding on ctid 42131, port 80. Sending cookies. Simple fix edit sysctl values for max_syn_backlog sysctl -w net.ipv4.tcp_max_syn_backlog=5000 To make them permanent edit /etc/sysctl.conf echo "net.ipv4.tcp_........

  • Install Windows From a Linux TFTP Server instead of using WDS Solution


    yum -y install samba vi /etc/samba/smb.conf https://www.kernel.org/pub/linux/utils/boot/syslinux/syslinux-6.03.zip mkdir syslinux;cd syslinux;unzip syslinux-6.03.zip mkdir -p /tftpboot/libs/ cp bios/com32/modules/linux.c32 /tftpboot/libs/ cp bios/com32/libutil/libutil.c32 /tftpboot/libs/ cp bios/com32/lib/libcom32.c32 /tftpboot/libs/ #add lib path echo "PATH libs" >> /tftpboot/pxeli........

  • Linux how to view video card make and exact model


    Normally lspci will show you just like this and would suggest they are exactly the same card: 1a:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Ellesmere [Radeon RX 470/480/570/580] (rev e7) 1c:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Ellesmere [Radeon RX 470/480/570/580] (rev e7) lspci -vnn is the answer As we can see one is a Gigabyte and the other is an MSI card. Wha........

  • responsive table without changing much code solution


    So you've got a responsive site with tables but it breaks them so anything not viewable on the screen is now cut off. Here is a simple solution that will allow users to scroll horizontally so they can see the whole table: &........

  • bash Linux how to get first or last letters of a word


    To get the first X letters of a word: It's very simple you can just pipe it to head with -c 1 (gives the first letter and so on) -c2 (2 gives the first 2 letters). echo "dsjfsdlksjdklf;jlsd;kflasdj;kl"|head -c 2 Returns ds To get the last X letters of a word: Now we use tail with -c but it works differently. ........

  • Wine uninstalled broken on Linux Mint


    Solution: Aptitude is very smart and fixed the issues it was because of nvidia cuda and opencl and nothing else suggested or hinted this using apt sudo aptitude install wine The following NEW packages will be installed: ocl-icd-libopencl1{ab} ocl-icd-libopencl1:i386{ab} wine wine1.6 wine1.6-amd64{a} wine1.6-i386:i386{a} The following packages will be REMOVED:........

  • ffmpeg trouble concatenating similar but different files


    When things go wrong your video is basically unplayable or the first video plays fine and then freezes when moving on to the next. Generally if both videos weren't produced with the exact 100% same settings you will have issues. You can try the basic concat but it often won't work right. Solution for me: My example uses 3 videos in total so "n=3" and a=1 to include audio. ffmpeg -threads 12 -i file1.mp4 -........

  • ffmpeg Linux Mint download, compile and install howto


    #if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2 tar -jxvf ffmpeg-3.3.2.tar.bz2 cd ffmpeg-3.3.2/ ./configure --disable-yasm install prefix /usr/local source path ........

  • How to change reserved blocks in Linux partition


    user@box:~$ sudo tune2fs -l /dev/md99 [sudo] password for user: tune2fs 1.42.9 (4-Feb-2014) Filesystem volume name: Last mounted on: /mnt/md50 Filesystem UUID: 976a8655-2619-4587-878c-dab07f7b7652 Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Fi........

  • USB 3.0 External HDD Enclosure Seagate UAS problems - [sdd] tag#1 CDB: Write(16) 8a 00 00 00 00 01 70 04 08 68 00 00 00 08 00 00


    This is a 8TB Seagate external USB 3.0 device apparently newer kernels use a module called "UAS" instead of "USB Storage" which causes issues as a lot of devices are not properly supported in UAS mode by the kernel driver. The solution some say is to disable UAS specifically for your USB device but I'd rather just disable UAS altogether. Solution blacklist UAS: *do not do this it does not work and just causes your USB 3.0........

  • cudaminer freezes Linux Mint taints kernel


    When running cudaminer once it tries to initialize the card the entire screen freezes. The computer itself is still running but the Xorg is done for, you cannot even switch to another console window and must reboot (even an mdm or Xorg restart does not help). At first cudaminer will give you these errors: stratrum_recv_line failed ...retry after 15 seconds GPU #0: Geforce 210 with compute ca........

  • USB Device/MP3 Player not working properly and can't browse the device filesystem? Check the cable twice and again!


    Here is a simple MP3 player and now there's a reason to understand why the supplied cable has some kind of capacitor and is very short. These devices can be VERY finicky and any voltage fluctuation or difference is enough to cause issues. Take for example the error messages from Linux Mint: [804829.895414] usb 1-1: USB disconnect, device number 11 [806961.109030] usb 1-1: new high-speed USB device number 12 using xhci_hcd........

  • Openshot 2.2 is very unstable always crashing in Linux Mint 18.1!


    Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Missing folder chosen by user: Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Removed missing file: MAH02949.MP4 Jun 1 15:45:57 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: ui_util:WARNING Icon theme media-playback-start not found. Will use backup........

  • Track 01: 34 of 1726 MB written (fifo 100%) [buf 99%] 3.6x.Errno: 5 (Input/output error), write_g1 scsi sendcmd: cmd timeout after 1.897 (40) s CDB: 2A 00 00 00 44 A9 00 00 1F 00 resid: 6144 cmd finished after 1.897s timeout 40s write track da


    These errors believe it or not are simply because of not being the root user or running with sudo! However if you didn't know to try as root you'd think there was a problem with your burner or disc Essentially it looks like without root you cannot send the required scsi commands to continue writing. Ithink cdrecord should have built-in tests or safeguards to see if it has the permissions to run the required commands. I guess for more advanced users the idea is simila........

  • Transaction Check Error: file /usr/lib64/php/modules/fileinfo.so conflicts between attempted installs of php-pecl-fileinfo-1.0.4-2.el6.rf.x86_64 and php-common-5.3.3-49.el6.x86_64 solution


    Transaction Check Error: file /usr/lib64/php/modules/fileinfo.so conflicts between attempted installs of php-pecl-fileinfo-1.0.4-2.el6.rf.x86_64 and php-common-5.3.3-49.el6.x86_64 solution you can't install php-pecl-fileinfo it seems to be incompatble with the php5.3 being installed: yum --exclude=php-pecl-fileinfo --skip-broken --disablerepo=epel install php-*........

  • mdadm frozen and doesn't realize array is dead/missing failed due to unplugged drives


    This was a surprising bug but I unplugged all drives for an array md127. At first it was just 1 drive and mdadm seemed to notice this. I unplugged the second drive taking the array offline but mdadm did not realize it was offline and still showed a non-existent disk as being part of it. This created problems trying to unmount it or even to stop this array with mdadm freezing. As for how to fix it I can only think of making sure you are not in a mounted path of........

  • DRBD Split-brain solution


    Uh oh [17925926.174277] block drbd0: Handshake successful: Agreed network protocol version 96 [17925926.174325] block drbd0: conn( WFConnection -> WFReportParams ) [17925926.174342] block drbd0: Starting asender thread (from drbd0_receiver [1682]) [17925926.174432] block drbd0: data-integrity-alg: [17925926.174581] block drbd0: drbd_sync_handshake: [17925926.174586] block drbd0: self 2AAE66AF9252D6DB:2815BF........

