• Firefox Cannot Hit Enter Key In Address Bar and Location History Not Working


    Opening Firefox from the CLI reveals the following as the cause of the error: Query failed: Error: Error(s) encountered during statement execution: no such table: moz_favicons The symptoms of this issue are that in the address bar you cannot hit enter to browse to a site/url/address and your history cannot be accessed, nor does your history show up in the address bar when typing previously used addresses. This usually happens because you've........
  • Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM


    The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........
  • Adobe Acrobat Reader for Linux to use and view XFA Fillable Forms


    The reason for not being able to read one of these dreaded/ fillable "XFA" forms is because no Linux PDF reader that I'm aware of supports them. Part of this reasoning is for security. It is really silly, they should ban these XFA forms or at least replace the Please Wait with the non-fillable version. Download Adobe Reader 9.5 for Linux from here: This is the solution but only so much, at least for me I was able to view th........
  • VirtualBox How To Add iSCSI Storage using VBoxManage


    #to show all VBoxManage list vms #show ONLY running vms VBoxManage list runningvms VBoxManage storageattach test --storagectl "SATA" --port 0 --device 0 --type hdd --medium iscsi --server 192.168.1.91 --target "iqn.2018-12.local.abcrandom.target:sdb" --initiator "iqn.1982-01.ca.bla.tld:abc123" --t........
  • How To Mathematically Convert and Calculate Binary Value To Decimal Value


    When converting binary the easiest way is to write out a vertical list in a format like below and follow the formula in the table. Example Convert 1101 1111 to decimal. Step 1.) Write out the binary below in vertical form (leave lots of space on the left side). Keep this in mind that the "previous sum" starts at 0 on your first line. Step 2.) Formula: 2 *........
  • hwloc-nox set CPU affinity in Linux


    sudo apt-get install hwloc-nox Reading package lists... Done Building dependency tree Reading state information... Done The following NEW packages will be installed: hwloc-nox 0 upgraded, 1 newly installed, 0 to remove and 530 not upgraded. Need to get 151 kB of archives. After this operation, 453 kB of additional disk space will be used. Get:1 http://archive.ubuntu.com/ubunt........
  • Debian Mint Ubuntu compiling xmr-stak


    sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........
  • wodim / cdrecord error cannot burn DVD or BDR .iso Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error


    dvd+rw-mediainfo /dev/sr0 INQUIRY: [ASUS ][BW-16D1HT ][3.00] GET [CURRENT] CONFIGURATION: Mounted Media: 11h, DVD-R Sequential Media ID: RITEKF1&n........
  • linux mint image convert menu option missing solution


    Ialready have the caja-image-converter option installed but it shows nothing. Weirdly enough if you install nemo and nautilus converter it does show and work inside caja: The solution is to install *-image-converter sudo apt-get install *-image-converter Reading package lists... Done Building dependency tree Reading state information... Done Note, selecting 'n........
  • VSphere InternalServerError - Error When Adding Permissions


    InternalServerError (com.vmware.vapi.std.errors.internal_server_error) => { messages = [LocalizableMessage (com.vmware.vapi.std.localizable_message) => { id = vapi.bindings.method.impl.unexpected, defaultMessage = Provider method implementation threw unexpected exception: com.vmware.vapi.std.errors.InternalServerError, args = [com.vmware.vapi.std.errors.InternalServerError] }], data = } I was getting the........
  • VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI


    #mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........
  • named [FAILED] - zone 1.168.192.in-addr.arpa/IN: not loaded due to errors. - bind error solution


    Centos when copying old files and restarting it seems load everything fine and then says [FAILED] with no log or other message. service restart named named [FAILED] Check more thoroughly you may have missed the error if you have lots of zones! service named restart|grep error zone 1.168.192.in-addr.arpa/IN: not loaded due to errors. zone 2.168.192.in-addr.arpa/IN: no........
  • No comments are allowed here Internal Server Error The server encountered an internal error or misconfiguration and was unable to complete your request.


    Internal Server Error The server encountered an internal error or misconfiguration and was unable to complete your request. Please contact the server administrator, root@localhost and inform them of the time the error occurred, and anything you might have done that may have caused the error. More information about this error may be available in the server error log. Apache/2.2.15 (CentOS) Server at testdomain.com Port 80........
  • Linux Mint Black Screen after boot no graphics solution


    This is not the normal "black screen"issue and I was shocked to eventually find out why. The normal advice of reconfiguring Xorg didn't work. Even booting into "Recovery Mode" did not help. Here is the short end of the stick that fixed it: sudo apt-get install mdm mate-desktop-environment Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled. This must be whe........
  • Linux Ubuntu Mint Debian cannot play xvid,x264,mp4 or any videos codec issue - xplayer Could not initialize supporting library.


