apt install tftpd-hpa
#change TFTP_ADDRESS to by setting address to 192.168.1.1:69 or the IP you need, otherwise it will listen on all IPs and interfaces which could be a security risk.
# edit /etc/default/tftpd-hpa
TFTP_USERNAME="tftp"
TFTP_DIRECTORY="/srv/tftp"
TFTP_ADDRESS="192.168.1.1:69"
TFTP_OPTIONS="--secure"........
This can break things easily in remove environments where it was normally easy to convert a normal eth0 to a bridge under br0, and that bridge would normally have the same MAC address by default, which is desirable for most situations.
In Debian 11 this is different for some reason now.
https://unix.stackexchange.com/questions/681013/bridge-gets-random-mac-........
Assign way more replicas than you have of memory on all nodes and watch the Swarm crash which can easily reproduce in a small VMfor testing.
root@Deb11Docker01:~# docker ps
CONTAINER ID IMAGE COMMAND CREATED STATUS PORTS NAM........
The error below can be caused by a gateway that is unpingable:
docker swarm join --token SWMTKN-1-1kogg8da68gtb1j7ezaddowyy9s0an5s9tue758o20k18liskw-5h3f61hrrmv3u6agshvbtcklf 172.16.1.80:2377
Error response from daemon: manager stopped: can't initialize raft node: rpc error: code = Unknown desc = could not connect to prospective new cluster member using its advertised address: rpc error: code = DeadlineExceeded desc = context deadline exceeded........
This seems to happen in many different drivers but it happened more often in newer versions such as 530 vs 525.
Then nvidia-modeset goes to 100%
There are many reports of this appearing since driver 4.70 and I can confirm I've seen this in various machines.
https://forums.de........
Even today we see a lot of servers that have different services and ports open for rpc and this creates not only potential inward vulnerabilities but perhaps more common, the abuse of your network resources in reflective rpc queries.
To stop this problem, you should disable and remove all services relating to rpc or at least block all relevant ports for the service.
Surprisingly, there are still some providers and OS installs in Linux that install these services and leave them........
Have you ever tried mounting a partition that you exists but you get this error?
mount: /mnt: can't read superblock on /dev/sda1.
The superblock in this example was bad because the physical disk had corruption and bad blocks/sectors. However, the data was generally accessible and you can always try this trick below (with caution and no warranty).
This is specifically for filesystems that place superblocks in multiple locations, which........
[ 0.206301] [Firmware Bug]: TSC_DEADLINE disabled due to Errata; please update microcode to version: 0x3a (or later)
[ 0.430409] MDS: Vulnerable: Clear CPU buffers attempted, no microcode
[ 0.430411] MMIO Stale Data: Vulnerable: Clear CPU buffers attempted, no microcode
[ 2.980359] microcode: sig=0x306f2, pf=0x1, revision=0x36
[ 2.981621] microcode: Microcode Update Driv........
A lot of companies are unsure which solution to choose and many may not be aware of Docker Swarm as an alternative to Kubernetes. One thing that many Sysadmins find is that Docker Swarm is simply easier, quicker to setup and maintain by far than Kubernetes.........
When Is It Time to Leave Your VPS, VDS, and Dedicated Server Provider?
Choosing the right hosting solution—be it Virtu........
First we need a few extra packages:
apt update
apt install -y adduser libfontconfig1 musl sudo
wget https://dl.grafana.com/enterprise/release/grafana-enterprise_10.3.1_amd64.deb
Install / Enable Grafana
dpkg -i grafana-enterprise_10.3.1_amd64.deb
dpkg -i grafana-enterprise_10.3.1_amd64.deb
(Reading database ... 44309 files and directories currently installed.)
Preparin........
find /usr/share/zoneinfo/|sed s#"/usr/share/zoneinfo/"##g|grep "/"|grep -v posix|grep -v ^"Etc/"|grep -v ^right|grep -v ^"SystemV"
Africa/Addis_Ababa
Africa/Abidjan
Africa/Blantyre
Africa/Lusaka
Africa/Casablanca
Africa/Libreville
Africa/Asmara
Africa/Bujumbura
Africa/Dakar
Africa/Lagos
Africa/Malabo
Africa/Harare
Africa/Kigali........
If you are using a hypervisor to test Proxmox (eg. Vbox) then changing the video card/display adapter can fix it.
For example VboxSVGA causes the issue but switching to VMSVGA fixes it.
For example VboxSVGA causes the issue but switching to VMSVGA fixes it.
........
configure.ac:75: error: possibly undefined macro: AC_PROG_LIBTOOL
If this token and others are legitimate, please use m4_pattern_allow.
See the Autoconf documentation.
autoreconf: /usr/bin/autoconf failed with exit status: 1
make: *** [/software/pixman/configure] Error 1
make: *** Deleting file `/software/pixman/configure'
yum install libtool........
autoreconf: Entering directory `.'
autoreconf: configure.ac: not using Gettext
autoreconf: running: aclocal --output=aclocal.m4t
Can't exec "aclocal": No such file or directory at /usr/share/autoconf/Autom4te/FileUtils.pm line 326.
autoreconf: failed to run aclocal: No such file or directory
make: *** [/software/pixman/configure] Error 1
Just install automake:
yum install automake........
Step 1.) Upgrade to Debian 11 first
The process to go to Debian 12 is not as smooth as 11, when trying to upgrade from Debian 10. In fact, it doesn't work directly, so you'll first need to follow this guide to update to Debian 11, reboot and come back here if successful.
Step 2.) Update sources.list
Update your /etc/apt/sources.list like this:
deb http://........
If you have swarm services and dockerd is creating a high load even with the containers just being idle, the easiest solution is to upgrade to a newer docker version.
For example an identical config of 3 nodes, with Redis 5 with 30 replicas produces a load of about 1.45 in Debian 10 with Docker18.09.1
If I create the same setup on Debian 11, with Docker 20.10.5+dfsg1 then the CPU usage is low.
One other difference I wondered is the kernel. In my test setup........
If you get this error, it is often because you have configured Apache with modules that weren't actually installed. Eg. you try to load the PHPmodule but didn't actually install the apache2 php module, so the server can't start. In general, this error can often be caused by issues with problematic modules and/or Apache being configured for modules that have not actually be installed (eg. libapache2-mod-php) is missing.
The above results in this less than obv........
This should work for most console ports of other manufacturers too. It is a quick and simple method for emegencies or deploying a few appliances/devices in a non-standard environment or small environment.
However, if this is a route thing, or the equipment is not physically close to you, it would be best to use some sort of "Terminal" server which is an IP connected switch with several serial ports built-in for this purpose. Normally they accessible by web/........
You'll notice that /etc/resolv.conf contains dire warners on most Linux Desktops.
# This file is managed by man:systemd-resolved(8). Do not edit.
#
# This is a dynamic resolv.conf file for connecting local clients to the
# internal DNS stub resolver of systemd-resolved. This file lists all
# configured search domains.
#
# Run "resolvectl status" to see details about the uplink DNS servers
# currently in use........
How to check what kernel version you have/currently running?
uname -rm
5.4.0-91-generic x86_64
The above shows us that we are running 5.4.0-91-generic on the x86_64 architecture.
The safest way is to stick with the same flavor eg if you're on generic, and say on kernel 5.4.0 then it makes sense to follow what is below. However, if you are migrating or dual booting between newer hardware (eg. you got a........
We could always disable swap but this would normally be a bad idea unless you have an incredible amount of RAM and a workload that will never exceed it. However, for live/containerized and high performance environments it could be desirable.
Another middle ground may be to set swappiness to a lower number.
You may also want to clear your kernel's cache, which could be eating up RAM unnecessarily by c........
request_module: runaway loop modprobe binfmt-464c Kernel panic - not syncing: No init found Pid: 1, comm: swapper/0 Not tainted
This is usually caused by a mismatch in architecture and happens frequently in development environments.
Here is a example of what caused this issue:
Your binaries are based on one architecture
Your kernel was compiled with another architecture.
Why does this happe........
Getting this error "bash: apt-add-repository: command not found"?
You need to install the software-properties-common to solve the error:
sudo apt-get install software-properties-common........
This is a weird issue in Mint Ubuntu gnome that I've only seen on one system. It may happen in your terminal or your browser but one program will just refuse to allow input from the keyboard. I am not sure if it's some weird fluke on a strange keyboard by perhaps accidentally hitting a weird key combination.
In some windows the keyboard gets weird and only / and Esc seem to work.
/ brings up quick find and sometimes Esc will close it........
If you are installing ta-lib for Python and get this error then you can normally solve it by manually getting the ta-lib source files and compiling.
tar -zxvf ta-lib-0.4.0-src.tar.gz
cd ta-lib;./configure;make;make install
Collecting ta-lib
Downloading https://files.pythonhosted.org/packages/39/6f/6acaee2eac6afb2cc6a2adcb294080577f9983fbd2726395b9047c4e13ec/TA-Lib-0.4.26.tar.gz (272kB)
&nbs........
This has been a tried and true method for Windows because it is finicky with hardware changes without a reinstall (eg BSOD on boot is what happens 9/10 times unless you move to the same hardwar). Surprisingly, if you use a QEMU VM and do a standard install, it has worked in every system I've thrown the drive in afterwards.
So the play is this, use a USB SSD, physical SATA drive plugged internally or for convenience, you could use a SATA to USB adapter on another computer to perf........
1 - Install Vagrant
apt install vagrant
Make sure you have a supported Virtualization tool like Virtualbox or VMWare, Hyper-V etc.. It automatically detects and uses what you have. Virtualbox has a lot of support here with tons of images.
2 - Init Vagrant
We'll init to have a Debian 10 box by default to show how quick and easy it is.
vagrant init generic/debian10........
Virtualbox is a very powerful tool, but for some use cases it is less than optimal.
Say you are in a work, lab or other environment where you are not alone on the physical network and there could be overlap of IPs, but you need all of your VMs to be contactable from your host, VMs need to communicate with each other, and VMs need internet.
NAT Network will give you VM to VM communication and internet, however, it is buggy and unstable. It also doesn't allow host to VM co........
Remember that control connections are established on port 1723 and then actual data is transferred over GRE protocol 47.
If you have a NAT setup this will work without special forwarding or accepting of GRE packets (normally if you are not blocking outgoing connections and accepting established and related connections).
The below two commands will get things going so PPTP and GRE work
We first load the ip_nat_pptp module which allows PPTP to work with........
Have you checked your router/firewall logs and disconcertingly see connections to an unknown IP207.246.119.209:3478 from your Grandstream VOIPphones?
You're not alone and the Grandstream forums have discussed this issue.
However, even their own staff d........
If you find your NAT Network is not working properly, the first thing you may want to do is list the networks, check their status and make sure the Network is actually started and configured as you expect (eg. is DHCP on and enabled?).
This is a long known, unresolved bug that seems to affect Version 6 randomly and disportionately on especially Mint 20/Ubuntu 18.
https://www.virtualbox.org/ticket/1474........
Router#show license
Index 1 Feature: ipbasek9
Period left: Life time
License Type: Permanent
License State: Active, In Use
License Count: Non-Counted
Lic........
1.) Make sure your conf register is 0x2102
Do show version and at the very end of the output you will see the Configuration register.
show version
Configuration register is 0x2102
If the config register is not 0x2102 then enter this command:
r1#configure terminal
r1(config)#config-register 0x2102
r1(config)#end
2.) Let's Erase the NVRAM/flash........
It is a bit different and annoying here for these types of routers/models as you need to physically remove the CF (Compact Flash) and only then, will it enter ROMMON mode (Ctrl + Pause remotely over the console will not do it for us). This means you cannot do this remotely, or at least not without the help of a remote/physical helper.
Step 1.) Power off, router and remove CF Disk Slot#2
Go to the router and remove the slot#2 cover uses your hand or it may help to use a........
How To Fix This Cisco Switch/Router Error %Error opening tftp
%Error opening tftp://10.0.2.2/network-confg (Permission denied)
%Error opening tftp://10.0.2.2/cisconet.cfg (Permission denied)
%Error opening tftp://10.0.2.2/router-confg (Permission denied)
%Error opening tftp://10.0.2.2/ciscortr.cfg (Permission denied)
%Error opening tftp://10.0.2.2/network-confg (Perm........
Adding a default route is very simple with this command
Just replace 192.168.1.1 with the IPof your GW.
ip route add default via 192.168.1.1
How can you delete this default route if you messed it up?
It's just the opposite with "delete" instead of add
ip route del default via 192.168.1.1
This is the equivalent of the "route command's" route add default gw 192.168.1.1........
If you are getting this error from systemctl "Loaded: masked (Reason: Unit hostapd.service is masked.)" we need to unmask the service.
Solution
systemctl unmask hostapd
Removed /etc/systemd/system/hostapd.service.
It's fixed
root@routerOS:/var/log# systemctl start hostapd
root@routerOS:/var/log# systemctl status hostapd
● hostapd.service - Access point and authentication server for Wi-Fi and Ethern........
It may appear to be an Xorg or lightdm/gdm/mdm error but in reality for many users with this issue, it's a driver conflict and issue. I had a system that had two GPUs, an Intel and Nvidia GPU.
The only thing that got it working was to remove the nouveau driver and blacklist it so it never came back, then the Intel GPU works fine without these issues.
Solution
sudo rmmod nouveau
add nouveau/other driver to blacklist
edit th........
A quick fix is to run this command:
sudo brctl setageing br0 0
This causes the aging of the MAC address to time out immediately or in 0 seconds, which delete the entry frmo the FDB (Forwarding Database) and causes the error to go away. The default time is 300 seconds or 5 minutes.
You can also add it under your br0 definition like this in /etc/network/interfaces to make it permanent and automatic:
auto br........
Is your /var/log/journal overweight and bloated? For example a decent install of Debian 11 with most applications and services ends up being about 4.9G with the journal taking a few gigs.
du -hs /var/log/journal/
1.3G /var/log/journal/
By default in a lot of distributions there is no maximum size so it will keep growing. This is especially problematic for embedded distributions and devices, but is also a huge waste of sp........
The easiest way for the 8821AU Realtek Wifi chipset / TP-Link T2U Plus:
Bus 002 Device 003: ID 2357:0120 TP-Link Archer T2U PLUS [RTL8821AU]
First install your kernel headers/source/other required tools:
sudo apt install linux-headers-`uname -r` make gcc bc
Clone this github repo with the driver:
git clone https://github.com/morrownr/8821au-20210708
Run the compile/ins........
Sometimes manual intervention on various Linux system's, including Debian, is required to fix things after waking up from sleep.
One persistent issue is the sound system / pulseaudio needing to be reset and not working until you do that after waking up. It's not clear if it's an OS issue itself or the sound driver, but this will fix things.
Where do we put scripts or commands that need to be used upon wakeup automatically?
/lib/systemd/syst........
You just add on "non-free" at the end of each repo, like the example below:
If you wanted contributed packages then you could also add "non-free contrib" to each repo line.
Don't forget to do an "apt update" to see the new packages, this is especially handy for getting more drivers for devices with the firmware-linux-nonfr........
ID3 2.4 can cause various MP3 players, especially on vehicles or even computers, not to play or at least not to display the ID3 tags.
In many cases though, since ID3 2.4 is much different than version 2.3, it will cause some players, especially in cars like Lexus not to play. Even on the computer, you may notice if you check the properties of the MP3 that it won't open or show any details (eg. frequency, bitrate and ID3 tags).
One symptom of this in a vehicle (eg. Leuxs,........
Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows.
There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........
This can be used on almost anything, since Gluster is a userspace tool, based on FUSE. This means that all Gluster appears as to any application is just a directory.
Applications don't need specific support for Gluster, so long as you can tell the application to use a certain directory for storage.
One application can be for redundant and scaled storage, including for within Docker and Kubernetes, LXC, Proxmox, OpenStack, etc or just your image/web/video files or even da........
Let's say you have a VM file that uses 200G of dynamic space, but really only has 40G in usage. If you add fles and delete, at some point the file will be larger than the current space you are using.
Take this image which shows is using 71G of space on the host:
The actual space being used inside the image is about 43G as we can see:........
This may be necessary if you have a VM or if for some reason you just want to be more efficient with your space and have the flexibility of changing your swap space at will.
What we mean is the ability to use a "swap file" or similar to the Windows "pagefile" that normally resides on the root or c: partition of Windows.
Here's all you have to do and then you to can have a single partiton with everything, including the swap file on the root partition if you........
(firefox:9562): LIBDBUSMENU-GLIB-WARNING **: Unable to get session bus: Failed to execute child process "dbus-launch" (No such file or directory)
ExceptionHandler::GenerateDump cloned child 9743
ExceptionHandler::WaitForContinueSignal waiting for continue signal...
