Docker Container Onboot Policy - How to make sure a container is always running

Generally most containers are by default set not to start automatically. Ther eare 3 settings for the "RestartPolicy" of containers: No: Do not automatically restart the container (default). Always: Always restart the container regardless of the exit status. Unless-stopped: Always restart the container unless it is explicitly stopped. On-failure:........

How to Install Any OS on a Physical Drive from Windows Using VMware Workstation (Linux, Windows, BSD)

Uses: Install OS on physical drive Linux installation VMware Install Windows on physical drive Boot OS from physical drive VMware Workstation tutorial Linux virtual machine to physical disk Windows to Linux migration Dual boot OS installation Boot from external SSD Linux, Windows, BSD installation guide Physical drive boot OS........

How to resize a pdf without losing much quality in Linux Mint Ubuntu Debian Redhat Solution

Do you have a PDF that was too large after merging using convert / ImageMagick? Use gs or ghostscript as below, specify the output file and also the input file. In the example below the output file is "outputfile-resized.pdf" and the input file is "original-pdf.pdf". Change the input file to the name of your pdf gs -sDEVICE=pdfwrite -dCompatibilityLevel=1.4 -dPDFSETTINGS=/prepress -dNOPAUSE -dQUIET -dBATCH -sOutputFile=outputfile........

hostapd example configuration for high speed AC on 5GHz using WPA2

This example is using RTL8821AU chipset from a TP-Link T2U Plus USB adapter and other similar ones should work the same. Here's how to get this chipset RTL8821AU working in Linux. Here's how to get RTL8812 and RTL8822 working in Linux.........

isc-dhcp-server dhcpd how to get longer lease

You can do a static lease that is tied to the MAC address but what a lot of users prefer is that they come into the office or lab the next day and that their device gets assigned the same IP address (if possible). As we can see in the dhcpd logs that there is threshold that is defaulted as we'll show later. Whatever the threshold is set at, if the lease is younger than the threshold, it will keep the same lease. In other words, if the device goes to sleep or is powered off........

How to Reset CIPC Cisco IP Communicator for CME CUCM CallManager

Just hit **# on the keypad and the CIPCwill enable the button in settings for a factory reset. Sometimes the phone may run into issues or may be unable to register to another tftp server (eg. another CME or CUCM server) due to a bug or maybe due to the security settings tying it to a specific server. Step 1 - Click Settings Step 2 - Hit "**#"........

Internet Explorer Cannot Download File "Your security settings do not allow for this file to be downloaded." Security Settings Solution

By default in most newer Windows installs, you will not be able to download files from "Internet" sites and you'll get this error "Your security settings do not allow for this file to be downloaded." Solution to Enable Downloads in IE Internet Explorer 1.) Go to Settings (button) -> Internet options -> Security (tab) 2.) Click "Internet" and then the "Custom Level" button. 3.) Find the following section and set D........

How to install and configure haproxy on Linux Ubuntu Debian

haproxy is one of the best known and widely used Open Source load balancers out there and a strong competitor to nginx. haproxy is used by many large sites per Wikipedia: HAProxy is used by a number of high-profile websites including GoDaddy, GitHub,........

Dell PowerEdge Server iDRAC Remote KVM/IP Default Username, Password Reset and Login Information Solution

Are you new to the company, datacenter or a third party who is responsible for deploying a fleet of servers from scratch. The first step is to normally login to the KVM so you can perhaps manually reinstall, PXE boot the Cloud Image or reimage/reinstall an OS but you need access to the KVM/IP or what Dell calls iDRAC. It's common that you may have forgotten this information or that another employee or colleague has changed the info and did not tell you, that they have left the........

Thunderbird Attachment Download Error Corrupt Wrong filesize of 29 or 27 bytes Solution

This is an ongoing issue even with the latest Thunderbird 102.x where attachments downloaded via IMAP just won't save or will be corrupt which is a huge interruption to workflow or if you come back later to find out the file you thought you saved is invalid/corrupt and you have perhaps deleted the e-mail. How to solve the Thunderbird filesize attachment issue? 1. Click on "Settings". then go to "General". 2. Scroll to the bottom to find "Conf........

Generic IP Camera LAN Default IP Settings DVR

If you are converting a generic wifi IP camera to ethernet, it may not be that simple as many are default hard coded to a static IP of 192.168.1.168 and login info admin/admin. From there you can login to the camera and assign it to DHCP by going to http://192.168.1.168 For security these cameras +DVR should be on a separate untagged VLAN or if possible a physically isolated non-internet connected switch/network. The reference below is applicable to many of the r........

Cisco Switch / Router How To Restore Factory Default Settings

1.) Make sure your conf register is 0x2102 Do show version and at the very end of the output you will see the Configuration register. show version Configuration register is 0x2102 If the config register is not 0x2102 then enter this command: r1#configure terminal r1(config)#config-register 0x2102 r1(config)#end 2.) Let's Erase the NVRAM/flash........

How To Do Linux Network Bonding Teaming in Mint Debian Ubuntu

Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........

Ubuntu Linux Mint - Volume Control Stopped Working

Volume control will often stop working, if your sound server (normally pulseaudio) dies or restarts whether by itself or by you. The reason pulseaudio may need to be restarted is due to some sort of crash or other issue that prevents sound from working (normally restarting or doing a killall pulseaudio fixes things). However, you will normally find at least in OS's like Ubuntu/Mint 16/18+ that you cannot control the volume whether adjusting the level, changing input/outputs and........