    In xplayer Iget the following error "Could not initialize supporting library.". It actually looks more like a gstreamer issue. For those wondering what the default video player is called it is "xvid" and not "totem" anymore like previous versions. Basically it looks like some codecs are missing when I uninstalled another program it uninstalled other programs and codecs that it shouldn't have. I've tried installing all the gstre........
  • Linux how to view video card make and exact model


    Normally lspci will show you just like this and would suggest they are exactly the same card: 1a:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Ellesmere [Radeon RX 470/480/570/580] (rev e7) 1c:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Ellesmere [Radeon RX 470/480/570/580] (rev e7) lspci -vnn is the answer As we can see one is a Gigabyte and the other is an MSI card. Wha........
  • How to Update Linux /usr/share/misc/pci.ids


    This works with lspci and if it's outdated may not give you the exact manufacturer and device model. For example take these 3 different RX 580's: 1a:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Device 67df (rev e7) 1b:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Device 67df (rev e7) 1d:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Device 67df (rev e7) You ca........
  • kdenlive - No LADSPA plugins were found! Check your LADSPA_PATH environment variable. [producer_xml] failed to load transition "qtblend"


    This happens if you are running a kdenlive script from the shell of a remote machine without using SSH "-X" forwarding and it will also cause any areas where you write text to be a white screen for that duration. melt FusionFestival.kdenlive No LADSPA plugins were found! Check your LADSPA_PATH environment variable. [producer_xml] failed to load transition "qtblend" [producer_xml] failed to load transition &q........
  • kdenlive titles/text renders as white screen when using .sh script


    When using the .sh script the rendering doesn't work after an upgrade of related packages to kdenlive. kdenlive (kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1)) with affine or composite transitions was fine but is now broken during the time of transition it is just a white screen. The previous version was fine: kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1 But now I can't find it or install it:........
  • ffmpeg trouble concatenating similar but different files


    When things go wrong your video is basically unplayable or the first video plays fine and then freezes when moving on to the next. Generally if both videos weren't produced with the exact 100% same settings you will have issues. You can try the basic concat but it often won't work right. Solution for me: My example uses 3 videos in total so "n=3" and a=1 to include audio. ffmpeg -threads 12 -i file1.mp4 -........
  • ffmpeg Linux Mint download, compile and install howto


    #if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2 tar -jxvf ffmpeg-3.3.2.tar.bz2 cd ffmpeg-3.3.2/ ./configure --disable-yasm install prefix /usr/local source path ........
  • How to change reserved blocks in Linux partition


    user@box:~$ sudo tune2fs -l /dev/md99 [sudo] password for user: tune2fs 1.42.9 (4-Feb-2014) Filesystem volume name: Last mounted on: /mnt/md50 Filesystem UUID: 976a8655-2619-4587-878c-dab07f7b7652 Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Fi........
  • Centos 7 Cudaminer Nvidia setup guide


    I am using a GTX 1060 but replace the download for the driver with the correct/current version for your particular card by visiting: http://www.nvidia.com/Download/index.aspx?lang=en-us yum install automake curl openssl-devel libcurl-devel gcc gcc-c++ yum -y install kernel-devel-`uname -r` yum -y install unzip #the........
  • USB 3.0 PCI x1 Card Review VIA VL805 on Linux Review and Experience


    This is a VIA made VL805 USB 3.0 Chipset with 4-ports and MOLEX powered. First of all this unit was cheap at about only 9 USD with fast shipping. My biggest concern was if this was a quality unit and would it really give you full USB 3.0 speeds (some people reported with similar cards that for some weird r........
  • Openshot 2.2 is very unstable always crashing in Linux Mint 18.1!


    Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Missing folder chosen by user: Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Removed missing file: MAH02949.MP4 Jun 1 15:45:57 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: ui_util:WARNING Icon theme media-playback-start not found. Will use backup........
  • Track 01: 34 of 1726 MB written (fifo 100%) [buf 99%] 3.6x.Errno: 5 (Input/output error), write_g1 scsi sendcmd: cmd timeout after 1.897 (40) s CDB: 2A 00 00 00 44 A9 00 00 1F 00 resid: 6144 cmd finished after 1.897s timeout 40s write track da


    These errors believe it or not are simply because of not being the root user or running with sudo! However if you didn't know to try as root you'd think there was a problem with your burner or disc Essentially it looks like without root you cannot send the required scsi commands to continue writing. Ithink cdrecord should have built-in tests or safeguards to see if it has the permissions to run the required commands. I guess for more advanced users the idea is simila........
  • mdadm frozen and doesn't realize array is dead/missing failed due to unplugged drives


    This was a surprising bug but I unplugged all drives for an array md127. At first it was just 1 drive and mdadm seemed to notice this. I unplugged the second drive taking the array offline but mdadm did not realize it was offline and still showed a non-existent disk as being part of it. This created problems trying to unmount it or even to stop this array with mdadm freezing. As for how to fix it I can only think of making sure you are not in a mounted path of........
  • apc_shm_attach: shmat failed: in Unknown on line 0 & apc_shm_create: shmget(0, 67108864, 914) failed PHP Solution


    PHP Fatal error: PHP Startup: apc_shm_create: shmget(0, 67108864, 914) failed: Invalid argument. It is possible that the chosen SHM segment size is higher than the operation system allows. Linux has usually a default limit of 32MB per segment. in Unknown on line 0 PHP Fatal error: PHP Startup: apc_shm_attach: shmat failed: in Unknown on line 0 This error is not at all fun because it actually prevents Apache/httpd from starting or working at all. It will........
  • ADATA SU800 256GB 3D NAND Flash SSD Test & Review


    I keep reading these drives are slower, but they are cheap and still SSDand work very fast for my needs. As you can see the sequential read is 481-491MB/s, if I put them in MDADM RAID10 mode (normal RAID1) they should give me well over 900MB/s and with redundancy and being very cheap for what they offer. [1232206.315622] scsi 8:0:1:0: Direct-Access ATA ADATA SU800&........
  • Linux Mint 17 How to Enable File Sharing Option in File Manager