  • ERROR 2013 (HY000): Lost connection to MySQL server during query


    The solution is simple but strange, if you copy your /var/lib/mysql directory to another server and think it will work, be sure to check if you have /var/log/mysql and binary log files. If you do, the server will not work and will give you errors like below and crash without the proper log files. UPDATE user SET password=password("newpass") WHERE user='root'; flush privileges; ERROR 2013 (HY000): Lost connection to MySQL server durin........

  • fdisk wq causes hung process


    I created a new partition table on a newly plugged in device and it caused fdisk to hang (even force kill does not work). It also may be a bad drive or some other issue because fdisk -l hangs after the first 2 HDDs (totaly of 8 HDDs on this system): [1232879.903596] INFO: task fdisk:27176 blocked for more than 120 seconds. [1232879.903607] Tainted: P&nbs........

  • Linux How To Recover Partition Table from Kernel and Restore Centos/Debian etc..


    We've all done this at some point, you work on the wrong shell window and this was my first time making this mistake but I deleted a partition table in fdisk, recreated it and saved it with "wq" and even ran partprobe! If you haven't rebooted yet then you can still recover your partition table, otherwise you're in big trouble. Fortunately since it was a live system and in use the kernel still had to use the old table like below:........

  • blocked for more than 120 seconds issues with iowait and timeout on Live Linux distribution while writing to physical disk


    This happened while an mdadm array was syncing, all access from writing a new blank file to opening a small .txt file was very slow: [222117.312078] kjournald starting. Commit interval 5 seconds [222117.685060] EXT3-fs (md0): using internal journal [222117.685096] EXT3-fs (md0): mounted filesystem with ordered data mode [222122.376847] kjournald starting. Commit interval 5 seconds [222122.602825] EXT3-fs (md2): using internal jour........

  • possible SYN flooding on port 80. Sending cookies.


    Errors like this are shown on high usage servers and ports so it is common to see it on http and even imap ports: possible SYN flooding on port 80. Sending cookies. The Linux kernel will even detect flooding on OpenVZ containers: possible SYN flooding on ctid 6000, port 993. Sending cookies. In many cases this is not an issue and is more so simply a result of regular, but high usage traffic.........

  • Openvz kernel: [10186978.064405] TCP: time wait bucket table overflow (CT3)


    kernel: [10186978.064405] TCP: time wait bucket table overflow (CT3) Varying opinions are out there but in general it seems like the most common culprit is a lack of privvmpages, with a modern OpenVZ system the best way is to set privvmpages as equal to what your RAM is and this has resolved the messages on another system. If it's truly a TCP issue you can adjust the following parameters:........

  • Nvidia Linux Card not working due to LSI 9200/SAS2008 IRQ conflict


    At first my BIOS said the card may not work right because there is no more option ROM space. I disabled the Option ROM for both LSI 1068 and 2008 chipsets, Network Boot ROM and most other PCI slots, Serial Port, etc... and the message went away but the card still does not work properly. But it still cannot initialize the card properly(does not work): [ 33.943272] NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:........

  • SAS2008 LSI 9200-E Linux Upgrade Flash Firmware with sas2flash


    Download from here http://www.avagotech.com/products/server-storage/host-bus-adapters/sas-9200-8e#downloads sudo Installer_P20_for_Linux/sas2flash_linux_i686_x86-64_rel/sas2flash -listall LSI Corporation SAS2 Flash Utility Version 20.00.00.00 (2014.09.18) Copyright (c) 2008-2014 LSI Corporation. All rights reserved &nbs........

  • Apache Vhost HowTo Serve Same Content using a different domain and IP


    There are a few ways of doing this and all basically involve using the reverse proxy or "ProxyPass" feature of Apache to accomplish it. 1.) Create a normal vhost and simply symlink the root directory of the site you want to mirror. Eg. originalsite.com and newsite.com /vhosts/originalsite.com/httpdocs You would symlink like this: ln -s /vhosts/originalsite.com/httpdocs vhosts/originalsite.com/........

  • MySQL PHP adding a backslash/escaping apostrophes Solution


    The first thing to diagnose is what is actually in the database (use PHPMyAdmin or CLI). You will of course either find that the backslash is either in the database or not. If the backslash is in the database you probably have magic quotes gpc/runtime on and/or are calling the "addslashes()" function which does this. If you are escaping your data with mysql_real_escape_string() then think again, you probably have magic quotes gpc enabled either in php.ini or........

  • Avocent 8020 KVM Java Icedtea Viewer


    This command in Debian/Ubuntu/Mint will get everything need installed for most Java based KVM viewers: sudo apt install icedtea-netx The following additional packages will be installed: ca-certificates-java icedtea-netx-common openjdk-8-jre openjdk-8-jre-headless It seems every other updated version of Java or Icedtea breaks things and I will save the frustration of Java for another post.........

  • Bing/Microsoft Ads flex.atdmt.com causing problems for ad tracking and site loading


    I was asked to troubleshoot why a site wasn't loaded or responding properly, it turned out they were using some old javascript tracker from Bing/Microsoft that is no longer valid or working. You have to wait forever for it to time out but it really did disrupt the functionality of a very important site: flex.atdmt.com If you have the above code in javascript on your site remove or comment it out.........

  • Virtualbox errors on Ubuntu/Debian/Mint


    The solution was to reinstall the vbox dkms package and do a manual modprobe of the modules it makes. I never sorted out the unable to start due to the USB issue, I did have the guest additions installed but the only way to boot was to change the pointing device from USB to PS2 and then to disable the USB controller (if your pointing device is set as USB, disabling USB will not work because it will re-enable by default when it sees your pointing device is USB, this is w........

  • flypro EEPROM PLCC32 programmer software error "The device ID does not match, whether to continue operating"


    If you get that message it means you have inserted the adapter or device incorrectly. In my case the adapter needed to be at the rear end of the pins and it caused this message. Do not ignore this message as it may appear to work but you will get errors and in reality your chip will not be erased or programmed even if it appears like it is working.........

  • ssh session and port forward or reverse port matching or assocation howto


    Use netstat with the -anpe option. The e option shows the inodes and I do not know if it will always work or if it was by fluke but I was dealing with dozens of SSHsessions and needed to know which session was related to which forward (the PIDs of the SSHand SSHD did not match etc...) Notice the "59560675" and "59560762" those are almost identical, if you find two sets that are nearly identical except for the last 3 digits they may match (in my ca........

  • Dell CS24 NV5/NV7 Gigabyte GA-3CESL-RH Motherboard ROM Chip info


    If you remove the white label on the chip (near the CMOS battery) you will find the following details about it: SST 49LF080A 33-4C-NHE It is the PLCC32 type and can be pried and removed safely (but be very careful) with an eye glass flat head screw driver. If you just have a bad flash you may be able to reprogram your original or just buy another one with the part# above and reprogram it. This is great news for people who have bricked th........

  • HP Procurve Switch 2824 CLI Telnet Experience , Guide and Tutorial


    ------------------------------------- ProCurve J4903A Switch 2824 Software revision I.10.77 Copyright (C) 1991-2009 Hewlett-Packard Co. All Rights Reserved. RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by the Government is subject to restrictions........

  • tar list files


    tar -ztvf flashrom.tar.gz the "z"is for gzip, if it is not gzip remove the z. If it is bzip then use "j" instead of "z" etc..........