How to install Kubernetes with microk8s and deploy apps on Debian/Mint/Ubuntu Linux

Kubernetes Easy Beginners Tutorial/Architecture Guide Kubernetes is known as container orchestration and we should start at explaining the container part of it. A Container is what runs the actual application and based on an Image, and are more comparable to something like an LXC Container, Virtuozzo/OpenVZ using the Linux Kernel Namespaces feature. Containers run these images as independent, isolated operating environments under the O........

Juniper JunOS Command Overview and Howtos Switch, Router, Firewall Tutorial Guide

Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........

Nvidia Ubuntu Linux Screentearing Video with solution driver

This seems to happen on most if not all Nvidia cards but the good news is that if you are using any of the Linux drivers and have the nvidia-settings tool installed it is just a simple command. Solution: nvidia-settings --assign CurrentMetaMode="nvidia-auto-select +0+0 { ForceFullCompositionPipeline = On }" Enter the above command in your terminal and the screentearing will be fixed which is like enabling Tear Free on AMD cards.&........

How To Speed Up Linux Ubuntu and Debian Based Computers By Improving CPU Performance and Changing the CPU Governor

I used to believe that for Desktops especially that the "ondemand" CPUfrequency changing that kernels included with Ubuntu and Debian based distros have would be sufficient for snappy performance. However, you can feel the lack of performance on the fastest computer if you have ondemand. A lot of times even under high load 100% of your CPUfrequency in MHz will not be used. For example a 2.8Ghz CPUmay only run at 1.8MHz or even .9GHz. Now........

SSH and sshfs timeout settings keepalive

A big problem over ssh and especially sshfs is that your connection will often timeout and disconnect after inactivity. To fix this you can modify the server but it may not be practical or you may not have access. Why not send keep alives fom your end (client side)? Just edit /etc/ssh/ssh_config (not to be confused with sshd_config as that is the server side): Find the line that says "Host *" and change it like this:........

Debian and Netplan

Create your netplan file vi /etc/netplan/01-netcfg.yaml network: version: 2 renderer: networkd ethernets: ens3: dhcp4: no ........

how to use ifplugd in Linux to execute a command or script when a NIC cable is unplugged or plugged in

It is fairly simple to use once you know how to use it. However, the tricky thing is that by default it doesn't seem to be active or listen on any interface on manually specified. How To Install ifplugd First we install ifplugd sudo apt install ifplugd Let's enable it on our desired device(s) vi /etc/default/ifplugd set this line as so:........

Ubuntu Linux Mint Debian xorg performance and tear-free tuning for AMD Radeon Based Cards

I find that the default settings for the radeon driver that is applied to most AMD cards is horrible. For example by default TearFree is not enabled and it causes videos to have some kind of square artifacts. Here are the settings I have found most suitable for AMD cards: You need to create file in the following path and restart Xorg or your computer to apply it: *Beware that making a mistake here will possibly make your computer........

CentOS 6 and 7 / RHEL Persistent DHCP Solution

It is very silly but the default on the ifup-eth script tells dhclient ( the program that obtains a DHCP IPaddress if you have selected DHCPin your ifcfg-eth* config file) to EXIT / QUIT if the first attempt to obtain a lease fails. No amount of dhclient.conf settings will fix this because if dhclient is started with -1 (which it is by default)then dhclient will quit. This is obviously very bad for MOST cases. Say for example you have a power outage or........

python import docx error

sudo pip3 install python-docx [sudo] password for : Downloading/unpacking python-docx Downloading python-docx-0.8.10.tar.gz (5.5MB): 5.5MB downloaded Running setup.py (path:/tmp/pip_build_root/python-docx/setup.py) egg_info for package python-docx no previously-included directories found matching 'docs/.build' warning: no previously-included files matching '.DS_Store' foun........

Linux Mint How To Set Desktop Background Image From Bash Prompt CLI

The way of doing it in mint is different than gnome and ubuntu. gsettings set org.mate.background picture-filename /path/to/file.jpg *If you try to use the gnome way it will NOT work with Linux Mint: gsettings set org.gnome.desktop.background picture-uri /some/pic.jpg........

Ubuntu/Gnome/Mint/Centos How To Take a partial screenshot

By default printscreen or alt print screen will get the whole desktop or the application in focus, respectively. But what if you want to select a portion of the screen? gnome-screenshot: ksnapshot compiz This is a nicely integrated solution sudo apt-get install compizconfig-s........

Cisco IP Phone How To Reset To Factory Settings Instructions CP 9971, 8800, 8900, 8845, 8851, 8841, 8831, 7961, 7960, 7945, 7942, 7941, 7940.

This would be crucial especially if the phone is hardened, not being able to reset or change settings could prevent a phone registering in a new environment or even when migrating from office to office. This applies even if you are trying to migrate the phone to another platform such as Asterisk/FreePBX etc... This guide applies to nearly all of the Cisco IP phones that you would use in CME or CUCM from several years ago including models: 9900, 9971, 8800, 8900, 8845, 8851, 8841........

Cisco Unified Communications Manager / CUCM IP 8.6,10,12 Install Error Solution

Install Errors on Version 12: This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5 on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error. *Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install. What really causes this even though you successfully install........

Cisco Unified Communications Manager 12 CUCM 12 - How To Enable Video Calling

There are multiple layers but most are enabled by default such as the setting in the Phone Device Settings. However the one not enabled by default is the one in "Enterprise Phone Configuration". Enable "Cisco Camera" and then reboot your phones to enable it.........