    I still cannot understand how this would not be enabled by default and I struggled to find the reason why with manually installing samba etc.. wondering why the option for sharing was not in the menu. On Linux Mint "MATE" the package is called "caja-share" and on Cinnamon it is called "nemo-share" so edit the below command as necessary: *Also note that the "samba" package is necessary as it is not inst........
  • Centos and obfsproxy install errors


    pip install obfsproxy /usr/lib/python2.6/site-packages/pip/_vendor/requests/packages/urllib3/util/ssl_.py:90: InsecurePlatformWarning: A true SSLContext object is not available. This prevents urllib3 from configuring SSL appropriately and may cause certain SSL connections to fail. For more information, see https://urllib3.readthedocs.org/en/latest/security.html#insecureplatformwarning. InsecurePlatformWarning You are using pip version 7.1.0, however version 8.1.1 i........
  • There was a problem importing one of the Python modules required to run yum. The error leading to this problem was:


    There was a problem importing one of the Python modules required to run yum. The error leading to this problem was: No module named yum Please install a package which provides this module, or verify that the module is installed correctly. It's possible that the above module doesn't match the current version of Python, which is: 2.7.9 (default, Apr 21 2016, 16:51:58) [GCC 4.4.7 20120313........
  • Nvidia Linux Card not working due to LSI 9200/SAS2008 IRQ conflict


    At first my BIOS said the card may not work right because there is no more option ROM space. I disabled the Option ROM for both LSI 1068 and 2008 chipsets, Network Boot ROM and most other PCI slots, Serial Port, etc... and the message went away but the card still does not work properly. But it still cannot initialize the card properly(does not work): [ 33.943272] NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:........
  • Apache Vhost HowTo Serve Same Content using a different domain and IP


    There are a few ways of doing this and all basically involve using the reverse proxy or "ProxyPass" feature of Apache to accomplish it. 1.) Create a normal vhost and simply symlink the root directory of the site you want to mirror. Eg. originalsite.com and newsite.com /vhosts/originalsite.com/httpdocs You would symlink like this: ln -s /vhosts/originalsite.com/httpdocs vhosts/originalsite.com/........
  • Virtualbox errors on Ubuntu/Debian/Mint


    The solution was to reinstall the vbox dkms package and do a manual modprobe of the modules it makes. I never sorted out the unable to start due to the USB issue, I did have the guest additions installed but the only way to boot was to change the pointing device from USB to PS2 and then to disable the USB controller (if your pointing device is set as USB, disabling USB will not work because it will re-enable by default when it sees your pointing device is USB, this is w........
  • Installing zoneminder on Ubuntu/Debian Linux Howto


    sudo apt-get install zoneminder [sudo] password for one: Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: libuser-perl python-evince kdebase-apps kwrite unixodbc libgnomeprint2.2-data python-soappy vgabios python-metacity hddtemp python-mediaprof........
  • status: { DRDY ERR } error: { ICRC ABRT } failed command: WRITE FPDMA QUEUED MCP55 Linux Errors


    [ 2868.041375] ata1: EH in SWNCQ mode,QC:qc_active 0x40 sactive 0x40 [ 2868.041554] ata1: SWNCQ:qc_active 0x40 defer_bits 0x0 last_issue_tag 0x6 [ 2868.041556] dhfis 0x40 dmafis 0x40 sdbfis 0x20 [ 2868.041874] ata1: ATA_REG 0x41 ERR_REG 0x84 [ 2868.042013] ata1: tag : dhfis dmafis sdbfis sactive [ 2868.042163] ata1: tag 0x6: 1 1 0 1 [ 2868.042301] ata1.00: exception Emask 0x1 SAct 0x40 SErr 0x400000 action 0x6 frozen [........
  • HP Procurve Switch 2824 CLI Telnet Experience , Guide and Tutorial


    telnet 192.168.1.54 ------------------------------------- ProCurve J4903A Switch 2824 Software revision I.10.77 Copyright (C) 1991-2009 Hewlett-Packard Co. All Rights Reserved. RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by the Government is subject........
  • Dell CS24-NV7 lspci dmidecode info


    0000:00:00.0 RAM memory: NVIDIA Corporation MCP55 Memory Controller (rev a2) 0000:00:01.0 ISA bridge: NVIDIA Corporation MCP55 LPC Bridge (rev a3) 0000:00:01.1 SMBus: NVIDIA Corporation MCP55 SMBus (rev a3) 0000:00:02.0 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a1) 0000:00:02.1 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a2) 0000:00:05.0 IDE interface: NVIDIA Corporation MCP55 SATA Controller (rev a3) 0000:00:05.1 I........
  • Dell CS24SC Server Info


    Dell CS24SC Info 0000:00:00.0 Host bridge: Intel Corporation 5100 Chipset Memory Controller Hub (rev 90) 0000:00:02.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x8 Port 2-3 (rev 90) 0000:00:03.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x4 Port 3 (rev 90) 0000:00:04.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x16 Port 4-7 (rev 90) 0000:00:05.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x4 Port 5 (rev 90)........
  • Dell CS10-F1D Server Info lspci Linux specs


    0000:00:00.0 Host bridge: Intel Corporation 5000P Chipset Memory Controller Hub (rev b1) 0000:00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 (rev b1) 0000:00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 (rev b1) 0000:00:04.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 (rev b1) 0000:00:05.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4........
  • Linux disable firmware prevents NIC/Ethernet from working phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.


