• Docker Container Onboot Policy - How to make sure a container is always running


    Generally most containers are by default set not to start automatically. Ther eare 3 settings for the "RestartPolicy" of containers: No: Do not automatically restart the container (default). Always: Always restart the container regardless of the exit status. Unless-stopped: Always restart the container unless it is explicitly stopped. On-failure:........

  • pptp / pptpd not working in DD-WRT iptables / router


    Although it is well-known that pptp is not secure and is subject to many forms of attacks, the reality is that a lot of legacy and embedded devices use pptp. I argue that if it is being used for routing or remote access or over an already secure connection (eg. another VPN like ikev2) then this is still acceptable. Or in a LANor in a public environment where no private data is exchanged. However, if the nature of the data is extremely sensitive, you should do whatever........

  • Using Cisco CME Router with Asterisk as a dial-peer


    #Remember that you need a valid gateway IPunless the Asterisk server is on the same subnet and LAN Set Valid Gateway IP (if you don't have one already) ip route 0.0.0.0 0.0.0.0 GATEWAYIP Enable VOIPTrust voice service voip ip address trusted list ipv4 0.0.0.0 0.0.0.0 sip Set Credentials For Asterisk and Register To Asterisk sip-ua........

  • Virtualbox host Only Network Error Failed to save host network interface parameter - Cannot change gateway IP of host only network


    In newer versions this is a very stubborn issue. Here is how you fix it. Step 1 - Create networks.conf sudo mkdir /etc/vbox/ sudo vi /etc/vbox/networks.conf put this in: In our case we can use the slash /16 range of 192.168.0..0, change the subnet accor........

  • Abusive IP ranges blacklist


    Make sure this makes sense for you but I've started to block a lot of commercial Cloud services and easily accessible providers as they are a very high source of abusive traffic. The cost savings for a lot of organizations are huge, as you now have less bandwidth usage and less resource usage from garbage/bot/malicious traffic. This mainly works for when you can be reasonably sure that your audience has no business visiting your service(s) from freely accessible commercial IP ........

  • efibootmgr: option requires an argument -- 'd' efibootmgr version 15 grub-install.real: error: efibootmgr failed to register the boot entry: Operation not permitted.


    This sometimes happens when trying to install the EFIversion of grub to a device when you are booted into Legacy/MBR mode. It doesn't seem to occur on all machines, but some and seems somewhat BIOS dependent. grub-install --target=x86_64-efi /dev/sda Installing for x86_64-efi platform. grub-install.real: warning: Couldn't find physical volume `(null)'. Some modules may be missing from core image.. grub-install.real: warning: Couldn't find physica........

  • Linux Debian Mint Ubuntu Bridge br0 gets random IP


    This can break things easily in remove environments where it was normally easy to convert a normal eth0 to a bridge under br0, and that bridge would normally have the same MAC address by default, which is desirable for most situations. In Debian 11 this is different for some reason now. https://unix.stackexchange.com/questions/681013/bridge-gets-random-mac-........

  • docker swarm silly issues


    The error below can be caused by a gateway that is unpingable: docker swarm join --token SWMTKN-1-1kogg8da68gtb1j7ezaddowyy9s0an5s9tue758o20k18liskw-5h3f61hrrmv3u6agshvbtcklf 172.16.1.80:2377 Error response from daemon: manager stopped: can't initialize raft node: rpc error: code = Unknown desc = could not connect to prospective new cluster member using its advertised address: rpc error: code = DeadlineExceeded desc = context deadline exceeded........

  • Linux custom kernel is huge solution


    You may have been expecting a normal sized kernel but if you don't disable these .config options you may have a kernel that is several gigabytes. CONFIG_SLUB_DEBUG=no CONFIG_DEBUG_INFO=no CONFIG_DEBUG_MISC=no Rebuild and you should find that the kernel is the normal and as expected size.........

  • Docker Swarm vs Kubernetes Comparison Guide


    A lot of companies are unsure which solution to choose and many may not be aware of Docker Swarm as an alternative to Kubernetes. One thing that many Sysadmins find is that Docker Swarm is simply easier, quicker to setup and maintain by far than Kubernetes.........

  • When is it time to leave your VPS/VDS Cloud Hosting Provider?


    When Is It Time to Leave Your VPS, VDS, and Dedicated Server Provider? Choosing the right hosting solution—be it Virtu........

  • Linux how to get list of all timezones on system Ubuntu


    find /usr/share/zoneinfo/|sed s#"/usr/share/zoneinfo/"##g|grep "/"|grep -v posix|grep -v ^"Etc/"|grep -v ^right|grep -v ^"SystemV" Africa/Addis_Ababa Africa/Abidjan Africa/Blantyre Africa/Lusaka Africa/Casablanca Africa/Libreville Africa/Asmara Africa/Bujumbura Africa/Dakar Africa/Lagos Africa/Malabo Africa/Harare Africa/Kigali........

  • Proxmox install issue cannot see the buttons or install wrong / bad resolution cannot see the entire screen problem solution


    If you are using a hypervisor to test Proxmox (eg. Vbox) then changing the video card/display adapter can fix it. For example VboxSVGA causes the issue but switching to VMSVGA fixes it. For example VboxSVGA causes the issue but switching to VMSVGA fixes it. ........

  • How To Setup Python3 in Ubuntu Docker Image for AI Deep Learning


    The issue is that Docker images are stripped down, so many tools and even python3 is missing, so you'll have to build or update the actual image yourself. I assume you have started an image with something like this and that you have the Nvidia Toolkit installed (assuming you are using GPUs). If you're not using nvidia just remove --runtime=nvidia --gpus all. docker run -it --runtime=nvidia --gpus all ubuntu bash These works for most images li........

  • Docker cannot work on other overlayfs filesystems such as ecryptfs won't start overlayfs: filesystem on '/home/docker/overlay2/check-overlayfs-support130645871/upper' not supported as upperdir


    This does not seem to be officially documented but makes sense that an overlay on an overlay does not work and is considered an unsupported filesystem as is even NTFS . Some admins/organizations try to use ecyptfs as a simple solution to encrypt the contents of Docker. Instead, you could probably........

  • How to install and configure haproxy on Linux Ubuntu Debian


    haproxy is one of the best known and widely used Open Source load balancers out there and a strong competitor to nginx. haproxy is used by many large sites per Wikipedia: HAProxy is used by a number of high-profile websites including GoDaddy, GitHub,........

  • Virtualbox Best Networking Mode In Lab/Work Environment without using NAT Network or Bridged


    Virtualbox is a very powerful tool, but for some use cases it is less than optimal. Say you are in a work, lab or other environment where you are not alone on the physical network and there could be overlap of IPs, but you need all of your VMs to be contactable from your host, VMs need to communicate with each other, and VMs need internet. NAT Network will give you VM to VM communication and internet, however, it is buggy and unstable. It also doesn't allow host to VM co........

  • Linux How to Check Which NIC is Onboard eth0 or eth1 Ubuntu Centos Debian Mint


    So say you happen to have 2 NICs of the exact same chipset, they will generally show up as the same name, with possibly a different revision in lspci. Normally this is not an issue if you have a server with 4 NICs, generally the eth0 to eth3 appears from left to the right (or right to left on some vendors) so it doesn't take much figuring out. Generally if you have different chipsets for different NICs, it should be easy to know which one is eth0 or the first NIC in the OS.........

  • VboxManage VirtualBox NAT Network Issues Managment Troubleshooting


    If you find your NAT Network is not working properly, the first thing you may want to do is list the networks, check their status and make sure the Network is actually started and configured as you expect (eg. is DHCP on and enabled?). This is a long known, unresolved bug that seems to affect Version 6 randomly and disportionately on especially Mint 20/Ubuntu 18. https://www.virtualbox.org/ticket/1474........

  • Dell PowerEdge Server iDRAC Remote KVM/IP Default Username, Password Reset and Login Information Solution


    Are you new to the company, datacenter or a third party who is responsible for deploying a fleet of servers from scratch. The first step is to normally login to the KVM so you can perhaps manually reinstall, PXE boot the Cloud Image or reimage/reinstall an OS but you need access to the KVM/IP or what Dell calls iDRAC. It's common that you may have forgotten this information or that another employee or colleague has changed the info and did not tell you, that they have left the........

  • Nvidia Tesla GPUs K40/K80/M40/P40/P100/V100 at home/desktop hacking, cooling, powering, cable solutions Tutorial AIO Solutions


    Do you have access to some old Tesla GPUs and want to try them at home in your Desktop or old Server? Some people have wanted to try these units for gaming but keep in mind they have no video out port, they were only meant for AI applications such as Deep Learning. The easiest way by far is to choose an AIservice that has everything ready to go, perhaps with a bunch of Docker or Kubernetes containers. This can be done with Cloud services like Google, Amazon and many........

  • Cisco Switch / Router How To Restore Factory Default Settings


    1.) Make sure your conf register is 0x2102 Do show version and at the very end of the output you will see the Configuration register. show version Configuration register is 0x2102 If the config register is not 0x2102 then enter this command: r1#configure terminal r1(config)#config-register 0x2102 r1(config)#end 2.) Let's Erase the NVRAM/flash........

  • Error opening tftp://10.0.2.2/network-confg (Permission denied) - How To Fix Cisco Router Switch Error Solution Console


    How To Fix This Cisco Switch/Router Error %Error opening tftp %Error opening tftp://10.0.2.2/network-confg (Permission denied) %Error opening tftp://10.0.2.2/cisconet.cfg (Permission denied) %Error opening tftp://10.0.2.2/router-confg (Permission denied) %Error opening tftp://10.0.2.2/ciscortr.cfg (Permission denied) %Error opening tftp://10.0.2.2/network-confg (Perm........

  • How To Add Default Gateway in Linux using the ip route command routing


    Adding a default route is very simple with this command Just replace 192.168.1.1 with the IPof your GW. ip route add default via 192.168.1.1 How can you delete this default route if you messed it up? It's just the opposite with "delete" instead of add ip route del default via 192.168.1.1 This is the equivalent of the "route command's" route add default gw 192.168.1.1........

  • Linux Mint Ubuntu Ubiquity Installer Bug EFI Installed To Wrong Partition Solution


    Just an FYI that the installer ignores your selection of Boot Loader, as it was intended for MBR/Legacy. The installer horribly, even when choosing "Something Else" and manually partitioning and creating an EFIin your install drive, will still install grub to the first EFI partition it finds, even if you are following a guide like this to avoid wiping out the M........