Windows 7, 8, 10, Windows Server 2008, 2012, 2016, 2019 How To AC97 Audio Drivers and Other Unsigned Drivers

Oops did you get this error trying to install an oldschool driver and think it is hopeless in a new version of Windows? First of all it is almost never a program compatibility issue: ........

X11 SSH Linux Forwarding Error

Jan 30 17:16:10 localhost sshd[25385]: error: Failed to allocate internet-domain X11 display socket. The solution for me on the server side was the following in sshd_config: AddressFamily inet *Remember to restart sshd and also reconnect from the client side. Ihad all the normal X11 settings on the server but it just stopped........

Using Microsoft's Group Policy Management Editor (GPME) To Change Default Permissions and Internet Explorer Security Settings

The defaults in Windows 2016 server leave clients crippled so they can't even download basic files or software. But Group Policy Management Editor comes to our rescue! Use cmd or Powershell and run: gpme.msc Choose your domain/computer and then navigate like below and create a new menu entry for IE11 or whatever your version is. Don't be worried if the highest version is IE10 it means that it applies to IE10 AND above.........

Thunderbird How To Disable An Email Account

Navigate to Tools -> Account Settings -> Server Settings Uncheck the following: "Check for new messages on startup" "Check for new messages every NN minutes" "Automatically download new messages". Source: http://forums.mozillazine.org/viewtopic.php?t=635510........

/etc/iproute2/rt_tables default settings file in Linux Centos 6,7 and most other NIX's

This should apply to most Linux distributions just incase you get into trouble or wipe out the defaults by accident. /etc/iproute2/rt_tables # # reserved values # 255 local 254 main 253 default 0 unspec # # local # #1 inr.ruhep........

How To Edit Linux Based NM Network Manager Connection Settings Without GUI

Just find the relevant file in /etc/NetworkManager/system-connections sudo vi /etc/NetworkManager/system-connections/Wired connection 1 [802-3-ethernet] duplex=full mac-address=00:00:00:FE:FE:FE [connection] id=Wired connection 1 type=802-3-ethernet timestamp=1532403341 [ipv6] method=ignore [ipv4] method=manual........

Linux Disable IPV6 Centos / Debian / Mint Howto

Set this in /etc/sysctl.conf net.ipv6.conf.all.disable_ipv6 = 1 #apply the settings sudo sysctl -p ........

Linux use growisofs to burn a larger file on a BD-R / Bluray Disc

growisofs -Z /dev/sr0 critical.tar.gz.gpg Executing 'genisoimage critical.tar.gz.gpg | builtin_dd of=/dev/sr0 obs=32k seek=0' I: -input-charset not specified, using utf-8 (detected in locale settings) File critical.tar.gz.gpg is larger than 4GiB-1. -allow-limited-size was not specified. There is no way do represent this file size. Aborting. :-( write failed: Input/output error #remember to us........

Debian Linux Mint Ubuntu iptables save and restore settings automatically onboot and reboot

First you need the "iptables-persistent" package. This gives you an init script that loads your settings from /etc/iptables/rules.v4 and rules.v6 When you install it, it wll save your default setings in /etc/iptables. sudo apt-get install iptables-persistent Remember that the rules are stored here: For IPV4: /etc/iptables/rules.v4 For IPV6: /etc/iptables/r........

Linux What is umask (user mask) for file and directory creation permissions and how to calculate umask and change the defaults

umask are the default permissions that are applied when a file or directory are created. To see this in action simply just "touch filename" or "mkdir somedir" and you'll see what default permissions are applied. The first thing Ialways tell people you should know is to NEVER change the defaults unless you are making them more restrictive. But they work well and if you change the defaults you could end up creating a file without permission to read........

AMD Set Fan Speed and Other Powerplay Memory/CPU Timings with a Linux script

You can do other things but this particular script is just to set all AMD cards to 80% fan speed (remember this script needs to applied everytime you reboot). You could set it is a cron or just throw it into /etc/rc.local basepath=/sys/class/drm for hwmon in `ls -1 /sys/class/drm|grep card[0-99]$`; do echo card=$hwmon; hwmonname=`ls $basepath/$hwmon/device/hwmon|grep hwmon[0-99]` hwmonpath=$basepath/$hwmon/device/hwmon/$hwmonname echo "ec........

genisoimage errors with long filenames and deep directory structures

You'll have to violate the iso9660 standards but it is necessary if you want to preserve your filesystem and filenames and shouldn't be an issue as long as you are using a modern OS like Linux. genisoimage -o Backup-Myfiles.iso -r -J -joliet-long /some/path/ You will get errors like below (even enabling joliet-long didn't help) genisoimage: Error: /some/filename.pdf have the same Joliet name Joliet tree sort failed. The -joliet-lo........

Supermicro IPMI / KVM / BMC Remote Console Screen Resizing Issue - Window Cut Off Solution

It could just be my specific Java but other KVM/IP works ok on my machine but with Supermicro's IPMI for some reason the console window doesn't resize and even putting it in full screen leaves the window cut off as shown below: As you can see above the screen is cut off you can't see the "Iagree" on the right side. The window resi........

VMWare Vsphere VCSA Graphical Install Creates json

yes it does create its own json ============================================ cat /tmp/vcsaUiInstaller/ovftool-20180809-175238948-20180809-175603497.log |grep -i json 2018-08-09T17:56:04.238-07:00 verbose OVFTool[30966] [Originator@6876 sub=Default] Manifest file entry: SHA1(VMware-vCenter-Server-Appliance-6.7.0.12000-8832884_OVF10-file1.json) = 1deb658c724767697587d5909c4051c01813e6a1 --> ........