    [ 17.208336] tg3 0000:08:00.0: eth0: Link is up at 1000 Mbps, full duplex [ 17.210194] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX [ 76.000065] phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware. [ 76.002332] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 86.736004] eth0: no IPv6 routers present [ 148.960038] phy0 -> rt2x00lib_request_fi........
  • OpenVZ vzctl update changes how iptables work - iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. updated solution


    Are you getting the same old error message even though your iptables settings for OpenVZ are correct? iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. The reason is because in newer vzctl the old way of setting IPTABLES="" in vz.conf is completely deprecated (I spent some time fiddling wondering why my settings were correct but........
  • Vbox/Virtualbox devices grayed out for non-root user solution


    It is a permissions issue that is hard to fix. All but one USB device is greyed out. I am already a member of "vboxusers" I have already enabled and disabled USB support for the guest. I have already reinstalled the latest VBOx guest editions If running as root it all works fine Changing........
  • Samsung C410W/CLP410W not printing in Linux solution


    You need to use the Samsung driver but specify it as a CLP-360 (this is what I used for my CLP365) and incidentally most of these units look identical on the outside on inside (I've been buying whatever the latest C300 and now 400 unit for years which all seem the same with slightly different features that I never use). The solution Once again try specifying earlier models and revisions if the printer doesn't print (it will say it's been sent to the printer bu........
  • Webalizer Error Error: Unable to restore run data (11) Error: Unable to restore run data (11) Solution


    Error: Unable to restore run data (10) Error: Unable to restore run data (11) Ikeep getting this error but so far there is no obvious solution. Sometimes I've had to remove the *.hist files so I'll try that again. *Update This is an ongoing random problem after months of running webalizer it runs into some problem that can only be fixed by removing the following files so it can rebuild the stats (you end up losing p........
  • drbd won't create device if previous partition is on it Command 'drbdmeta 0 v08 /dev/md160 internal create-md' terminated with exit code 40


    This is what fixed it: [root@box13 ~]# dd if=/dev/zero of=/dev/md160 bs=512 count=500 Basically you need to wipe out more than just the 512 byte partition table so 512 bytes * 500 is more than enough to make DRBD happy and think the partition is now empty. The reason this happens is because it gets confused when there is a previous partition with data on the device you are using. root@box13 ~]# d........
  • Asterisk iptables block bruteforce attacks howto with fail2ban


    yum -y install fail2ban vi /etc/fail2ban/jail.conf [asterisk-tcp] enabled = true filter = asterisk action = iptables-multiport[name=asterisk-tcp, port="5060,5061", protocol=tcp] sendmail-whois[name=Asterisk, dest=you@example.com, sender=fail2ban@example.com] logpath = /var/log/asterisk/messages maxret........
  • kvm centos cannot compile error


    ./configure ./configure: cannot locate gcc 3.x. please install it or specify with --qemu-cc yum -y install gcc make ./configure ./configure: cannot locate gcc 3.x. please install it or specify with --qemu-cc yum -y install compat-gcc-* ./configure Error: Could not find alsa Make sure to have the alsa libs and headers installed. yum -y install alsa-lib-devel ./configure........
  • strange kernel dmesg errors


    Sep 26 16:56:21 box kernel: 00 00 00 00 00 00 00 00 Sep 26 16:56:21 box kernel: [37007.155690] d_alias libdl-2.12.so d_count=9 d_flags=8 Sep 26 16:56:21 box kernel: [37007.155697] 09 00 00 00 08 00 00 00 9f 05 9f 05 00 00 00 00 c0 71 1d 18 04 88 ff ff 00 00 00 00 00 00 00 00 a0 7e 48 00 00 c9 ff ff 78 a9 21 18 04 88 ff ff 3a 7b fa 4e 0d 00 00 00 98 5c 2d 18 04 88 ff ff 18 5c 2d 18 04 88 ff ff 18 5c 2d 18 04 88 ff ff 00 01 10 00 00 00 ad de 00 02 20 00 00 00 ad de f8........
  • Dell SAS 6/ir Cards are just LSi 1068E cards


    02:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1068E PCI-Express Fusion-MPT SAS (rev 08) 03:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1068E PCI-Express Fusion-MPT SAS (rev 08) Basically these cards are a stripped-down version of Dell Perc 6/i only they (SAS 6/ir) support JBOD. The DellPerc 6/i are basically useless because it doesn't have JBOD support and requires software or BIOS commands to add or remove........
  • Unixbench Testing


    The first is a dual CPU AMD Opteron 2373EE (4 cores x 2) and I think it did bad because it has some old 250GB SATAs which can only do about 65MB/s max sequential reads. I think it should have blown away the second (AMD X4 640 Quad Core). [root@fs12home unixbench-4.1.0-wht-2]# ./Run make all make[1]: Entering directory `/root/unixbench-4.1.0-wht-2' Checking distribution of files ./pgms exists ./src exists........
  • Dell FS12-NV7 2U Server Information and Guide


    I've got one of these for testing projects from work at home and got more than I bargained for with the time I've spent on it due to the storage handing/Perc 6/i cards. My particular model came with the following: 2U Rack Mount Server with Rails 2xOpteron 2373 EE (Quad Core, there is a 6-core version that can be found at times) 16GB RAM 2 x 250GB Seagate SATA 2 x Dell Perc 6/i (horrible and a nightmare to work........
  • Dell Perci 6/i Firmware Upgrade Guide Tutorial