  • i915 nouveau Nvidia GPU not starting lightdm Xorg failing solution for Could not determine valid watermarks for inherited state


    It may appear to be an Xorg or lightdm/gdm/mdm error but in reality for many users with this issue, it's a driver conflict and issue. I had a system that had two GPUs, an Intel and Nvidia GPU. The only thing that got it working was to remove the nouveau driver and blacklist it so it never came back, then the Intel GPU works fine without these issues. Solution sudo rmmod nouveau add nouveau/other driver to blacklist edit th........

  • br0: received packet on bond0 with own address as source address Linux Solution Mint Debian Redhat CentOS bridge bridging


    A quick fix is to run this command: sudo brctl setageing br0 0 This causes the aging of the MAC address to time out immediately or in 0 seconds, which delete the entry frmo the FDB (Forwarding Database) and causes the error to go away. The default time is 300 seconds or 5 minutes. You can also add it under your br0 definition like this in /etc/network/interfaces to make it permanent and automatic: auto br........

  • LightDM Mint Ubuntu Debian won't start errors Nvidia Graphics


    This error implies that there may be an issue with Xorg or maybe your NVIDIA GPU cannot start or initialize: 35 laptop kernel: [ 2031.857704] nvidia: loading out-of-tree module taints kernel. 35 laptop kernel: [ 2031.857724] nvidia: module license 'NVIDIA' taints kernel. 35 laptop kernel: [ 2031.857725] Disabling lock debugging due to kernel taint 35 laptop kernel: [ 2031.873280] nvidia: module verification failed: signature a........

  • How To Do Linux Network Bonding Teaming in Mint Debian Ubuntu


    Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........

  • Docker Tutorial HowTo Install Docker, Use and Create Docker Container Images Clustering Swarm Mode Monitoring Service Hosting Provider


    The Best Docker Tutorial for Beginners We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........

  • How To Create OpenVPN Server for Secure Remote Corporate Access in Linux Debian/Mint/Ubuntu with client public key authentication


    Why choose OpenVPN instead of a firewall appliance? OpenVPN can be a reliable and easy replacement for traditional hardware or just be an additional tool that your company uses so that the firewall can focus on its job rather than acting as a VPNappliance at the same time. When comparing OpenVPN with traditional firewal........

  • HongKong VPS Server, Cloud, Dedicated Server, Co-Location, Datacenter The Best Guide on Hong Kong, China Internet IT/Computing


    In our 2024 VPS Server/Cloud Buyer's Guide, we place the location of your VPS/hosting/server as one of the priorities that is often overlooked. 2024 Update - Datacent........

  • Wazuh / OSSEC Install and Configuration Howto Tutorial Guide for Monitoring Agents SIEM


    How To Install Wazuh Server / Quickest Installation Wazuh (forked from the well known OSSEC project) is a full SIEM (Security Information Event Management) that works extremely well with the platforms it natively supports as an "Agent", which allows you to do scans of everything such as all processes running, CVE vulnerability check, incident reporting etc... Prerequisites: A lot of issues with Wazuh seem to be caused by i........

  • Proxmox How To Enable Ceph Distributed Storage Cluster with OSD and Pools


    How To Install Ceph If you stopped an install of Ceph midway you will need to manually restart it with "pveceph install" Remember that your VM needs to have working internet (gateway) and DNS in order to connect to the apt repo to download all of the packages that Ceph requires. Remember to repeat these steps for each node that you want Ceph on. ........

  • How to install Kubernetes with microk8s and deploy apps on Debian/Mint/Ubuntu Linux


    Kubernetes Easy Beginners Tutorial/Architecture Guide Kubernetes is known as container orchestration and we should start at explaining the container part of it. A Container is what runs the actual application and based on an Image, and are more comparable to something like an LXC Container, Virtuozzo/OpenVZ using the Linux Kernel Namespaces feature. Containers run these images as independent, isolated operating environments under the O........

  • VirtualBox VBox Nat Network Handing Out Wrong IP Address Subnet Solution


    This seems to be an ongoing issue that is still reproducable in the latest Ubuntu Vbox 6.x. The default NAT Network range is usually 10.0.2.0/24. If you change this range it does not seem to work properly. Say we change the range to 10.50.1.0/24 If you get a new lease you will find that you get an IP from the old range but the default gateway is from the new range. ........

  • Linux can't boot/grub boot loader screen with no options solution


    Usually if you get the grub boot loader and it doesn't show any boot options, it's because grub was not installed correctly and/or the partition that it is supposed to be on has changed or does not exist. It can also happen if you install Linux to one drive, but the boot loader to another by accident, whether EFI or MBR/Legacy mode. You can normally fix your booting/bootloader/MBR/EFI it by chrooting into your root partition: #become root sudo su........

  • EFI PXE grub2 Howto guide for Linux EFI PXE Booting on Debian, Mint, Ubuntu, RHEL


    Just a quick note and warning is that if you are testing to see if EFIPXE booting works on a VM, MAKE SURE it actually works. For example Iinitially tested using my Distro's QEMU 2.5+dfsg-5ubuntu10.46 and ovmf BIOS firmware (OVMF supports EFI). However, I found on old versions of QEMU (like 2.5), EFIbooting with GRUB NEVER works so it may appear that you have made a mistake when everything is fine when you boot a physi........

  • Linux Grub not booting the intended kernel solution in Debian, Mint, Ubuntu how to specify which kernel to boot by default


    Traditionally kernels were numbered starting from 0 but by default the "new style" of grub boot loading considers each subkernel item to be different so if you have 3 entries for 4.40-148 rather than counting for 1. To get the expected behavior let's show this example and how we can boot it We do a grep on menuentry in /boot/grub/grub.cfg to see all of the bootable kernels rather than scrolling through loads of extra entries we don't care about (thou........

  • Mikrotik RouterOS CHR/ISO Basic and Quick Setup Howto Guide


    Many people may not be aware that you can turn commodity hardware into a Mikrotik OS and there are various options which is "CHR" (Cloud Hosted Router) which is a VMimage meant for Virtualization only (seriously, I've tried to dd the image to a physical server and it just crashed as it does not contain any drivers for physical). One note as well if you are trying to do a baremetal install you may get an error "Error Loading Operating System" or........

  • How To Boot, Install and Run Windows 2000 on QEMU-KVM


    Interestingly enough Windows 2000 works fine on QEMU 64-bit but you have to specify Pentium as your CPU otherwise it doesn't complete the install (it will not pass the detecting/setting up devices phase). -vga cirrus is wise because it is supported by Windows 2000 and allows higher resolutions and 24-bit color. -cpu Pentium emulates an old computer and is necessary for install to complete -device rtl8139 is important as this oldschool Realtek 8139 NIC is supported by W........

  • How To Replace Audio Track of Video using ffmpeg


    A very common use case is that you don't want to waste time using a video editor that requires you to open it up and manually import the video clip and audio clip, then manually delete the old audio track and import the video and new audio. That's too much work and time since we don't want to go through the hassle. ffmpeg is our solution, all we have to do is specify 3 variables and we're done! -i Windows2019-Server-Noaudio.mp4 is our in........

  • Linux Mint Ubuntu Debian CentOS Dual Boot Install Issues


    The best way to avoid this problem is to understand how your BIOS is setup to boot. Often newer machines will default to U(EFI) which is different than the traditional MBR/Legacy mode. The problem is that this may not be apparent, often a BIOS Boot Menu will show a Legacy Boot Option and EFIOption without defining it. A good example of this is if your USB is called "Kingston" you may see in your Boot Menu "Kingston" and also "Ubuntu"........

  • Linux Mint/Debian/Ubuntu/Centos Installer black grub screen and blank screen after trying to boot installer or main OS


    This happens to a lot of Nvidia users especially users of newer cards like the RTX series. If for example you are trying to boot and install Linux and you get a black and white grub2 screen instead of a nice graphical welcome installer, you probably suffer from this bug. It is normally followed by the user booting and finding they just have a blank/black screen. Here is the quick flow of steps to fix it: If you get a black grub scree........

  • apcupsd how to setup and monitor APC UPS units


    It really seems limited in that it can mainly give you the things you would see on the physical unit such as load etc.. wget https://downloads.sourceforge.net/project/apcupsd/apcupsd%20-%20Stable/3.14.14/apcupsd-3.14.14.tar.gz?r=https%3A%2F%2Fsourceforge.net%2Fprojects%2Fapcupsd%2Ffiles%2Flatest%2Fdownload&ts=1598115866 tar -zxvf apcupsd-3.14.14.tar.gz cd apcupsd-3.14.14 [root@somebox apcupsd-3.14.14]# ./conf........

  • access denied by acl file qemu-kvm: bridge helper failed


    /usr/libexec/qemu-kvm -enable-kvm -boot order=cd,once=dc -vga cirrus -m 4096 -drive file=~/23815135.img,if=virtio -usbdevice tablet -net nic,macaddr=DE:AD:BE:EF:D4:AB -netdev bridge,br=br0,id=net0 qemu-kvm: -usbdevice tablet: '-usbdevice' is deprecated, please use '-device usb-...' instead access denied by acl file qemu-kvm: bridge helper failed [root@CentOS-82-64-minimal 23815135]# /usr/libexec/qemu-kvm -enable-kvm -boot order=cd,once=dc -vga cirrus -........

  • Linux NIC connecting at 100M instead of 1000M gigabit speeds? It could be overheating


    I was using a small box as a router and one of the ports started going off and coming back at 100M. I truly believe it is simply that it was a case of overheating. Although CPUtemps were only about 67 degrees, the physical box itself was almost burning hot. Isolved the cooling issue and never had the issue again. Jul 28 15:09:27 swithbox kernel: e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx Jul 28 15:09:28 swithbox kernel:........

  • How To Get Started on Ubuntu with gpt-2 OpenAI Text Prediction


    apt install software-properties-common add-apt-repository ppa:deadsnakes/ppa apt update apt install python3-pip apt install python3.7 curl gnupg python3.7-dev git ln -s /usr/bin/python3.7 /usr/bin/python3 pip3 install numpy keras_preprocessing curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add - echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........

  • How To Install NextCloud on Centos 7 and Centos 8


    yum -y install wget unzip wget https://download.nextcloud.com/server/releases/nextcloud-18.0.2.zip unzip nextcloud-18.0.2.zip yum -y install php php-mysqlnd php-json php-zip php-dom php-xml php-libxml php-mbstring php-gd mysql mysql-server Last metadata expiration check: 0:58:02 ago on Fri 13 Mar 2020 02:12:49 PM EDT. Dependencies resolved. ===================================================================........