Debian Mint Ubuntu compiling xmr-stak

sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........

PayPal IPN Failed "result: IPN Handshake Invalid"

This is often the result of PayPal's "item name" or another name having invalid characters or not supporting Unicode. 173.0.81.1 - - [17/Jul/2018:13:39:45 -0400] "POST //modules/gateways/callback/paypal.php HTTP/1.1" 406 - "-" "PayPal IPN ( https://www.paypal.com/ipn )" A good clue is if you check the debug output of the IPNand find a mandatory column empty. ........

VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI

#mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........

Linux Mint Black Screen after boot no graphics solution

This is not the normal "black screen"issue and I was shocked to eventually find out why. The normal advice of reconfiguring Xorg didn't work. Even booting into "Recovery Mode" did not help. Here is the short end of the stick that fixed it: sudo apt-get install mdm mate-desktop-environment Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled. This must be whe........

Intel NUC J3455 Linux Kernel freeze slowness 4.4.98 errors

It looks like this has something to do with APIC but I am not sure. I have similar CPUs with a different MB and BIOS that work fine on the same type of kernel. A lot of time the issue is because of the C-step setting in the BIOS. The same thing happened on the 2.6 kernel with Centos 6 but this is a homebrew 4.4 kernel soI am not sure why it is happening when even Centos 7 (3.2) kernel works OK. Solution - It comes down to the BIOS set........

IcedTea Java Web Viewer Config Utility How To Enter

In at least Ubuntu and Mint there is nothing intuitive about configuring Java. Execute it to get to it: itweb-settings You'll be able to configure different options and variables. You can also check under Security as some of those settings could prevent applets from starting or prompting to........

SMF Forums / Simple Machines Forums Not Displaying Images Theme or Styles Properly using 127.0.0.1

This is one thing that has me wondering about SMF. It is apparently a known issue but in the latest version and new install nothing looked right because it was using http://127.0.0.1 to find everything! How on earth would it ever do this or think it is normal? Excerpt of crazy html code it produces that causes the issue: ........

Linux How To Clone One System Harddrive to another remote system

The easiest way is to use SSHand DD or a combination of netcat. SSHwill be a little slower due to encryption but is the most secure way (on two older systems the average clone speed is about 40-50MB/s). This is also OS independent as it doesn't matter what the source OS is because you are literallly cloning the drive so you retain the partition table and settings. Clone HDD using SSH and DD........

tftp: client does not accept options - solution if you are using UEFI PXEBoot disable it!

tftp: client does not accept options I spent the good portion of a late evening on this double checking settings that I know always worked right for tftp! This error can also happen if you are trying to boot PXE in UEFImode. Enter your BIOS and change it to "Legacy PXE" or non-UEFI PXE mode and you'll be good to go!........

ffmpeg trouble concatenating similar but different files

When things go wrong your video is basically unplayable or the first video plays fine and then freezes when moving on to the next. Generally if both videos weren't produced with the exact 100% same settings you will have issues. You can try the basic concat but it often won't work right. Solution for me: My example uses 3 videos in total so "n=3" and a=1 to include audio. ffmpeg -threads 12 -i file1.mp4 -........

Nvidia Linux Mint/Ubuntu screentearing horizontal line solution

Finally after ages I found the solution which is on many pages on the net but not obvious and should have been standard or more common info! Instant Solution: Type this into the terminal (unfortunately the driver config menu doesn't have the option as itis hidden): nvidia-settings --assign CurrentMetaMode="nvidia-auto-select +0+0 { ForceCompositionPipeline = On }" Make permanent Cli........

check if Apache uses worker MPM or prefork MPM

apachectl -l Compiled in modules: core.c prefork.c http_core.c mod_so.c It is "prefork.c" so in httpd.conf these settings are what you would use (if you use worker.c it won't have any impact): StartServers 2 MinSpareServers 5 MaxSpareServers&nb........

Avocent DSR8020 KVM/IP - Network Connect Error - Solution

This error is commonly due to Java security or TLS settings but there is a second issue with forwarded ports that also causes it. 1. Java Security/TLS Settings issue: This article has the solution to change them all in Linux automatically 2. Port Forwarding Issue if your Avocent DSR is behind NAT/private IP........

ENOM TRANSFER passwords do not match - solution

The "passwords do not match" implies or makes it appear that your auth code is wrong but actually you have to click "View additional settings" and then see there are 2 password fields to manage the domain once it is transferred (the password is typed twice for confirmation). Simply fill out a password twice or remove the first password fields contents and all will be well.........

How to Properly Secure SSL/TLS Apache Settings against Heartbleed Poodle (TLS) Poodle (SSLv3) FREAK BEAST CRIME

Many users still are not aware but simply patching OpenSSL does not secure you against many known and easy to exploit attacks that will render your encryption useless by an attacker. Use the following setings in /etc/httpd/conf.d/ssl.conf SSLCipherSuite "EECDH+ECDSA+AESGCM EECDH+aRSA+AESGCM EECDH+ECDSA+SHA384 EECDH+ECDSA+SHA256 EECDH+aRSA+SHA384 EECDH+aRSA+SHA256 EECDH EDH+aRSA !CAMELLIA !SEED !3DES !RC4 !aNULL !eNULL !LOW !MD5 !EXP !PSK !........