ExceptionHandler::SendContinueSignalToChild sent continue signal to child
[Parent 9562, Gecko_IOThread] WARNING: pipe error (40): Connection reset by peer: file /build/firefox-EymEXX/fire........
The Best Docker Tutorial for Beginners
We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........
Why choose OpenVPN instead of a firewall appliance?
OpenVPN can be a reliable and easy replacement for traditional hardware or just be an additional tool that your company uses so that the firewall can focus on its job rather than acting as a VPNappliance at the same time.
When comparing OpenVPN with traditional firewal........
In our 2024 VPS Server/Cloud Buyer's Guide, we place the location of your VPS/hosting/server as one of the priorities that is often overlooked.
2024 Update - Datacent........
How To Install Wazuh Server / Quickest Installation
Wazuh (forked from the well known OSSEC project) is a full SIEM (Security Information Event Management) that works extremely well with the platforms it natively supports as an "Agent", which allows you to do scans of everything such as all processes running, CVE vulnerability check, incident reporting etc...
Prerequisites:
A lot of issues with Wazuh seem to be caused by i........
1. Let's work from an environment where we can install Ansible on.
If you are using an older version of Linux based on Mint 18 or Ubuntu 16, you may want to get the PPA and get the latest version of Ansible that way:
sudo apt install gpg
sudo add-apt-repository ppa:ansible/ansible
sudo apt update........
How To Install Ceph
If you stopped an install of Ceph midway you will need to manually restart it with "pveceph install"
Remember that your VM needs to have working internet (gateway) and DNS in order to connect to the apt repo to download all of the packages that Ceph requires.
Remember to repeat these steps for each node that you want Ceph on.
........
There are many reasons why Proxmox services may not start, but one common one, is if you have changed your /etc/hostname or /etc/hosts and don't have a valid FQDN (eg. proxmox01 instead proxmox01.com).
Failed to start The Proxmox VE cluster filesystem.
Failed to start Proxmox VE firewall.
Failed to start PVE Status Daemon.
Failed to start Proxmox VE scheduler.
Failed to start PVE Cluster HA Resource Manager Daemon.
Failed to star........
NAT Network, the VMs can communicate but your host cannot access them by default.
NAT VMs have internet but cannot communicate with each other.
Bridged is simple and allows full LAN access as if you had a physical machine plugged in but is often bad for testing, work or corporate environments and is not very portable when it comes to moving your VMs to other locations and networks.
Here is how you can use NAT Ne........
From the terminal do this:
cat /proc/cpuinfo|grep -E "svm|vmx"
You should get output like this(svm = AMD-v and vmx=Intel-VTx):
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc cpuid aperfmperf pni pclmulqd........
Kubernetes Easy Beginners Architecture Guide
Kubernetes is known as container orchestration and we should start at explaining the container part of it.
A Container is what runs the actual application and based on an Image, and are more comparable to something like an LXC Container, Virtuozzo/OpenVZ using the Linux Kernel Namespaces feature. Containers run these images as independent, isolated operating environments under the OS's exist........
This assumes that you've already installed the relevant HWIC cards eg. Cisco Asynchronous Serial NIM
These are essentially cards that you install into your router, once installed you connect an Async cable to one of the ports on the card which normally gives you 8 console cables and are normally labelled 1 through 8.
You connect all of the cables to the devices you need (even non-Cisco devices) whether switches, routers or firewalls, they will usually work.
The real m........
This seems to be an ongoing issue that is still reproducable in the latest Ubuntu Vbox 6.x.
The default NAT Network range is usually 10.0.2.0/24. If you change this range it does not seem to work properly.
Say we change the range to 10.50.1.0/24
If you get a new lease you will find that you get an IP from the old range but the default gateway is from the new range.
........
Just a quick note and warning is that if you are testing to see if EFIPXE booting works on a VM, MAKE SURE it actually works. For example Iinitially tested using my Distro's QEMU 2.5+dfsg-5ubuntu10.46 and ovmf BIOS firmware (OVMF supports EFI). However, I found on old versions of QEMU (like 2.5), EFIbooting with GRUB NEVER works so it may appear that you have made a mistake when everything is fine when you boot a physi........
Enable "cli" mode equivalent in JunOS
cli
Configure Mode
configure
So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure".
How Do You Apply Changes You've Made?
You can make all kinds of changes to the switch, but remember they are not........
Many people may not be aware that you can turn commodity hardware into a Mikrotik OS and there are various options which is "CHR" (Cloud Hosted Router) which is a VMimage meant for Virtualization only (seriously, I've tried to dd the image to a physical server and it just crashed as it does not contain any drivers for physical).
One note as well if you are trying to do a baremetal install you may get an error "Error Loading Operating System" or........
I have a Canon MF642c and the scanner wouldn't work. I tried to use saned but it didn't work with the BJNPlike it did for some other Canon models.
Introducing sane-airscan with packages for the most common distributions: https://software.opensuse.org/download.html?project=home%3Apzz&package=sane-airscan
http........
It took a lot of fiddling to make a Huion Kamvas 13 Pro work in Linux but it simple once you know what to do. Don't bother searching as it is unlkely there is a guide out there that will actually make your tablet work.
It mainly comes down to the fact that the hid_uclogic kernel module is buggy or doesn't support MANYof these wacom based/Huion tablets properly.
What was happening with me is that Ihad the Kamvas 13 Huion setup as a secondary screen/monitor.&nb........
A very common use case is that you don't want to waste time using a video editor that requires you to open it up and manually import the video clip and audio clip, then manually delete the old audio track and import the video and new audio. That's too much work and time since we don't want to go through the hassle.
ffmpeg is our solution, all we have to do is specify 3 variables and we're done!
-i Windows2019-Server-Noaudio.mp4 is our in........
In QEMU 4 or higher you can no longer use the normal "-soundhw ac97" flag and it is much more complicated but here is a simple copy and paste on Linux that will just work:
-audiodev you have to use -audiodev to specify the driver and id
driver=pa
id=someid
-device you have to specify the same audiodev id you used in -audiodev and driver
-audiodev driver=pa,id=pa1 -devic........
It really seems limited in that it can mainly give you the things you would see on the physical unit such as load etc..
wget https://downloads.sourceforge.net/project/apcupsd/apcupsd%20-%20Stable/3.14.14/apcupsd-3.14.14.tar.gz?r=https%3A%2F%2Fsourceforge.net%2Fprojects%2Fapcupsd%2Ffiles%2Flatest%2Fdownload&ts=1598115866
tar -zxvf apcupsd-3.14.14.tar.gz
cd apcupsd-3.14.14
[root@somebox apcupsd-3.14.14]#
./conf........
If you've come here, don't be embarraassed, working in IT, this is the MOST common computer problem that almost everyone will encounter. The reason why I'm doing this post is because I've seen an increase from colleagues and admins having this problem and many times it's not even your fault. A common scenario is that someone acquires a new or used computer which they weren't given the password for. Fortunately Ihave a detailed list of all the options whether free or pa........
Is a mdadm check on your trusty software RAID array happening at the worst time and slowing down your server or NAS?
cat /proc/mdstat
Personalities : [raid1] [raid10]
md127 : active raid10 sdb4[0] sda4[1]
897500672 blocks super 1.2 2 near-copies [2/2] [UU]
[==========>..........] check = 50.4% (452485504/897500672) finish=15500.3min speed=478K/sec
........
This is very frustrating but the fix is usually easy once you read this blog. It's very frustrating when you find that your Linux / Ubuntu laptop's wifi will NEVER work unless it is plugged into the power. The wifi menu may say "Wifi disabled by hardware switch". You may find that your laptop has no switch or has a function wifi button on the keyboard but this does not work or have any effect.
The cause is usual a "wmi" kernel module and simply doing an........
yum -y install gcc make gperf genisoimage flex bison ncurses ncurses-devel pcre-devel augeas-devel augeas readline-devel
checking for cpio... cpio
checking for gperf... no
configure: error: gperf must be installed
configure: error: Package requirements (augeas >= 1.2.0) were not met:
Requested 'augeas >= 1.2.0' but version of augeas is 1.0.0
yum remove augeas augeas-libs augeas-devel
wget http://downl........
apt install software-properties-common
add-apt-repository ppa:deadsnakes/ppa
apt update
apt install python3-pip
apt install python3.7 curl gnupg python3.7-dev git
ln -s /usr/bin/python3.7 /usr/bin/python3
pip3 install numpy keras_preprocessing
curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add -
echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........
yum -y install wget unzip
wget https://download.nextcloud.com/server/releases/nextcloud-18.0.2.zip
unzip nextcloud-18.0.2.zip
yum -y install php php-mysqlnd php-json php-zip php-dom php-xml php-libxml php-mbstring php-gd mysql mysql-server
Last metadata expiration check: 0:58:02 ago on Fri 13 Mar 2020 02:12:49 PM EDT.
Dependencies resolved.
===================================================================........
unable to connect to camera. Camera has been disabled becaue of security policies or is being used by other apps
They say to do a factory reset but in some cases it doesn't work and the camera mysteriously just won't work so it appears to be a hardware error if that happens.........
This is sure simple if you follow the guide but it took a lot of hacking around to make this work on Debian/Ubuntu!
Now before you ask why bother running wine and python, the reason is because Python executables are NOT cross-platform. If you run pyinstaller in Linux, that binary will only run on Linux and the same if you do it in Windows. So it is preferable if you have a single environment that you can create Linux and Windows binaries from rather than running 2 separate........
Occasionally my whole screen locks up and I cannot even swith to the console and I find this in my syslog:
*-display
description: VGA compatible controller
product: Mullins [Radeon R3 Graphics]
vendor: Advanced Micro Devices, Inc. [AMD/ATI]
 ........
This is only really necessary in the case you don't want DHCP. If you are dealing with an encrypted LUKS server on the internet, you will often want to have a static IP so you know which IP to connect to (or if you have a semi-static IP assigned by DHCP).
SET IP Address by /etc/initramfs-tools/initramfs.conf
IP Address=192.168.1.27
Gateway=192.168.1.1
Subnet Mask: 255.255.255.0
Hostname=myhome.com
IP=192.1........
The reason for doing this is that the installer doesn't seem to work properly for LUKS and the server installer doesn't even support LUKS anymore. When you use the GUI install on Desktop for LUKS it won't boot and will just hang after you enter your password. So the only reliable way is to do it ourselves.
1.) Make a default minimal install of Ubuntu
2.) Have a secondary disk on the server or VM.
3.)........
Create your netplan file
vi /etc/netplan/01-netcfg.yaml
network:
version: 2
renderer: networkd
ethernets:
ens3:
dhcp4: no
........
The cool thing here is that we only need 1 drive to make a RAID 10 or RAID 1 array, we just tell the Linux mdadm utility that the other drive is "missing" and we can then add our original drive to the array after booting into our new RAID array.
Step#1 Install tools we need
yum -y install mdadm rsync
Step #2 Create your partitions on the drive that will be our RAID array
Here I assume it is /dev........
This is the reason that I don't like the new ADATA USB drives such as the UV128/64GB or 128GB drives and other ones that look to be the same style (the green sliding USB connector).
They just don't work well from new and never work properly at any point.
[ 788.242463] usb 1-1.2: new high-speed USB device number 16 using ehci-pci
[ 788.339816] usb 1-1.2: New USB device found, idVendor=125f, idProduct=db8a
[ 7........
I find that the default settings for the radeon driver that is applied to most AMD cards is horrible. For example by default TearFree is not enabled and it causes videos to have some kind of square artifacts.
Here are the settings I have found most suitable for AMD cards:
You need to create file in the following path and restart Xorg or your computer to apply it:
*Beware that making a mistake here will possibly make your computer........
This is a gotcha but be aware sometimes iptables may be active and loaded by default.
Also make sure you don't just disable firewalld but also stop it otherwise it will still block stuff:
systemctl stop firewalld
If the above is not the issue then it is possible iptables is running and blocking stuff too, so you'll need to stop iptables.
So in addition to opening firewalld or disabling it, you would need to disable iptables........
mysql reset root password.
Oops I can't remember my MySQL root password!
[root@centos7test etc]# mysql -u root -p
Enter password:
ERROR 1045 (28000): Access denied for user 'root'@'localhost' (using password: YES)
First we need to stop mariadb:
systemctl stop mariadb
Now we need to restart it with skip-grant-tables whic........
sudo pip3 install python-docx
[sudo] password for :
Downloading/unpacking python-docx
Downloading python-docx-0.8.10.tar.gz (5.5MB): 5.5MB downloaded
Running setup.py (path:/tmp/pip_build_root/python-docx/setup.py) egg_info for package python-docx
no previously-included directories found matching 'docs/.build'
warning: no previously-included files matching '.DS_Store' foun........
yum install iptables-services
systemctl enable iptables
service iptables save
iptables: Saving firewall rules to /etc/sysconfig/iptables:[ OK ]........
Having a network bridge allows you to bridge traffic under multiple devices so they can talk natively without using any special routing, iptables/firewall or other trickery.
To create your bridge you need the bridge-utils package for brctl and if you want to do things like bridge VMs that run on a tap device you will need the uml-utilities which provides "tunctl".
1.) Install the utilities to make our bridge
sudo apt-get i........
CPU:Intel(R) Core(TM) i3-2120 CPU @ 3.30GHz
MOBO: Manufacturer: ASUSTeK COMPUTER INC.
Product Name: P8H61-M LX3 PLUS R2.0
qemu-kvm-0.12.1.2-2.506.el6_10.1.x86_64
This is weird but the only OS I've found this machine doesn't work with is Windows 2019 Server. Ihave no idea, when 2008, 2012 work f........
SSH helps keep us secure in many ways, one of those is the host-key fingerprint which is unique. If you have been connecting to an SSH server that you've made no changes to and suddenly ssh warns that the key doesn't match then you have a problem.
But how about connecting to an existing server for the first time on a new machine or client?
A lot of new clients calculate it using an SHA256 hash but it is not as easy on your host machine to produce the sam........
This would be crucial especially if the phone is hardened, not being able to reset or change settings could prevent a phone registering in a new environment or even when migrating from office to office. This applies even if you are trying to migrate the phone to another platform such as Asterisk/FreePBX etc...
This guide applies to nearly all of the Cisco IP phones that you would use in CME or CUCM from several years ago including models: 9900, 9971, 8800, 8900, 8845, 8851, 8841........
I have seen this in a few rare cases after a reboot, where all folders and files will have the Read Only Attribute. If you uncheck it, it will just come back. It is more of a filesystem issue in Windows than a configuration issue and it looks like when Windows detects a badly corrupted filesystem that it will make things read-only, sort of like Linux would.
If you are Administrator or the owner of the folder and this is happening it is probably due to the reasoning mention........
The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs.
qemu-kvm command:
/usr/libexec/qemu-kvm -version
QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard
........
Oops did you get this error trying to install an oldschool driver and think it is hopeless in a new version of Windows?
First of all it is almost never a program compatibility issue:
........
chroot which stands for change root allows you to virtually operate in another operating system even though you haven't booted it. It is commonly used to deploy new distros, applications and to fix a broken Linux/Unix install or prep a new system image without having to physically boot the drive or disk.
So in this example let's say we have a drive that has a Linux OS installed on /dev/sdb1 and we have mounted this partition on /mnt/sdb1
The key point is to edit the &quo........
This is a common issue that I haven't seen many answers for on the internet. When you are using Linux as your host machine and you are connecting to another Linux machine over VNC you CANNOT use Ctrl+Alt+F1 to change virtual consoles as it sends the keys to your actual local machine.
In many versions of Linux you can cycle through virtual terminals including over VNC using this:
Alt + Left Arrow or Alt + Right Arrow
This........
Install Issues:
How to Make CUCM iso /modify to work on non-VMWare machines like QEMU/Xen/OpenStack
If you get kernel panic errors in VBOX usually disabling Nested Paging will fix the issue (thanks to Mark).
ks_pre.sh error is caused by having the wrong VDX pattern (change it do sd per guide link above) and/or the wrong VMSpecs (Cisco req........
So say you are behind a typical NAT/LAN setup whether at home, work or while travelling. What if you have a computer or server that you need to connect to from the outside?
Yes you could use a VPN but a quick and dirty, temporary and secure way is to use SSH's Reverse Tunneling Proxy feature.
Requirements
On the remote ssh server host you need the GatewayPorts option enabled in sshd_config (be........
In most of the Cisco router IOS I find the ports like ge0/0 ge0/1 and ge0/2 or whatever your ports are down. They will not even give you a link light. So one of the first tasks should be getting the port you are working with up.