  • Radeon R3 GPU on Debian Crashing


    Occasionally my whole screen locks up and I cannot even swith to the console and I find this in my syslog: *-display description: VGA compatible controller product: Mullins [Radeon R3 Graphics] vendor: Advanced Micro Devices, Inc. [AMD/ATI]  ........

  • Howto Set Static IP on boot in initramfs for dropbear or other purposes NFS, Linux, Debian, Ubuntu, CentOS


    This is only really necessary in the case you don't want DHCP. If you are dealing with an encrypted LUKS server on the internet, you will often want to have a static IP so you know which IP to connect to (or if you have a semi-static IP assigned by DHCP). SET IP Address by /etc/initramfs-tools/initramfs.conf IP Address=192.168.1.27 Gateway=192.168.1.1 Subnet Mask: 255.255.255.0 Hostname=myhome.com IP=192.1........

  • Debian and Netplan


    Create your netplan file vi /etc/netplan/01-netcfg.yaml network: version: 2 renderer: networkd ethernets: ens3: dhcp4: no ........

  • bash script kill whois or other command that is running for too long


    Adjust to suit your needs. Currently this would kill any whois process running for more than 30 seconds or more than 1 minute. Add it as a cronjob. The motivation is that some commands have no timeout and just end up using up CPU and memory for no reason while never exiting to free resources. #!/bin/bash IFS=$(echo -en "nb") for pid in `ps aux|grep whois`; do echo "pid=::$pid::&qu........

  • Debian Ubuntu Mint Howto Create Bridge (br0)


    Having a network bridge allows you to bridge traffic under multiple devices so they can talk natively without using any special routing, iptables/firewall or other trickery. To create your bridge you need the bridge-utils package for brctl and if you want to do things like bridge VMs that run on a tap device you will need the uml-utilities which provides "tunctl". 1.) Install the utilities to make our bridge sudo apt-get i........

  • Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM


    The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........

  • ssh reverse proxy to enable remote access behind a LAN and firewall


    So say you are behind a typical NAT/LAN setup whether at home, work or while travelling. What if you have a computer or server that you need to connect to from the outside? Yes you could use a VPN but a quick and dirty, temporary and secure way is to use SSH's Reverse Tunneling Proxy feature. Requirements On the remote ssh server host you need the GatewayPorts option enabled in sshd_config (be........

  • Cisco Router Setup Guide and Tutorial Howto With Commands and Examples


    In most of the Cisco router IOS I find the ports like ge0/0 ge0/1 and ge0/2 or whatever your ports are down. They will not even give you a link light. So one of the first tasks should be getting the port you are working with up. In my case the first goal is often connectivity with the LAN and WAN. LAN = your local area network (eg. in the office/home ) WAN= your ISP/public internet (eg. fiber/cable/dsl/ethernet).........

  • Cisco DHCP Snooping Relay Setup Information


    Switch#show ip dhcp snooping Switch DHCP snooping is disabled DHCP snooping is configured on following VLANs: 1 Insertion of option 82 is enabled circuit-id format: vlan-mod-port remote-id format: MAC Option 82 on untrusted port is not allowed Verification of hwaddr field is enabled Interface&nb........

  • Cisco Switch Setup Guide Command List


    Enter configuration console: enable configure terminal This is important because if your console doesn't look like below none of the commands will work! Switch(config)# Save and Apply Settings wr Show Switch Configuration: show run Show Port List/Sta........

  • Using Microsoft's Group Policy Management Editor (GPME) To Change Default Permissions and Internet Explorer Security Settings


    The defaults in Windows 2016 server leave clients crippled so they can't even download basic files or software. But Group Policy Management Editor comes to our rescue! Use cmd or Powershell and run: gpme.msc Choose your domain/computer and then navigate like below and create a new menu entry for IE11 or whatever your version is. Don't be worried if the highest version is IE10 it means that it applies to IE10 AND above.........

  • Thunderbird How To Disable An Email Account


    Navigate to Tools -> Account Settings -> Server Settings Uncheck the following: "Check for new messages on startup" "Check for new messages every NN minutes" "Automatically download new messages". Source: http://forums.mozillazine.org/viewtopic.php?t=635510........

  • Linux How To Create A RamDisk


    size = the amount of RAM (m for megabytes) /mnt/ram = the mount location of the ram disk (change to the path you want it mounted to) mount -t tmpfs -o size=4096m tmpfs /mnt/ram/ Example test in an old server: You can see that when reading if you don't specify bs1=M the read speeds are several times slower (eg. 450MB/s vs 2.1GB/s) mount -t tmpfs -o size=4096m tmpfs /mnt/ram/^C root@testserver:~# dd........

  • Why SMART is not smart at all and doesn't properly predict disk errors that cause a kernel panic or crash


    Before getting into the output here is my typical experience with SMART, there is what I call a "bad disk" with pending and uncorrectable sectors that cannot be reallocated. It has caused a kernel panic and system crash repeatedly as we can see from the logs. But SMART says it has "PASSED" its self assessment. SMART is still useful to me but it is more about looking at Current_Pending_Sector. Any time I have had anything but 0 for that attribute it........

  • How Does Cisco CUCM (Cisco Unified Communication Manager) Work?


    Cisco's CUCM (Cisco Unified Communication Manager) is a system that combines voice, video, data and mobile products into a single unified management suite. At its core, the CUCMis like a "Super PBX" that controls the flow of all communications through an organization even single or multiple site deployments. Cisco's CUCMmakes communication more effective and simple through centralized management and unification of communications resources.........

  • systemd management using systemctl and journalctl to check systemd logs


    systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system. The key commands or arguments you will use with systemctl are the following: Unit Commands: list-units [PATTERN...] List loaded units &nbs........

  • How to download gajim 0.16.9 XMPP/Jabber client so you can use OMEMO encryption


    #Linux Mint 18.2 how to install gajim .16.9 so you can use OMEMO encryption: sudo apt-get install python-axolotl python-nbxmpp wget https://gajim.org/downloads/0.16/gajim-0.16.9.tar.gz tar -zxvf gajim-0.16.9.tar.gz cd gajim-0.16.9 ./autogen.sh ;make;sudo make install #if you get this error you need to get a newer python-nbxmpp from here: gajim Gajim needs python-nbxmpp >= 0.6.1 to run. Quiting...........

  • vmkping -I vmk1 10.0.2.69 PING 10.0.2.69 (10.0.2.69): 56 data bytes sendto() failed (Host is down)


    [root@localhost:~] vmkping -I vmk1 10.0.2.69 PING 10.0.2.69 (10.0.2.69): 56 data bytes sendto() failed (Host is down) vsphere distributed switch vmotion not working [root@localhost:~] esxcfg-route -l VMkernel Routes: Network Netmask Gateway Interface&........

  • Debian/Ubuntu/Mint Linux How To Set VLAN in /etc/network/interfaces


    You can find many ways to specify the VLANin your network configuration but Ifind this is the simplest and quickest. In this case we are talking about a bridged adapter "vmbr0" but it works even if you just had a normal non-bridged interface. The key here is that in vmbr0 you'll notice there is no IP address. We just specify "manual". Below it is a similar stanza for "vmbr0.58" in this case 58 represents the VLAN (change........

  • VMWare Vsphere VCSA Graphical Install Creates json


    yes it does create its own json ============================================ cat /tmp/vcsaUiInstaller/ovftool-20180809-175238948-20180809-175603497.log |grep -i json 2018-08-09T17:56:04.238-07:00 verbose OVFTool[30966] [Originator@6876 sub=Default] Manifest file entry: SHA1(VMware-vCenter-Server-Appliance-6.7.0.12000-8832884_OVF10-file1.json) = 1deb658c724767697587d5909c4051c01813e6a1 --> ........

  • Debian Mint Ubuntu compiling xmr-stak


    sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........

  • *** These critical programs are missing or too old: gawk


    checking whether autoconf works... ../configure: line 5377: 7325 Segmentation fault $AUTOCONF $ACFLAGS configure.in > /dev/null 2>&1 no configure: error: *** These critical programs are missing or too old: gawk *** Check the INSTALL file for required versions. ........

  • PayPal IPN Failed "result: IPN Handshake Invalid"


    This is often the result of PayPal's "item name" or another name having invalid characters or not supporting Unicode. 173.0.81.1 - - [17/Jul/2018:13:39:45 -0400] "POST //modules/gateways/callback/paypal.php HTTP/1.1" 406 - "-" "PayPal IPN ( https://www.paypal.com/ipn )" A good clue is if you check the debug output of the IPNand find a mandatory column empty. ........

  • wodim / cdrecord error cannot burn DVD or BDR .iso Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error


    dvd+rw-mediainfo /dev/sr0 INQUIRY: [ASUS ][BW-16D1HT ][3.00] GET [CURRENT] CONFIGURATION: Mounted Media: 11h, DVD-R Sequential Media ID: RITEKF1&n........

  • VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI


    #mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........

  • Cannot create gradle for conversations


    The main issue is it looks like Java is not configured to accept the invalid ssl cert that is coming from the download location. Exception in thread "main" java.lang.RuntimeException: javax.net.ssl.SSLException: java.security.ProviderException: java.security.InvalidKeyException: EC parameters error export ANDROID_HOME=/home/user/Downloads/tools/ Conversations-master$ ./gradlew Downloading https://services.gradle.org/distributions/grad........

  • mail command line examples of how to send an email using Linux / Unix and the Bash Shell or Scripting


    A simple way that may work for a lot of people who just need basic output for their scripts or daemons to announce an action is this: echo "body or message" | mail -s "realtechtalk.com" user@domain.com If you want to send a text file as the body just do this instead: mail -s "realtechtalk.com" user@domain.com < /tmp/sometxtfile.txt These are some ve........

  • OpenVPN cannot ping remote IP routing loop issue after connecting


    Sometimes if you have a very basic configuration OpenVPN on the client side for some reason sends all traffic to the OpenVPN server IP through the tun0 which is of course impossible and creates a block or routing loop. This is because you need to use your normal ISP/LANgateway to hit the OpenVPN server if it is remote/offsite as is usually the case. So if you are connected to the OpenVPN through say a tun0 device and your routing is set to connect to the OpenVPN&nbs........