  • Dell CS24-NV7 lspci dmidecode info


    0000:00:00.0 RAM memory: NVIDIA Corporation MCP55 Memory Controller (rev a2) 0000:00:01.0 ISA bridge: NVIDIA Corporation MCP55 LPC Bridge (rev a3) 0000:00:01.1 SMBus: NVIDIA Corporation MCP55 SMBus (rev a3) 0000:00:02.0 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a1) 0000:00:02.1 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a2) 0000:00:05.0 IDE interface: NVIDIA Corporation MCP55 SATA Controller (rev a3) 0000:00:05.1 I........

  • Flash slowing down your Firefox browser? Install Flashblock plugin


    Install the "Flashblock" plugin because we all know most unwanted high CPU usage situations come from the browser usually because of a looping Flash ad taking up 100% CPU. The solution is to install the "Flashblock" plugin that doesn't allow any Flash to load and play unless you click on the placeholder.........

  • KVM: unknown exit, hardware reason 0x80000021 kvm_run returned -22 solution


    If the below is happening on KVM (a very weird and scary looking error) it's probably because of Windows. This has happened countless times to me where the bootsector on Windows 7/2008 becomes corrupted easily (even by a crash or shutdown). KVM: unknown exit, hardware reason 0x80000021 kvm_run returned -22 rax 0000000000000010 rbx 0000000000000080 rcx 0000000000000000 rdx 0000000000000080 rsi 000000000025db2a rdi 000000000007db2a rsp 0000000000000200 rbp........

  • firefox android text size inconsistent large and small text size solution


    This is very annoying and also hard for web developers who want to see how things look on Android. You may be fooled into thinking you have an unclosed bracket or incompatible code but this is the "text inflation feature" which I feel should be disabled by default. It works so inconsitently that one block of text will appear small while the other will be huge and is quite annoying. The solution is simple Settings ->Display and &q........

  • CPanel mysql root password location how to find


    It is located in /root/.my.cnf This is truly a horrible idea and a security flaw and on top of that MySQL port 3306 is wide open by default with CPanel.........

  • heatbeat ERROR: NV failure (msgfromsteam): [>>> ] ha_msg_add_nv_depth: line doesn't contain '='


    Apr 17 11:55:47 Cluster01 heartbeat: [1426]: WARN: ha_msg_add_nv_depth: line doesn't contain '=' Apr 17 11:55:47 Cluster01 heartbeat: [1426]: info: >>> Apr 17 11:55:47 Cluster01 heartbeat: [1426]: ERROR: NV failure (msgfromsteam): [>>> ] I have never been able to reproduce the above but it happened on heartbeat-3.04-2 when Itook a node down for testing. One thing Ibelieve caused it was by configuring ha.cf........

  • Howto Convert Xen Image to KVM


    #count=10000 makes an image of 10000MB make sure your image is at least the same as your existing dd if=/dev/zero of=yourimage.img bs=1M count=10000 # losetup -fv newimage.raw # fdisk -cu /dev/loop0 # kpartx -a /dev/loop0 # dd if= of=/dev/mapper/loop0p1 # e2fsck -f /dev/mapper/loop0p1 # resize2fs /dev/mapper/loop0p1 # a lot of guides tell you to edit /etc/fst........

  • Asterisk VOIP Sipura/Linksys PAP2T Calls Not Being Received Solution


    This problem seemed to happen recently but was likely causing issues before where the phone(s) do not ring. Now there are a few reasons why this can happen especially if your adapter has DND mode enabled (disable it). However that wasn't my issue and Ionly figured it out the other day when by fluke if you're on the phone (making a call) then calls will come in. That's when Ifigured out the solution: This likely app........

  • Enable Multiple RDP Sessions on Windows XP, Vista, 7 Howto


    http://deepxw.blogspot.ca/search/label/Universal%20Termsrv.dll%20Patch The above site has the patch that does this essentialy turning a Desktop Windows into a full fledged RDP server.........

  • nf_conntrack: table full, dropping packet solution


    nf_conntrack: table full, dropping packet The above in some cases I've seen is a sign of a DOS attack or can occur if users are using services like torrenting, proxy, VPNetc... Do not take it lightly as the above can knock a server offline if the table becomes full and I've also seen full crashes and kernel panics shortly after. ........

  • yum error installing php solution - exclude php from being installed from third party repos


    Error: Package: php-Monolog-dynamo-1.7.0-1.el6.noarch (epel) Requires: php-aws-sdk Error: php-pecl-zendopcache conflicts with 1:php-eaccelerator-0.9.6.1-1.el6.x86_64 Error: php-xcache conflicts with php-pecl-apc-3.1.9-2.el6.x86_64 Error: php-pecl-zendopcache conflicts with php-pecl-apc-3.1.9-2.el6.x86_64 Error: Package: php-horde-Horde-Vfs-2.1.2-2.el6.noarch (epel) &n........

  • Centos Howto Upgrade to PHP 5.3 from 5.2


    It's not as simple as "yum install" as you can see below and it doesn't stop there. yum install php53 Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * rpmforge: mirror.us.leaseweb.net * extras: centos.mirror.rafal.ca * updates: centos.mirror.nexicom.net * base: centos.mirror.nexicom.net * addons: centos.mirror.nexicom.net Setting up Install Process........

  • Howto edit/rotate Samsung/Android Videos in mencoder solution


    Movie-Aspect is undefined - no prescaling applied. videocodec: libavcodec (720x1280 fourcc=34504d46 [FMP4]) [mpeg4 @ 0x2c91c00] timebase not supported by mpeg 4 standard Could not open codec. FATAL: Cannot initialize video driver. That is the error I would get, I thought it was a codec error something else. By fluke Isaw something about ffmpeg where someone recommended manually telling it to the "fps" and it worked.........

  • What a hdd hard drive and mdadm RAID array failure looks like in Linux


    [3805108.257042] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [3805108.257052] sd 0:0:0:0: [sda] Write Protect is off [3805108.257054] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [3805108.257066] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [3805108.257083] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [3805108.257090] sd 0:0:0:0: [sda] Write Protect is off........

  • Ubuntu/Debian how to update FlashPlayer manually


    Download the latest from Adobe's site and unzip it, enter the directory it creates and type the following: sudo cp libflashlayer.so /usr/lib/adobe-flashplugin/ sudo cp -r usr/* /usr........

  • strange kernel dmesg errors


    Sep 26 16:56:21 box kernel: 00 00 00 00 00 00 00 00 Sep 26 16:56:21 box kernel: [37007.155690] d_alias libdl-2.12.so d_count=9 d_flags=8 Sep 26 16:56:21 box kernel: [37007.155697] 09 00 00 00 08 00 00 00 9f 05 9f 05 00 00 00 00 c0 71 1d 18 04 88 ff ff 00 00 00 00 00 00 00 00 a0 7e 48 00 00 c9 ff ff 78 a9 21 18 04 88 ff ff 3a 7b fa 4e 0d 00 00 00 98 5c 2d 18 04 88 ff ff 18 5c 2d 18 04 88 ff ff 18 5c 2d 18 04 88 ff ff 00 01 10 00 00 00 ad de 00 02 20 00 00 00 ad de f8........

  • Dell FS12-NV7 2U Server Information and Guide


    I've got one of these for testing projects from work at home and got more than I bargained for with the time I've spent on it due to the storage handing/Perc 6/i cards. My particular model came with the following: 2U Rack Mount Server with Rails 2xOpteron 2373 EE (Quad Core, there is a 6-core version that can be found at times) 16GB RAM 2 x 250GB Seagate SATA 2 x Dell Perc 6/i (horrible and a nightmare to work........