In my case the first goal is often connectivity with the LAN and WAN.
LAN = your local area network (eg. in the office/home )
WAN= your ISP/public internet (eg. fiber/cable/dsl/ethernet).........
Switch#show ip dhcp snooping
Switch DHCP snooping is disabled
DHCP snooping is configured on following VLANs:
1
Insertion of option 82 is enabled
circuit-id format: vlan-mod-port
remote-id format: MAC
Option 82 on untrusted port is not allowed
Verification of hwaddr field is enabled
Interface&nb........
This works on the 2000 and 3000 series generally.
*The easy way is to just hold the mode button for 10+ seconds.
The full/proper way is below:
1.) Either power on the unit and hold the "mode" button or hold the "mode" button until you see the below:
00:04:08: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram
00:04:08: %EXPRESS_SETUP-6-CONFIG_IS_RESET: The configur........
The key thing is that you must use a "machine"id of "pc-1.3" or it will say your hardware is not supported.
Additionally you MUST use a virtio disk or you will get a ks_pre.sh error as soon as the install starts (a look at logs will show it can't find a disk). This is funny because even though the OS finds the disk and an fdisk -l shows it, it looks like the script looks for a /dev/vda device (virtio) and nothing else, so if you didn't use Virtio as you........
Idid a systemctl restart networking and it broke Proxmox VM connectivity!
#proxmox is the problem after restarting the network the tap devices go to disabled state
[2230884.919905] vmbr0: port 7(tap118i0) entered disabled state
[2230884.948864] vmbr0: port 8(tap122i0) entered disabled state
[2230884.972748] vmbr0: port 6(tap119i0) entered disabled state
[2230885.004745] vmbr0: port 5(tap117i0) entered disabled state
[2230885.03673........
debug1: Local connections to LOCALHOST:18006 forwarded to remote address 192.168.1.93:8006
debug1: Local forwarding listening on 127.0.0.1 port 18006.
debug1: channel 0: new [port listener]
debug1: Local forwarding listening on ::1 port 18006.
bind: Cannot assign requested address
What we are seeing is that we can't listen on an IPV6 address of ::1. We need to tell SSH to stop using IPV6 so we'll edit ssh_config to take care of this issue........
Jan 30 17:16:10 localhost sshd[25385]: error: Failed to allocate internet-domain X11 display socket.
The solution for me on the server side was the following in sshd_config:
AddressFamily inet
*Remember to restart sshd and also reconnect from the client side.
Ihad all the normal X11 settings on the server but it just stopped........
The defaults in Windows 2016 server leave clients crippled so they can't even download basic files or software. But Group Policy Management Editor comes to our rescue!
Use cmd or Powershell and run:
gpme.msc
Choose your domain/computer and then navigate like below and create a new menu entry for IE11 or whatever your version is. Don't be worried if the highest version is IE10 it means that it applies to IE10 AND above.........
Whether you are at work, at the coffee shop or on the public internet here are some basic but effective rules for iptables that lock things down (eg. no one can SMB or SSH to you or really anything):
# Generated by iptables-save v1.4.21 on Fri Dec 14 14:00:08 2018
*nat
:PREROUTING ACCEPT [160:19844]
:INPUT ACCEPT [4:357]
:OUTPUT ACCEPT [2955:182236]
:POSTROUTING ACCEPT [2955:182236]
COMMIT
# Completed on Fri Dec 14........
By default VMWare Workstation often doesn't work as we would like.
If you create a VM with a default NAT IP it won't work you will find the NIC is disconnected (even though on the VMWare side it says connected including at Power On).
How To Solve It
1.) Create New VMNet for NAT
Click "Edit" -> "Virtual Network Editor"
Click "Add Network"
Select Network To Add "VMNet1" (........
Below are the common errors you'll get with named AKA bind if your time is incorrect.
The simplest solution is to install and run ntpd to correct your system's time (install ntpd if it is not installed)
systemctl start ntpd
systemctl enable ntpd
Dec 20 13:36:16 hostingbox named[2169]: error (no valid DS) resolving 'develop.waxrain.com/A/IN': 14.215.150.17#53........
A lot of people just have a -j DROP to drop all unwanted traffic or traffic not explicitly allowed but there is a better solution if you want real and proper logging:
Here is another example of more advanced iptables rules.
Take an example iptables rules file
-A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT
-A INPUT -i eth1 -p icmp -j ACCEPT........
Before getting into the output here is my typical experience with SMART, there is what I call a "bad disk" with pending and uncorrectable sectors that cannot be reallocated.
It has caused a kernel panic and system crash repeatedly as we can see from the logs.
But SMART says it has "PASSED" its self assessment. SMART is still useful to me but it is more about looking at Current_Pending_Sector.
Any time I have had anything but 0 for that attribute it........
< a href="/Products/MX72244">
< span class="c-shca-icon-item__body-name-brand">
ADATA
< / span>
&nbs........
Cisco's CUCM (Cisco Unified Communication Manager) is a system that combines voice, video, data and mobile products into a single unified management suite. At its core, the CUCMis like a "Super PBX" that controls the flow of all communications through an organization even single or multiple site deployments.
Cisco's CUCMmakes communication more effective and simple through centralized management and unification of communications resources.........
mytop is one of my favorite tools and it is fairly simple aside from a few caveats and issues that persist to this day.
To install it on Centos:
yum -y install centos
Configure ~/.mytop
vi ~/.mytop
user=root
host=localhost
db=test
#port=3306
socket=/var/lib/mysql/mysql.sock
header=1
color=1
Try runni........
When converting binary the easiest way is to write out a vertical list in a format like below and follow the formula in the table.
Example Convert 1101 1111 to decimal.
Step 1.)
Write out the binary below in vertical form (leave lots of space on the left side).
Keep this in mind that the "previous sum" starts at 0 on your first line.
Step 2.)
Formula:
2 *........
systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system.
The key commands or arguments you will use with systemctl are the following:
Unit Commands:
list-units [PATTERN...] List loaded units
&nbs........
Ihave a directory structure which the primary user needs full access on but wanted a user to access only a specific directory within the main directory (so they could write in there only and nowhere else).
Here's what Idid:
[root@compevo8001 dllnow]# ls -alh
drwxrwxr-x 2 someuser software 4.0K Oct 19 2017 ExpireYMD-2017-11-20
drwxrwxr-x 2 someuser software 4.0K Nov 19 2017 ExpireYMD-20........
wget https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe
--2018-08-16 05:11:16-- https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe
Resolving downloads.linux.hpe.com (downloads.linux.hpe.com)... 15.249.152.85
Connecting to downloads.linux.hpe.com (downloads.linux.hpe.com)|15.249.152.85|:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: 1525561 (1.5........
Error 0 occurred while receiving the document
root@vh1:/var/tmp# wget http://mirror.compevo.com/proxmox/proxmox-ve_5.2-1.iso
--2018-08-30 16:27:37-- http://mirror.compevo.com/proxmox/proxmox-ve_5.2-1.iso
Resolving mirror.compevo.com (mirror.compevo.com)... 103.25.61.44
Connecting to mirror.compevo.com (mirror.compevo.com)|103.25.61.44|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 641517568 (612M) [application/o........
After starting the install it stalls here:
admin/index.php?cache=0&agreelicense=1&confirmrelease=1&lang=en
If you manually refresh you get a Plugins check screen:
Installation
System
Moodle second step fails just blank screen:
https://domain.la/user/editadvanced.php?id=2
Solution: give up and choose something else it shouldn't be thi........
[root@localhost:~] vmkping -I vmk1 10.0.2.69
PING 10.0.2.69 (10.0.2.69): 56 data bytes
sendto() failed (Host is down)
vsphere distributed switch vmotion not working
[root@localhost:~] esxcfg-route -l
VMkernel Routes:
Network Netmask Gateway Interface&........
503 Service Unavailable (Failed to connect to endpoint: [N7Vmacore4Http20NamedPipeServiceSpecE:0x00005556ba09c070] _serverNamespace = / action = Allow _pipeName =/var/run/vmware/vpxd-webserver-pipe)
503 Service Unavailable (Failed to connect to endpoint: [N7Vmacore4Http16LocalServiceSpecE:0x00007fd26000b240] _serverNamespace = /ui action = Allow _port = 5090)
Errors like the above are usually because there is an issue with your vSphere or more commonly it i........
How to check if nested KVM is enabled by doing a cat on nested inside sys
Nested KVM is mainly important for testing for example if you wanted to install VMWare or Proxmox Nodes in a virtual environment for testing. Without nesting, the performance will be extremely slow, since the VMs within the nodes will not be using Virtualization extensions.
I've used wildcard on kvm_ because it could be kvm_intel or kvm_amd depending on whether y........
You can find many ways to specify the VLANin your network configuration but Ifind this is the simplest and quickest.
In this case we are talking about a bridged adapter "vmbr0" but it works even if you just had a normal non-bridged interface.
The key here is that in vmbr0 you'll notice there is no IP address. We just specify "manual".
Below it is a similar stanza for "vmbr0.58" in this case 58 represents the VLAN (change........
[root@localhost:~]
BootModuleConfig.sh echo host-ind nfcd........
yes it does create its own json
============================================
cat /tmp/vcsaUiInstaller/ovftool-20180809-175238948-20180809-175603497.log |grep -i json
2018-08-09T17:56:04.238-07:00 verbose OVFTool[30966] [Originator@6876 sub=Default] Manifest file entry: SHA1(VMware-vCenter-Server-Appliance-6.7.0.12000-8832884_OVF10-file1.json) = 1deb658c724767697587d5909c4051c01813e6a1
--> ........
./tronwatch: error while loading shared libraries: libasound.so.2: cannot open shared object file: No such file or directory
[root@testing linux-unpacked-1.0.7]#
Solution:
yum -y install alsa-lib-devel........
Aug 10 01:11:54 mailserver postfix/smtp[6180]: 020AE17C2BD1: to=, relay=none, delay=0.29, delays=0.28/0/0/0, dsn=5.4.4, status=bounced (Host or domain name not found. Name service error for name=gmail.con type=A: Host not found)
A user complained that their e-mails weren't being delivered but they actually made a small typo and used gmail.con so it wasn't working as expected of course........
There is no such option as "VBS" that Ican see in vSphere 6.7 Ibelieve this is actually an issue because of using old hardware in this case L5420 doesn't support Nested Virtualization I believe.
Hardware virtualization is selected and cannot be deselected due to selection of VBS
Insufficient resources to satisfy configured failover level for vSphere HA.........
sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3
sudo apt-get install libcurl4-gnutls-dev
git clone https://github.com/wolf9466/cpuminer-multi
sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev
git clone https://github.com/fireice-uk/xmr-stak-cpu.git
make install
cd bin
chmod +x xmr-stak-cpu
./xmr-stak -O xmr........
top - 13:02:52 up 603 days, 19:19, 2 users, load average: 5.01, 4.15, 3.44
Tasks: 604 total, 5 running, 599 sleeping, 0 stopped, 0 zombie
Cpu(s): 17.7%us, 36.1%sy, 0.0%ni, 42.0%id, 4.1%wa, 0.0%hi, 0.2%si, 0.0%st
Mem: 16278908k total, 4269684k used, 12009224k free, 119672k buffers
Swap: 8k total, ........
convert "file.TIF" "resize.jpg"
convert.im6: Unknown field with tag 317 (0x13d) encountered. `TIFFReadDirectory' @ warning/tiff.c/TIFFWarnings/788.
I've been getting this error in ImageMagick on some .tif files even though it seems to actually convert properly.........
This is often the result of PayPal's "item name" or another name having invalid characters or not supporting Unicode.
173.0.81.1 - - [17/Jul/2018:13:39:45 -0400] "POST //modules/gateways/callback/paypal.php HTTP/1.1" 406 - "-" "PayPal IPN ( https://www.paypal.com/ipn )"
A good clue is if you check the debug output of the IPNand find a mandatory column empty.
........
dvd+rw-mediainfo /dev/sr0
INQUIRY: [ASUS ][BW-16D1HT ][3.00]
GET [CURRENT] CONFIGURATION:
Mounted Media: 11h, DVD-R Sequential
Media ID: RITEKF1&n........
We all know Linux is known for good memory management but is it really? It seems all on its own with hardly anything running that you can come back in days or weeks and find that almost all of your RAMis used!
And many will say "no don't worry it's buffers for optimization" but it doesn't seem to help because what is in buffers is not available to use for new programs running or ones that allocate more RAM as far as Ican tell.
The reason Iknow........
I've read a few guides about this but they didn't work for me.
sudo apt-get install bridge-utils
#don't think the above is enough it won't work still even though you have by default an /etc/qemu-ifup that handles it if you have the right tools and setup
sudo qemu-system-x86_64 -net tap -net nic -enable-kvm -cpu host,vmx=on ~/VirtualBox VMs/vsphere-vcenter/vsphere-vcenter.vdi
W: /etc/qemu-ifup: no bridge for guest interface foun........
InternalServerError (com.vmware.vapi.std.errors.internal_server_error) => {
messages = [LocalizableMessage (com.vmware.vapi.std.localizable_message) => {
id = vapi.bindings.method.impl.unexpected,
defaultMessage = Provider method implementation threw unexpected exception: com.vmware.vapi.std.errors.InternalServerError,
args = [com.vmware.vapi.std.errors.InternalServerError]
}],
data =
}
I was getting the........
Intel VT-X is enabled in Virtualbox but it doesn't seem to pass through the needed vmx extension despite the following variables on the host confirming it is enabled:
cat /sys/module/kvm_intel/parameters/nested
Y
cat /sys/module/kvm_intel/parameters/ept
Y
OVF Tool: Disk progress: 99%
OVF Tool: Transfer Completed
OVF Tool: Powering on VM: Embedded-vCenter-Server-Appliance-
OVF Tool: Task p........
I had this error in an unsupported CPUon VMWare 6.7 and apparently this sometimes works especially on older VMWare versions like 6.5 5.5 etc (but in my case it did not).
To make sure it proceed when you see "Loading VMWare"
Hit "Shift+O"
Then add "ignoreHeadless=TRUE"
See an example below:........
#mount the VCSA DVD
mount /dev/sr0 /mnt/cd
#alternatively you could mount the iso directly
mount -o loop vcsa.iso /your/mount/path
#for this purpose we are using the CLI installer on Linux
cd /mnt/cd/vcsa-cli-installer/lin64
#no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file
./vcsa-deploy
Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........
The reason for this article is because a lot of us don't physically see our hard drives they are often remote in a datacenter etc and the actual serial number we see in SMART is not enough to check for some manufacturers.
A good example is our first one the Toshiba
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA DT01ACA200
Serial Number: 33FMDW4AS........
Sometimes if you have a very basic configuration OpenVPN on the client side for some reason sends all traffic to the OpenVPN server IP through the tun0 which is of course impossible and creates a block or routing loop.
This is because you need to use your normal ISP/LANgateway to hit the OpenVPN server if it is remote/offsite as is usually the case. So if you are connected to the OpenVPN through say a tun0 device and your routing is set to connect to the OpenVPN&nbs........
This is not the normal "black screen"issue and I was shocked to eventually find out why. The normal advice of reconfiguring Xorg didn't work. Even booting into "Recovery Mode" did not help.
Here is the short end of the stick that fixed it:
sudo apt-get install mdm mate-desktop-environment
Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled. This must be whe........
Here is the only solution Ifound that works in Firefox:
*Note you could basically just copy all of the commands in bold (the rest just shows the output)
Install sqlite3
sqlite3 places.sqlite
sqlite> .clone places.sqlite-fixed
moz_places... done
moz_historyvisits... done
moz_inputhistory..........
ValueError: new value non-existent xfs filesystem is not valid as a default fs type
Pane is dead
From what Iread this is misleading and has to do with the fact that the initrd and kernel are mismatched.
This is a hard situation because for some older hardware Iam using the Centos Plus kernel which has modules that Irequire for an older server/NIC. This seems to have cropped up in the past few months and there is no simple fix........
It looks like this has something to do with APIC but I am not sure. I have similar CPUs with a different MB and BIOS that work fine on the same type of kernel. A lot of time the issue is because of the C-step setting in the BIOS.
The same thing happened on the 2.6 kernel with Centos 6 but this is a homebrew 4.4 kernel soI am not sure why it is happening when even Centos 7 (3.2) kernel works OK.
Solution - It comes down to the BIOS set........
It is well known hackers, the NSA, CIA and other groups have created malware to secretly turn on your webcam and microphone on your phone, tv etc.. But fortunately on our computers and laptops we have some options.
Most webcams use the "uvcvideo" kernel module / driver. You can disable this in two ways on boot. I recommend both just as a failsafe.