  • Linux Mint Black Screen after boot no graphics solution


    This is not the normal "black screen"issue and I was shocked to eventually find out why. The normal advice of reconfiguring Xorg didn't work. Even booting into "Recovery Mode" did not help. Here is the short end of the stick that fixed it: sudo apt-get install mdm mate-desktop-environment Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled. This must be whe........

  • Linux Mint Ubuntu Debian How To Disable Webcam Automatically Onboot To Prevent Spying and Privacy Violations


    It is well known hackers, the NSA, CIA and other groups have created malware to secretly turn on your webcam and microphone on your phone, tv etc.. But fortunately on our computers and laptops we have some options. Most webcams use the "uvcvideo" kernel module / driver. You can disable this in two ways on boot. I recommend both just as a failsafe. Disable it on rc.local once your system boots automatically Add the followi........

  • tftp: client does not accept options - solution if you are using UEFI PXEBoot disable it!


    tftp: client does not accept options I spent the good portion of a late evening on this double checking settings that I know always worked right for tftp! This error can also happen if you are trying to boot PXE in UEFImode. Enter your BIOS and change it to "Legacy PXE" or non-UEFI PXE mode and you'll be good to go!........

  • Linux how to view video card make and exact model


    Normally lspci will show you just like this and would suggest they are exactly the same card: 1a:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Ellesmere [Radeon RX 470/480/570/580] (rev e7) 1c:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Ellesmere [Radeon RX 470/480/570/580] (rev e7) lspci -vnn is the answer As we can see one is a Gigabyte and the other is an MSI card. Wha........

  • How to Update Linux /usr/share/misc/pci.ids


    This works with lspci and if it's outdated may not give you the exact manufacturer and device model. For example take these 3 different RX 580's: 1a:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Device 67df (rev e7) 1b:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Device 67df (rev e7) 1d:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Device 67df (rev e7) You ca........

  • Linux bash script to see what connected computers respond to ping


    A great way when moving your equipment to a new location, new router/switch etc to help confirm what MAC has what IP: for ip in `arp -na|awk '{print $2}'|sed s/(//g|sed s/)//g`; do echo ping $ip ping -c 1 -w 1 $ip > /dev/null if [ "$?" == 0 ]; then echo "$ip UP" fi done........

  • ffmpeg Linux Mint download, compile and install howto


    #if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2 tar -jxvf ffmpeg-3.3.2.tar.bz2 cd ffmpeg-3.3.2/ ./configure --disable-yasm install prefix /usr/local source path ........

  • Centos 7 A start job is running for dev-mapper-clx2droot.device (8min 44s / no limit)


    This error is usually because of some sort of encryption in this case a Seagate enclosure with encryption (even though not enabled) did not allow this hard drive to boot.........

  • USB 3.0 External HDD Enclosure Seagate UAS problems - [sdd] tag#1 CDB: Write(16) 8a 00 00 00 00 01 70 04 08 68 00 00 00 08 00 00


    This is a 8TB Seagate external USB 3.0 device apparently newer kernels use a module called "UAS" instead of "USB Storage" which causes issues as a lot of devices are not properly supported in UAS mode by the kernel driver. The solution some say is to disable UAS specifically for your USB device but I'd rather just disable UAS altogether. Solution blacklist UAS: *do not do this it does not work and just causes your USB 3.0........

  • USB 3.0 PCI x1 Card Review VIA VL805 on Linux Review and Experience


    This is a VIA made VL805 USB 3.0 Chipset with 4-ports and MOLEX powered. First of all this unit was cheap at about only 9 USD with fast shipping. My biggest concern was if this was a quality unit and would it really give you full USB 3.0 speeds (some people reported with similar cards that for some weird r........

  • USB Device/MP3 Player not working properly and can't browse the device filesystem? Check the cable twice and again!


    Here is a simple MP3 player and now there's a reason to understand why the supplied cable has some kind of capacitor and is very short. These devices can be VERY finicky and any voltage fluctuation or difference is enough to cause issues. Take for example the error messages from Linux Mint: [804829.895414] usb 1-1: USB disconnect, device number 11 [806961.109030] usb 1-1: new high-speed USB device number 12 using xhci_hcd........

  • Openshot 2.2 is very unstable always crashing in Linux Mint 18.1!


    Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Missing folder chosen by user: Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Removed missing file: MAH02949.MP4 Jun 1 15:45:57 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: ui_util:WARNING Icon theme media-playback-start not found. Will use backup........

  • Coolermaster CM Storm Enable LED Backlight in Fedora/Ubuntu/Mint Linux Howto - MB24 Keyboard and MS2K Mouse


    Just type the following in the bash/terminal shell to enable the blue LED light on the Coolermaster CM Storm keyboard: xset led 3 To make it automatic and permanent execute the following as root: echo "xset led 3" >> /etc/rc.local This is a fairly nice gaming keyboard whichI bought because I type very quickly and the cheap standard keyboards simply can't keep up!........

  • forcedeth MCP55 Nforce3600 Nvidia Network NIC Card Not working in Linux at 1gigabit speeds


    Now many people report this card simply not working in various Linux distros and kernels. My issue is different, it always works at 100mbit (eg. plugged into a 100mbit switch) but no matter what 1000M/gigabit switch I would try, it would never work. The link would be up (the lights were on) and the OS detected the link as being up as well but it wouldn't work at all and could not pass data in or out (not even a ack/ping). There is one simple solution and command........

  • Cannot Read License File cPanel Solution


    This can happen because port 80 is not open, or your license has expired and/or your IP is out of date and also if the license server itself from cPanel is having issues. In most cases as long as you have a valid license the following command will solve it: /usr/local/cpanel/cpkeyclt Updating cPanel license...Done. Update succeeded. Building global cache for cpanel...Done Cannot........

  • Nvidia Linux Card not working due to LSI 9200/SAS2008 IRQ conflict


    At first my BIOS said the card may not work right because there is no more option ROM space. I disabled the Option ROM for both LSI 1068 and 2008 chipsets, Network Boot ROM and most other PCI slots, Serial Port, etc... and the message went away but the card still does not work properly. But it still cannot initialize the card properly(does not work): [ 33.943272] NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:........

  • Linksys E2500 DD-WRT Upgrade Instructions and Enabling 5ghz with Tomato Firmware


    1.) Flash directly to this file: http://tomato.groov.pl/download/K26RT-N/build5x-132-EN/Linksys%20E-series/tomato-E2500-NVRAM60K-1.28.RT-N5x-MIPSR2-132-Max.zip *I was never able to get the larger "Mega" file to work, at least not initially so I recommend the file above. To enable 5ghz I had to do the "Clear NVRAM" Option before it was shown. 2.) Or if you don't need 5ghz (most devices do not support it and cannot........

  • Linux Mint/Ubuntu/Debian Dual NICs networks problem when enabling and disabling one device


    The Scenario You have dual NICs and you disable NIC1 which uses 192.168.1.1 as its gateway. With NIC2 you enable it/connect it to another network which also has the gateway 192.168.1.1 Everything will work fine at this point. When switching back to NIC1 even with NIC2 disabled and even unplugged, the OS basically can't pick up the new/updated ARP entry of the old device for 192.168.1.1 and perhaps thinks it is a security risk or spoof of some sorts and blocks i........

  • Linux Mint Network Manager Connection Disconnect Option Grayed Out


    This is a real pain because I had to manually unplug ethernet cables for network testing or to use an alternate network or guarantee physical access to one network segment is cut off. For some reason this happened after Ikilled dbus because it was confused and blocking packets thinking they were coming from the wrong interface since eth0 and eth1 both had the same subnet and gateway. I eventually did a "service network-manager restart" but the option was........

  • Linux Debian/Ubuntu/Centos How To Force Internet Traffic Through PPTP L2TP OpenVPN Account Only


    The following assumes the computer is local/physical to you and/or it always has a LANIP so it can be accessed on site without having a default gateway. The key to this is not to set a default gateway for your computer or you can set a script on boot or other time to delete the gateway (where eth0 is the NIC you are using): route del default eth0 50.80.20.2 is the VPN server you connect to 192.168.1.1 is your........

  • Avocent 8020 KVM Java Icedtea Viewer


    This command in Debian/Ubuntu/Mint will get everything need installed for most Java based KVM viewers: sudo apt install icedtea-netx The following additional packages will be installed: ca-certificates-java icedtea-netx-common openjdk-8-jre openjdk-8-jre-headless It seems every other updated version of Java or Icedtea breaks things and I will save the frustration of Java for another post.........

  • openvz yum problem Centos 6.5 cannot find file on mirror:


    #solution Edit /etc/yum.repos.d/openvz.repo For the first two entries comment out #mirrorlist and uncomment #baseurl and then it worked openvz yum problem Centos 6.5 cannot find file on mirror: yum update Loaded plugins: fastestmirror Determining fastest mirrors * openvz-kernel-rhel6: mirrors.ustc.edu.cn * openvz-utils: mirrors.ustc.edu.cn base ........

  • Installing zoneminder on Ubuntu/Debian Linux Howto


    sudo apt-get install zoneminder [sudo] password for one: Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: libuser-perl python-evince kdebase-apps kwrite unixodbc libgnomeprint2.2-data python-soappy vgabios python-metacity hddtemp python-mediaprof........

  • Dell CS24 NV5/NV7 Gigabyte GA-3CESL-RH Motherboard ROM Chip info


    If you remove the white label on the chip (near the CMOS battery) you will find the following details about it: SST 49LF080A 33-4C-NHE It is the PLCC32 type and can be pried and removed safely (but be very careful) with an eye glass flat head screw driver. If you just have a bad flash you may be able to reprogram your original or just buy another one with the part# above and reprogram it. This is great news for people who have bricked th........

  • HP Procurve Switch 2824 CLI Telnet Experience , Guide and Tutorial


    ------------------------------------- ProCurve J4903A Switch 2824 Software revision I.10.77 Copyright (C) 1991-2009 Hewlett-Packard Co. All Rights Reserved. RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by the Government is subject to restrictions........

  • Dell CS24-NV7 lspci dmidecode info


    0000:00:00.0 RAM memory: NVIDIA Corporation MCP55 Memory Controller (rev a2) 0000:00:01.0 ISA bridge: NVIDIA Corporation MCP55 LPC Bridge (rev a3) 0000:00:01.1 SMBus: NVIDIA Corporation MCP55 SMBus (rev a3) 0000:00:02.0 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a1) 0000:00:02.1 USB controller: NVIDIA Corporation MCP55 USB Controller (rev a2) 0000:00:05.0 IDE interface: NVIDIA Corporation MCP55 SATA Controller (rev a3) 0000:00:05.1 I........