    One thing to remember is that you need MegaCli to do the flashing. You also need the correct file,I tried at least 2 different Perc 6 firmwares from Dell that kept getting rejected as corrupt by MegaCli(they were really the wrong version). I have an external PCI-E Dell 6 Perc/I butI chose images from the 'Integrated" on motherboard version as it was allI could find. They are different, and below is my first time finding success.........
  • LSI MegaRAID Adventures, Guide and HowTo


    LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
  • openoffice calc printing extra blank pages


    Make sure that the Page mode is set to landscape and that the columns fall within the margins/boundaries, otherwise this is why there will be blank pages (Print Preview will show you this too).........
  • WD 20EARX Dead Again


    Another new drive bad from the start: Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........
  • WD 20EARX 2TB Bad within days


    This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad. ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0 ata1.00: irq_stat 0x40000008 ata1.00: failed command: READ FPDMA QUEUED ata1.00: cmd 60/00:00:........
  • Bad Hard Drive Slows Down Computer


    Here's a proven example of what a bad hard drive can do, it was technically functioning OKin a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application. The truth is that this failing 1TBHitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..). After swapping it out, tabs change instantly, emails are not lagged, and........
  • Hitachi Serial Numbers for Hard Drives without seeing the physical drive


    Here's what SMART tells me the serial number is: === START OF INFORMATION SECTION === Device Model: Hitachi HDS721010CLA332 Serial Number: JP2940HQ3ZY7KH Firmware Version: JP4OA3EA User Capacity: 1,000,204,886,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is:&nb........
  • Centos 6 RTL8111/8168B r8169 link up and down error solution/fix


    02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) For whatever reason it seems the r8169 driver that ships and has shipped with most Linux distros for years is still flawed and does not work properly on these cards, causing 100mbit connectivity when it should be 1gbit and even worse, causing random network dropouts. The r8169 driver in Linux kernels is simply not meant to be used on th........
  • Startech SV1107IPEXT KVM/IP Review


    Let's keep this simple, it's horrible, not only is the picture quality horrible (it's not a big deal) but the keyboard input is an issue. You have to type slowly, lightly and carefully otherwise 1-keystroke could end up being dozens of keystrokes. It's also a confusing unit for many datacenter techs, I've seen these units hooked up wrong and the instructions themselves aren't clear. I had to resort to shipping one to my office and take my phone pictures of the setup for th........
  • Lantronix KVM/IP Keyboard/Mouse not working in BIOS before booting the OS


    I've run into two issues with Lantronix based KVMs on various servers and here's how I solved them (with that said I like these units as they are Java based and OS independent and work very well, unike some other models like Startech). 1.) If you are connected by USB only and you're sure USB support from the BIOS is enabled, you just need to click the following in Lantronix Interfaces -> Keyboard/Mouse Check "Force USB Full Speed Mode", this fixed the issu........
  • Disable SELinux How To Tutorial Solution


    Here is a quick script that works on most Centos versions to disable the virus/SELinux from blocking basic functionality. The first echo 0 statement disables SELinux instantly but it will still be enabled on reboot. The second line disables it permanently. #!/bin/bash #disable SELinux Immediately echo 0 > /selinux/enforce #disable SELinux Permanently sed -i 's/SELINUX=enforcing/SELINUX=disabled/g' /etc/selinux/config........
  • Linux Ubuntu/Debian ATI 9902 No Sound Solution on HP G6 Pavilion Laptop


    00:14.2 Audio device: Advanced Micro Devices [AMD] Hudson Azalia Controller (rev 01) 00:01.1 Audio device: Advanced Micro Devices [AMD] nee ATI Device 9902 Backup your also.conf file cp /usr/share/alsa/alsa.conf /usr/share/alsa/alsa.conf.bk Change all instances of "card 0" to "card 1" (no need to manually do it, this command below does it all instantly and without fail or error:........
  • Linux Ubuntu Nvidia GT430 Lockups/Errors/Freezes NVRM: os_schedule: Attempted to yield the CPU while in atomic or interrupt context


    I'm running Ubuntu 10.10 with Asus NVIDIA GT430 2.6.35-32-generic-pae #65-Ubuntu SMP Tue Jan 24 14:06:16 UTC 2012 i686 GNU/Linux Nvidia binary driver: 260.19.06 The screen sometimes completely freezes and locks up or everything starts going very slow: [1903398.100007] NVRM: os_schedule: Attempted to yield the CPU while in atomic or interrupt context [1903402.373210] NVRM: Xid (0001:00): 53, CMDre 00000000 00000080 00000000 00000005 00........
  • File /etc/vz/conf/ve-vps.basic.conf-sample not found: No such file or directory - Openvz Error solution


    Stuff like this always happens/breaks after a vzctl update, whether it's new parameters being added or required etc.. File /etc/vz/conf/ve-vps.basic.conf-sample not found: No such file or directory Fix the value of CONFIGFILE in /etc/vz/vz.conf Creation of container private area failed Warning: distribution not specified in CT config, using defaults from /etc/vz/dists/default WARNING: /etc/vz/conf/4400.conf not found: No such file or directory........
  • How To Burn ISO Image using cdrtools/dvdrtools for Linux/Unix Ubuntu/Debian/RHEL/Centos etc..