Disable it on rc.local once your system boots automatically
Add the followi........
sudo chmod 000 /etc/cron.daily/apt-compat
This is the easiest way to disable the cron without anything more invasive like deleting the file.
After that you won't have anymore apt-get's starting.
This can be critical for systems without much extra RAMthat is not in use. I've seen systems that have swapped and crashed over apt-get.........
I've never seen this before in all of my years. Ihave some very old CDs and DVDs 12-15 years old that seem not to work in this BD-R/DVD-R/CD-R Asus drive.
The discs are fine actually and ironically they even work fine on a normal LG USB based BD-R drive!
Here are the errors in Linux:
[2914936.884924] attempt to access beyond end of device
[2914936.884927] loop1: rw=0, want=730424, limit=688384
[2914954.556873] attempt to........
I don't recall having this issue in the distant past but nowadays at least Debian seems to be very picky about this.
I used dd to copy one hard drive to another and tried booting it. Everything seemed fine with grub working but each time it would drop to the busybox shell. There is no particular error so this is misleading.
Normally the first things you would check are to make sure your fstab is correct (that the UUID is correct)and that you've updated grub.&........
MySQL will silently truncate a larger INT than capable.
Check MySQL's own documentation here:
As we can see the maximum size of INT (which is the most commonly used) is 2147483647
A lot of coders make this mistake by using very large values such as 9999999999 but it would actually truncate to 2147483647 which is the maximum size of an INT. This is dangerous beca........
By default Samba SMB/NMB listen on ANY and ALLIPs on your system by binding to 0.0.0.0. Obviously this is a huge security risk if you have a public facing server with both internal and external access. Usually when a system administrator sets up a samba server their intention is just to share with a LAN.
To do this you need to the following options under the [global] section in smb.conf
bind interfaces only = yes
interfaces = 192........
Check for crap in /var/lib/mysql like this
ls -al /var/lib/mysql/
total 20888
drwxr-xr-x 24 mysql mysql 4096 Oct 3 18:30 .
drwxr-xr-x 20 root root 4096 Oct 3 04:23 ..
-rw-rw-rw- 1 mysql mysql 11776 Oct 3 17:10 c:exp.exe
-rw-rw-rw- 1 mysql mysql 48128 Oct 3 17:10 c:exp1.exe........
This is not just a Linux issue but a general issue most software or hardware players cannot play the resulting exported/backed up format of .h264 from DVR security camera footage for some silly reason.
There is a simple solution in Linux using ffmpeg fortunately.
Convert the .h264 file into mp4
ffmpeg -i yourfile.h264 -codec copy video.mp4
play dvr .h264 file........
It's really simple and just a matter of the following line within the subnet declaration.
deny unknown-clients;
See example below:
subnet 10.25.20.0 netmask 255.255.255.0 {
range 10.25.20.11 10.25.20.254;
deny unknown-clients;
option routers 10.25.20.10;
option domain-name-servers 208.67.222.222;
 ........
In Thunderbird in a very large folder suddenly all of my e-mail list became blank/white even though you could click on the invisible/white/blank lines and it would show the e-mails. Itried to close and reopen but only going to Folder -> Properties and clicking Repair Folder fixed it (basically it had to redownload/rebuild the entire index and all e-mails).........
add this style="background-size: contain;max-width: 100%; height: auto;" to your img code.
Example: ........
So you've got a responsive site with tables but it breaks them so anything not viewable on the screen is now cut off.
Here is a simple solution that will allow users to scroll horizontally so they can see the whole table:
&........
I'm having trouble making it work on very shaky video the result seems kind of warped/blurry/fish eye like and not as good as some other examples I've seen:
ffmpeg -i MVI_1285.MOV -vf vidstabdetect=shakiness=10:accuracy=15 -f null MVI_1285.trf
ffmpeg -i MVI_1285.MOV -vf vidstabtransform=smoothing=30:input="transforms.trf" MVI_1285.MOV.mp4
I've played around with the shakiness, accuracy etc.. but not the smoothing part.........
You are using Centos 5 which is deprecated so nothing in yum will work until you follow this post to use the vault:
http://realtechtalk.com/Centos_59_Working_Vault_Repo_file-1921-articles
yum update
Loaded plugins: fastestmirror
Loading mirror speeds from cached hostfile
* epel: fedora-archive.ip-connect.vn.ua
Traceback........
mysqldump or mysql query of a larger file/table
ERROR 2006 (HY000) at line 567: MySQL server has gone away
Add this to /etc/my.cnf
max_allowed_packet=64M
service mysqld restart........
This happens if you are running a kdenlive script from the shell of a remote machine without using SSH "-X" forwarding and it will also cause any areas where you write text to be a white screen for that duration.
melt FusionFestival.kdenlive
No LADSPA plugins were found!
Check your LADSPA_PATH environment variable.
[producer_xml] failed to load transition "qtblend"
[producer_xml] failed to load transition &q........
When using the .sh script the rendering doesn't work after an upgrade of related packages to kdenlive.
kdenlive (kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1)) with affine or composite transitions was fine but is now broken during the time of transition it is just a white screen.
The previous version was fine:
kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1
But now I can't find it or install it:........
[1035724.274610] [drm:intel_pipe_update_end [i915_bpo]] *ERROR* Atomic update failure on pipe A (start=62076478 end=62076479) time 102 us, min 894, max 899, scanline start 893, end 900
W: Possible missing firmware /lib/firmware/i915/kbl_dmc_ver1.bin for module i915_bpo
I've been getting those errors on a J3455 NUC box with the latest kernel on Linux Mint 18.2. When updating the initramfs I also got the error about the firmware........
If you were in my boat you were frustrated that you had to double encode, eg. one separate encode for watermark and a separate from concat and it's not easy to figure out this with ffmpeg on your own. However it is a nice way to save time!
ffmpeg -i file1.mp4 -i file2.mp4 -i file3.mp4 -i watermark.png -filter_complex "[0:v]setpts=PTS-STARTPTS[v0]; [1:v]setpts=PTS-STARTPTS[v1]; [2:v]setpts=PTS-STARTPTS[v2]; [v0][0:a][v1][1:a][v2][2:a]concat=n=3:v=1:a=1[v][aout]; [v][3:........
When things go wrong your video is basically unplayable or the first video plays fine and then freezes when moving on to the next. Generally if both videos weren't produced with the exact 100% same settings you will have issues. You can try the basic concat but it often won't work right.
Solution for me:
My example uses 3 videos in total so "n=3" and a=1 to include audio.
ffmpeg -threads 12 -i file1.mp4 -........
I believe from what I've read that this card's driver doesn't support the features after trying all known troubleshooting methods.
ffmpeg -i uservideoRendered.mp4 -filter:v hwupload_cuda,scale_npp=w=1920:h=1080:format=nv12:interp_algo=lanczos,hwdownload -c:v hevc_nvenc -profile main -preset slow -rc vbr_hq -c:a copy uservideoRendered.mp4-test
ffmpeg -i uservideoRendered.mp4 -filter:v hwupload_cuda,scale_npp=w=1920:h=1080:format=nv12:interp_algo=lanczos,hwdownload........
Essentially a program I was running for mining did not terminate properly with Ctrl+C it is listed as defunct and cannot be killed, kernel is tainted and normal tricks to disable the port are impossible the dev and sys entries for the device cannot be browsed or interacted with in any form without a lockup of the request. The only solution is to reboot due to the kernel taint as far as I can find so far.
[1130246.811056] INFO: task minerd:21861 blocked for more th........
#if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used
wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2
tar -jxvf ffmpeg-3.3.2.tar.bz2
cd ffmpeg-3.3.2/
./configure --disable-yasm
install prefix /usr/local
source path ........
Done on Centos 7.3 very important as clearly based on older guides it was a lot easier and more simpler! Hint do not use grub2-install!
If you have trouble booting after this check this CentOS mdadm RAID booting/fixing guide.
One huge caveat if you are an oldschool user or sysadmin who has avoided UEFIbooting
The nor........
This is a 8TB Seagate external USB 3.0 device apparently newer kernels use a module called "UAS" instead of "USB Storage" which causes issues as a lot of devices are not properly supported in UAS mode by the kernel driver. The solution some say is to disable UAS specifically for your USB device but I'd rather just disable UAS altogether.
Solution blacklist UAS: *do not do this it does not work and just causes your USB 3.0........
When running cudaminer once it tries to initialize the card the entire screen freezes. The computer itself is still running but the Xorg is done for, you cannot even switch to another console window and must reboot (even an mdm or Xorg restart does not help).
At first cudaminer will give you these errors:
stratrum_recv_line failed
...retry after 15 seconds
GPU #0: Geforce 210 with compute ca........
**** Warning: can't process font stream, loading font by the name.
Can't find CMap Identity-UTF16-H building a CIDDecoding resource.
Warning: falling back to Identity ordering
**** Error reading a content stream. The page may be incomplete.
**** File did not complete the page properly and may be damaged.
**** This file had errors that were repaired or ignored.
****........
Here is a simple MP3 player and now there's a reason to understand why the supplied cable has some kind of capacitor and is very short. These devices can be VERY finicky and any voltage fluctuation or difference is enough to cause issues.
Take for example the error messages from Linux Mint:
[804829.895414] usb 1-1: USB disconnect, device number 11
[806961.109030] usb 1-1: new high-speed USB device number 12 using xhci_hcd........
Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Missing folder chosen by user:
Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Removed missing file: MAH02949.MP4
Jun 1 15:45:57 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: ui_util:WARNING Icon theme media-playback-start not found. Will use backup........
These errors believe it or not are simply because of not being the root user or running with sudo! However if you didn't know to try as root you'd think there was a problem with your burner or disc Essentially it looks like without root you cannot send the required scsi commands to continue writing. Ithink cdrecord should have built-in tests or safeguards to see if it has the permissions to run the required commands.
I guess for more advanced users the idea is simila........
*Update so this doesn't work it must be something to do with the path of nfs or something else but the installer fails with "Installer crashed" at the end whereas with the CD/USB it works.
This assumes you've already installed and configured a separate PXE/DHCP server somewhere else and your /tftpboot directory is setup.
This is for Linux Mint 18.1 but generally applies to most versions although you may have tro change things like "casper"........
If you have this problem: http://realtechtalk.com/mencoder_bmovl_error_vf_bmovl_Unknown_command_Ignoring_-1860-articles
Then ffmpeg is for you. Go here if you are using Linux Mint and cannot find or install it to use an external PPA........
Based on this tutorial: http://www.linuxjournal.com/content/overlay-images-video-using-mplayer-and-mencoder
mencoder -oac pcm -ovc raw -vf bmovl=0:0:tfifo -o $output $file
vf_bmovl: Unknown command: ''. Ignoring. ........
This is very annoying that ffmpeg is missing from Linux Mint! They have ffmpeg2theora which is a totally different codec and does not work as ffmpeg does at all (it is basically totally different).
However on Linux Mint 17 I was able to use a Ubuntu PPA and sucessfully install ffmpeg!
https://launchpad.net/~mc3man/+archive/ubuntu/trusty-media
Adding this PPA to your system........
Using Apache 2.2 and PHP5.6 PHPBB3 is very slow to respond. Actually for some reason it takes so long to even register a log entry in access_log as in several seconds or a few minutes later it shows up in Apache. All other vhosts and Apache access stops working and freezes until the request to access PHPBB3 slowly completes.
It seems to randomly be slow if you stop using it whether for posting or reading the forums. I've migrated to different machines including........
This error is commonly due to Java security or TLS settings but there is a second issue with forwarded ports that also causes it.
1. Java Security/TLS Settings issue:
This article has the solution to change them all in Linux automatically
2. Port Forwarding Issue if your Avocent DSR is behind NAT/private IP........
Centos 7 is no cakewalk, there are many fundamental features and basic utilities that are missing or even completely renamed or different!
Another shocking thing is to check your NIC it is set by default to not turn on when booting!
And by the way there is no more standard eth0 the NIC convention is now "enp0s3"
vi /etc/sysconfig/network-scripts/ifcfg-enp0s3........
gpick is a great and simple tool now that I now how to use it
sudo apt-get install gpick
The trick is to find "the swatch"
I was in a rush and was frustrated that it wouldn't work how Iexpected and I had to memorize the hex code of the color my mouse was over.
There is something it tells you to do which is "Click on the swatch area" (click onthe honeycomb graphic area that is the s........
1.) Replicate the number of partitions in your new drives.
gdisk /dev/sda
gdisk /dev/sdb
I created 3 partitions of the same same size.
partition #1: +1G (/boot)
partition #2: +60G (swap)
partition #3: rest of it (/)
#note if you are using GPT/gdisk you need to create separate a partition at least 1MB in size (in my case I would a 4th partition and mark it type ef02).........
The solution is simply "tidy"/Tidy-HTML. It will take your poorly formatted HTML code (and I mean files that span just a few lines that are unreadable) and fix it up.
Note the command below does everything in place. *Make sure you take a backup of all .html files*
It also seems to break html5 code/templates so beware.
tidy -im yourfile.html
An automated way in bash:........
Could not retrieve mirrorlist http://mirrorlist.centos.org/?release=6&arch=x86_64&repo=os error was
12: Timeout on http://mirrorlist.centos.org/?release=6&arch=x86_64&repo=os: (28, 'Operation too slow. Less than 1 bytes/sec transfered the last 30 seconds')
Error: Cannot find a valid baseurl for repo: base
You would think this should be fine and simple like using a proxy with most other software?
However........
Get the python "warc extractor" from here. WARC just seems to be such an unnecessary and complicated format. Why not use tar, rar, zip etc...?
./warc-extractor.py -dump content !http:content-type:pdf yourfile.warc........
This was a surprising bug but I unplugged all drives for an array md127. At first it was just 1 drive and mdadm seemed to notice this. I unplugged the second drive taking the array offline but mdadm did not realize it was offline and still showed a non-existent disk as being part of it. This created problems trying to unmount it or even to stop this array with mdadm freezing.
As for how to fix it I can only think of making sure you are not in a mounted path of........
The solution is simple but strange, if you copy your /var/lib/mysql directory to another server and think it will work, be sure to check if you have /var/log/mysql and binary log files. If you do, the server will not work and will give you errors like below and crash without the proper log files.
UPDATE user SET password=password("newpass") WHERE user='root';
flush privileges;
ERROR 2013 (HY000): Lost connection to MySQL server durin........
Change Host="192.168.5.99" with the remote IP allowed(this is of course more secure but also cumbersome if your IP changes). You could also have a single layer of protection that specifies the IP via firewall or both (of course both are far mor secure).
UPDATE user SET Host="192.168.5.99" where Host="localhost"
or for any/wildcard
UPDATE user SET Host="%" where Host="localhost&qu........
I created a new partition table on a newly plugged in device and it caused fdisk to hang (even force kill does not work). It also may be a bad drive or some other issue because fdisk -l hangs after the first 2 HDDs (totaly of 8 HDDs on this system):
[1232879.903596] INFO: task fdisk:27176 blocked for more than 120 seconds.
[1232879.903607] Tainted: P&nbs........
iptables -t nat -A OUTPUT -m addrtype --src-type LOCAL --dst-type LOCAL -p tcp --dport 3306 -j DNAT --to-destination ip.ip.ip.ip
iptables -t nat -A POSTROUTING -m addrtype --src-type LOCAL --dst-type UNICAST -j MASQUERADE
sysctl -w net.ipv4.conf.all.route_localnet=1
Make sure you substitute "ip.ip.ip.ip" for your real public IP and also the "--dport 3306" for the port you want to forward.
Finally run the sysctl command and........
M4A is a weird format, so you have to be creative here is a quick copy of what I did.
Basically you need to convert to .wav to make use of them and thenI converted the resulting .wav into an mp3 (nice small file size and basically universally playable):
=======
sudo apt-get install mpg321 mp3gain faad normalize lame
faad "Voice 002 (copy).m4a"
faad "Voice 002 (copy).m4a"........
Tired of checking iotop and seeing that your drbd partition is using 99.99% of io all the time and finding your drbd device performs slow in general?
This is especially an issue in versions of DRBD in the 8.3 tree in particular one documented case is on "8.3.13" but it likely applies to other devices.
The symptoms are that resyncing is fine and normal but any reasonable amount of activity is very slow and lagged and creates a high server load and con........
migrating from an old OpenVZ (Centos 5) to new OpenVZ (Centos 6)
Also if migrating from 32-bit HN to 64-bit your RAM will probably be much bigger than it should be!
16x bigger
eg. 32bit HN:
total used free shared buffers cached
Mem:&nb........
I have not found the source of this but essentially it seems like drbd and ext4 may not play well but I have to confirm still.