  • Dell CS24,FS12 NV5 and NV7 1U Server Information & Parts


    Motherboard: Gigabyte GA-3CESL: http://b2b.gigabyte.com/products/product-page.aspx?pid=2658#dl Dell Part Numbers for the motherboard: R1232 R1232L R2232S SERVER MOTHERBOARD GENUINE 408P9 CN-0408P9 GA-3CESL Manual Download here RAMSlots: 16 (8 controlled by each CPU) RAMType: DDR2 ECC 5300P........

  • Error: Cannot retrieve metalink for repository: epel. Please verify its path and try again


    Error: Cannot retrieve metalink for repository: epel. Please verify its path and try again You have to upgrade the ca-certs for epel but need to disable it before that can happen. yum upgrade ca-certificates --disablerepo=epel........

  • Dell CS24SC Server Info


    Dell CS24SC Info 0000:00:00.0 Host bridge: Intel Corporation 5100 Chipset Memory Controller Hub (rev 90) 0000:00:02.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x8 Port 2-3 (rev 90) 0000:00:03.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x4 Port 3 (rev 90) 0000:00:04.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x16 Port 4-7 (rev 90) 0000:00:05.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x4 Port 5 (rev 90)........

  • Dell CS10-F1D Server Info lspci Linux specs


    0000:00:00.0 Host bridge: Intel Corporation 5000P Chipset Memory Controller Hub (rev b1) 0000:00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 (rev b1) 0000:00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 (rev b1) 0000:00:04.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 (rev b1) 0000:00:05.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4........

  • Wordpress Plugin manual install how-to


    This is the most secure way since we don't know if using the built-in ftp method of Wordpress is secure (that is do they store, record or transmit the ftp login information to a third party like the NSA?). Upload or wget the plugin and then unzip it from the Wordpress website tot he following path of your wordpress: /yourwordpressinstall/wp-content/plugins Then navigate to the "Plugins" section on the left side o........

  • Centos automatic ifcfg-eth0 scripts based on list of IPs from bash


    It's a basic script that reads the file "ips.txt" in the current directory and then creates a corresponding ifcfg file     #!/bin/bash GATEWAY=192.168.1.1 NETMASK=255.255.255.0 device=eth0 counter=0 for ips in `cat ips.txt`; do........

  • How to root and unlock S4 in Canada Bell/Rogers/Telus/Fido I337 4.4.2


    i337 Canada on Bell is hard to root or even install TWRP Installed TWRP from Odin and my computer gave me the bluescreen at the end but it seemed to be successful (after ODIN said reset). TWRP mode does not seem to enter, instead you get the Android recovery mode with Volume up + Home http://galaxys4root.com/galaxy-s4-root/how-to-root-att-or-verizon-galaxy-s4-on-android-4-4-2/ 1.)........

  • Postfix how to secure outgoing authenticated e-mails for privacy and hide the IP address, mailer and other things


    The most common solution is to use the /etc/postfix/header_checks but this is a big problem. Why is header_checks a problem? Because it does it to all mail whether incoming or outgoing and whether authenticated or not. We of course want as much header information for incoming as we can get for many reasons but many organizations want to secure and make their mail clients as secure as possible. I adapted this solution to the client's custom config, they are configur........

  • Samsung Galaxy Note Upgrade/Update Experience from 4.0.4 with aftermarket ROMs


    It really seems that 4.4.4 is not ready or stable for the i717 yet and this makes sense since it takes a lot of work/development and testing to get the factory stock ROMs working well. In the end I used the 4.1.2 based Blackstra BlackJelly because it was fast, stable and just works and feels great. The aftermarket support is great but many devs are focussed on adding features and customization that most of us don't want or need rather than getting things smooth and stable.........

  • CPanel Link to all of the command line options


    CPanel says you can access 98% of the functions through CLI which experienced Unix/Linux admins prefer for simplicity and for scripting.  I've never found CPanel easy to use from the admin panel, it seems everything is hard to find and a simple task becomes a series of hunts. So for people like me here's the list: http://cpanel.net/system-administrators/command-line-scrip........

  • error: Legacy syntax is unsupported: copyright error: line 10: Unknown tag: Copyright: distributable


    Usually just modify the .spec file to resolve this: vi specfile.spec Change "Copyright: GPL" to "License: GPL" and try again.........

  • yum Centos 386 and 64 bit conflict resolution


    This can happen when you install RPMForge or other repos with the wrong architecture and here's how you fix it (simply uninstalling won't usually fix it): solution yum clean all yum -y install openvpn Loaded plugins: fastestmirror, presto Loading mirror speeds from cached hostfile * base: mirror.its.sfu.ca * extras: centos.mirror.nexicom.net * rpmforge: mirror.cpsc.ucalgary.ca * up........

  • Asterisk iptables block bruteforce attacks howto with fail2ban


    yum -y install fail2ban vi /etc/fail2ban/jail.conf [asterisk-tcp] enabled = true filter = asterisk action = iptables-multiport[name=asterisk-tcp, port="5060,5061", protocol=tcp] sendmail-whois[name=Asterisk, dest=you@example.com, sender=fail2ban@example.com] logpath = /var/log/asterisk/messages maxret........

  • Linux free space not reclaimed after deleting large log file solution


    This example involves an Aterisk message log of about 26GB, but with any server it usually does not get deleted until the server is stopped/restarted: asterisk 13729 root 6w REG 0,41 27277943090 59097971 (deleted) /var/log/asterisk/messages So if you've deleted a bunch of large logs, make sure you restart the server for them to regain your space. ........

  • CPanel suhosin install failed


    /scripts/phpextensionmgr install PHPSuHosin Updating md5sum list Fetching http://httpupdate.cpanel.net/cpanelsync/easy/targz.yaml (connected:0).......(request attempt 1/12)...Resolving httpupdate.cpanel.net...(resolve attempt 1/65)... Fetching http://httpupdate.cpanel.net/mirror_addr_list (connected:0).......(request attempt 1/3)......connecting to 74.50.120.123...@74.50.120.123......connected......receiving...100%......request success......Done........

  • Sendmail Gmail.com blocking


    relay=alt4.gmail-smtp-in.l.google.com. [74.125.136.26], dsn=4.0.0, stat=Deferred: 421-4.7.0 [ 10] Our system has detected an unusual rate of This is strange because the mail server IP is not blacklisted anywhere and the IP itself has not been used for years and this server is clean and has only sent a few e-mails to gmail.com in its entire time. I wonder if this is a legacy block on a whole range of IPs as punishment for others in the block........

  • Dell FS12-NV7 2U Server Information and Guide


    I've got one of these for testing projects from work at home and got more than I bargained for with the time I've spent on it due to the storage handing/Perc 6/i cards. My particular model came with the following: 2U Rack Mount Server with Rails 2xOpteron 2373 EE (Quad Core, there is a 6-core version that can be found at times) 16GB RAM 2 x 250GB Seagate SATA 2 x Dell Perc 6/i (horrible and a nightmare to work........

  • Dell Perc 6/i SATA benchmarks without battery


    The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results. This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane. Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: N/A De........

  • Dell Perc 6/i Restore BIOS/Bricked Solution Guide Howto


    I bricked one of my cards by following a guide from UNRAID. Step #1 from them wipes out the BIOS, but guess what? The step where you restore the BIOS should have been done first, which is sas2flash but no version supports or is able to find my Perc 6/i. So now I'm a bit stuck. I tried using megarec but it's funny that it can wipe the BIOS but can't forcefully reload it: megarec -writesbr 0 mpt2sas.rom Supports 1078 control........

  • Dell Perci 6/i Firmware Upgrade Guide Tutorial


    One thing to remember is that you need MegaCli to do the flashing. You also need the correct file,I tried at least 2 different Perc 6 firmwares from Dell that kept getting rejected as corrupt by MegaCli(they were really the wrong version). I have an external PCI-E Dell 6 Perc/I butI chose images from the 'Integrated" on motherboard version as it was allI could find. They are different, and below is my first time finding success.........

  • Dell Perc 6/i cannot downgrade


    I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally. I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN --2013-08-26 12:53:39-- http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN Resolvi........

  • LSI MegaRAID Adventures, Guide and HowTo


    LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........

  • yum update error


    yum update error Traceback (most recent call last): File "/usr/bin/yum", line 29, in ? yummain.user_main(sys.argv[1:], exit_code=True) File "/usr/share/yum-cli/yummain.py", line 229, in user_main errcode = main(args) File "/usr/share/yum-cli/yummain.py", line 145, in main (result, resultmsgs) = base.buildTransaction() &nbs........

  • WD 20EARX Dead Again


    Another new drive bad from the start: Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........

  • init: tty (/dev/tty2) main process (1031) terminated with status 1 init: tty (/dev/tty2) main process ended, respawning


    After some fsck issues I can't boot my Centos 6.4, this just keeps repeating over and over. init: tty (/dev/tty2) main process (1031) terminated with status 1 init: tty (/dev/tty2) main process ended, respawning Disabling SELinux through Single User mode fixed this.........

  • Country List Names in HTML Select From


    This is useful for developing a lot of applications, I'm putting it here to keep it handy for myself and hopefully others: Choose CountryCanadaJapanUnited StatesUnited KingdomAfghanistan........

  • SSH Can't Login/Hang


    Client Log OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to 192.168.1.253 [192.168.1.253] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type 1 debug1: identity file /root/.ssh/id_d........

  • Samsung Galaxy Note I717M Canadian Version, Root and Unlock


    I chose this because I heard a lot of stories about scams and that many providers I contacted said they can't unlock the Canadian I717s (one said "my Bell server" is down). This method worked perfectly on my Bell I717M and should work for all I717 in Canada, I was able to insert a foreign SIMcard. This will work abroad too but remember entering CWM mode is different for I717's in other countries (at least theUS). Step 1 - Root + CWM........

  • Samsung Galaxy Note ICS Corrupting microSDHC partition table?


    This was partitioned as a single 32GB VFAT but when I inserted it into the phone it said that it can't read it and now here is how the partition table looks. Interestingly enough the data works and reads fine from the computer still. Disk /dev/sdb1: 32.1 GB, 32085360640 bytes 64 heads, 32 sectors/track, 30598 cylinders, total 62666720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum........