  • Dell Perc 6/i SATA benchmarks without battery


    The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results. This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane. Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: N/A De........

  • Dell Perci 6/i Firmware Upgrade Guide Tutorial


    One thing to remember is that you need MegaCli to do the flashing. You also need the correct file,I tried at least 2 different Perc 6 firmwares from Dell that kept getting rejected as corrupt by MegaCli(they were really the wrong version). I have an external PCI-E Dell 6 Perc/I butI chose images from the 'Integrated" on motherboard version as it was allI could find. They are different, and below is my first time finding success.........

  • Dell Perc 6/i cannot downgrade


    I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally. I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN --2013-08-26 12:53:39-- http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN Resolvi........

  • LSI MegaRAID Adventures, Guide and HowTo


    LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........

  • yum update error


    yum update error Traceback (most recent call last): File "/usr/bin/yum", line 29, in ? yummain.user_main(sys.argv[1:], exit_code=True) File "/usr/share/yum-cli/yummain.py", line 229, in user_main errcode = main(args) File "/usr/share/yum-cli/yummain.py", line 145, in main (result, resultmsgs) = base.buildTransaction() &nbs........

  • iptables redirect ports to a different host and port + NAT Masquerade howto/solution


    This is important if you need public access to internal IPs such as at your office and don't want to use a VPN just to SSHinto different servers: Below forwards the port "10001" to the IP192.200.5.53 on port 22 (of course adjust it to your needs). iptables -t nat -A PREROUTING -p tcp --dport 10001 -j DNAT --to-destination 192.200.5.53:22 Remember to enable MASQUERADE on your NAT IPs or they won't be able to talk to the outside world (........

  • WD 20EARX Dead Again


    Another new drive bad from the start: Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........

  • WD 20EARX 2TB Bad within days


    This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad. ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0 ata1.00: irq_stat 0x40000008 ata1.00: failed command: READ FPDMA QUEUED ata1.00: cmd 60/00:00:........

  • mysqldump: Couldn't execute 'show create table `general_log`': SHOW command denied to user 'user'@'localhost' for table 'general_log' (1142) - Solution


    mysqldump: Couldn't execute 'show create table `general_log`': SHOW command denied to user 'user'@'localhost' for table 'general_log' (1142) One of my clients almost found out the hard way, here is an unlikely situation that happened. 1.) Years ago the client had another VPS to which they backed up a BLOG nightly to an .sql file, what they forgot is that the file also contained all databases (they used the --all-databases option but forgot). So imagi........

  • Solution ERROR 1146 (42S02): Table ‘mysql.servers’ doesn’t exist - when running flush privileges


    flush privileges; ERROR 1146 (42S02): Table ‘mysql.servers’ doesn’t exist This happened to me on a system running Centos with the REMI repo and a new version of Mysql 5 (which the official Centos/RHEL does not support on version 5). The solution is just to run this program "mysql_upgrade", after that flush privileges will work. mysql_upgrade........

  • mdadm recover from dead drive


    mdadm --manage /dev/md3 --add /dev/sda1 cat /proc/mdstat Personalities : [raid1] [linear] [multipath] [raid0] [raid6] [raid5] [raid4] [raid10] md0 : inactive sdd2[1] sdd1[2](S) 31270272 blocks md3 : active raid1 sda1[2] sdb1[1] sdc1[3](F) 943730240 blocks [2/1] [_U] [>....................]........

  • Samsung Galaxy Note I717M Canadian Version, Root and Unlock


    I chose this because I heard a lot of stories about scams and that many providers I contacted said they can't unlock the Canadian I717s (one said "my Bell server" is down). This method worked perfectly on my Bell I717M and should work for all I717 in Canada, I was able to insert a foreign SIMcard. This will work abroad too but remember entering CWM mode is different for I717's in other countries (at least theUS). Step 1 - Root + CWM........

  • Bad Hard Drive Slows Down Computer


    Here's a proven example of what a bad hard drive can do, it was technically functioning OKin a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application. The truth is that this failing 1TBHitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..). After swapping it out, tabs change instantly, emails are not lagged, and........

  • Centos 6 RTL8111/8168B r8169 link up and down error solution/fix


    02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) For whatever reason it seems the r8169 driver that ships and has shipped with most Linux distros for years is still flawed and does not work properly on these cards, causing 100mbit connectivity when it should be 1gbit and even worse, causing random network dropouts. The r8169 driver in Linux kernels is simply not meant to be used on th........

  • kvm cannot boot xen guest using lvm


    This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel. I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk. I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one). This is strange but it seems like this Xen PV guest has some sort of hidden or........

  • Thunderbird Caused Nearly 100% CPU usage with Xorg


    I closed program by program untilI found the culprit, it's baffling how the cause was Thunderbird but then again it does use a lot of memory and I have thousands of messages between dozens of mailboxes. But still I don't think this should happen and Xorg shouldn't allow this either. So for those who have mysteriously high CPUusage from Xorg start closing program by program until you find the culprit. The interesting thing is that after reloading it, the Xor........

  • How to mount/access a single partition from dd image with Linux


    parted sdc.img GNU Parted 1.8.8 Using /home/one/sdc.img Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) unit&nb........

  • Centos how to upgrade from PHP 5.2 to 5.3 without downtime


    This may sound silly but there will be conflicts/issues with the default Centos repository so you have to use a third party like remi (I prefer not to do this but it's the only option unless you migrate your sites/data to another server or can stand some downtime-not an option IMHOon a production server). You may need to upgrade to PHP5.3 to run Joomla or many other reasons. Your host needs to use PHP 5.2.4 or higher to run this version of Jo........

  • How to view an EFI GPT partition in Linux


    Disk /dev/sda: 320.0 GB, 320072933376 bytes 256 heads, 63 sectors/track, 38761 cylinders Units = cylinders of 16128 * 512 = 8257536 bytes Device Boot Start End Blocks Id System /dev/sda1 1 38........

  • Slow KVM Virtual Machine Performance Solved - Choose the right architecture with the CPU flag


    I am running a 64-bit host and was running a 32-bit XPguest which was crawling no matter what I was doing with it,in fact it frequently used 100% CPU power while having no real work load. I experienced with this other guests and wondered why KVM was slow compared to say Xen or Virtualbox. This is because you need to use the "-cpu" flag. For a full list of options run: /usr/libexec/qemu-kvm -cpu ? x86 ........

  • Asus VE247H 23.7" Inch LCD/LED Backlit Monitor Dead/Stuck Pixel Policy Complaint


    I've thought for awhile that Asus has been banking on its years old reputation for quality amongst gamers and enthusiasts and I think I'm right. My Asus VE247H Monitor with a supposed 2MS refresh rate has 1 red/stuck/dead pixel but fortunately it can only be seen on a non-true black picture or against a blue screen. I have several Asus products and find they're all of fairly poor quality. First of all their motherboards have given me the most issues of any brand, they te........

  • Ubuntu 10 Nvidia Drivers Not Updated After Kernel Update Solution/How-To Manually Rebuild nvidia kernel modules for Ubuntu


    I dread updating the kernel and rebooting to find the Ubuntu graphics aren't working and you have to manually intervene. This is usually because Ubuntu for whatever reason didn't update the drivers you need (eg. the manually compiled Nvidia Kernel driver that MUST be recompiled for each and every kernel update unfortunately). The most common reason may be that "linux-source" hasn't been installed automatically on my system. I tried to manually reinstall the........