In either case an older DRBD setup with older hard drives seems to have little to no iowait, but the main difference is the drbd partition is ext3 and not ext4. I will experiment and see if that fixes this, then we will know that DRBD and ext4 have issues.........
This happened while an mdadm array was syncing, all access from writing a new blank file to opening a small .txt file was very slow:
[222117.312078] kjournald starting. Commit interval 5 seconds
[222117.685060] EXT3-fs (md0): using internal journal
[222117.685096] EXT3-fs (md0): mounted filesystem with ordered data mode
[222122.376847] kjournald starting. Commit interval 5 seconds
[222122.602825] EXT3-fs (md2): using internal jour........
In Firefox I cannot connect to any website, proxy is disabled and outside network access is confirmed, no system or manual proxy was set on this Linux Mint/Ubuntu system. Normally this can be caused by proxy or DNS problems and the weird thing is that traceroute and ping to other IPs worked fine but even connecting to sites by IP was not working.
The connection was reset
The connection to the server was reset while the page was loading.........
pip install obfsproxy
/usr/lib/python2.6/site-packages/pip/_vendor/requests/packages/urllib3/util/ssl_.py:90: InsecurePlatformWarning: A true SSLContext object is not available. This prevents urllib3 from configuring SSL appropriately and may cause certain SSL connections to fail. For more information, see https://urllib3.readthedocs.org/en/latest/security.html#insecureplatformwarning.
InsecurePlatformWarning
You are using pip version 7.1.0, however version 8.1.1 i........
Download from here http://www.avagotech.com/products/server-storage/host-bus-adapters/sas-9200-8e#downloads
sudo Installer_P20_for_Linux/sas2flash_linux_i686_x86-64_rel/sas2flash -listall
LSI Corporation SAS2 Flash Utility
Version 20.00.00.00 (2014.09.18)
Copyright (c) 2008-2014 LSI Corporation. All rights reserved
&nbs........
I have two lines on my PAP2T and the only thing that solved this problem rather instantly was to change the line with the problem to using port 5060 instead of 5061 (so both lines are using port 5600). Note that I am not forwarding either port in my router either.
Some of the symptoms of this problem for me were the following:
No dialtone or it would take several tries.
You answer a call but the phone keeps ringing (takes a few times t........
service iptables start
iptables: Applying firewall rules: iptables-restore: line 40 failed
[FAILED]........
1.) Flash directly to this file:
http://tomato.groov.pl/download/K26RT-N/build5x-132-EN/Linksys%20E-series/tomato-E2500-NVRAM60K-1.28.RT-N5x-MIPSR2-132-Max.zip
*I was never able to get the larger "Mega" file to work, at least not initially so I recommend the file above.
To enable 5ghz I had to do the "Clear NVRAM" Option before it was shown.
2.) Or if you don't need 5ghz (most devices do not support it and cannot........
The problem is that the default of most of these units is set for non-North American phones so the ring sounds like it cuts off and is not sequential.
How To Fix the Issue
Click on "Regional" and make sure you are in Advanced mode.
........
The Scenario
You have dual NICs and you disable NIC1 which uses 192.168.1.1 as its gateway. With NIC2 you enable it/connect it to another network which also has the gateway 192.168.1.1
Everything will work fine at this point.
When switching back to NIC1 even with NIC2 disabled and even unplugged, the OS basically can't pick up the new/updated ARP entry of the old device for 192.168.1.1 and perhaps thinks it is a security risk or spoof of some sorts and blocks i........
This is a real pain because I had to manually unplug ethernet cables for network testing or to use an alternate network or guarantee physical access to one network segment is cut off.
For some reason this happened after Ikilled dbus because it was confused and blocking packets thinking they were coming from the wrong interface since eth0 and eth1 both had the same subnet and gateway.
I eventually did a "service network-manager restart" but the option was........
The following assumes the computer is local/physical to you and/or it always has a LANIP so it can be accessed on site without having a default gateway.
The key to this is not to set a default gateway for your computer or you can set a script on boot or other time to delete the gateway (where eth0 is the NIC you are using):
route del default eth0
50.80.20.2 is the VPN server you connect to
192.168.1.1 is your........
I was asked to troubleshoot why a site wasn't loaded or responding properly, it turned out they were using some old javascript tracker from Bing/Microsoft that is no longer valid or working. You have to wait forever for it to time out but it really did disrupt the functionality of a very important site:
flex.atdmt.com
If you have the above code in javascript on your site remove or comment it out.........
In this case we want to mount partition #2
fdisk -lu Centos-6.6-x86_64.img
You must set cylinders.
You can do this from the extra functions menu.
Disk Centos-6.6-x86_64.img: 0 MB, 0 bytes
255 heads, 63 sectors/track, 0 cylinders, total 0 sectors
Units = sectors of 1 * 512 = 512 bytes
Device Boot&nbs........
It sounds like this is corrected in later versions of the OpenVZ kernel but Iam not sure, it may also be that a much newer kernel is needed and Centos may not have a recent enough kernel.
*Debain 7.0 however does work fine as a temporary fix or work around.
Debian 8 OpenVZ no IP and networking not working:
lo Link encap:Local Loopback
 ........
Here is the scenario you or a client have a remote machine that was installed as a standard/default minimal Centos 6.x machine on a single disk with LVM for whatever reason. Often many people do not know how to install it to a RAID array so it is common to have this problem and why reinstall if you don't need to? In some cases on a remote system you can't easily reinstall without physical or KVM access.
So in this case you add a second physical or disk or already ha........
#solution
Edit /etc/yum.repos.d/openvz.repo
For the first two entries comment out #mirrorlist and uncomment #baseurl and then it worked
openvz yum problem Centos 6.5 cannot find file on mirror:
yum update
Loaded plugins: fastestmirror
Determining fastest mirrors
* openvz-kernel-rhel6: mirrors.ustc.edu.cn
* openvz-utils: mirrors.ustc.edu.cn
base ........
Iwas surprised to see that Linux Mint at the latest 17.2 version still has NO mdadm installer option, and worse the installer will not be able to create a proper booting environment even when you do install it.
How to setup mdadm in Linux mint LiveCD
sudo su
apt-get install mdadm
# partition as you need and then create your mdadm devices
# create your SWAP md0
mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/sda1 /d........
First of all this seems to apply to many ONVIF devices
Hard coded IP: 192.168.1.10 (yes not kidding no DHCP!)
00:12:12:9C:C2:00
To view RTSP stream use VLC, or openRTSP or other RTSP capable software:
rtsp://192.168.1.10/user=admin_password=tlJwpbo6_channel=1_stream=0.sdp
user: admin
password: blank
http://ip/Login.htm
Uses Quicktime and is a poor quality picture and slow
Cannot change pass........
yum -y install wget
wget -P /etc/yum.repos.d/ http://ftp.openvz.org/openvz.repo
rpm --import http://ftp.openvz.org/RPM-GPG-Key-OpenVZ
yum -y install vzkernel vzctl
#enable ip_forward
sed -i s/'net.ipv4.ip_forward = 0'/'net.ipv4.ip_forward = 1'/g /etc/sysctl.conf
#all interfaces should not send redirects
echo "net.ipv4.conf.default.send_redirects = 1" >> /etc/sysctl.conf
echo "net.ipv4.co........
If you get that message it means you have inserted the adapter or device incorrectly. In my case the adapter needed to be at the rear end of the pins and it caused this message.
Do not ignore this message as it may appear to work but you will get errors and in reality your chip will not be erased or programmed even if it appears like it is working.........
mdadm --create /dev/md1 --level 10 --raid-devices=2 /dev/sdb2 /dev/sdc2 --layout=f2 --metadata=0.90
Note that layout=f2 or layout=n2 is very important as without it you'll get a complaint like this:
mdadm --create /dev/md0 --level 10 --raid-devices /dev/sdb1 /dev/sdc1 missing missing
mdadm: invalid number of raid devices: /dev/sdb1
It is basically more like a prop........
Use netstat with the -anpe option. The e option shows the inodes and I do not know if it will always work or if it was by fluke but I was dealing with dozens of SSHsessions and needed to know which session was related to which forward (the PIDs of the SSHand SSHD did not match etc...)
Notice the "59560675" and "59560762" those are almost identical, if you find two sets that are nearly identical except for the last 3 digits they may match (in my ca........
Message from syslogd@server at Sep 14 11:35:59 ...
kernel:[Hardware Error]: MC4 Error (node 1): DRAM ECC error detected on the NB.
Message from syslogd@server at Sep 14 11:35:59 ...
kernel:[Hardware Error]: Error Status: Corrected error, no action required.
Message from syslogd@server at Sep 14 11:35:59 ...
kernel:[Hardware Error]: CPU:6 (10:8:0) MC4_STATUS[Over|CE|MiscV|-|AddrV|CECC]: 0xdc00400021080813........
Avocent Unable to load resource avctVideo.jar
Avocent requires port 80 and 443 to be forwarded or you will get a message like above if it's on a NAT network and you are accessing it from the outside (internet).........
iptables -t nat -A PREROUTING -p tcp -m multiport --dports 80,443,2068,8192 -j DNAT --to-destination 192.168.1.175
Just adjust the "--dports" to the ports you need and the --to-destination to the destination IP (note it must be on the same network as the server running iptables........
-------------------------------------
ProCurve J4903A Switch 2824
Software revision I.10.77
Copyright (C) 1991-2009 Hewlett-Packard Co. All Rights Reserved.
RESTRICTED RIGHTS LEGEND
Use, duplication, or disclosure by the Government is subject to restrictions........
Fortunately the format is EATX so an EATX case will work and the screw layout is standard.
You will need to remove the HEX/TORX screws that are connecting the stock HP standoffs (meant to slide into an HP case).
XW9400 Motherboard Issues
Size: 12" x 13"
Proprietary Power Connector
Proprietary CPU Power Connector
Proprietary Memory Power Connector
Fan connectors are 4 pin so you will need some kind of adapter.........
Motherboard: Gigabyte GA-3CESL: http://b2b.gigabyte.com/products/product-page.aspx?pid=2658#dl
Dell Part Numbers for the motherboard: R1232 R1232L R2232S SERVER MOTHERBOARD GENUINE 408P9 CN-0408P9
GA-3CESL Manual Download here
RAMSlots: 16 (8 controlled by each CPU)
RAMType: DDR2 ECC 5300P........
This command rips the audio tracks to .wav files
*I recommend making a new directory with the name of the audio disc first and executing everything from within that directory below.
cdparanoia -B
Use the lame mp3 encoder to encode each one with this script:
*Note that this will encode any other files ending in "cdda.wav"
for track in `ls *cdda.wav`; do lame -b 192 $track; done........
so in this case we have files named like this:
track01.cdda.wav.mp3 track06.cdda.wav.mp3 track11.cdda.wav.mp3
track02.cdda.wav.mp3 track07.cdda.wav.mp3 track12.cdda.wav.mp3
track03.cdda.wav.mp3 track08.cdda.wav.mp3 track13.cdda.wav.mp3
track04.cdda.wav.mp3 track09.cdda.wav.mp3
track05.cdda.wav.mp3 track10.cdda.wav.mp3
but we want to rename them so they are like "05.........
windows cannot find the microsoft license terms windows 2012 server install
This is actually because you are using less than 576MB of RAM. In my case I was installing on a KVM VPS with 512MB of RAM. This issue would apply to any physical or virtual server with less than 576MB of RAM. This includes Virtualized VPS Servers with XENHVM, KVM, VBOX, VMWare etc.. or Dedicated Servers with such little RAM.
It's very misleading of course since it has not........
[ 17.208336] tg3 0000:08:00.0: eth0: Link is up at 1000 Mbps, full duplex
[ 17.210194] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX
[ 76.000065] phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
[ 76.002332] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 86.736004] eth0: no IPv6 routers present
[ 148.960038] phy0 -> rt2x00lib_request_fi........
Install the "Flashblock" plugin because we all know most unwanted high CPU usage situations come from the browser usually because of a looping Flash ad taking up 100% CPU.
The solution is to install the "Flashblock" plugin that doesn't allow any Flash to load and play unless you click on the placeholder.........
If the below is happening on KVM (a very weird and scary looking error) it's probably because of Windows. This has happened countless times to me where the bootsector on Windows 7/2008 becomes corrupted easily (even by a crash or shutdown).
KVM: unknown exit, hardware reason 0x80000021
kvm_run returned -22
rax 0000000000000010 rbx 0000000000000080 rcx 0000000000000000 rdx 0000000000000080
rsi 000000000025db2a rdi 000000000007db2a rsp 0000000000000200 rbp........
It's a basic script that reads the file "ips.txt" in the current directory and then creates a corresponding ifcfg file
#!/bin/bash
GATEWAY=192.168.1.1
NETMASK=255.255.255.0
device=eth0
counter=0
for ips in `cat ips.txt`; do........
i337 Canada on Bell is hard to root or even install TWRP
Installed TWRP from Odin and my computer gave me the bluescreen at the end but it seemed to be successful (after ODIN said reset).
TWRP mode does not seem to enter, instead you get the Android recovery mode with Volume up + Home
http://galaxys4root.com/galaxy-s4-root/how-to-root-att-or-verizon-galaxy-s4-on-android-4-4-2/
1.)........
It really seems that 4.4.4 is not ready or stable for the i717 yet and this makes sense since it takes a lot of work/development and testing to get the factory stock ROMs working well. In the end I used the 4.1.2 based Blackstra BlackJelly because it was fast, stable and just works and feels great. The aftermarket support is great but many devs are focussed on adding features and customization that most of us don't want or need rather than getting things smooth and stable.........
CPanel says you can access 98% of the functions through CLI which experienced Unix/Linux admins prefer for simplicity and for scripting. I've never found CPanel easy to use from the admin panel, it seems everything is hard to find and a simple task becomes a series of hunts.
So for people like me here's the list: http://cpanel.net/system-administrators/command-line-scrip........
-A PREROUTING -d 98.98.98.5/32 -p tcp -m tcp --dport 1050 -j DNAT --to-destination 192.168.1.50:3389
The above forwards port 1050 on IP98.98.98.5 to 192.168.1.50 port 3389 (you can obviously edit things to meet your needs).........
I used the matching 8.3.13 utilities and it didn't work but strangely the newer 8.3.16 which makes DRBD complain works just fine.
GIT-hash: 83ca112086600faacab2f157bc5a9324f7bd7f77 build by root@sighted, 2012-10-09 12:47:51
0: cs:SyncSource ro:Secondary/Primary ds:UpToDate/Inconsistent A r-----
ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:b oos:5236960
&am........
c1: warnings being treated as errors
stonith_signal.h:34: error: 'stonith_signal_set_simple_handler' defined but not used
gmake[3]: *** [apcmaster.lo] Error 1
gmake[3]: Leaving directory `/root/rpmbuild/BUILD/heartbeat-1.2.4/lib/plugins/stonith'
gmake[2]: *** [all-recursive] Error 1
gmake[2]: Leaving directory `/root/rpmbuild/BUILD/heartbeat-1.2.4/lib/plugins'
gmake[1]: *** [all-recursive] Error 1
gmake[1]: Leaving directory `/root/rpmbuild/BUI........
"Detecting hardware, please wait..."
Solution
This occurs if you are installing with low RAM such as 128MB
Bump it up at least to 512MB for the install........
This problem seemed to happen recently but was likely causing issues before where the phone(s) do not ring.
Now there are a few reasons why this can happen especially if your adapter has DND mode enabled (disable it).
However that wasn't my issue and Ionly figured it out the other day when by fluke if you're on the phone (making a call) then calls will come in.
That's when Ifigured out the solution:
This likely app........
./configure
./configure: line 91: cd: /lib/modules/2.6.32-042stab084.25/build: No such file or directory
Error: kernel version not found.
Please make sure your kernel is configured.
dr-xr-xr-x. 4 root root 4096 Feb 21 06:13 ..
lrwxrwxrwx 1 root root 45 Feb 21 06:13 build -> ../../../usr/src/kernels/2.6.32-042stab084.25
drwxr-xr-x 2 root root 4096 Feb 12 20........
yum -y install wget
wget -P /etc/yum.repos.d/ http://ftp.openvz.org/openvz.repo
rpm --import http://ftp.openvz.org/RPM-GPG-Key-OpenVZ
yum -y install vzkernel vzctl
After that just reboot and you may also have to enable ip_forward in /etc/sysctl.conf........