  • Centos 6 RTL8111/8168B r8169 link up and down error solution/fix


    02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) For whatever reason it seems the r8169 driver that ships and has shipped with most Linux distros for years is still flawed and does not work properly on these cards, causing 100mbit connectivity when it should be 1gbit and even worse, causing random network dropouts. The r8169 driver in Linux kernels is simply not meant to be used on th........

  • Samsung Galaxy Note Ubuntu Linux USB Connection Error


    This pops up when connecting the phone and it doesn't seem to charge. The phone keeps showing a status message every few seconds "Connected as a media device". It's ridiculous why this phone doesn't just default as a simple USB Mass storage device. Here's what I see in /var/log/messages: Jan 30 18:51:27 QuadCoreAM2 kernel: [18038228.144046] usb 1-3: new high speed USB device using ehci_hcd and address 24 Jan 30 18:51:28 QuadCoreAM2 ke........

  • kvm cannot boot xen guest using lvm


    This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel. I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk. I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one). This is strange but it seems like this Xen PV guest has some sort of hidden or........

  • lvm resize and use the remaining extra space


    df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_12-lv_root 50G 1.2G 46G 3% / tmpfs 7.8G 0&nb........

  • Thunderbird How-To Copy/Backup/Restore Accounts and Settings to Another Computer


    The best way is to use rsync, I've set it up so it doesn't copy unnecessary files, or at least ones I'm sure aren't needed. Here is the rsync command Iused (adapt to your specific Thunderbird profile location): rsync -hazv user@remotehost.com:/home/user/.thunderbird/sbrer.default/* /home/user/.thunderbird/4nyb0.default/ --exclude=global* --exclude=Cache --exclude=ImapMail --exclude=Mail This is a great way to get your e-mail accounts going on a new c........

  • postfix how to send to multiple recipients default limit of 1000


    The size of the message you are trying to send exceeds a temporary size limit of the server. The message was not sent; try to reduce the message size or wait some time and try again. The server responded: 4.5.3 Error: too many recipients. We set this in main.cf: smtpd_client_recipient_rate_limit=0 We didn't specify it before and the default is said to be 0/unlimited and it still didn't change anything.........

  • Samsung Galaxy Note Upgrade to ICS 4.0 microSDHC card not detected/dataloss after upgrading - possible solutions


    I backed up everything in the /mnt/sd_card directory thinking that some dataloss could occur for some reason but purposely left my microSDHC unbacked up thinking that "it won't touch that since it's external" and Samsung's and other manufacturers website even say this (that it won't be affected and not to worry etc). Apparently I was wrong, my microSD was "undetected" and asked to be formatted after the upgrade (there goes 3-months worth of family photos). No........

  • Windows Secret Hidden Temp Directory to free out of disk space issues


    Replace "Administrator" with your username. C:Documents and SettingsAdministratorLocal SettingsTemp Ihave often found several gigabytes of temporary files in there! Just be warned that they may not all be deletable if the files are being used by open programs (so close everything you can). This helped me in a pinch many times when for apparently no reason gigs of disk space are being used for an unknown reason.........

  • HowTo Migrate and Import iPhone/Outlook Contacts into Android without using GMail using .vcf files


    I searched for days after getting my Galaxy Note and couldn't find a way to do this (at least not without buying programs for either Android/Windows). All I read was ways to sync and import the contacts to GMail but I don't want to use GMail for privacy reasons. GMail/Google steal all of your personal information and use it for whatever purposes they want to and may sell or release it to who knows where (I don't care what their policy says but this stuff happens), just like the default........

  • Asus VE247H 23.7" Inch LCD/LED Backlit Monitor Dead/Stuck Pixel Policy Complaint


    I've thought for awhile that Asus has been banking on its years old reputation for quality amongst gamers and enthusiasts and I think I'm right. My Asus VE247H Monitor with a supposed 2MS refresh rate has 1 red/stuck/dead pixel but fortunately it can only be seen on a non-true black picture or against a blue screen. I have several Asus products and find they're all of fairly poor quality. First of all their motherboards have given me the most issues of any brand, they te........

  • Ubuntu 10.04 Flash Videos have tearing/lines Solution


    This is what I call a ridiculous bug in compiz that causes it. The solution/To fix it just install "compizconfig-settings-manager" Open it up and Navigate to General Options -> Display Settings Set the "Refresh Rate" to the current refresh rate of your monitor. For ATI cards with slow window dragging/response supposedly disabling "Sync to VBlank" fixes that but otherwise leave it as is.........

  • Openvz YUM Error Solution to "[Errno -1] Metadata file does not match checksum Trying other mirror."


    It's weird because I have a nearly identical box and setup and I can update the ovzkernel-PAE* just fine but on this box it doesn't work. I only get this error with the openvz.repo and not others such as Centos-Base.repo With my other server it works normally: ================ Setting up Update Process Resolving Dependencies --> Running transaction check ---> Package ovzkernel-PAE.i686 0:2.6.18-238.12.1.el5.0........

  • Purolator Tracking "PLEASE CALL 1 888 SHIP-123 OR 1-888-744-7123 FOR INFORMATION ON THIS SHIPMENT."


    TRACKING DETAILS PIN xxxxxxxxxxx Status PLEASE CALL 1 888 SHIP-123 OR 1-888-744-7123 FOR INFORMATION ON THIS SHIPMENT. I know this is not really tech related but Iorder a lot of hardware on-line these days and once I had a delivery by Purolator. I didn't get anyone on the phone at Purolator after a few minutes so I gave up, but it turns out that the person on the phone or the system will tell you to........

  • Apache High CPU Usage Enable Mod_Status Guide Solution - Find Cause of High CPU Usage Script/Domain


    mod_status is a great way to track down the source of high CPU usage and to find what vhost/script is the cause of it. It gives you a live view of bandwith usage, CPU usage, and memory usage broken down by domain/vhost and script/URI. Enable mod_status vi /etc/httpd/conf/httpd.conf ExtendedStatus On SetHandler server-status Order Deny,Allow Deny from all All........

  • Upgade VBOX/Virtualbox 3.2 to 4.0 in Linux


    I was afraid to remove the virtualbox 3.2 package in Ubuntu because I didn't know if it might remove the .virtualbox folder which contains all of my VM data. I have a backup soI did remove the package and found everything was intact, so I installed and upgrade to VBOX 4.0 which seems to be a huge improvement, especially in UI performance.........

  • 2011 Best Laptop - HP 15.6" Laptop featuring AMD Athlon II P340 Processor (G62-420CA)


    My mother needed a new laptop and I recommended her the same one I would have bought myself or my wife, that means the cheapest possible laptop with the most features for the money. This HP shines at this price point and one thing that made me stay away from buying more and recommending HP/Compaq was the poor battery life. Not anymore, this model has an industry leading up to 4 hours of battery life. Key Factors for Choosing It: HDMI Out........

  • pgina can't login after installing


    After Installing pgina I couldn't login to Windows anymore with my blank password Administrator account! An unknown error has prevented your account from being created.nrThis may be due to policy or security settings as well as other machine configuration.nrPlease consult your administrator. Hit F8 to start Windows in Safe Mode and you can login normally and then remove PGina, it shouldn't cause this problem or behavior out of the box.........

  • Yahoo Mail (email) DNS Server Out Of Date Problems


    I don't expect this to be solved soon but some of Yahoo's DNS servers are out of whack. I changed the IPs of some nameservers of some domains and now most Yahoo users can't e-mail to those domains! As you can see below by the "No MX or A records for mychangedomain.com", now Yahoo's DNS/mailserver DNS cache is wrong. You would think they would at least have cached the old incorrect records, but instead for some reason their DNS cache has no entry and doesn't seem........

  • 95th Percentile Billing vs Usage Billing, what's better?


    There are all kinds of threads and links on the internet, and this seems to be a contentious issue butI don't know why. 95th percentile is either a good deal for some or a big rip off for others, Ijust said it there :) But the reality is that for MOST people who transfer low amounts of data but burst to higher speeds such as 40mbit+ even for short periods of time, then you'll pay a lot of money to do that. Basically 95th percentile is an-old archaic method........

  • Linux - mptbase/MPT Fusion LSI Logic Error mptbase: ioc0: ERROR - didn't initialize properly! (-1)


    kernel 2.6.27.54 Fusion MPT base driver 3.04.07 Copyright (c) 1999-2008 LSI Corporation Fusion MPT SPI Host driver 3.04.07 mptbase: ioc0: Initiating bringup mptbase: ioc0: WARNING - Unexpected doorbell active! mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000001! mptbase: ioc0: ERROR - Diagnostic reset FAILED! (102h) mptbase: ioc0: WARNING - NOT READY! mptbase: ioc0: ERROR - didn't initialize proper........

  • Linux Realtek Gigabit NIC huge/high latency problem after sleep?


    That is pinging to the gateway IP on the same switch, the same IP is pingable externally without any problems which makes me think the switch is fine. 64 bytes from 55.55.55.55: icmp_seq=4 ttl=255 time=1.07 ms 64 bytes from 55.55.55.55: icmp_seq=1 ttl=255 time=3536 ms 64 bytes from 55.55.55.55: icmp_seq=2 ttl=255 time=2536 ms 64 bytes from 55.55.55.55: icmp_seq=3 ttl=255 time=1536 ms 64 bytes from 55.55.55.55: icmp_seq=8 ttl=255 time=1.20 ms 64 by........

  • md: data-check of RAID array md3


    This really made me nervous but notice the mdstat says "check". This is because in Ubuntu there is a scheduled mdadm cronscript that runs everyday on Sunday at 00:57 that checks your entire array. This is a good way because it prevents gradual but unnoticed data corruption which Inever thought of. As long as the check completes properly you have peace of mind knowing that your data integretiy is assured and that your hard drives are functioning properly (I'........

  • Dying Seagate 7200.11 SD15


    [137392.910057] ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x80000 action 0x6 frozen [137392.910077] ata4: SError: { 10B8B } [137392.910095] ata4.00: cmd 60/20:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 16384 in [137392.910099] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [137392.910122] ata4.00: status: { DRDY } [137392.910135] ata4: hard resetting link [137393.440060] ata4: SATA link........