  • How To Burn ISO Image using cdrtools/dvdrtools for Linux/Unix Ubuntu/Debian/RHEL/Centos etc..


    It really is as simple as: cdrecord -v dev=/dev/sr0 pathtoyourisoimage.iso -v is for verbose, I prefer it but if you don't you won't see as much output like below (I like to know the details and exactly what's happening) dev=/dev/sr0 specifies the device name of your burner (they say not to use it and to specify some weird annoying device string but using the raw /dev has always worked for me and is how it should have been implemented from the start IMHO)........

  • rpmforge: [#### ] 471/10722Segmentation fault yum[18934]: segfault at 0000000000000000 rip 00002ade62153a30 rsp 00007fff76f9fe58 error 4


    A few days ago this happened on multiple Centos 5 servers and apparently anyone using rpmforge was affected by this error and there was no solution other than disabling that repo to fix it. To some this highlighted a few points, that there is a reason RHELexists with full paid support, and also that this could be a vulnerability and huge flaw with yum. A yum search or install should not segfault just because the rpmforge repo goes down. Fortunately it came back up........

  • ifup eth0 SIOCSIFFLAGS: Cannot allocate memory Failed to bring up eth0 Centos Network won't work after kernel update and reboot


    ifup eth0 SIOCSIFFLAGS: Cannot allocate memory Failed to bring up eth0 This is on a Centos 5.5 machine with OpenVZ kernel 2.6.18-238.12.1.el5.028stab091.1PAE, I updated 3 systems with the same hardware to the same kernel and for some reason the network didn't come back. This only happened once the first time I booted into the new kernel and hasn't happened again but this is a serious issue for those running systems from remote locations such as a datacente........

  • How To Test If Your Hard Drive Is Good/Signs of dying hard drive


    I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem: We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........

  • smart is not smart, it thinks a dead drive is still good


    I had a dying drive that smart thought until it totally disappeared was a good drive, and actually all parameters did look fine but this system was causing my system to lockup and other bad behavior: === START OF INFORMATION SECTION === Device Model: WDC WD20EARS-00MVWB0 Serial Number: WD-WMAZ20139 Firmware Version: 50.0AB50 User Capacity: 2,000,398,934,016 bytes Device........

  • Centos Solution to "Warning: Unable to open /dev/fd0 read-write (Read-only file system). /dev/fd0 has been opened read-only."


    Warning: Unable to open /dev/fd0 read-write (Read-only file system). /dev/fd0 has been opened read-only. That's a very annoying error, it's simply because Centos for some reason thinks it's wise to load the "floppy" kernel module, who has a floppy drive? I haven't seen or used a floppy for over 12 years! It's more than just annoying, if you probe the drives attached to your system, eg. with grub or partprobe, it keeps trying to locate a flopp........

  • Hitachi 2TB HDS5C3020ALA632 drive DOA


    I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead): ata1: link is slow to respond, please be patient (ready=0) ata1: softreset failed (device not ready) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: link online but device misclassified, retrying ata1: link is slow to respond, please be patient (ready=0) ata1: softreset f........

  • SMARTCTL additional SMART command testing using short and long tests


    smartctl -t long /dev/sda (note you can specify short, but it's not as thorough as long of course). smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === Sending command: "Execute SMART Extended self-test routine immediately in off-line mode". Drive command "Execute SMART Extended sel........

  • Yahoo Mail (email) DNS Server Out Of Date Problems


    I don't expect this to be solved soon but some of Yahoo's DNS servers are out of whack. I changed the IPs of some nameservers of some domains and now most Yahoo users can't e-mail to those domains! As you can see below by the "No MX or A records for mychangedomain.com", now Yahoo's DNS/mailserver DNS cache is wrong. You would think they would at least have cached the old incorrect records, but instead for some reason their DNS cache has no entry and doesn't seem........

  • Linux - mptbase/MPT Fusion LSI Logic Error mptbase: ioc0: ERROR - didn't initialize properly! (-1)


    kernel 2.6.27.54 Fusion MPT base driver 3.04.07 Copyright (c) 1999-2008 LSI Corporation Fusion MPT SPI Host driver 3.04.07 mptbase: ioc0: Initiating bringup mptbase: ioc0: WARNING - Unexpected doorbell active! mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000001! mptbase: ioc0: ERROR - Diagnostic reset FAILED! (102h) mptbase: ioc0: WARNING - NOT READY! mptbase: ioc0: ERROR - didn't initialize proper........

  • Enable SPAMASSASSIN on Postfix in 5 minutes


    Centos 5 Postfix and SPAMASSASSIN Tutorial yum install spamassassin chkconfig spamassassin on vi /etc/mail/spamassassin/local.cf ############## #required_hits 5 #report_safe 0 #rewrite_header Subject [SPAM] #5 is the least restrictive (means only the most obvious SPAM is caught. 0 is obviously the most restrictive/sensitive and would have lots of false positives require........

  • SPAMASSASSIN Disable OpenWhois RBL (it is dead/defunct/no longer active):


    SPAMASSASSIN Disable OpenWhois RBL (it is dead/defunct/no longer active): You might see this in your headers 2.4 DNS_FROM_OPENWHOIS RBL: Envelope sender listed in bl.open-whois.org comment out this inside /usr/share/spamassassin/72_active.cf ##{ DNS_FROM_OPENWHOIS ifplugin Mail::SpamAssassin::Plugin::DNSEval header DNS_FROM_OPENWHOIS eva........

  • Directadmin DA Install Guide


    yum -y install openssl* gcc-c++ gcc flex g++ make;wget http://www.directadmin.com/setup.sh;chmod +x ./setup.sh;./setup.sh #enable SSL /usr/bin/openssl req -x509 -newkey rsa:1024 -keyout /usr/local/directadmin/conf/cakey.pem -out /usr/local/directadmin/conf/cacert.pem -days 9999 -nodes chown diradmin:diradmin /usr/local/directadmin/conf/cakey.pem chmod 400 /usr/local/directadmin/conf/cakey.pem sed -i "s/SSL=0/SSL=1/g" /usr/local/dire........

  • MySQL NEVER delete ib_logfile0 or ibdata1 or you'll lose data


    don't delete /var/lib/mysql/ib_logfile0 or ibdata1 or mysql won't restart I didn't realize they were internal and not part of replication like the relay files! /usr/libexec/mysqld: ready for connections. Version: '4.1.22-log' socket: '/var/lib/mysql/mysql.sock' port: 3306 Source distribution 110127 16:31:00 [Note] /usr/libexec/mysqld: Normal shutdown 110127 16:31:00 InnoDB: Starting shutdown...........

  • email server messsages rejected without reverse DNS DNS check failure Client host rejected: cannot find your reverse hostname Cannot resolve PTR record


    Basically you should always be 100% sure that whatever IPyour mail server sends out with has reverse DNS/PTR records. Remember that unless you own your IPs then you won't be able to set your own reverse DNS. Even if you were to create a reverse PTR record on your DNS servers it will be ignored. Reverse DNS is queried to pre-assigned DNS servers of your ISP, so therefore you'll need to contact your ISP/Colo/Hosting provider to do a reverse DNS entry. If you don't have........