Error: Package: php-Monolog-dynamo-1.7.0-1.el6.noarch (epel)
Requires: php-aws-sdk
Error: php-pecl-zendopcache conflicts with 1:php-eaccelerator-0.9.6.1-1.el6.x86_64
Error: php-xcache conflicts with php-pecl-apc-3.1.9-2.el6.x86_64
Error: php-pecl-zendopcache conflicts with php-pecl-apc-3.1.9-2.el6.x86_64
Error: Package: php-horde-Horde-Vfs-2.1.2-2.el6.noarch (epel)
&n........
ssh -L 5905:localhost:5900 root@yourserver.com
The "-L" means to create a port forward to a port on your server.
The 5905 means the port on your computer that will be used to access the port 5900 on the remote server.
localhost is the IP that you use to access the port forward (you can change it to 0.0.0.0 which will be all IPs on your system/computer but localhost is good for security and privacy unless a whole network of people need access).........
[3805108.257042] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
[3805108.257052] sd 0:0:0:0: [sda] Write Protect is off
[3805108.257054] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[3805108.257066] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[3805108.257083] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
[3805108.257090] sd 0:0:0:0: [sda] Write Protect is off........
I was having an issue with only certain random/jpeg files with the functions imagecreatefromjpeg imagecreatetruecolor and other related ones.
This issue was annoying basically it seems like a libgd issue/bug with newer versions of PHP and it was difficult to trace-out. One very useful thing that helped me was using "php-cgi" and passing the query string as an argument eg:
php-cgi images.php source=IMG.jpg (that way you get all the error messages wh........
This server has been running for weeks without issue, it's currently only using 1 of 2 CPUs as it is running in the office as a test bed (mainly due to the handle 12 bay storage/great for testing HDDs). The errors below seem to mainly be from AMD CPUs, it's only happened a single time and in the days since Igot that error it hasn't occurrred.
Interestingly enough /proc/cpuinfo still shows all 4 cores of the CPU (Opteron 2373 Quadcore HE) and the functionality doesn't seem........
Here is a handy script that will check all processes and report what is swapping
#!/bin/bash
for pid in `ps x|awk '{print $1}'`; do
result=`cat /proc/$pid/status|grep VmSwap|awk '{print $2}'|grep -v ^"0"`
if [ ! -z "$result" ]; then
programresult=`ps x|grep $pid|grep -v grep`
if [ $? == 0 ]; then
program=`echo $programresult|awk '{print $5}'|grep -v ^grep`........
mount -o bind /proc /sda2/proc
mount -o bind /dev/ /sda2/dev
mount -o bind /sys /sda2/sys
chroot /sda2
mint / # mount -o bind /proc /sda2/proc
mint / # mount -o bind /dev/ /sda2/dev
mint / # mount -o bind /sys /sda2/sys
mint / # chroot /sda2
mint / # cd ~
mint ~ # ls
Desktop
mint ~ # cd /
mint / # ls
bin Desktop dev-temp home&nb........
Linux box13. 2.6.32-042stab076.5 #1 SMP Mon Mar 18 20:41:34 MSK 2013 x86_64 x86_64 x86_64 GNU/Linux
even setting privvmpages to a specific setting DOES not affect "free -m" in containers.
This is probably a kernel issue
23:36:29 up 159 days, 7:12, 4 users, load average: 0.42, 0.44, 0.33
[root@box13 ~]# free -m
total&n........
The units in echo are kB as in kilobyte.
Setting a high sync speed
echo 120000 >/proc/sys/dev/raid/speed_limit_min
This will increase the speed, note that sometimes a rebuild is slow due to current disk activity/iowait.
If that is not the cause then you may have a hardware issue (controller, cable or a bad drive).
Setting a lower sync speed
echo 1200 >/proc/sys/dev/raid/speed_limit_max........
02:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1068E PCI-Express Fusion-MPT SAS (rev 08)
03:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1068E PCI-Express Fusion-MPT SAS (rev 08)
Basically these cards are a stripped-down version of Dell Perc 6/i only they (SAS 6/ir) support JBOD.
The DellPerc 6/i are basically useless because it doesn't have JBOD support and requires software or BIOS commands to add or remove........
Install rsync4randroid and in the shell/ssh do this:
ln -s /data/data/eu.kowalczuk.rsync4android/files/rsync /system/xbin/rsync........
I've got one of these for testing projects from work at home and got more than I bargained for with the time I've spent on it due to the storage handing/Perc 6/i cards.
My particular model came with the following:
2U Rack Mount Server with Rails
2xOpteron 2373 EE (Quad Core, there is a 6-core version that can be found at times)
16GB RAM
2 x 250GB Seagate SATA
2 x Dell Perc 6/i (horrible and a nightmare to work........
The results are not bad, the Hitachi performs the same as it does in a SATA2 motherboard. However, the 2TB is much different, on a similar 2TB Toshiba I get about 198MB/s on a different motherboard vs the 2TB Hitachi which should produce similar results.
This Dell Perc 6/i is on a PCI x8 riser card and is connected to a 12-port backplane.
Adapter #0
Enclosure Device ID: 32
Slot Number: 0
Enclosure position: N/A
De........
One thing to remember is that you need MegaCli to do the flashing.
You also need the correct file,I tried at least 2 different Perc 6 firmwares from Dell that kept getting rejected as corrupt by MegaCli(they were really the wrong version). I have an external PCI-E Dell 6 Perc/I butI chose images from the 'Integrated" on motherboard version as it was allI could find. They are different, and below is my first time finding success.........
I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally.
I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli
wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN
--2013-08-26 12:53:39-- http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN
Resolvi........
LSi Megaraid
At first it was configured as a RAID 0, then I deleted the Virtual Disk Group.
I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing.
To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
Say if you need to make a firewall script to block certain ports this works great.
for ports in 21 25 443; do
iptables rules here
done........
Bash weird variable whitespace missing
var=`cat tlds.csv|grep .ca,`
# echo "var=:$var:"
:ar=:.ca,Canada
Why is the v missing in the last line?
It should be
:var=:.ca,Canada
instead of
:ar=:.ca,Canada
I noticed a problem with the file with doing a "cat -v" on it.
Here's the issue, the file contains carat M ^M:
.vg,British Virgin Island........
yum update error
Traceback (most recent call last):
File "/usr/bin/yum", line 29, in ?
yummain.user_main(sys.argv[1:], exit_code=True)
File "/usr/share/yum-cli/yummain.py", line 229, in user_main
errcode = main(args)
File "/usr/share/yum-cli/yummain.py", line 145, in main
(result, resultmsgs) = base.buildTransaction()
&nbs........
kernel: EDAC MC0: CE page 0x0, offset 0x0, grain 1073741824, syndrome 0x1a, row 2, channel 0, label "": i3200 CE
I believe this is a hardware issue, it's usually bad RAM, incompatible RAM or bad timing or even a motherboard/RAM controller.........
This is important if you need public access to internal IPs such as at your office and don't want to use a VPN just to SSHinto different servers:
Below forwards the port "10001" to the IP192.200.5.53 on port 22 (of course adjust it to your needs).
iptables -t nat -A PREROUTING -p tcp --dport 10001 -j DNAT --to-destination 192.200.5.53:22
Remember to enable MASQUERADE on your NAT IPs or they won't be able to talk to the outside world (........
Another new drive bad from the start:
Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen
Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error
Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC }
Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........
This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad.
ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0
ata1.00: irq_stat 0x40000008
ata1.00: failed command: READ FPDMA QUEUED
ata1.00: cmd 60/00:00:........
Once I set a new MAC address everything was fine and finally anything can be pinged etc.., I've had this happen with many clients in different datacenters on different hardware.........
This is useful for developing a lot of applications, I'm putting it here to keep it handy for myself and hopefully others:
Choose CountryCanadaJapanUnited StatesUnited KingdomAfghanistan........
This is something many people and especially businesses worry about, or at least they should. Before throwing away a hard drive, returning a hard drive, or especially Warrantying/RMAing it, you should wipe the drive.
Linux provides the "shred" and "dd" utlities which work quite well. It seems even a single pass is good enough but by default shred will do 3 passes.
Here's an example of using shred in Linux (I use a custom made distribution from........
If you move your hard drive(s) around to other computers/servers, you'll find that your eth0 keeps getting higher, the first time it will become eth1 and then eth2 etc and even higher if your server has dual or quad NICs. The reason is that udevd basically assigns eth0 tot he first NIC it finds and remembers it, if it encounters a NIC with a differentMAC, it assigns it one higher (eg. eth1).
See the example below, I have eth2 now so how doI fix it?........
Client Log
OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008
debug1: Reading configuration data /etc/ssh/ssh_config
debug1: Applying options for *
debug1: Connecting to 192.168.1.253 [192.168.1.253] port 22.
debug1: Connection established.
debug1: permanently_set_uid: 0/0
debug1: identity file /root/.ssh/identity type -1
debug1: identity file /root/.ssh/id_rsa type 1
debug1: identity file /root/.ssh/id_d........
Kernel panic - not syncing: Attempted to kill init!
Pid: 1,comm: init Tained: G I------------- 2.6.32-358.el6.x86_64 #1
Call Trace:
[] ? panic+0xa0/0x16f
[] ? do_exit+0x862/0x870
[] ? fput+0x25/0x30
[] ? do_group_exit+0x58/0xd0
[] ? sys_exit_........
vgchange -ay
3 logical volume(s) in volume group "vg_12" now active
lvscan
inactive '/dev/vg_12/lv_root' [144.04 GB] inherit
inactive '/dev/vg_12/lv_home' [1.00 GB] inherit
inactive '/dev/vg_12/lv_swap' [7.85 GB] inherit........
Here's the link to the warranty checker and from there you can also create an RMA:
https://myapps.taec.toshiba.com/myapps/admin/jsp/webrma/addRequest1NoLogin.jsp
Note that the serial# shown in SMART is not complete as is the case for many other brand sof HDDs.
For example a 2TB Toshiba shows the following Serial Number in SMART:
Device Model:........
I chose this because I heard a lot of stories about scams and that many providers I contacted said they can't unlock the Canadian I717s (one said "my Bell server" is down).
This method worked perfectly on my Bell I717M and should work for all I717 in Canada, I was able to insert a foreign SIMcard. This will work abroad too but remember entering CWM mode is different for I717's in other countries (at least theUS).
Step 1 - Root + CWM........
Here's a proven example of what a bad hard drive can do, it was technically functioning OKin a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application. The truth is that this failing 1TBHitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..). After swapping it out, tabs change instantly, emails are not lagged, and........
Here's what SMART tells me the serial number is:
=== START OF INFORMATION SECTION ===
Device Model: Hitachi HDS721010CLA332
Serial Number: JP2940HQ3ZY7KH
Firmware Version: JP4OA3EA
User Capacity: 1,000,204,886,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is:&nb........
This seems to be a verified bug on KVM with no solution. I wasn't able to get through the installer with Ubuntu 12.04, it would crash while "configuring apt". I was able to install it with Ubuntu 12.10 but it crashes randomly at times.
This happens with the latest Centos 6.3 kernel and KVM package, I even compiled the latest version from the KVM website and used that, but the results are still the same.
Here's some links to discussion about the bugs:........
sensors|head
i5k_amb-isa-0000
Adapter: ISA adapter
Ch. 0 DIMM 0:+115.0C (low = +127.5C, high = +127.5C)
Ch. 0 DIMM 1: +63.5C (low = +127.5C, high = +127.5C)
Ch. 0 DIMM 2: +61.0C (low = +127.5C, high = +127.5C)
Ch. 1 DIMM 0: +65.0C (low = +127.5C, high = +127.5C)
Ch. 1 DIMM 1: +75.0C&........
The example below converts youvm.img into a vdi.
The -O vdi specifies the new format will be vdi but you can use any other valid formats/vice versa.
qemu-img convert yourvm.img -O vdi yourvm.vdi
This is very handy for those who need to switch between virtualization technologies.........
Let's keep this simple, it's horrible, not only is the picture quality horrible (it's not a big deal) but the keyboard input is an issue. You have to type slowly, lightly and carefully otherwise 1-keystroke could end up being dozens of keystrokes.
It's also a confusing unit for many datacenter techs, I've seen these units hooked up wrong and the instructions themselves aren't clear. I had to resort to shipping one to my office and take my phone pictures of the setup for th........
qemu-img create -b centos.5-8.x86.20120308.qcow2 -f qcow2 ../kvmguests/25000-centos5.8x86.qcow2
Formatting '../kvmguests/25000-centos5.8x86.qcow2', fmt=qcow2, backing_file=centos.5-8.x86.20120308.qcow2, size=10485760 kB
-b the source/base image
-f format is qcow2 and the location of the destination image
What is so special about this? It's even quicker than creating a template with OpenVZ but this is an actual OS.
It saves time a........
mdadm --manage /dev/md1 --add /dev/sdb1
mdadm: metadata format 00.90 unknown, ignored.
mdadm: metadata format 00.90 unknown, ignored.
mdadm: metadata format 00.90 unknown, ignored.
mdadm: /dev/sdb1 not large enough to join array
md1's first primary member /dev/sda3 has 57394 cylinders while the /dev/sdb1 has 57393 (1 less cylinder) which is why it won't work.
fdisk -l /dev/sda3
Disk /dev/sda3: 47........
For whatever reason the current OpenVZ yum repo file enables the RHEL6 version of OpenVZ, why is this bad? Because if you're running Centos 5 it still defaults to using the kernel from RHEL6 which won't work on RHEL5/Centos 5.
Ionly realized this after wondering why I couldn't boot into OpenVZ that it was using one meant for RHEL6.
To fix the problem you have to edit /etc/yum.repos.d/openvz.repo and disable the "[openvz-kernel-rhel6]" section by changing........
I backed up everything in the /mnt/sd_card directory thinking that some dataloss could occur for some reason but purposely left my microSDHC unbacked up thinking that "it won't touch that since it's external" and Samsung's and other manufacturers website even say this (that it won't be affected and not to worry etc).
Apparently I was wrong, my microSD was "undetected" and asked to be formatted after the upgrade (there goes 3-months worth of family photos). No........
This may sound silly but there will be conflicts/issues with the default Centos repository so you have to use a third party like remi (I prefer not to do this but it's the only option unless you migrate your sites/data to another server or can stand some downtime-not an option IMHOon a production server).
You may need to upgrade to PHP5.3 to run Joomla or many other reasons.
Your host needs to use PHP 5.2.4 or higher to run this version of Jo........
Error: detected vswap CT config but kernel does not support vswap
This means either old kernel or bad config (physpages NOT set to 0:unlimited)
Solution
vzctl set $veid --physpages 0:unlimited --save........
[ 12.460014] ata1: SRST failed (errno=-16)
[ 17.626677] ata1: link is slow to respond, please be patient (ready=0)
[ 22.480011] ata1: SRST failed (errno=-16)
[ 27.646681] ata1: link is slow to respond, please be patient (ready=0)
[ 38.106817] ata1.01: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80)
[ 48.266676] ata1: link is slow to respond, please be patient (ready=0)........
I've encountered this problem before and I believe it may affect other drivers (I could test but I don't have time). This was happening on my custom Linux system with the pcnet32 driver.
pcnet32: eth0: transmit timed out, status 97fb, resetting (and some other kernel module tracing in dmesg)
Basically it means the card is connected (it shows connected in full duplex etc.. and recognized if the cable is disconnected too) but no packets can be sent or received........
Type "about:config" in your browser and then search for "Quit"
Set these values to true
browser.showQuitWarning
browser.warnOnQuit........
For years I've always built cheap systems believing that there is little difference in more expensive components when it comes to reliability and quality, I generally believe this still except for Power Supplies.
I've always bought cheap cases with nice sounding 350-550W stock/cheap/crap power supplies and haven't had any issues for the most part until recently.
One such case is an NGEAR case with a 550W Optimax power supply, I always read that these supplies don't produce the........
I've thought for awhile that Asus has been banking on its years old reputation for quality amongst gamers and enthusiasts and I think I'm right. My Asus VE247H Monitor with a supposed 2MS refresh rate has 1 red/stuck/dead pixel but fortunately it can only be seen on a non-true black picture or against a blue screen.
I have several Asus products and find they're all of fairly poor quality. First of all their motherboards have given me the most issues of any brand, they te........
I'm running Ubuntu 10.10 with Asus NVIDIA GT430
2.6.35-32-generic-pae #65-Ubuntu SMP Tue Jan 24 14:06:16 UTC 2012 i686 GNU/Linux
Nvidia binary driver: 260.19.06
The screen sometimes completely freezes and locks up or everything starts going very slow:
[1903398.100007] NVRM: os_schedule: Attempted to yield the CPU while in atomic or interrupt context
[1903402.373210] NVRM: Xid (0001:00): 53, CMDre 00000000 00000080 00000000 00000005 00........
fdisk -lu VPS.img
last_lba(): I don't know how to handle files with mode 81ed
You must set cylinders.