  • yum in Centos 5/Xen halts and exits suddenly


    yum exits in the middle The problem is this VPS seems to be an OpenVZ template from HyperVM. The only way to make it work was to disable i386 packages since this was an x64 kernel. That shouldn't be necessary but it was the only way to make yum stop quitting after the first package or two. I couldn't find any issue by checking the logs either. echo y|yum install vim-minimal telnet expect jwhois net-tools slocate iptables elinks gawk L........

  • WD (Western Digital) Advanced Format Drive Lagged/Slow Speed/Performance/Design Flaw EAD/EARS problem WDC WD20EARS-00S8B1


    Let the numbers speak for themselves, from what I read the Load_Cycle_Count which is very high (more than 500,000/half a million times) is the number of head parks. What a stupid"Green" design and design flaw which will probably mean an early life for the drive. This is almost as silly as Seagate's new reputation for BSY/poor quality disks since the 7200.11 series. To make it worse this is also when Western Digital introduced "Advanced Format" o........

  • PHP CURL SSL won't work or connect


    I spent so much time debugging this, most sites don't tell you a very important option to use with CURL and you will only find out this is the problem by running the PHP script from the command line you get the following output that shows the issue (I don't see any way to get this output from Apache itself). * About to connect() to ip.ip.ip.ip port 25000 * Trying ip.ip.ip.ip... * connected * Connected to ip.ip.ip.ip (ip.ip.ip.ip) port 25000 * succes........

  • Linux How To Add/Delete A Default Route/Gateway


    Remember to replace "eth0" with your NIC device although usually it will be eth0. Replace 192.168.1.1 with your default gateway, remember you can also add multiple gateways by adding a second/different default gateway. route Kernel IP routing table Destination Gateway Genmask&nb........

  • Ubuntu Linux HTML Rendering left bracket < problem appears as 003C box


    In Ubuntu when quoting in a forum that would include a left < bracket it often appears garbled as a box with 003C inside. Also with phpbb anything inside the "code" field appears garbled and as gibberish. For some reason I can't find anyone else complaining about this and have not found a solution for it, but it's very annoying.........

  • Linux Kernel Freeze/Hang during boot on io scheduler cfq registered (default)


    You'll see the following and the boot process will freeze: io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) I have struggled with this issue on vari........

  • Ubuntu 10.04 Linux is still not ready for the Desktop world


    I am a huge fan of Linux and the idea of OpenSource but I've said it many times, there are still hurdles in today in 2010 for Linux as a Desktop. Linux is still intended for servers at its very core. This can be changed succesfully though, as Apple has shown us with Mac OS X based on FreeBSD. Half of the issue is lack of driver support and the other half is the Linux Kernel and Window Manages, KDE and GNome still both don't cut it (but they're getting closer). I'll........

  • GNOME/Ubuntu how to navigate without a keyboard


    The most basic is the start menu, which is accessed with Alt+F1........

  • Realtek r8169 1gbit/1000mbit NIC/Ethernet Goes Down/Halts on Large File Transfer/Heavy Network Usage


    This is obviously a bug in the r8169 kernel module and it seems to affect a lot of people. I upgraded to the latest kernel and hope this won't happen anymore, as it is a very serious error. This is especially serious for those who are running servers with this chipset, who can afford for the NIC to randomly go off-line for no apparent reason? [655548.189113] type=1505 audit(1277067560.902:5): operation="profile_load" name="/usr/bin/freshclam&q........

  • RAID 1 and Non-RAID Hard Drive Performance Comparison using tiobench


    Here is a RAID 1 partition (500GB Seagate & 2TB WD): Sequential Reads File Blk Num Avg Maximum Lat%&nbs........

  • FUSE/Curlftpfs mount ftp account as drive partition in Linux


    This is a great way to use your ftp server space, for example on your web hosting account (althoughI believe many hosts don't allow storage like this), but if you have a VPS/Dedicated Server etc.., this would be perfect. Imagine how easy it is to work with an ftp account that you can just mount as a normal partition or directory in Linux, it would be great for backups etc.. Name curlftpfs - mount a ftp host as a local directory Synopsis........

  • How To Set DHCP/Static IP Address in Centos/RHEL/Fedora & Debian/Ubuntu/Kubuntu/MEPIS Set DHCP/Static IP Address


    Basically the two main types of distros are Debian and RHEL/Centos based. I'm just going to give a quick overview of how the configuration of IP interfaces works in Debian/Centos based distros. *Just one thing to remember, when setting IPs statically you have to manually specify a DNS server in /etc/resolv.conf (since DHCP is what normally does it automatically) Debian/Ubuntu/Kubuntu/MEPIS The IP (DHCP &........

  • Intel Corei5 750 Complaint/Onboard Video Issue on Intel H57 chipset not working


    Do you have an LGA1156 board and wonder why your onboard video isn't working? It's probably because there is no GPU integrated on the board itself, it is supposed to be on the CPU and new CPU's from Intel don't come with it! I was shocked to learn that you can buy a motherboard with onboard video which doesn't work. Inever knew it was being done or possible, but to make it worse the latest Core i5's don't have video on the die of the CPU. This means having on........

  • Gigabyte GA-H57M-USB3 Complaint Review/Comments


    I'm not impressed with this motherboard, I was impressed with my Gigabyte AM3 board which seems to work flawlessly. Everyone knows that the firmware is flawed, even though I have the F6, it still seems that the system doesn't reset properly or quickly enough. Another HUGE problem is that in most Linux kernels the NIC won't work (if you try 10 times by rebooting it might). I also notice that you need to power down for it to work. This board does not seem very com........

  • Unixbench Score on Core i5 750 with OpenVZ Kernel vs Xen/Openvz


    This was unbelievable how much the Xen kernel slows things down, keep in mind both tests were done on the hostnode, one was with the Openvz-Xen hybrid kernel and the other was just OpenVZ. You can see the performance difference is nearly 300% better when not using the Xen kernel. OpenVZ-Xen Kernel Test Results (I was wondering what was wrong/so slow with my Core i5!) # # # # # #&n........

  • Seagate Drive 500GB Drive Dying


    This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device........

  • Seagate 7200.11 firmware defect in 500GB, 1000GB (1TB) and 1500GB (1.5TB) Hard Drives


    Seagate Inventory/Firmware Check I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate. *Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate! Seagate Inventory/Firm........

  • Convert HDD/Hard Drive Partition(s) into non-RAID into RAID 1 using existing data without data loss and without reformatting.


    Before we start I take no responsibility for this, you should have a backup and if you make a mistake during this process you could wipe out all of your data. So backup somewhere else before starting this as a precaution, or make sure it's data you could afford to lose. The RAID 1 Setup (Hardware Wise) I've already setup my 2 x 1TB (Seagate) drives with identical partitions, make sure your new hard drive (the empty one) is setup like your curr........

  • email2fax and Asterisk to do eFaxing


    It's basically free bash shell script available from: http://wpkg.org/email2fax/index.php/Main_Page Make sure you have the required tools: libtiff ghostscript mpack/munpack Where you can e-mail your Asterisk box and it will fax it to the phone number in the subject line. The good news ends there, it is fairly undocumented and buggy. Take for example how the documentation mentions you can invoke from the com........

  • tar gzip: stdout: File too large - Error Size Limit on Large file > 17GB


    The folder I was trying to archive is about 72GB, but much like rsync at about 17GB it chokes because of the filesize. What's with so many common and essential Linux tools having such limitations? I guess it is likely that the authors never wrote their code with the idea that files would be so large but it's still very annoying. It's important to stay on top of these limitations on production servers because I didn't realize what happened until I checked the file with "........

  • Picking an FTPD (vsftpd) Server in Linux Centos/Debian


    I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find. yum search ftp Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * rpmforge: ftp-stud.fht-esslingen.de * base: mirrors.netdna.com * updates: updates.interworx.info * addons: yum.singlehop.com * extras: mirrors.netdna.com rpmforge........

  • Compaq V2405CA Laptop - Unixbench Performance Test


    Here are the results, it is Sempron 3000+ AMD Mobile, 500Gig HDD, 512MB RAM with shared ATI Radeon graphics. # # # # # # # ##### ###### # # #### # # # # ## # # # #&nb........

  • PHP cannot access /usr/bin/openssl


    PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist: [code:1:1fd0f3abbe] if (!file_exists($OPENSSL)) { //echo "ERROR: OPENSSL $OPENSSL not foundn"; }[/code:1:1fd0f3abbe] I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........

  • SSH automatic login without password


    SSH automatic login without passwordlocal> ssh-keygen -t rsa -f .ssh/id_rsa -t is the encryption type -f tells where to store the public/private key pairs. In this case, the .ssh directory on home is being used A password will be asked; leave this part blank, just pressing Now, go the .ssh directory, and you will find two new files: id_dsa and id_dsa.pub. The last one is the public part. Now, copy the public key to the serv........

  • Great sound tutorial


    Great sound tutorialThis is great if you need users to be able to start/stop playing sound on your page with the click of a button. http://www.smartwebby.com/Flash/sound_button.aspHere's a simple one except that it doesn't do rollovers. http://www.flash-here.com/tutorials/flash_play_sound.html I actually could not get the rollovers to work using the other tutorial so it is either a mistake on the webmaster's part or........

  • Setup Static IP Address ONBOOT


    Setup Static IP Address ONBOOTAssuming you are using eth0 Note this will work for any version of CentOS and basically any version of Redhat Linux or Redhat based distribution. You would need to create a new file [code:1:02f8d34c30] /etc/sysconfig/network-scripts/ifcfg-eth0:0[/code:1:02f8d34c30] DEVICE=eth0:0 the ":0" at the end specifies alias 0 we could actually change this to ":99" or "........

  • The New Chips on the Block


    The New Chips on the BlockThe New Chips on the Block By Bruce Gain Story location: http://www.wired.com/news/infostructure/0,1377,67795,00.html 02:00 AM Jun. 13, 2005 PT We have embarked upon a new era in x86 PC computing -- so say chip giants AMD and Intel following their launches of dual-core PC processors. So how will dual-core processing change your PC computing experience? Our FAQ should help you decide whether or when you sho........

  • Intel's Finnish Fetish


    Intel's Finnish FetishIntel's Finnish Fetish By Dave Mock June 13, 2005 Chipmaker Intel (NASDAQ: INTC) has successfully topped the personal computer market for decades. Breaking into related areas such as communications has been much difficult for the world's largest semiconductor maker. But a new partnership with Nokia (NYSE: NOK) could help to change that. Intel's forays into cellular-phone and home-entertaiment-device chips have........