  • Ubuntu 9.04 Crash


    CPU/Kernel/MB/RAID problem? Jan 5 12:45:05 testbox kernel: [653298.890004] BUG: soft lockup - CPU#0 stuck for 61s! [hal-acl-tool:4168] Jan 5 12:45:05 testbox kernel: [653298.890005] Modules linked in: vmnet vmci vmmon binfmt_misc drbd video output input_polldev ocfs2_stackglue ocfs2_dlmfs ocfs2_dlm ocfs2_nodemanager configfs k8temp hwmon_vid lp snd_hda_intel snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi........

  • Failed to save enabled features : The Suexec command on your system is configured to only run scripts under /var/www, but the Virtualmin base directory is /home. CGI and PHP scripts run as domain owners will not be executed.


    Apache/httpd Failed to save enabled features : The Suexec command on your system is configured to only run scripts under /var/www, but the Virtualmin base directory is /home. CGI and PHP scripts run as domain owners will not be executed. This is because I never edited the Apache Config and Virtualmin config to reflect my new/current updated structure.........

  • Installing Webmin & Enabling SSL


    Webmin Setup Centos 5: wget http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html&ts=1294339690&use_mirror=surfnet [1] 24229 [2] 24230 [root@host ~]# --2011-01-06 21:48:20-- http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html Resolving downloads.sourceforge.net... 216.34.181.........

  • WD (Western Digital) Advanced Format Drive Lagged/Slow Speed/Performance/Design Flaw EAD/EARS problem WDC WD20EARS-00S8B1


    Let the numbers speak for themselves, from what I read the Load_Cycle_Count which is very high (more than 500,000/half a million times) is the number of head parks. What a stupid"Green" design and design flaw which will probably mean an early life for the drive. This is almost as silly as Seagate's new reputation for BSY/poor quality disks since the 7200.11 series. To make it worse this is also when Western Digital introduced "Advanced Format" o........

  • Firefox plugin-container high CPU usage


    This is an easy fix and highlights a huge issue again with Linux and Flash still not playing nicely/working as well as Windows yet. Solution - Go to "about:config" and disable the two entries (set them to false): dom.ipc.plugins.enabled.libflashplayer.so dom.ipc.plugins.enabled.libnptest.so........

  • PHP Email Attachment Corrupt Solution


    I couldn't figure out why this wouldn't work, a test script in the root of my htdocs folder worked fine. Within some subdirectories the same code would produce different base64 results but I didn't know hwy. Archive: /tmp/archive.zip Zip file size: 6888 bytes, number of entries: 92 error [/tmp/archive.zip]: missing 242827681 bytes in zipfile (attempting to process anyway) error [/tmp/archive.zip]: attempt........

  • Buffer I/O error on device fd0, logical block 0


    Virtually no system has a floppy disk drive anymore but you will often find your Linux distribution insists that you do or should have one :) The solution is to remove the floppy module and prevent it from loading on the next reboot. rmmod floppy Centos/RHEL echo "blacklist floppy">> /etc/modprobe.d/blacklist #update initramfs so it takes effect dracut........

  • connect: No buffer space available Oct 18 12:21:03 vps kernel: printk: 177 messages suppressed. Oct 18 12:21:03 vps kernel: Neighbour table overflow.


    ping test.com connect: No buffer space available /var/log/messages Oct 18 12:21:03 vps kernel: printk: 177 messages suppressed. Oct 18 12:21:03 vps kernel: Neighbour table overflow. Solution in /etc/sysctl.conf: net.ipv4.neigh.default.gc_thresh1 = 4096 net.ipv4.neigh.default.gc_thresh2 = 8192 net.ipv4.neigh.default.gc_thresh3 = 8192 net.ipv4.neigh.default.base_reachab........

  • Linux How To Add/Delete A Default Route/Gateway


    Remember to replace "eth0" with your NIC device although usually it will be eth0. Replace 192.168.1.1 with your default gateway, remember you can also add multiple gateways by adding a second/different default gateway. route Kernel IP routing table Destination Gateway Genmask&nb........

  • HeartBeat Error/High Load heartbeat: [7120]: WARN: Gmain_timeout_dispatch: Dispatch function for retransmit request took too long to execute: 20 ms (> 10 ms) (GSource: 0x926b390)


    My LOG is flooded with those messages many times per second. I don't know what is wrong with heartbeat, but restarting the service fixed it.........

  • Ubuntu 10.04 Linux is still not ready for the Desktop world


    I am a huge fan of Linux and the idea of OpenSource but I've said it many times, there are still hurdles in today in 2010 for Linux as a Desktop. Linux is still intended for servers at its very core. This can be changed succesfully though, as Apple has shown us with Mac OS X based on FreeBSD. Half of the issue is lack of driver support and the other half is the Linux Kernel and Window Manages, KDE and GNome still both don't cut it (but they're getting closer). I'll........

  • Linux Burn MP3 CD On the Fly using


    I finally decided to look into some utils that did this, and the first one I found is "mp3burn". It is unbelievable simple and perfect. *2017-11 update and mp3burn is still available in standard repos such as Ubuntu 14/16 so this is a current and working project. Just install the package and it gets all required libraries to convert and then burn's on the fly. And you won't believe how simple it is. I just want to a directory that had the MP3's I wanted t........

  • Use rcconf to edit startup/init.d/init scripts on Debian/Ubuntu based distributions


    I've never understood how to enable and disable services for different run levels in Debian based distros, it's just weird, annoying and doesn't make sense. I much prefer chkconfig from RHEL. Just install the package called 'rcconf' and be done with it. rcconf makes things easy for you. apt-get install rcconf Reading package lists... Done Building dependency tree Reading state information... Done........

  • MySQL Recover/Reset Lost/Forgotten root Password


    One note is to secure MySQL, I don't know for sure but I believe you could login to MySQL remotely with no password during this operation (I'm not sure, maybe it doesn't accept blank passwords but I firewall MySQL port anyway and recommend you do the same). First edit /etc/my.cf Under the [mysqld] field add the following line somewhere: skip-grant-tables Now restart mysql: service mysql restart or on Debian sty........

  • Gigabyte GA-H57M-USB3 Complaint Review/Comments


    I'm not impressed with this motherboard, I was impressed with my Gigabyte AM3 board which seems to work flawlessly. Everyone knows that the firmware is flawed, even though I have the F6, it still seems that the system doesn't reset properly or quickly enough. Another HUGE problem is that in most Linux kernels the NIC won't work (if you try 10 times by rebooting it might). I also notice that you need to power down for it to work. This board does not seem very com........

  • Compile PHP 5.3.2 on Centos 5 and CPanel/WHM because of error - Fatal error: Call to > undefined function imagecreatefromjpeg()


    This function and others may not work with the stock PHPinstall on Centos/CPanel: Fatal error: Call to > undefined function imagecreatefromjpeg() Even with libjpeg-devel installed it won't work because PHP was not compiled with jpeg support, so we have to do the dirty work ourselves :) Here is the command/yum's I did to install missing libraries for PHP that configure will complain about (yes it is a one by one process). yum install bzip2-........

  • Unixbench Score on Core i5 750 with OpenVZ Kernel vs Xen/Openvz


    This was unbelievable how much the Xen kernel slows things down, keep in mind both tests were done on the hostnode, one was with the Openvz-Xen hybrid kernel and the other was just OpenVZ. You can see the performance difference is nearly 300% better when not using the Xen kernel. OpenVZ-Xen Kernel Test Results (I was wondering what was wrong/so slow with my Core i5!) # # # # # #&n........