You can do this from the extra functions menu.
Disk VPS.img: 0 MB, 0 bytes
255 heads, 63 sectors/track, 0 cylinders, total 0 sectors
Units = sectors of 1 * 512 = 512 bytes
Device Boot Start End ........
I dread updating the kernel and rebooting to find the Ubuntu graphics aren't working and you have to manually intervene. This is usually because Ubuntu for whatever reason didn't update the drivers you need (eg. the manually compiled Nvidia Kernel driver that MUST be recompiled for each and every kernel update unfortunately).
The most common reason may be that "linux-source" hasn't been installed automatically on my system. I tried to manually reinstall the........
I really am a Linux fan but my comments here may not show it. Although I'm quite familiar with Linux CLI to administer servers, I find Linux GUI OS's like Ubuntu at times very clunky.
This is partially because there's no such thing as a "self-made" Linux from scratch where the UIwas designed by a single team. Linux is made up of several different projects that are generally completely separate and this lack of integratiion is a key issue that makes things f........
Failed to initialize monitor device 95% power on
Solution
/etc/init.d/vmware-core start........
It really is as simple as:
cdrecord -v dev=/dev/sr0 pathtoyourisoimage.iso
-v is for verbose, I prefer it but if you don't you won't see as much output like below (I like to know the details and exactly what's happening)
dev=/dev/sr0 specifies the device name of your burner (they say not to use it and to specify some weird annoying device string but using the raw /dev has always worked for me and is how it should have been implemented from the start IMHO)........
These were caused by a bad stick of Corsair RAM
[] free_hot_cold_page+0xfc/0x150
[] __pagevec_free+0x14/0x1a
[] release_pages+0x127/0x12f
[] __pagevec_release+0x15/0x1d
[] __invalid_mapping_pages+0x120/0x156
[........
The first Hitachi Deskstar 2TB 5K3000 drive I bought arrived DOA for whatever reason (not recognized by the BIOS or OS). Perhaps it was shipping since I bought only 1 hard drive. When I bought 4 through another Vendor, all 4 checked out fine.
I was worried about the RMA process because a lot of people have complained about Hitachi taking weeks to send out their hard drive and almost implied the warranty is useless.
I'm happy to report that my experience was great a........
I'll start by showing some problems in the logs:
[2011/08/07 16:22:06, 0] param/loadparm.c:8569(process_usershare_file)
process_usershare_file: stat of /var/lib/samba/usershares/movie failed. Permission denied
[2011/08/07 16:22:06, 1] smbd/service.c:676(make_connection_snum)
create_connection_server_info failed: NT_STATUS_ACCESS_DENIED
That means you don't have permission to access the fi........
ifup eth0
SIOCSIFFLAGS: Cannot allocate memory
Failed to bring up eth0
This is on a Centos 5.5 machine with OpenVZ kernel 2.6.18-238.12.1.el5.028stab091.1PAE, I updated 3 systems with the same hardware to the same kernel and for some reason the network didn't come back.
This only happened once the first time I booted into the new kernel and hasn't happened again but this is a serious issue for those running systems from remote locations such as a datacente........
This may not apply to everyone but here is what happened to me.
One day my IP connectivity for one container went dead, I could ping the hostnode from it and the hostnode could ping it but there was no external routing. I restarted the network service but it didn't help.
I checked the routing table inside the VPS and the host and everything looked normal. Iadded another different IPon the same subnet to the container and it worked. Right away I st........
I had a system running a 128MB live CD image with 2.8 gigs of available RAM and the OOM kernel killer went crazy when using dd for more than 8 minutes and kept killing everything. I've read that this is due to a low-memory issue and paging in the kernel and 32-bit systems with lots of RAM.
I even enabled swapspace on my LiveCD and the issue happened 25 minutes into dd rather than 8 minutes, so what gives?
Also no swap space was ever used!
cat /proc/s........
I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem:
We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........
I had a dying drive that smart thought until it totally disappeared was a good drive, and actually all parameters did look fine but this system was causing my system to lockup and other bad behavior:
=== START OF INFORMATION SECTION ===
Device Model: WDC WD20EARS-00MVWB0
Serial Number: WD-WMAZ20139
Firmware Version: 50.0AB50
User Capacity: 2,000,398,934,016 bytes
Device........
TRACKING DETAILS
PIN xxxxxxxxxxx
Status PLEASE CALL 1 888 SHIP-123 OR 1-888-744-7123 FOR INFORMATION ON THIS SHIPMENT.
I know this is not really tech related but Iorder a lot of hardware on-line these days and once I had a delivery by Purolator.
I didn't get anyone on the phone at Purolator after a few minutes so I gave up, but it turns out that the person on the phone or the system will tell you to........
I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead):
ata1: link is slow to respond, please be patient (ready=0)
ata1: softreset failed (device not ready)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1: link online but device misclassified, retrying
ata1: link is slow to respond, please be patient (ready=0)
ata1: softreset f........
I thought only a faster CPUand SSDwould help but I already have a Quad-Core CPU and it wasn't being maxed out. The actual tests were performed on an AMD-V enabled 128MB dual core VMWare container though.
There is a flag that can be passed to make in order to start multiple threads, by specifying 4 threads I was able to reduce the whole kernel compilation time from scratch by about 50%! (65minutes vs 31minutes!). *Yes I did do a make clean before each co........
You can't just do a straight copy of the VDI image of your virtual machine because there is a unique UUID, wellI believe you can and then you can create a new UUID manually (at least you could with VMWARE) but to keep it clean just use this method:
VBoxManage clonevdi /path/to/your.vdi outputname.vdi
0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100%
That's all there is to it, just wait for it copy and you can th........
If you have a webserver and find you have high IO/lagginess MySQL is one of the first things to check. It turns out MySQL was my problem and it was creating a high load on my server, especially for IO.
How to Enable MySQL Slow Query Logging To Find Slow Performance/Queries
vi /etc/my.cnf
Add this anywhere under [mysqld]
#slow queries
log-slow-queries = /var/log/mysql/mysqlslowqueries.log
long_query_time = 1........
http://www.splitbrain.org/blog/2010-06/15-linux_ocr_software_comparison
They did a great writeup and comparison on the different OCR options available for Linux.........
This happened during a RAID array check:
SMART says both drives pass the test, but I'm doing a long test on them and hopefully this is not a hardware error.
Apr 3 04:22:01 remote kernel: md: syncing RAID array md2
Apr 3 04:22:01 remote kernel: md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc.
Apr 3 04:22:01 remote kernel: md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for reconstruction.
Apr........
My mother needed a new laptop and I recommended her the same one I would have bought myself or my wife, that means the cheapest possible laptop with the most features for the money.
This HP shines at this price point and one thing that made me stay away from buying more and recommending HP/Compaq was the poor battery life. Not anymore, this model has an industry leading up to 4 hours of battery life.
Key Factors for Choosing It:
HDMI Out........
I don't expect this to be solved soon but some of Yahoo's DNS servers are out of whack. I changed the IPs of some nameservers of some domains and now most Yahoo users can't e-mail to those domains!
As you can see below by the "No MX or A records for mychangedomain.com", now Yahoo's DNS/mailserver DNS cache is wrong. You would think they would at least have cached the old incorrect records, but instead for some reason their DNS cache has no entry and doesn't seem........
high IO wait
424 root 39 19 1900 848 552 D 0.0 0.0 0:00.91 updatedb
root 424 0.0 0.0 1900 848 ? DN Mar11 0:00 /usr/bin/updatedb -f sysfs?rootfs?bdev?proc?cpuset?binfmt_misc?debugfs?sockfs?usbfs?pipefs?anon_inodefs?futexfs?tmpfs?inotifyfs?eventp........
Failed to open a session for the virtual machine XP.
AMD-V is being used by another hypervisor. (VERR_SVM_IN_USE).
VirtualBox can't enable the AMD-V extension. Please disable the KVM kernel extension, recompile your kernel and reboot (VERR_SVM_IN_USE)
Solution - Unload KVM module (you can't use two hardware virtualization suites at once)
sudo rmmod kvm_amd kvm........
kernel 2.6.27.54
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
mptbase: ioc0: Initiating bringup
mptbase: ioc0: WARNING - Unexpected doorbell active!
mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000001!
mptbase: ioc0: ERROR - Diagnostic reset FAILED! (102h)
mptbase: ioc0: WARNING - NOT READY!
mptbase: ioc0: ERROR - didn't initialize proper........
I'm posting this because it wasn't easy or obvious how this would be accomplished and the man page leaves it to guesswork.
Multi-line body_checks
Example 1
/........
I bought the 1TB Deskstar C revision recently at just $49 each and put them in RAID 1for my Desktop.
Look at how close the old Deskstar 1TB comes to matching the performance of the mor expensive Samsung and WD's?
This is phenomal, I can't believe the performance I've gotten out of these cheap drives.
http://www.tomshardware.com/reviews/hitachi-western-digital-terabyte,2017-6.html........
I right clicked all applicable cells and chose "number" but that's enough.
I notice when I click the cell there is an invisible ' in front of the number:
'33.64
Calc imported my CSV and decided to add a ' in front of the numeric currency values!!!*Actually the problem occurs when you right click the cells and change the type from text to number, no matter what format you choose.
If I change it to be currency i........
I keep getting messages like this shortly after using the proxy (it works for a few seconds/page loads and then stops):
channel 12: open failed: administratively prohibited: open failed
I'm not sure what the issue is unless there's some kind of hardware firewall on the other end. I've used this exact configuration on multiple servers with no issue and even disabled iptables etc..........
I think this will be useful to others because I have a server that kept crashing mysteriously during intense disk usage/RAID checks. It would only crash during the weekly RAID integrity check.
ThenI noticed during a reboot that not all CPUs were being brought up, as a result this actually creates much higher temperatures with the output I got from sensors, just booting the system produced higher than normal temperatures.
You can imagine that a full blown RAID check........
understanding /etc/aliases
*remember to apply changes you need to run "newaliases" after editing /etc/aliases
one thing I don't get is that it doesn't allow you to specify the whole e-mail address on the left-hand side
eg:
yourfullemail@domain.com: someotheremail@domain.com
postalias: warning: /etc/aliases, line 109: name must be local (if you try the above)
It works more like this:
your........
Forbidden
You don't have permission to access / on this server.
[Sun Jan 23 15:28:12 2011] [crit] [client 96.44.31.12] (13)Permission denied: /www/vhosts/domain.com/httpdocs/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable
Solution
I've done a chmod 755 .htaccess and index.php and restarted Apache
That wasn't the only issue, the issue was the httpdocs direc........
genuine.com/IN: loading master file genuine.com.zone: file not found
_default/genuine.com/IN: file not found
I always found it silly that no one really talks about this and apparently many like me and even control panels like Plesk were still using hard paths. I always thought "why can't I just specify the name of the zone file and have bind find it". Surely the default search path must be /var/named or somewhere else but there is no such thing.........
Jan 16 04:02:03 centosbox syslogd 1.4.1: restart.
Jan 16 04:07:34 centosbox kernel: INFO: task updatedb:20771 blocked for more than 300 seconds.
Jan 16 04:07:34 centosbox kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
Jan 16 04:07:34 centosbox kernel: updatedb D F78BE050 6476 20771 20766&n........
CPU/Kernel/MB/RAID problem?
Jan 5 12:45:05 testbox kernel: [653298.890004] BUG: soft lockup - CPU#0 stuck for 61s! [hal-acl-tool:4168]
Jan 5 12:45:05 testbox kernel: [653298.890005] Modules linked in: vmnet vmci vmmon binfmt_misc drbd video output input_polldev ocfs2_stackglue ocfs2_dlmfs ocfs2_dlm ocfs2_nodemanager configfs k8temp hwmon_vid lp snd_hda_intel snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi........
VMWare bridged adapter not working:
Message from system: The network bridge on device vmnet0 is not running. The virtual machine will not be able to communicate with the host or with other machines on your network. Failed to connect virtual device Ethernet1.
I'm not sure how to fix this but one of the issues is that my eth0 became eth1 after moving my hard drives to a new motherboard. I have run the vmware-config.pl but this did not resolve the issue.........
Webmin Setup Centos 5:
wget http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html&ts=1294339690&use_mirror=surfnet
[1] 24229
[2] 24230
[root@host ~]# --2011-01-06 21:48:20-- http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html
Resolving downloads.sourceforge.net... 216.34.181.........
The normal solution doesn't help or apply here:
ssh -v user@192.168.5.41
OpenSSH_4.3p2 Debian-9etch3, OpenSSL 0.9.8c 05 Sep 2006
debug1: Reading configuration data /etc/ssh/ssh_config
debug1: Applying options for *
debug1: Connecting to 192.168.5.41 [192.168.5.41] port 22.
debug1: Connection established.
debug1: permanently_set_uid: 0/0
debug1: identity file /root/.ssh/identity type -1
debug1: i........
That is pinging to the gateway IP on the same switch, the same IP is pingable externally without any problems which makes me think the switch is fine.
64 bytes from 55.55.55.55: icmp_seq=4 ttl=255 time=1.07 ms
64 bytes from 55.55.55.55: icmp_seq=1 ttl=255 time=3536 ms
64 bytes from 55.55.55.55: icmp_seq=2 ttl=255 time=2536 ms
64 bytes from 55.55.55.55: icmp_seq=3 ttl=255 time=1536 ms
64 bytes from 55.55.55.55: icmp_seq=8 ttl=255 time=1.20 ms
64 by........
I can't tell if it's Flash or Javascript that they were using, but it basically caused my sysetm to lockup until I closed that one page. Is this proof enough that Wal-mart is evil?:)
I've never seen that before, it's weird how certain things mask themselves as high CPU usage with Xorg, unless it is some kind of weird Xorg problem but I believe it's more of a Flash/Javascript issue from Firefox in Wal-mart's evil scripting.........
[137392.910057] ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x80000 action 0x6 frozen
[137392.910077] ata4: SError: { 10B8B }
[137392.910095] ata4.00: cmd 60/20:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 16384 in
[137392.910099] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[137392.910122] ata4.00: status: { DRDY }
[137392.910135] ata4: hard resetting link
[137393.440060] ata4: SATA link........
Go into the directory for your Virtual Machine and delete all ".lck" directories.
rm -rf *.lck
After that your server should boot.........
I've only used it on Centos, soI thought I'd make a quick Debian guide:
Install the DRBD Package
apt-get install drbd8-utils
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following packages were automatically installed and are no longer required:
libswfdec-0.8-0
Use 'apt-get autoremove' to remove them.
The following........
VMWare log: /var/log/vmware/hostd.log
SSL Handshake on client connection failed: SSL Exception
sudo /etc/init.d/vmware-mgmt restart
Stopping VMware management services:
VMware Virtual Infrastructure Web Access
VMware Server Host Agent&nb........
I'm mentioning this because I keep forgetting what port the management is on for the web interface (since newer releases of VMWare server took away the superior stand alone client).
So remember it is port 8333 and sometimes you need to restart vmware-mgmt service and also enable sslv2 in your Firefox or it won't connect.........
I wanted to Import/Use a .vmdk hard disk image file from VMWare. Generally you can just "point" VirtualBox to it and use it and it will work but I found an exception.
One of my Centos 4.4 x64 images wouldn't boot. I had two copies, an older one and the newer one. The older one booted as normal (once I changed the VirtualBox driver to IDE from SATA). The newer one stopped at the "GRUB loading" message no matter what I tried.
As far as........
I separated the 2 drives in the RAID 1 array.
1 is the old one /dev/sda and is out of date, while the separated other one /dev/sdc was in another drive and mounted and used with more data (updated).
I wonder how mdadm will handle this:
usb-storage: device scan complete
md: md127 stopped.
md: bind
md: md127: raid array is not clean -- starting background reconstruction
raid1: raid set md127 active with 1 out of 2 m........
Let the numbers speak for themselves, from what I read the Load_Cycle_Count which is very high (more than 500,000/half a million times) is the number of head parks. What a stupid"Green" design and design flaw which will probably mean an early life for the drive.
This is almost as silly as Seagate's new reputation for BSY/poor quality disks since the 7200.11 series.