    It really is as simple as: cdrecord -v dev=/dev/sr0 pathtoyourisoimage.iso -v is for verbose, I prefer it but if you don't you won't see as much output like below (I like to know the details and exactly what's happening) dev=/dev/sr0 specifies the device name of your burner (they say not to use it and to specify some weird annoying device string but using the raw /dev has always worked for me and is how it should have been implemented from the start IMHO)........
  • How To Test If Your Hard Drive Is Good/Signs of dying hard drive


    I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem: We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........
  • smart is not smart, it thinks a dead drive is still good


    I had a dying drive that smart thought until it totally disappeared was a good drive, and actually all parameters did look fine but this system was causing my system to lockup and other bad behavior: === START OF INFORMATION SECTION === Device Model: WDC WD20EARS-00MVWB0 Serial Number: WD-WMAZ20139 Firmware Version: 50.0AB50 User Capacity: 2,000,398,934,016 bytes Device........
  • Hitachi 2TB HDS5C3020ALA632 drive DOA


    I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead): ata1: link is slow to respond, please be patient (ready=0) ata1: softreset failed (device not ready) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: link online but device misclassified, retrying ata1: link is slow to respond, please be patient (ready=0) ata1: softreset f........
  • pgina can't login after installing


    After Installing pgina I couldn't login to Windows anymore with my blank password Administrator account! An unknown error has prevented your account from being created.nrThis may be due to policy or security settings as well as other machine configuration.nrPlease consult your administrator. Hit F8 to start Windows in Safe Mode and you can login normally and then remove PGina, it shouldn't cause this problem or behavior out of the box.........
  • Santrex Review Scam Complaint - Stole My Money Fraud


    Santrex Review/Scam/Complaint Santrex never provided any working server, I believe it was just a dummy management Solus server because the server said it was booted but never connected to the console. I complained to them and eventually the support admitted the server was not working and to wait for 24 hours. I waited for 4-days, after which they sent an e-mail saying my service was being disabled for SPAM ...(when SolusVM shows 0kb of traffic). Th........
  • Virpus Review/Scam/Complaint


    Virpus Review/Scam/Complaint Virpus is advertised on LEB (lowendbox.com). My initial payment was refunded after days of not receiving the VPS, but two subscrption payments went through and Ionly received notification after the second one. They ignored the requests in the ticket and by e-mail for a refund and even escalated the PayPal dispute that "we're assuming this is for a service that was provided" (when they obviously know otherwise by........
  • Linux - mptbase/MPT Fusion LSI Logic Error mptbase: ioc0: ERROR - didn't initialize properly! (-1)


    kernel 2.6.27.54 Fusion MPT base driver 3.04.07 Copyright (c) 1999-2008 LSI Corporation Fusion MPT SPI Host driver 3.04.07 mptbase: ioc0: Initiating bringup mptbase: ioc0: WARNING - Unexpected doorbell active! mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000001! mptbase: ioc0: ERROR - Diagnostic reset FAILED! (102h) mptbase: ioc0: WARNING - NOT READY! mptbase: ioc0: ERROR - didn't initialize proper........
  • VPS Server Scam/Review/Complaint List


    These are the only two I've encountered but here is the low-end and note my story is not at all unique. In my case I was scammed out of money and did not receive any service at all from either company. Santrex Review/Scam/Complaint Santrex never provided any working server, I believe it was just a dummy management Solus server because the server said it was booted but never connected to the console. I complained to them and eventually the support adm........
  • Enable SPAMASSASSIN on Postfix in 5 minutes


    Centos 5 Postfix and SPAMASSASSIN Tutorial yum install spamassassin chkconfig spamassassin on vi /etc/mail/spamassassin/local.cf ############## #required_hits 5 #report_safe 0 #rewrite_header Subject [SPAM] #5 is the least restrictive (means only the most obvious SPAM is caught. 0 is obviously the most restrictive/sensitive and would have lots of false positives require........
  • Toms Hardware Hard Drive Comparison/Hitachi Deskstar 1TB


    I bought the 1TB Deskstar C revision recently at just $49 each and put them in RAID 1for my Desktop. Look at how close the old Deskstar 1TB comes to matching the performance of the mor expensive Samsung and WD's? This is phenomal, I can't believe the performance I've gotten out of these cheap drives. http://www.tomshardware.com/reviews/hitachi-western-digital-terabyte,2017-6.html........
  • named/bind cannot find zone file, load zone files without specifying full directory path/loading master file genuine.com.zone: file not found


    genuine.com/IN: loading master file genuine.com.zone: file not found _default/genuine.com/IN: file not found I always found it silly that no one really talks about this and apparently many like me and even control panels like Plesk were still using hard paths. I always thought "why can't I just specify the name of the zone file and have bind find it". Surely the default search path must be /var/named or somewhere else but there is no such thing.........
  • md: data-check of RAID array md3


    This really made me nervous but notice the mdstat says "check". This is because in Ubuntu there is a scheduled mdadm cronscript that runs everyday on Sunday at 00:57 that checks your entire array. This is a good way because it prevents gradual but unnoticed data corruption which Inever thought of. As long as the check completes properly you have peace of mind knowing that your data integretiy is assured and that your hard drives are functioning properly (I'........
  • Ubuntu/Debian DRBD 8.0 Setup Guide