K9 Mail Android Cannot See or View E-mails Disappear after reading - with Dovecot server. Solution

This actually only happened after an e-mail server ran out of space due to run away log files. Normal Desktop clients were not affected. It appeared to be a bug in K9 mail but even reinstalling/wiping all settings did not fix it (read e-mails would still not reappear). This is moreso a bug in Dovecot where it probably messes up the index files. How do you fix this in Dovecot/your e-mail server? You need to delete the do........

DRBD Slow Performance - 99.99 % [jbd2/drbd0-8] highiowait solution

Tired of checking iotop and seeing that your drbd partition is using 99.99% of io all the time and finding your drbd device performs slow in general? This is especially an issue in versions of DRBD in the 8.3 tree in particular one documented case is on "8.3.13" but it likely applies to other devices. The symptoms are that resyncing is fine and normal but any reasonable amount of activity is very slow and lagged and creates a high server load and con........

Avocent 8020 KVM Java Icedtea Viewer

This command in Debian/Ubuntu/Mint will get everything need installed for most Java based KVM viewers: sudo apt install icedtea-netx The following additional packages will be installed: ca-certificates-java icedtea-netx-common openjdk-8-jre openjdk-8-jre-headless It seems every other updated version of Java or Icedtea breaks things and I will save the frustration of Java for another post.........

unfortunately lg keyboard has stopped - LG Phone Keyboard Issue

This seems to effect many other LG phones , specifically their keyboard app and basically makes your phone unusable where you cannot use the keyboard because that message keeps popping up and the keyboard will not load. unfortunately lg keyboard has stopped solution: 1. Go to your settings and manage apps and find the LG Keyboard app: 2. Stop it from running, delete all data and clear all cache. After the above you will probably find that your........

Virtualbox errors on Ubuntu/Debian/Mint

The solution was to reinstall the vbox dkms package and do a manual modprobe of the modules it makes. I never sorted out the unable to start due to the USB issue, I did have the guest additions installed but the only way to boot was to change the pointing device from USB to PS2 and then to disable the USB controller (if your pointing device is set as USB, disabling USB will not work because it will re-enable by default when it sees your pointing device is USB, this is w........

HP Procurve Switch 2824 CLI Telnet Experience , Guide and Tutorial

------------------------------------- ProCurve J4903A Switch 2824 Software revision I.10.77 Copyright (C) 1991-2009 Hewlett-Packard Co. All Rights Reserved. RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by the Government is subject to restrictions........

Linux check NIC ethernet port network card speed

ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full ........

OpenVZ vzctl update changes how iptables work - iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. updated solution

Are you getting the same old error message even though your iptables settings for OpenVZ are correct? iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. The reason is because in newer vzctl the old way of setting IPTABLES="" in vz.conf is completely deprecated (I spent some time fiddling wondering why my settings were correct but........

Disable linux bash proxy ENV export variable

if you type Export and see something like this: declare -x all_proxy="socks://127.0.0.1:22000/" Most sites assume and tell you to check your .bashrc or /etc/profile /etc/bash.bashrc which may not apply if you've unknowingly or forgot that you setup a proxy from your GUI such as Gnome. To check in Gnome if you have a permanent proxy do the following: System -> Settings -> Network Proxy........

esniper and curl errors https://signin.ebay.com/ws/eBayISAPI.dll?SignIn: Couldn't connect to server: couldn't connect to host

I kept thinking it was esniper but somehow my bash settings have a preset proxy that was creating the issue. https://signin.ebay.com/ws/eBayISAPI.dll?SignIn: Couldn't connect to server: couldn't connect to host curl manually to any URL is the same: curl: (7) couldn't connect to host Run curl with -vvvvvv mode to see the issue: curl -vvvvvvvvvv http://realtechtalk.com * About to c........

Samsung Printer Password Login to change settings CLP

First of all to find your IP you can hold the "X" button for a few seconds and it will print out the DHCP IP. Another way to find the IP that I prefer is to login to your router or switch and find a hostname that says something like "SEC001599CD2948" which will be your Samsung printer (at least for the C3xx or C4xx series of Samsung printers). The login and password for Samsung Syncthru Webservice:........

How to root and unlock S4 in Canada Bell/Rogers/Telus/Fido I337 4.4.2

i337 Canada on Bell is hard to root or even install TWRP Installed TWRP from Odin and my computer gave me the bluescreen at the end but it seemed to be successful (after ODIN said reset). TWRP mode does not seem to enter, instead you get the Android recovery mode with Volume up + Home http://galaxys4root.com/galaxy-s4-root/how-to-root-att-or-verizon-galaxy-s4-on-android-4-4-2/ 1.)........

firefox android text size inconsistent large and small text size solution

This is very annoying and also hard for web developers who want to see how things look on Android. You may be fooled into thinking you have an unclosed bracket or incompatible code but this is the "text inflation feature" which I feel should be disabled by default. It works so inconsitently that one block of text will appear small while the other will be huge and is quite annoying. The solution is simple Settings ->Display and &q........

Thunderbird Error An error occurred while loading or saving configuration information for thunderbird. Some of your configuration settings may not work properly.

This error seems to happen randomly and especially when trying to send e-mails. Apparently it's a long-standing GNome bug but is also partially the default of Thunderbird depending on who you ask. There is no known fix that I'm aware of except to upgrade gnome and the gvfs package but this is not an option for older versions/distributions. An error occurred while loading or saving configuration information for thunderbird. Some of your configuration settings may not........