  • Asus Eee PC 1000HE Crashed/Need To Recover/Restore Windows? Easy Solution is Hitting F9


    I'm not a fan of Asus and won't be buying another because of having to fight Asus over a bogus warranty denial (it's a long story but they only replied about how to RMA my unit weeks later on the EXACT day the warranty expired). Anyway, it's just a matter of hitting F9 to do this, there's no need to worry about booting from USB or CD (unless of course you want a different OS eg. Windows XP Pro, Vista/7, or a flavor of Linux or Unix). Also remember that you need to fully/properl........

  • get_printer_attrs: resource name '/printers/printers' no good! - cups error


    This is what the /var/log/cups/error.log says after my Samsung CLP-310N decided to stop printing. This is a new printer that replaced my CLP-300 and it has been working for a day so far. What happened is that I lifted the top part (not realizing there were rollers on it) and it stopped printing. The network activity light was flashing ,hitting the stop button didn't do anything. Even powering the printer on and off did not help. I have restarted CUPS and SMB on the........

  • Seagate Drive 500GB Drive Dying


    This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device........

  • Seagate 7200.11 firmware defect in 500GB, 1000GB (1TB) and 1500GB (1.5TB) Hard Drives


    Seagate Inventory/Firmware Check I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate. *Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate! Seagate Inventory/Firm........

  • Linux EXT3 16GB-17GB maximum filesize issue solved/how to fix


    I have no idea why but mkfs.ext3 defaults to a patheticlly small blocksize of 1024 bytes/1KB (kilobyte). That means the maximum filesize is ONLY 16GB! With 2KB/2048 bytes you get a 256 GB maximum filesize, and with 4KB/4096 bytes you get 2TB! I finally noticed/paid attention to this after realizing that with rsync and scp that no file larger than 17GB could be transferred. I then realized it must be a file size limit on the partition. Here is what tune2fs tol........

  • Picking an FTPD (vsftpd) Server in Linux Centos/Debian


    I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find. yum search ftp Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * rpmforge: ftp-stud.fht-esslingen.de * base: mirrors.netdna.com * updates: updates.interworx.info * addons: yum.singlehop.com * extras: mirrors.netdna.com rpmforge........

  • Compaq V2405CA Laptop - Unixbench Performance Test


    Here are the results, it is Sempron 3000+ AMD Mobile, 500Gig HDD, 512MB RAM with shared ATI Radeon graphics. # # # # # # # ##### ###### # # #### # # # # ## # # # #&nb........

  • PHP cannot access /usr/bin/openssl


    PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist: [code:1:1fd0f3abbe] if (!file_exists($OPENSSL)) { //echo "ERROR: OPENSSL $OPENSSL not foundn"; }[/code:1:1fd0f3abbe] I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........

  • JavaScript how to do math arithmetic with floats and int


    JavaScript how to do math arithmetic with floats and intI have 3 variables some of which are just int and some float and need to find their sum It just adds them as strings for some reason.Normally this would work but the floats were actually text technically I guess since they came from a form. You need to convert them using parseFloat() and then everything is fine.........

  • Javascript round float to 2 decimal places


    Javascript round float to 2 decimal places[code:1:7d628eaf94] totalprice = Math.round(totalprice*100)/100;[/code:1:7d628eaf94] substitute the second instance of totalprice with the variable that needs to be rounded to 2 decimal places........

  • Great sound tutorial


    Great sound tutorialThis is great if you need users to be able to start/stop playing sound on your page with the click of a button. http://www.smartwebby.com/Flash/sound_button.aspHere's a simple one except that it doesn't do rollovers. http://www.flash-here.com/tutorials/flash_play_sound.html I actually could not get the rollovers to work using the other tutorial so it is either a mistake on the webmaster's part or........

  • Upgrade Release Kernel Tips


    Upgrade Release Kernel TipsThis is for CentOS 3.1 to 3.8 but the methodology will apply everywhere. I ran into a problem first of all with a non-booting system after running #yum update centos-release It took me to 3.8 and upgraded all the other packages [b:7e931c835d]BUT[/b:7e931c835d] because of some stupid flags enabled in /etc/yum.conf the KERNEL WASN'T UPGRADED SO AFTER BOOTING, WELL IT DIDN'T BOOT OF COURSE :) H........

  • Intel's Finnish Fetish


    Intel's Finnish FetishIntel's Finnish Fetish By Dave Mock June 13, 2005 Chipmaker Intel (NASDAQ: INTC) has successfully topped the personal computer market for decades. Breaking into related areas such as communications has been much difficult for the world's largest semiconductor maker. But a new partnership with Nokia (NYSE: NOK) could help to change that. Intel's forays into cellular-phone and home-entertaiment-device chips have........

  • Bash Script Info


    Bash Script Infohttp://www.faqs.org/docs/Linux-HOWTO/Bash-Prog-Intro-HOWTO.html#ss10.5 http://www.scit.wlv.ac.uk/~jphb/spos/notes/shell/shell5.html http://quong.best.vwh.net/shellin20/#LtohTOCentry-41 http://www.cactus.org/~dak/shellscript.html http://db.ilug-bom.org.in/Documentation/abs-guide/ http://pegasus.rutgers.edu/~elflord/unix/bash-tute.html http://heather.cs.ucdavis.edu/~matloff/UnixAndC/Unix/CShellII.html Since bash i........

  • CDR Manufacturers - Why is so much media bad?


    CDR Manufacturers - Why is so much media bad?I have searched for good media and tried many kinds for years. I guess I'll try to summarize my findings and conclusions. Dye is irrelevant, dye of any color can be good or bad, it more likely depends on the manufacturer. Speaking of manufacturers, the name at the top of the disc means nothing. For example, Memorex along with any other 'brand' is actually always made by another manufaturer including CMC Mag........

  • ECS K7S5A Motherboard System Take Up To 2 Minutes To Boot


    ECS K7S5A Motherboard System Take Up To 2 Minutes To BootHi guys, My motherboard is very strange. Sometimes it will take up to a few minutes to post. I have no idea it suddenly started doing this. I have tried everything and all I can figure is that it is somehow related to the USB ports possibly. Why do I say this? Because if I disconnect my scanner the problem occurs less frequently. I only have a printer hooked up to USB now and by........

  • Use Mozilla Firefox, not Internet Explorer - You'll be glad!


    Use Mozilla Firefox, not Internet Explorer - You'll be glad!Hey guys, I just thought I'd recommend that everyone switch to Mozilla Firefox as their web browser. You can find it at http://mozilla.org It is free and it is much better than IE. It has a built-in popup blocker which works great and most importantly, it doesn't have a million critical security flaws which could compromise your security such as passwords for on-line banking etc..........

  • Enable/Disable PHP Warnings/Logs and Errors from .htaccess with Apache


    Put what you see below into your .htaccessand it will enable errors and notices. (change on to off and 1 to 0 to disable though) php_flag display_startup_errors on php_flag display_errors on php_flag html_errors on Now you'll be able to see errors and notices but this should really only be used for debugging purposes and only temporarily as it can be a security issue since errors can reveal information you wouldn't want hacker........