  • Photogallery


    Photogalleryhow do you setup a dope photogallery with slide show and all?........

  • FreeBSD Desktop OSs


    FreeBSD Desktop OSsI would probably choose these over Linux. In many ways these are probably more stable and just as easy to use as any Linux distros but the benefit of stable, updated and secure packages! PC-BSD - http://www.pcbsd.org DesktopBSD - http://www.desktopbsd.net/index.php?id=37 Personally PC-BSD is Beta at this point and is not easy if you are installing it on a non-primary partition. I have not used Deskt........

  • Bash Script Info


    Bash Script Infohttp://www.faqs.org/docs/Linux-HOWTO/Bash-Prog-Intro-HOWTO.html#ss10.5 http://www.scit.wlv.ac.uk/~jphb/spos/notes/shell/shell5.html http://quong.best.vwh.net/shellin20/#LtohTOCentry-41 http://www.cactus.org/~dak/shellscript.html http://db.ilug-bom.org.in/Documentation/abs-guide/ http://pegasus.rutgers.edu/~elflord/unix/bash-tute.html http://heather.cs.ucdavis.edu/~matloff/UnixAndC/Unix/CShellII.html Since bash i........

  • Other Security Web Sites


    Other Security Web SitesSeveral websites actively track security issues. This list provides you with the major providers of security information on the Web. Many of these organizations also provide newsletters and mailings to announce changes or security threats: Center for Education and Research in Information Assurance and Security (CERIAS) CERIAS is an industry-sponsored center at Purdue University that is focused on technology and relate........

  • Clustering Links


    Clustering LinksI thought this might be interesting for people with spare time. [b:6423c19973]Great clustering article from Linux Mag[/b:6423c19973] http://www.linux-mag.com/2003-11/clusters_01.html [b:6423c19973]General Linux cluster information[/b:6423c19973] http://www.gdargaud.net/Hack/ClusterNotes.html#HighA http://www.faqs.org/docs/Linux-HOWTO/Cluster-HOWTO.html#s3 http://www.yolinux.com/TUTORIALS/LinuxClustersAndFileSys........

  • Load Balancing/Clustering


    Load Balancing/ClusteringAn interesting article that discusses the pros, cons and viability of load balancing/clustering http://www.wwwcoder.com/main/parentid/493/site/4189/68/default.aspx ZoneEdit seems to offer an interesting Fail Over Service as well: http://www.zoneedit.com/doc/faq.html#fo........

  • Wireless/xmit power - DD-WRT v23 SP2 (09/15/06) std - build 3932 Linksys WRT54G/GL/GS


    I played around with xmit power (how much power in mW) to see if I could increase the range and signal strength. Idon't think this Linksys WRT54G's strength is the wireless, it seems to have poor signal quality and transfer rates all around. Ithink part of the problem is also that there are several wireless networks around my house that could be interfering and the walls are thick here. Anyaway, moving on now :) The default is 28mW and I increased it to........

  • Linux Kernel Compilation (Intel(R) 82575/82576 PCI-Express Gigabit Ethernet support ) Error - drivers/net/igb/igb_main.c: In function `igb_up': make[3]: *** [drivers/net/igb/igb_main.o] Error 1


    Linux Kernel v2.6.30.3 102220 blocks CHK include/linux/version.h CHK include/linux/utsrelease.h SYMLINK include/asm -> include/asm-x86 CALL scripts/checksyscalls.sh CHK include/linux/compile.h CC drivers/net/igb/igb_main.o drivers/net/igb/igb_main.c: In function `igb_up':........

  • Create/Enable SSL Certificates for Apache on Linux/Unix Systems eg. Redhat,Centos,Debian


    Shortcut/Easiest Way To Create A Self-Signed Key: openssl req -new -x509 -nodes -days 1530 -out server.crt -keyout server.key Using the above, you instantly create a self-signed certificate valid for 1530 days and you can simply skip to step #5.) below. If You Need a Real SSLCertificate (eg. Equifax/Openssl) then you need to create a CSR request (you'll need to follow Steps 1.) and 2.) in order to create the CSR. You then upload the CSR Certi........

  • Hard Drive Not Working/Not Detected By Your BIOS Anymore?


    I was starting to panic because suddenly my 1TB Seagate SATA drive wasn't working,I thought it was a BIOS issue because it seemed to have happened after I tried overclocking my Desktop too much. I tried powering down and waiting, but I still couldn't hear the drive spin up at all. I tried a second 1TB hard drive and it wouldn't work either. I checked all power connections again and again until one of the pins in the MOLEX connector popped completely loose. Th........

  • Clustered/Distributed Network Filesystems, Which Ones live up to the hype?


    I've tried to find a good sensible solution to cluster with and each technology has it's pros and cons and there is no perfect solution and I've found a lot of "exaggerations" in the applications, benefits and performance of these different filesystems. DRBD I first started off with DRBD and Ihave to say it does live up to the hype, is quite reliable (although it can be annoying to match up the kernel module and user applications since they must match and whe........

  • Tyan S2735-8M Maximum Hard Drive Limit/Not Working/Doesn't work with 1TB 1000GB hard drives


    Inever saved any of the logs, but basically no matter what OS (Linux)I used, I could not get my 1000GB hard drive to work (Seagate SATA). The BIOS recognizes the drive and fdisk -l shows the hard drive as it should. The tricky thing is that different OS's will give you different results, but don't be fooled. You can't use these larger drives for long. Iwas getting all kinds of seek/IOerrors and also messages that the port could not be read.........

  • Timezone Change/Updated for Linux/Unix Debian/Fedora/Ubuntu/Centos Change Update Time zone


    In Newer Linux Distros This Way Is Easiest and works on newer versions like Ubuntu, Mint, Fedora, Centos, Debian etc. #if you are missing timedatectl this in newer distros like Ubuntu/Mint/Debian and are using a container like Docker then do "apt install systemd" timedatectl set-timezone America/Vancouver Replace the America/Vancouver with the correct timezone. To see the list you can just type "timedatectl set........

  • iPhone Complaint Lock/Standby Disrupts WiFi and uses 3G instead


    Has Apple tried to give a golden egg to the cell phone companies? Has anyone noticed that if you set your lock time to x minutes, the phone doesn't just lock, it goes into standby. When it does this, any WiFi connection you have gets dropped and all push/data functions such as e-mail checking are done through the 3G network. There is no way to change this feature and functionality and it's very annoying, especially if you are downloading something or loading files over the........

  • iPhone 3GS 32GB "Harsh Review"


    Yes, Iadmit I finally got bitten by the hype as much as I can usually see through it all. Keep in mind this review is of the "stock" phone, no jailbreaking yet which is what really unleashes the customizability and whyI bought iPhone. I had better things to say about this phone before buying it, and it is a great phone, perhaps the best on the market by far, if not because of the Mac OS port onto the iPhone and all the apps, etc, etc. With that said........

  • Apple iPhone 3GS and predecessors are leading a revolution


    As much of a computer nerd as Iam, I'm usually a late adopter to technology for a few reasons. Ifeel most new hyped technologies and electronics are mainly fads, and I'm also cheap. Adopting later means you avoid the bugs, kinks and most importantly pay the lowest price, that's me being cheap again :) I never read much about the iPhone but Isaw all the hype around it and until recently I wasn't a big fan of anything Apple until a few years ago I realize........

  • Nokia N97 review, feedback and complaints


    I've had an old Blackberry for a few years and I was ready to spend some serious cash on a nice Nokia. I love the idea of the Linux based Symbian S60 OS, so I was looking at phones like the E63, E71 (both are basically the same, at least CPU/screensize although E71 is thinner, has a 3MP camera, has GPS, and has dedicated buttons to adjust the volume). Then Iheard about the N97 and what a revolution it was supposed to be and it was even compared to iPhone. To........

  • RTL8111/8168B R8169 Gigabit Link slow speeds


    This is the Intel Atom 330 motherboard with integrated Realtek Gigabit NIC (Intel Desktop Board D945GCLF2 Motherboard W/ Atom 330 1.6 GHz Dual Core Processor - Mini-ITX) I cannot achieve more than 15 MB/s, even doing a local transfer through eth0 to it's own IP. 100% 95MB 15.9MB/s 00:06 So this is not a cabling, switch or hardware issue, it seems like a driver or chipset limitation problem. Here is my........

  • OCFS2 crash


    When trying to even cd or ls the mounted OCFS2 partition it crashes. Ithink this is a combination of VMWare Server's problem and the way I mounted and symlinked to it. More than anything this shows the problem and lack of forsight with VMWare, but also that OCFS2 is easily crashed if you do strange things. Output of /var/log/messages for OCFS2 Apr 10 15:57:45 localhost kernel: [84331.691258] Modules linked in: vmnet vmci vmmon ocfs2_stac........

  • BASH script error "((: 08: value too great for base (error token is "08")"


    ((: 08: value too great for base (error token is "08") Here is the code that caused it for ((track=1;track ........

    • Latest Articles

  • FreePBX 17 How To Add a Trunk
  • Docker Container Onboot Policy - How to make sure a container is always running
  • FreePBX 17 How To Add Phones / Extensions and Register
  • Warning: The driver descriptor says the physical block size is 2048 bytes, but Linux says it is 512 bytes. solution
  • Cisco How To Use a Third Party SIP Phone (eg. Avaya, 3CX)
  • Cisco Unified Communication Manager (CUCM) - How To Add Phones
  • pptp / pptpd not working in DD-WRT iptables / router
  • systemd-journald high memory usage solution
  • How to Install FreePBX 17 in Linux Debian Ubuntu Mint Guide
  • How To Install Cisco's CUCM (Cisco Unified Communication Manager) 12 Guide
  • Linux Ubuntu Redhat How To Extract Images from PDF
  • Linux and Windows Dual Boot Issue NIC Won't work After Booting Windows
  • Cisco CME How To Enable ACD hunt groups
  • How to install gns3 on Linux Ubuntu Mint
  • How to convert audio for Asterisk .wav format
  • Using Cisco CME Router with Asterisk as a dial-peer
  • Cisco CME How To Configure SIP Trunk VOIP
  • Virtualbox host Only Network Error Failed to save host network interface parameter - Cannot change gateway IP of host only network
  • Cisco CME and C7200 Router Testing and Learning Environment on Ubuntu 20+ Setup Tutorial Guide
  • Abusive IP ranges blacklist
    • Copyright © realtechtalk.com 2024