Ubuntu Linux Slow/Delayed SSH ping response Solution

I've only ever seen this in Ubuntu for some reason and it is because of the /etc/nsswitch.conf settings. So the issue is that if the hostname's reverse DNS cannot be found that you need to go back to DNS which was not the default in this nsswitch.conf file for some strange reason. Edit /etc/nsswitch.conf and replace your "hosts" line with this: #hosts: files dns mdns4_minimal [NOTFOUND=return] mdns........

WHMCS Sending Blank E-mails Solution

After the "latest" update one of our clients asked us to figure out the issue and it turns out it is related to the mail settings. Basically all e-mails were being sent with blank text/no body. The solution Go to "Setup ->General Settings ->Mail" and just click on "Save" and it will work again. Note that this assumes you didn't break things yourself by changing any settings. WHMCS may tell y........

Asterisk VOIP Sipura/Linksys PAP2T Calls Not Being Received Solution

This problem seemed to happen recently but was likely causing issues before where the phone(s) do not ring. Now there are a few reasons why this can happen especially if your adapter has DND mode enabled (disable it). However that wasn't my issue and Ionly figured it out the other day when by fluke if you're on the phone (making a call) then calls will come in. That's when Ifigured out the solution: This likely app........

PHP does not reload the php.ini setttings until the webserver is restarted

Just in case anyone is wondering that is the case, it can make troubleshooting impossible if you're making changes to php.ini but don't realize the webserver must be restarted for those changes to apply (contrary to running php-cgi which always looks up the current .ini settings).........

PHP Warning: imagecreatefromjpeg(): gd-jpeg, libjpeg: recoverable error: Premature end of JPEG file

I was having an issue with only certain random/jpeg files with the functions imagecreatefromjpeg imagecreatetruecolor and other related ones. This issue was annoying basically it seems like a libgd issue/bug with newer versions of PHP and it was difficult to trace-out. One very useful thing that helped me was using "php-cgi" and passing the query string as an argument eg: php-cgi images.php source=IMG.jpg (that way you get all the error messages wh........

Openvz OOM Centos Issue Memory Config Settings Solution

Linux box13. 2.6.32-042stab076.5 #1 SMP Mon Mar 18 20:41:34 MSK 2013 x86_64 x86_64 x86_64 GNU/Linux even setting privvmpages to a specific setting DOES not affect "free -m" in containers. This is probably a kernel issue 23:36:29 up 159 days, 7:12, 4 users, load average: 0.42, 0.44, 0.33 [root@box13 ~]# free -m total&n........

Sipura / Linksys PAP/VOIP/SIP Adapter Issue Can't receiving incoming phone calls and you're behind a NAT router (99% of people)? solution

Sipura / Linksys PAP/VOIP/SIP Adapter Issue Can't receiving incoming phone calls and you're behind a NAT router (99% of people)? 1. Login to the adapter. 2. Click on "Advanced" (location varies but usually somewhere on top) 2. Click on "SIP" 3. Scroll down to "NAT" (usually at the bottom). You'll find 2 columns with 4 rows of drop-down boxes (they'........

CPanel How To Create/Edit Default Nameservers

CPanel ->Basic cPanel &WHMSetup At the bottom you'll see them, set the nameservers you want to use and the corresponding A record if needed. Then all new domains will use those settings/nameservers. It's strange that there's no section for this specifically.........

openoffice calc landscape printing problem

openoffice calc landscape printing problem OpenOffice.org 3.2.1 OOO320m19 (Build:9505) ooo-build 3.2.1.4, Ubuntu package 1:3.2.1-7ubuntu1. It's not extending the printing and margins all the way to the edge even when setting the Page and print settings to Landscape Solution (incorrect margins set under Page): *Check the margins, my right margin was like 14cm!........

Lantronix KVM/IP Keyboard/Mouse not working in BIOS before booting the OS

I've run into two issues with Lantronix based KVMs on various servers and here's how I solved them (with that said I like these units as they are Java based and OS independent and work very well, unike some other models like Startech). 1.) If you are connected by USB only and you're sure USB support from the BIOS is enabled, you just need to click the following in Lantronix Interfaces -> Keyboard/Mouse Check "Force USB Full Speed Mode", this fixed the issu........

Howto Copy/Backup/Restore All Firefox Settings/Preferences/Addons/Bookmarks to another computer/desktop

I've used rsync again for this because I found it very simple, I've only excluded the Cache directory since it's not necessary and could be several GB in size. rsync -Phaz --exclude=Cache/* user@remotehost.com:/home/user/.mozilla/firefox/profile.default/* /home/user/.mozilla/firefox/ec1n9opl.default/ This is a great way once again to get going how you were on the old/remote computer fairly quickly. It even restores all of your history in........

Thunderbird How-To Copy/Backup/Restore Accounts and Settings to Another Computer

The best way is to use rsync, I've set it up so it doesn't copy unnecessary files, or at least ones I'm sure aren't needed. Here is the rsync command Iused (adapt to your specific Thunderbird profile location): rsync -hazv user@remotehost.com:/home/user/.thunderbird/sbrer.default/* /home/user/.thunderbird/4nyb0.default/ --exclude=global* --exclude=Cache --exclude=ImapMail --exclude=Mail This is a great way to get your e-mail accounts going on a new c........

setquota: Mountpoint (or device) / not found. setquota: Not all specified mountpoints are using quota. with openvz solution

Directadmin Error when changing user settings/saving Details Error with system Quotas setquota: Mountpoint (or device) / not found. setquota: Not all specified mountpoints are using quota. Debug Guide You have to disable and enable the quota's using vzquota on and off. After that it will work.........