  • Adventures in pre-paid SIM Cards and data GPRS/Edge/3G in China with China Mobile in Shenzhen, Guangzhou, Shanghai, Beijing and other cities


    This really is a difficult and confusing process for non-Mandarin speakers, but here's what I've done and learned so far: You can purchase an "M-Zone" China Mobile pre-paid SIMCard from almost anywhere but I tried to purchase mine from Suning (a large electronics dealer) hoping they would be able to help me or answer my questions but my plan didn't work out at all. At Suning once I found someone who spoke some English they gave me the 55 RMB M-Zone China Mobile P........

  • The power of passive vs air cooling. Small fans make a world of difference.


    I bought a Dynatron A46G for my AMD X4 620 AM3 Quad Core CPU. Just judging by touch, the stock OEM fan/heatsink combo kept things so cool, I could leave the 1U server on the floor and it barely felt warm to the touch, including the heatsink itself. I thought the Dynatron A46G would be enough with passive cooling (it has no fan), but the same setup became burning hot on the underside of the server and also by touching the heatsink itself within minutes. I thought that th........

  • GRUB "Error 2: Bad file or directory type" 0.97 won


    You can see the problem below, GRUB recognizes my hard drive and sees the partitions but cannot access them. This is from the GRUB boot disc I'm using. What happened is that I had some power issues causing this system's power to be interrupted several times and basically an on/off on/off situation. The system won't boot, I just get a flashing cursor and no message or error from GRUB. Obviously the problem is that my MBR seems corrupt or some other issue. My........

  • Unixbench Score with Glusterfs/Openvz & Quad Core Xeon - Updated with GlusterFS 2.0.8 & Optimized Client Config


    The results are still not flattering and are nothing close to native performance. Unless GlusterFS has a "DRBD-like" option to delay writes over the network and to only read from the client side, I don't see how performance can ever improve much more. After doing some client optimizations Iadded more to the score: Start Benchmark Run: Sun Nov 29 00:37:44 PST 2009 00:37:44 up 3 min, 1 user, load average: 0.01........

  • Clustered/Distributed Network Filesystems, Which Ones live up to the hype?


    I've tried to find a good sensible solution to cluster with and each technology has it's pros and cons and there is no perfect solution and I've found a lot of "exaggerations" in the applications, benefits and performance of these different filesystems. DRBD I first started off with DRBD and Ihave to say it does live up to the hype, is quite reliable (although it can be annoying to match up the kernel module and user applications since they must match and whe........

  • sudo: Error dropping capabilities, aborting in Linux Centos 5.3


    For some reason Ikeep getting this error when trying to run a sudo command eg: sudo -u someuser somecommand sudo: Error dropping capabilities, aborting My version of sudo is:sudo-1.6.9p17-3.el5_3.1 and I've heard that version 1.7 fixes everything. The only thing is yum does not think sudo has any update. Iguess the new version has not been committed to the RPM repository yet. This is really a huge and ann........

  • Have an OpenVZ VPS/Linux Virtual Private Server and nothing works right?


    A VPS Server I had just wasn't working right, code that I migrated there just wasn't working. For example, it kept telling me the connection to the database was unsuccessful, halfway through iterating through results it already had. Then I realized it wasn't my code. Ichecked my /proc/user_beancounters and found this: cat /proc/user_beancounters Version: 2.5 uid resource held maxheld barrier limit failcnt........

  • Apple iPhone 3GS and predecessors are leading a revolution


    As much of a computer nerd as Iam, I'm usually a late adopter to technology for a few reasons. Ifeel most new hyped technologies and electronics are mainly fads, and I'm also cheap. Adopting later means you avoid the bugs, kinks and most importantly pay the lowest price, that's me being cheap again :) I never read much about the iPhone but Isaw all the hype around it and until recently I wasn't a big fan of anything Apple until a few years ago I realize........

  • Nokia N97 review, feedback and complaints


    I've had an old Blackberry for a few years and I was ready to spend some serious cash on a nice Nokia. I love the idea of the Linux based Symbian S60 OS, so I was looking at phones like the E63, E71 (both are basically the same, at least CPU/screensize although E71 is thinner, has a 3MP camera, has GPS, and has dedicated buttons to adjust the volume). Then Iheard about the N97 and what a revolution it was supposed to be and it was even compared to iPhone. To........

  • SIOCSIFADDR No such device eth0 error while getting interface flags - eth0 Ethernet Device can


    Igot this after copying a VMWare image onto another machine in Debian. SIOCSIFADDR No such device eth0 error while getting interface flags The solution 1.) Find and edit the device line in persisent-net.rules note it will be prefixed with something like z25 or something else. vi /etc/udev/rules.d/z25_persistent-net.rules The easiest way is to comment anything out. If you are feeling........

  • OCFS2 crash


    When trying to even cd or ls the mounted OCFS2 partition it crashes. Ithink this is a combination of VMWare Server's problem and the way I mounted and symlinked to it. More than anything this shows the problem and lack of forsight with VMWare, but also that OCFS2 is easily crashed if you do strange things. Output of /var/log/messages for OCFS2 Apr 10 15:57:45 localhost kernel: [84331.691258] Modules linked in: vmnet vmci vmmon ocfs2_stac........

  • 1U Servers are Loud - We Have The Quiet Solution


    I've read a lot of people complaining that their 1U servers are too loud for the office, home or whatever strange places people might want to put them. Whenever Isee the question asked, "what can be done about the noise", you'll see a myriad of silly answers like "you shouldn't have it at home or in your office at all", "1U servers are meant to be loud". These all might be valid points but they're not the solution. A good example is a........

  • Rackable Systems and their Microslice Clustered 1U Servers


    Ithink there has been a lot of negative press towards Rackable Systems. We will give their new solution credit that it is marketed very well, and comes prepackaged and ready to go. But let's cut through the hype of both sides, the people who love this concept and the people who hate it. What Rackable Systems have done is a first, to minimize space, power and costs into small servers. This is great, and many companies have already built their own servers based........

    • Latest Articles

  • How to combine .txt ACLs without breaking things
  • How to ping all of Googlebot's IPs script
  • 'virtio0' uses a qcow2 feature which is not supported by this qemu version: QCOW version 3
  • Linux bash script to get the IP of a list of hostnames
  • How To Use Camera Webcam in Docker for OBS Studio etc...
  • Computer Server Won't Post Boot Or Enter BIOS Setup After Installing RAID SAS or GPU Card etc..
  • How To Test PHP Scripts from CLI with GET variables/query string
  • apt-cache how to see all available versions of a package in Debian Ubuntu Mint
  • Virtualbox VBox Guest-utils drag and drop files stops working with Windows VMs
  • How To Remove Ubuntu Netplan and Go Back to /etc/network/interfaces
  • How To Force Flash an AMD Instinct GPU To Another Model Using Debian Ubuntu Mint Linux
  • How To compile ollama from source to use unsupported AMD GPU with rocm in Ubuntu Debian
  • QEMU KVM Virtio GPU Windows Cannot Select 1080P
  • Linux Gnome Desktop Ubuntu Mint Debian Gets Slower After Weeks
  • Firefox How to Save Full Page As Screenshot/PDF
  • Nvidia Datacenter Driver Tesla Slow nvidia-smi response and high utilization with 0 usage
  • ffmpeg how to normalize / increase the volume of your audio
  • kdenlive audio blips pops cracks artifacts solution fix
  • haproxy / nginx certbot SSL issues
  • nginx how to see the real IP when behind a CDN
    • Copyright © realtechtalk.com 2026