    I've only used it on Centos, soI thought I'd make a quick Debian guide: Install the DRBD Package apt-get install drbd8-utils Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: libswfdec-0.8-0 Use 'apt-get autoremove' to remove them. The following........
  • WD (Western Digital) Advanced Format Drive Lagged/Slow Speed/Performance/Design Flaw EAD/EARS problem WDC WD20EARS-00S8B1


    Let the numbers speak for themselves, from what I read the Load_Cycle_Count which is very high (more than 500,000/half a million times) is the number of head parks. What a stupid"Green" design and design flaw which will probably mean an early life for the drive. This is almost as silly as Seagate's new reputation for BSY/poor quality disks since the 7200.11 series. To make it worse this is also when Western Digital introduced "Advanced Format" o........
  • Wine stopped working/won't work Solution


    After an upgrade wine wouldn't open anything, not even the pre-installed notepad. There are no wine logs and nothing is mentioned in any standard log file about why. I finally decided to run wine from the shell and see what's going on: wine client error:0: version mismatch 398/402. Your wineserver binary was not upgraded correctly, or you have an older one somewhere in your PATH. Or maybe the wrong wineserver is still running?........
  • Revert to GRUB 0.97/1 instead of GRUB2


    had trouble trying to revert Ubuntu 10.04 LTS from grub2, won't boot mdraid and did not even install mdadm during the installation! I have tried moving back to GRUB 0.97 backed up original /boot and then copied /boot from an old Debian install. Modified device.map and menu.lst and put the appropriate kernels and initrd for Ubuntu back in /boot I ran grub: root (hd0,1) grub> setup (hd0) Checking if "/boot/grub/stage1........
  • Linux Burn MP3 CD On the Fly using


    I finally decided to look into some utils that did this, and the first one I found is "mp3burn". It is unbelievable simple and perfect. *2017-11 update and mp3burn is still available in standard repos such as Ubuntu 14/16 so this is a current and working project. Just install the package and it gets all required libraries to convert and then burn's on the fly. And you won't believe how simple it is. I just want to a directory that had the MP3's I wanted t........
  • FUSE/Curlftpfs mount ftp account as drive partition in Linux


    This is a great way to use your ftp server space, for example on your web hosting account (althoughI believe many hosts don't allow storage like this), but if you have a VPS/Dedicated Server etc.., this would be perfect. Imagine how easy it is to work with an ftp account that you can just mount as a normal partition or directory in Linux, it would be great for backups etc.. Name curlftpfs - mount a ftp host as a local directory Synopsis........
  • Use rcconf to edit startup/init.d/init scripts on Debian/Ubuntu based distributions


    I've never understood how to enable and disable services for different run levels in Debian based distros, it's just weird, annoying and doesn't make sense. I much prefer chkconfig from RHEL. Just install the package called 'rcconf' and be done with it. rcconf makes things easy for you. apt-get install rcconf Reading package lists... Done Building dependency tree Reading state information... Done........
  • Unixbench Score on Core i5 750 with OpenVZ Kernel vs Xen/Openvz


    This was unbelievable how much the Xen kernel slows things down, keep in mind both tests were done on the hostnode, one was with the Openvz-Xen hybrid kernel and the other was just OpenVZ. You can see the performance difference is nearly 300% better when not using the Xen kernel. OpenVZ-Xen Kernel Test Results (I was wondering what was wrong/so slow with my Core i5!) # # # # # #&n........
  • Seagate Drive 500GB Drive Dying


    This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device........
  • Seagate 7200.11 firmware defect in 500GB, 1000GB (1TB) and 1500GB (1.5TB) Hard Drives


    Seagate Inventory/Firmware Check I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate. *Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate! Seagate Inventory/Firm........
  • Linux EXT3 16GB-17GB maximum filesize issue solved/how to fix


    I have no idea why but mkfs.ext3 defaults to a patheticlly small blocksize of 1024 bytes/1KB (kilobyte). That means the maximum filesize is ONLY 16GB! With 2KB/2048 bytes you get a 256 GB maximum filesize, and with 4KB/4096 bytes you get 2TB! I finally noticed/paid attention to this after realizing that with rsync and scp that no file larger than 17GB could be transferred. I then realized it must be a file size limit on the partition. Here is what tune2fs tol........
  • XMPP Chat Protocol using Jabber - Guide Tutorial Setup Linux Chat Server


    In Debian based distros: apt-get install jabber Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: fakeroot dkms Use 'apt-get autoremove' to remove them. The following extra packages will be installed: jabber-common The following NEW packag........
  • Picking an FTPD (vsftpd) Server in Linux Centos/Debian


    I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find. yum search ftp Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * rpmforge: ftp-stud.fht-esslingen.de * base: mirrors.netdna.com * updates: updates.interworx.info * addons: yum.singlehop.com * extras: mirrors.netdna.com rpmforge........
  • Compaq V2405CA Laptop - Unixbench Performance Test


    Here are the results, it is Sempron 3000+ AMD Mobile, 500Gig HDD, 512MB RAM with shared ATI Radeon graphics. # # # # # # # ##### ###### # # #### # # # # ## # # # #&nb........
  • PHP cannot access /usr/bin/openssl


    PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist: [code:1:1fd0f3abbe] if (!file_exists($OPENSSL)) { //echo "ERROR: OPENSSL $OPENSSL not foundn"; }[/code:1:1fd0f3abbe] I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........
  • Mysqld Solution - Can't init databases /usr/libexec/mysqld: Can't read dir of '/tmp/' (Errcode: 13) /usr/libexec/mysqld: Can't create/write to file '/tmp/ibyP1qUC' (Errcode: 13) 100215 7:02:24 InnoDB: Error: unable to create temporary file; errno