Windows Secret Hidden Temp Directory to free out of disk space issues

Replace "Administrator" with your username. C:Documents and SettingsAdministratorLocal SettingsTemp Ihave often found several gigabytes of temporary files in there! Just be warned that they may not all be deletable if the files are being used by open programs (so close everything you can). This helped me in a pinch many times when for apparently no reason gigs of disk space are being used for an unknown reason.........

HowTo Migrate and Import iPhone/Outlook Contacts into Android without using GMail using .vcf files

I searched for days after getting my Galaxy Note and couldn't find a way to do this (at least not without buying programs for either Android/Windows). All I read was ways to sync and import the contacts to GMail but I don't want to use GMail for privacy reasons. GMail/Google steal all of your personal information and use it for whatever purposes they want to and may sell or release it to who knows where (I don't care what their policy says but this stuff happens), just like the default........

Ubuntu 10.04 Flash Videos have tearing/lines Solution

This is what I call a ridiculous bug in compiz that causes it. The solution/To fix it just install "compizconfig-settings-manager" Open it up and Navigate to General Options -> Display Settings Set the "Refresh Rate" to the current refresh rate of your monitor. For ATI cards with slow window dragging/response supposedly disabling "Sync to VBlank" fixes that but otherwise leave it as is.........

pgina can't login after installing

After Installing pgina I couldn't login to Windows anymore with my blank password Administrator account! An unknown error has prevented your account from being created.nrThis may be due to policy or security settings as well as other machine configuration.nrPlease consult your administrator. Hit F8 to start Windows in Safe Mode and you can login normally and then remove PGina, it shouldn't cause this problem or behavior out of the box.........

Drupal 6.2 Install and how to move install to root/non-subdirectory

drup 6.2 install $cd drupgoodinst3883/ [ drupgoodinst3883]$ ls CHANGELOG.txt cron.php index.php INSTALL.pgsql.txt INSTALL.txt MAINTAINERS.txt modules robots.txt sites update.php xmlrpc.php COPYRIGHT.txt includes INSTALL.mysql.txt install.php LICENSE.txt misc&........

Apache MPM worker vs prefork

find what MPM Apache is using, it will either be using "worker" or "prefork" apachectl -l Compiled in modules: core.c prefork.c http_core.c mod_so.c In my case it is "prefork" vi /etc/httpd/conf/httpd.conf Find the section that looks like this (by default one will normally exist for prefork and for worker, but in my case I only care a........

VOIP/Asterisk/FAX Error Problems Solution NOTICE[11389]: rtp.c:1808 ast_rtp_read: Unknown RTP codec 100 received from

NOTICE[11389]: rtp.c:1808 ast_rtp_read: Unknown RTP codec 100 received from I've found that trying several times may work, but I also read changing your Sipura VOIP adapter settings as follows helps (but it still fails for me sometimes): In adapter change the following under SIP/Advanced Codec to G711a from G711u Passthru Method from: NSE to ReINVITE FAX CED Detect Enable: Yes FAX CNG Detect........

Amarok won't play songs, keeps skipping to the next

Amarok won't play songs, keeps skipping to the next Some say install install phonon-backend-xine but it was already installed automatically, obviously that's not the problem or solution. Settings -> Configure Amarok Playback: Configure Phonon Audio Output: Music It should show your different audio interfaces, choose Pulse Audio and move it to the top of the list, do the Apply, OK and manually quit Amarok (remember to close it from the tra........

Cygwin and crontab backups via ssh/scp/rsync

Install the "Editors" and "Net" groups that will give you rsync, ssh, ssh-keygen and cron. The trickiest thing that I keep forgetting about each time is you have to run "cron-config" which adds the cron service to Windows, and without doing that obviously no cron jobs will be run thus making automatic backups impossible. Warning about rsync/cygwin and using the -a archive switch. It's a good thing I caught this because it doesn't work ri........

Wine stopped working/won't work Solution

After an upgrade wine wouldn't open anything, not even the pre-installed notepad. There are no wine logs and nothing is mentioned in any standard log file about why. I finally decided to run wine from the shell and see what's going on: wine client error:0: version mismatch 398/402. Your wineserver binary was not upgraded correctly, or you have an older one somewhere in your PATH. Or maybe the wrong wineserver is still running?........

VirtualBox/VBOX Centos 5.5 Installation Kernel Freeze Problem "NET: Registered protocol family 2" And Solution

NET: Registered protocol family 2 The above is the last thing that I ever saw, I tried pci=routeirq etc.. and it wouldn't work. The solution is to enable IOAPIC in the VBOX Settings Just enable "IOAPIC" in the settings for your Centos Guest and you'll find the kernel boots just fine. I wonder if a physical system might stall in this same way if the BIOS has IOAPIC disabled which many people do as a troubleshooting method. ........

jailkit for chroot ssh account security tutorial and fix for error

This was done on Centos butI think it's easier on Debian machines, the paths that it is set to use are tailored towards Debian, so there is some fiddling that needs to be done on Centos. This is for chrooting ssh, but jailkit has other uses than just SSH jails but I won't cover them in this writeup. 1. Install jailkit yum install jailkit 2. Setup Jail Home mkdir /home/jail chown root:root /home/ja........

exim high load and dozens of processes

This server was experiencing loads of up to 80 and maxing out the RAM and kmemsize on a CPanel VPS. There were literally dozens if not hundreds of exim processes. I have no idea why exim has such a design that would allow it to consume this much CPU and RAM. Any normal MTA should not be spawning so many processes, it should be processing them in sequence and if it is going to spawn hundreds of processes in response to a large volume of mail, it's better to have a delayed del........

Fix Slow 2D Graphics Xorg.conf Ubuntu/Debian/Mandriva Linux

I'm using Ubuntu 8.04 but anyone using older kernels will find this may apply to them. My Intel graphics are very slow with the default Xorg settings but by using "EXA" acceleration, scrolling down windows of text becomes pretty snappy. Just edit /etc/X11/xorg.conf Section "Device" Identifier "Configured Video Device" &nb........

Asus Eee PC 1000HE Crashed/Need To Recover/Restore Windows? Easy Solution is Hitting F9

I'm not a fan of Asus and won't be buying another because of having to fight Asus over a bogus warranty denial (it's a long story but they only replied about how to RMA my unit weeks later on the EXACT day the warranty expired). Anyway, it's just a matter of hitting F9 to do this, there's no need to worry about booting from USB or CD (unless of course you want a different OS eg. Windows XP Pro, Vista/7, or a flavor of Linux or Unix). Also remember that you need to fully/properl........

Windows XP How To Edit/Find Recent Documents and "File -> New" Templates to create New Word Document, Text/Notepad, Excel etc...

All you have to do is browse to: C:Documents & SettingsYourUserName and you'll see the following: Inside "My Recent Documents" are of course shortcuts to the most recent documents you opened Inside "SendTo" is your sendto, you could edit that to Send a file to a network destination, your Flash Drive........

Updated to Version 3.8 and can't login

Updated to Version 3.8 and can't loginSSHD accepts my password but then hangs at "Last login: Wed Sep 13 21:30:02 2006 from" This occurred during a yum update after upgrading my release, installing the new kernel and rebooting. I got kicked out of sshd after seeing the following during yum update: telnet 100 % done 85/476 tux 100 % done 86/476 ntsysv 100 % done 87/476 rpmdb-redhat 94 % done 88/476........

Debian/Ubuntu/Kubuntu Bash/Console/Terminal/Putty Home and End Keys Don't Work or Produce a ~

This is a very weird, annoying and bizarre quirk with many distributions, especially Debian. The home and end keys don't work, but it's a simple fix as long as you found this article :) You just have to edit /etc/inputrc: Find the commented lines as shown below: # "e[1~": beginning-of-line # "e[4~": end-of-line *If you can't find the above, just copy and paste the code below into your inputrc, it will en........

Adventures in pre-paid SIM Cards and data GPRS/Edge/3G in China with China Mobile in Shenzhen, Guangzhou, Shanghai, Beijing and other cities

This really is a difficult and confusing process for non-Mandarin speakers, but here's what I've done and learned so far: You can purchase an "M-Zone" China Mobile pre-paid SIMCard from almost anywhere but I tried to purchase mine from Suning (a large electronics dealer) hoping they would be able to help me or answer my questions but my plan didn't work out at all. At Suning once I found someone who spoke some English they gave me the 55 RMB M-Zone China Mobile P........

iPhone Enable Tethering Manually Update ipcc Carrier Settings/Update via SSH

Everyone says there is a "manual" way of doing it and then they tell you to use iTunes, but if you're like me, you're travelling on business in a foreign country and your laptop does not have iTunes and you don't have a way of getting it and/or don't want it. For this example I'm using the provider "du" in Dubai, UAE (United Arab Emirates) but this method works for virtually all providers. The requirements in this case to truly "manually update........

Unixbench Score with Glusterfs/Openvz & Quad Core Xeon - Updated with GlusterFS 2.0.8

You might remember my original GluserFS/OpenVZ benchmark which produced a horrible 29.8 This is the exact same system, but using the latest 2.0.8 (with some small files patch which speeds up performance) you can see it is about 25% faster. I also haven't tuned my config files at all, but there are some settings that should increase performance on small files which I believe i........

Have an OpenVZ VPS/Linux Virtual Private Server and nothing works right?

A VPS Server I had just wasn't working right, code that I migrated there just wasn't working. For example, it kept telling me the connection to the database was unsuccessful, halfway through iterating through results it already had. Then I realized it wasn't my code. Ichecked my /proc/user_beancounters and found this: cat /proc/user_beancounters Version: 2.5 uid resource held maxheld barrier limit failcnt........

Apache Ignoring/Not processing .htaccess file

I was getting very frustrated one day wondering why it appeared my .htaccess file was being ignored and not processed by Apache. No matter what I did it was obvious that Apache didn't care about my .htaccess file. Then I realized that the default settings must be in effect, which is that my vhost didn't explicitly allow me to override the default settings. This usually comes down to your vhost settings. Make sure you have an entry like this in your Apache vhost settings in........

How To Save iptables firewall rules Centos/Redhat/Fedora Linux

This is something that annoys a lot of people, fortunately the Redhat style OS's are the most simple in this respect. I disagree that Debian's way makes sense, it is more of a hackish approach in how they implement iptables. Anyway, for those who are using Redhat/Centos style OS's it is very simple. Set your rules from the shell/command prompt and to save the iptables firewall rules so they are remember/loaded on boot just run this command: service iptables........

iPhone Create Silent/Free Custom Ringtone jailbroken/jailbreak iPhone

As shown below you can find ringtones in the "/private/var/stash/Ringones*" directory of your iPhone. Different reports have said that the .m4r format is really an MP4 file and some have said AAC and some also say "it's the same as the M4A" format. Whatever the case is, one easy way is to install the silent theme from Cydia and copy that into your ringtones directory. /private/var/stash/Ringtones.sh7cLj root# ls Alarm.m4r ........