    100215 07:02:24 mysqld started /usr/libexec/mysqld: Can't read dir of '/tmp/' (Errcode: 13) /usr/libexec/mysqld: Can't create/write to file '/tmp/ibyP1qUC' (Errcode: 13) 100215 7:02:24 InnoDB: Error: unable to create temporary file; errno: 13 100215 7:02:24 [ERROR] Can't init databases 100215 7:02:24 [ERROR] Aborting 100215 7:02:24 [Note] /usr/libexec/mysqld: Shutdown complete 100215 07:02:........
  • Unixbench Score with Glusterfs/Openvz & Quad Core Xeon - Updated with GlusterFS 2.0.8


    You might remember my original GluserFS/OpenVZ benchmark which produced a horrible 29.8 This is the exact same system, but using the latest 2.0.8 (with some small files patch which speeds up performance) you can see it is about 25% faster. I also haven't tuned my config files at all, but there are some settings that should increase performance on small files which I believe i........
  • Unixbench Score with Glusterfs/Openvz & Quad Core Xeon


    This is very disappointing since GlusterFS markets itself as a solution to deploy VPS servers on. On the HNitself I get a Unixbench of about 360. I'm also using an SSH tunnel to secure the communications, but even before that, things seemed very slow. # # # # # # # #####&n........
  • MySQL Restoring And Dumping/Backing UP MySQL Data/Tables/Databases


    Backing MySQL Databases Backing Up/Dumping All Mysql Databases To A Single File mysqldump --all-databases -u admin -p > allmysqldatabases.sql The "-all-databases" clause is pretty obvious isn't it? It means that it will backup all databases. The "-u admin" means login using the user "admin", if you h........
  • iPhone 3GS 32GB "Harsh Review"


    Yes, Iadmit I finally got bitten by the hype as much as I can usually see through it all. Keep in mind this review is of the "stock" phone, no jailbreaking yet which is what really unleashes the customizability and whyI bought iPhone. I had better things to say about this phone before buying it, and it is a great phone, perhaps the best on the market by far, if not because of the Mac OS port onto the iPhone and all the apps, etc, etc. With that said........
  • Apple iPhone 3GS and predecessors are leading a revolution


    As much of a computer nerd as Iam, I'm usually a late adopter to technology for a few reasons. Ifeel most new hyped technologies and electronics are mainly fads, and I'm also cheap. Adopting later means you avoid the bugs, kinks and most importantly pay the lowest price, that's me being cheap again :) I never read much about the iPhone but Isaw all the hype around it and until recently I wasn't a big fan of anything Apple until a few years ago I realize........
  • Nokia N97 review, feedback and complaints


    I've had an old Blackberry for a few years and I was ready to spend some serious cash on a nice Nokia. I love the idea of the Linux based Symbian S60 OS, so I was looking at phones like the E63, E71 (both are basically the same, at least CPU/screensize although E71 is thinner, has a 3MP camera, has GPS, and has dedicated buttons to adjust the volume). Then Iheard about the N97 and what a revolution it was supposed to be and it was even compared to iPhone. To........
  • RTL8111/8168B R8169 Gigabit Link slow speeds


    This is the Intel Atom 330 motherboard with integrated Realtek Gigabit NIC (Intel Desktop Board D945GCLF2 Motherboard W/ Atom 330 1.6 GHz Dual Core Processor - Mini-ITX) I cannot achieve more than 15 MB/s, even doing a local transfer through eth0 to it's own IP. 100% 95MB 15.9MB/s 00:06 So this is not a cabling, switch or hardware issue, it seems like a driver or chipset limitation problem. Here is my........
  • Latest Articles

  • ImageMagick Convert PDF Not Authorized
  • ImageMagick Converted PDF to JPEG some files have a black background solution
  • Linux Mint Mate Customize the Lock screen messages and hide username and real name
  • Ubuntu/Gnome/Mint/Centos How To Take a partial screenshot
  • ssh how to verify your host key / avoid MIM attacks
  • Cisco IP Phone CP-8845 8800/8900 Series How To Reset To Factory Settings Instructions
  • ls how to list ONLY directories
  • How to encrypt your SSH private key file id_rsa
  • Linux Mint 18 Disable User Name List from showing on Login Screen
  • Firefox Cannot Hit Enter Key In Address Bar and Location History Not Working
  • Cisco Unified Communications Manager / CUCM IP 8.6,10,12 Install Error Solution
  • Ubuntu Debian Mint Linux SSHD OpenSSH Server Not Starting After Reboot Solution
  • nmap how to scan for all ports and not just the 1000 most common ports
  • Windows 7,8,10 and Server 2008, 2012, 2016, 2019 Read Only Attribute Won't Go Away
  • bind / named how to make a wildcard record and retain defined A records
  • Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM
  • Local Vs Universally Administered MAC Address NIC Refuses to come up
  • Cisco Unified Communications Manager 12 CUCM 12 - How To Enable Video Calling
  • Windows 7, 8, 10, Windows Server 2008, 2012, 2016, 2019 How To AC97 Audio Drivers and Other Unsigned Drivers
  • Cisco Unified Communications Manager / CUCM IP Telephony Definitions