To make it worse this is also when Western Digital introduced "Advanced Format" o........
nautilus-gksu - privilege granting extension for nautilus using gksu
nautilus-sendto - integrates Evolution and Pidgin into the Nautilus file manager
nautilus-share - Nautilus extension to share folder using Samba
nautilus-actions - nautilus extension to configure programs to launch
nautilus-bzr - Bazaar (bzr) integration for nautilus
nautilus-cd-burner - CD Burning front-end for Nautilus
nautilus-clamscan - Antivirus scanning for Nautilus
n........
cd /usr/local/directadmin/scripts/
scripts]# ./awstats.sh
--23:49:28-- http://files.directadmin.com/services/all/awstats/awstats-6.9.tar.gz
Resolving files.directadmin.com... 72.35.85.222
Connecting to files.directadmin.com|72.35.85.222|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 1125906 (1.1M) [application/x-gzip]
Saving to: `/usr/local/directadmin/scripts/packages/awstats-6.9.tar.gz'
100%[=........
cd /etc/yum.repos.d
wget http://download.openvz.org/openvz.repo
rpm --import http://download.openvz.org/RPM-GPG-Key-OpenVZ
yum install ovz-kernel-PAE
Now remember to set /etc/sysctl.conf to "net.ipv4.ip_forward = 1"
You can apply the change immediately by running sysctl -w net.ipv4.ip_forward = 1 but remember that you still have to set sysctl.conf
sysctl -p will load and apply any changes to s........
Remember to replace "eth0" with your NIC device although usually it will be eth0.
Replace 192.168.1.1 with your default gateway, remember you can also add multiple gateways by adding a second/different default gateway.
route
Kernel IP routing table
Destination Gateway Genmask&nb........
This has stumped me a few times because I keep forgetting that Centos 5.5 comes with a default iptables configuration that ends up blocking DRBD traffic,I tried all the normal things and couldn't understand why I couldn't make my normal DRBD config work. So if you have WFConnection problems and have tried the normal "mailing list" fixes, check your firewall status first!
Both Nodes Say the Following:
version: 8.3.8 (api:88/prot........
/usr/local/cpanel/bin/swapip domain(s)
It simply doesn't work, the Apache VHOSTS remain 100% unchanged, why does this script exist? I'm sure it would work from the control panel but I am locked out because my IP was changed and it doesn't match the CPanel license. I wish CPanel would make it easier to update the license IP.
I even took it a step farther, I manually edited the vhosts and restarted Apache and it........
Always make a backup of the original file before trying this, I find this kind of thing when updating IPs etc.. to use a script.
Where the old IP is "192.168.5.8" and the new IP is "10.10.5.8"
sed -i s/192.168.5.8/10.10.5.8/g testdomain.org.db
The -i with sed means "inline" meaning we edit the file directly, but without the -i we could just use >and output the results to another file or do whatever else we wanted.........
Create New RAID 1 Array:
First setup your partitions (make sure they are exactly the same size)
In my example I have sda3 and sdb3 which are 500GB in size.
mdadm --create /dev/md2 --level=1 --raid-devices=2 /dev/sda3 /dev/sdb3
mdadm: array /dev/md2 started.
Check Status Of The Array
*Note I already have other arrays md0 and md1.
You can see below that md2 is syn........
You'll see the following and the boot process will freeze:
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
I have struggled with this issue on vari........
I am a huge fan of Linux and the idea of OpenSource but I've said it many times, there are still hurdles in today in 2010 for Linux as a Desktop. Linux is still intended for servers at its very core. This can be changed succesfully though, as Apple has shown us with Mac OS X based on FreeBSD.
Half of the issue is lack of driver support and the other half is the Linux Kernel and Window Manages, KDE and GNome still both don't cut it (but they're getting closer).
I'll........
This error is annoying, in a Virtuozzo KB entry about this ip tables nat problem they say the kernel needs to be ugpraded:
Symptoms
The node runs 2.6.18-x kernel older than 2.6.18-028stab053.10.
NAT module does not work in container, you get "can't initialize iptables table 'nat'" error:
# iptables -t nat........
[27969.398749] sd 5:0:0:0: [sdb] 3907029168 512-byte hardware sectors (2000399 MB)
[27969.398749] sd 5:0:0:0: [sdb] Write Protect is off
[27969.398749] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[27969.398749] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[27972.117543] ata6.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0
[27972.117543] ata6.00: irq_stat 0x48000000
[27972.117543] ata6.00: cmd 60/08:00:ff:7........
If you have the "(auto-read-only)" beside an arrayI have no idea why that happens but it is easy to fix.
Just run "mdadm --readwrite /dev/md1" (rename md0 to the device with the problem and it will begin to resync.
md1 : active (auto-read-only) raid1 sdb2[0] sda2[1]
19534976 blocks [2/2] [UU]
resync=PENDING
........
I finally decided to look into some utils that did this, and the first one I found is "mp3burn". It is unbelievable simple and perfect. *2017-11 update and mp3burn is still available in standard repos such as Ubuntu 14/16 so this is a current and working project.
Just install the package and it gets all required libraries to convert and then burn's on the fly. And you won't believe how simple it is.
I just want to a directory that had the MP3's I wanted t........
This is obviously a bug in the r8169 kernel module and it seems to affect a lot of people. I upgraded to the latest kernel and hope this won't happen anymore, as it is a very serious error. This is especially serious for those who are running servers with this chipset, who can afford for the NIC to randomly go off-line for no apparent reason?
[655548.189113] type=1505 audit(1277067560.902:5): operation="profile_load" name="/usr/bin/freshclam&q........
http://www.tomshardware.com/news/RAID-5-Doomed-2009,6525.html
I found this article interesting, it basically says that with 2TB hard drives or larger sizes, you are more likely to encounter an unrecoverable read error. But is this just another Y2K doomsday? Don't HDD's have enough advanced hardware ECC error and read recovery to prevent this from happening?
I'm almost tempted to build a 3 x........
*Note OS X is strange to install, I thought my HDD was not being detected by you just have to go to Diskutil and create a partition for the root filesystem and then close/move the Window and proceed with the install.
After install Mac OS X 10.4.6 Tiger I get a black screen that says:
b0 error
Most people say the partition has to be marked as "active", actually that just means marked as "bootable". Instead of t........
My XBOX's dashboard/firmware was from sometime in 2008 when I first bought the system. I mainly played using composite cables but at my brother in law's house we used HDMI. The very first time it worked, but then I bought some games that did some update and after that HDMI never worked.
The symptoms besides having on sound is that your XBOX will show PC monitor resolutions but won't have any option to say you have a 720P or 1080P display, this means the XBOX firmware is fa........
Warning: get_browser(): browscap ini directive not set.
Solution is to edit /etc/php.ini
Uncomment this:
[browscap]
browscap = extra/browscap.ini........
Edit /etc/wwwacct.conf
Then add/edit the HOST line to add your hostname. eg:
HOST yourcpanelserver.com........
Basically the two main types of distros are Debian and RHEL/Centos based. I'm just going to give a quick overview of how the configuration of IP interfaces works in Debian/Centos based distros.
*Just one thing to remember, when setting IPs statically you have to manually specify a DNS server in /etc/resolv.conf (since DHCP is what normally does it automatically)
Debian/Ubuntu/Kubuntu/MEPIS
The IP (DHCP &........
One note is to secure MySQL, I don't know for sure but I believe you could login to MySQL remotely with no password during this operation (I'm not sure, maybe it doesn't accept blank passwords but I firewall MySQL port anyway and recommend you do the same).
First edit /etc/my.cf
Under the [mysqld] field add the following line somewhere:
skip-grant-tables
Now restart mysql: service mysql restart or on Debian sty........
www.antec.outervision.com/index.jsp
I found that wattage/power consumption tool to be very useful, especially when you're worried that you're hitting the Power Supply's limit. You'll see very quickly that different CPU's, Graphics, Cards, HDDS use a wide range of energy. That tool can help you choose a build that won't stress or go over the maximum limits of your Power Supply.........
I installed 5.5 with a 300GB RAID 1 partition (boot is also on this partition). It booted up fine the first few times until after I used a Live CD and accessed the array, and it became named /dev/md127 for some reason.
Now whenI boot into CentOS I get a kernel panic and different errors, once I got "invalid superblock", even though the array is fine (it didn't happen again, probably because I was sure to dismount and stop the mdadm array properly).
Here's what........
I'm not impressed with this motherboard, I was impressed with my Gigabyte AM3 board which seems to work flawlessly.
Everyone knows that the firmware is flawed, even though I have the F6, it still seems that the system doesn't reset properly or quickly enough.
Another HUGE problem is that in most Linux kernels the NIC won't work (if you try 10 times by rebooting it might). I also notice that you need to power down for it to work.
This board does not seem very com........
It always worked fine before but no amount of power unplugging/cycling does any good. I can access one network share and that is one that I've already saved, but it can't see any workgroups.
One silly thing is why is there no option to manually connect to a netbios name or IP?
It seems there is a bug with the firmware and that the SMB client is not working properly. Hopefully it fixes itself at some point.
Between this and the lack of support for embedded s........
cat /proc/user_beancounters produces the following:
kmemsize 1861537 5139870 12752512 12752512 26965041
Notice the failcnt "26965041", that is for kmemsize and at first it confused me. The system had enough guaranteed and enough burst RAM available. kmemsize is a variable indepedent of that, but who cars about the explanation right, let's just make thing........
I took an educated guess because it kept happening at the same spot when loading the XP install. I thought it was the hard drive or motherboard.
But it turns out my heavily used but loved NEC 3500 DVD-RW drive was the culprit. After disconnecting it and swapping it for another much beloved Pioneer DVD-RW, everything has gone smoothly.
I never ran into this or many issues because I've hardly used this drive since moving it to another Desktop years ago. I actua........
I'm not a fan of Asus and won't be buying another because of having to fight Asus over a bogus warranty denial (it's a long story but they only replied about how to RMA my unit weeks later on the EXACT day the warranty expired).
Anyway, it's just a matter of hitting F9 to do this, there's no need to worry about booting from USB or CD (unless of course you want a different OS eg. Windows XP Pro, Vista/7, or a flavor of Linux or Unix). Also remember that you need to fully/properl........
mdadm --assemble --scan
mdadm: /dev/md/diaghost05102010:2 has been started with 2 drives.
mdadm: /dev/md/diaghost05102010:1 has been started with 2 drives.
mdadm: /dev/md/diaghost05102010:0 has been started with 2 drives.
-bash-3.1# cat /proc/mdstat
Personalities : [linear] [raid0] [raid1] [raid6] [raid5] [raid4] [multipath]
md125 : active raid1 sda1[0] sdb1[1]
14658185 blocks super 1.2........
Out of memory: kill process 7559 (rsync) score 635 or a child
Killed process 7559 (rsync)
I was surprised to see this in my dmesg whenmy rsync backup suddenly stalled/stopped.
This system has 3 gigs of RAM and lots of free memory so I don't understand what is happening.
rsync invoked oom-killer: gfp_mask=0x200d2, order=0, oomkilladj=0
Pid: 7600, comm: rsync Not tainted 2.6.24.2 #83
[] oom_kill_pr........
I'm guessing RAM manufacturers forgot they're not the oil/gas companies and are playing games. It was just a year ago when I was buying 2GB sticks as low as $20 CAD! Now the average price is $50 CAD.
What happened to Moore's law when it comes to pricing for RAM? Every other piece of hardware generally has been coming down without exception.
........
ERROR: sdb2/backup.r18 failed verification -- update retained.
This happened when Iwas rsyncing a dying hard drive, a lot of people seem to report this as an error with rsync itself but I don't think rsync is the issue at all.
I know the source hard drive was bad, it was having all kinds of timeout, seek, hardware ECC recovered and reset errors.
The only time something else could be the problem is if the data is being corrupted in transit, perhaps through........
This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART.
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.11
Device........
Seagate Inventory/Firmware Check
I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate.
*Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate!
Seagate Inventory/Firm........
From the package "parted" you can use the command "partprobe" to re-read the partition table. I really hate rebooting, and that's what Iloved to hear about AHCI motherboards, that they allow hotswap so you don't have to reboot. But that's only as good as the OS, if the OS does not reload the partition table you won't be able to do anything with that new drive you attached without rebooting. Yes, even without re-reading the partiton table Linux will........
You can find it for free at http://nginx.org/ I find nginx is simpler to setup than pound (it's not hard but I found it unintuitive and annoying), it seemed to make some basic setups overly complicated with the config file syntax.
nginx on the other hand is perfectly suited in everyway, it is even simpler to setup and seems to be the most stable and most efficient any load balancer. I would go as far as to say that a good nginx setup is more relia........
Before we start I take no responsibility for this, you should have a backup and if you make a mistake during this process you could wipe out all of your data. So backup somewhere else before starting this as a precaution, or make sure it's data you could afford to lose.
The RAID 1 Setup (Hardware Wise)
I've already setup my 2 x 1TB (Seagate) drives with identical partitions, make sure your new hard drive (the empty one) is setup like your curr........
The binary "iostat" comes from the package "sysstat" and is available on all Linux/Unix like platforms.
Use the "-m" option to give you what you probably want, which is to see in MB/s how much bandwidth each disk is doing.
iostat -m
Linux 2.6.24.2 ((none)) 04/16/10
avg-cpu: %user %nice %system %iowait %steal %idle
........
I have no idea why but mkfs.ext3 defaults to a patheticlly small blocksize of 1024 bytes/1KB (kilobyte). That means the maximum filesize is ONLY 16GB! With 2KB/2048 bytes you get a 256 GB maximum filesize, and with 4KB/4096 bytes you get 2TB!
I finally noticed/paid attention to this after realizing that with rsync and scp that no file larger than 17GB could be transferred. I then realized it must be a file size limit on the partition.
Here is what tune2fs tol........
It's basically free bash shell script available from: http://wpkg.org/email2fax/index.php/Main_Page
Make sure you have the required tools:
libtiff
ghostscript
mpack/munpack
Where you can e-mail your Asterisk box and it will fax it to the phone number in the subject line. The good news ends there, it is fairly undocumented and buggy.
Take for example how the documentation mentions you can invoke from the com........
The folder I was trying to archive is about 72GB, but much like rsync at about 17GB it chokes because of the filesize. What's with so many common and essential Linux tools having such limitations? I guess it is likely that the authors never wrote their code with the idea that files would be so large but it's still very annoying. It's important to stay on top of these limitations on production servers because I didn't realize what happened until I checked the file with "........
The last transfer I was able to do was 16.77GB according to rsync's output and it worked fine.
16.77G 100% 10.66MB/s 0:25:00 (xfer#17484, to-check=234753/256249)
But on a file over 17GB (gigs) it stalls. Trust me, it really is stalled, it's been about 8 hours with no progression from that point for some reason.
17.24G 54% 10.65MB/s 0:22:07........
I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find.
yum search ftp
Loaded plugins: fastestmirror
Loading mirror speeds from cached hostfile
* rpmforge: ftp-stud.fht-esslingen.de
* base: mirrors.netdna.com
* updates: updates.interworx.info
* addons: yum.singlehop.com
* extras: mirrors.netdna.com
rpmforge........
Proxmox has made this free utility to backup running OpenVZ containers. It's a great program which is actually just a PERL script but gets the job done. This program is not 100% required because all it really does is cp -a from your container's path as far as I know but it is still good to have uniformity to how you backup your containers.
For RPM distros such as Centos/RHEL/Fedora etc.. download and install this:
wget http://www.proxmox.com/cms_proxm........
Here are the results, it is Sempron 3000+ AMD Mobile, 500Gig HDD, 512MB RAM with shared ATI Radeon graphics.
# # # # # # # ##### ###### # # #### # #
# # ## # # # #&nb........
PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist:
[code:1:1fd0f3abbe]
if (!file_exists($OPENSSL)) {
//echo "ERROR: OPENSSL $OPENSSL not foundn";
}[/code:1:1fd0f3abbe]
I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........
CentOS (most Linux) no-RAID to software RAID-1 guidehttp://lists.centos.org/pipermail/centos/2006-January/018624.html........
Nice General Linux RAID 1 GuideFull examples/tutorials that should work for any Linux system using GRUB or LILO as the boot loader.
This is the only tutorial I've seen that clearly shows how you can convert an existing non-RAID system to software RAID1 remotely, without ever having to be at the computer. This is important for people who co-locate or rent dedicated servers that they may not have physical access to in a timely manner.
https://alioth.debia........
Heredoc warningsExample
$somevariable = ........
Centos 4.3 x64 & VMWare Server Beta[code:1:6d0b2c8c2f]
The correct version of one or more libraries needed to run VMware Server may be
missing. This is the output of ldd /usr/bin/vmware:
linux-gate.so.1 => (0xffffe000)
libm.so.6 => /lib/tls/libm.so.6 (0xf7fbd000)
libdl.so.2 => /lib/libdl.so.2 (0xf7fb9000)
libpthread.so.0 => /lib/tls/libpthread.so.0 (0xf7fa7000)
libX11.so.6 => not f........
Upgrade Release Kernel TipsThis is for CentOS 3.1 to 3.8 but the methodology will apply everywhere.
I ran into a problem first of all with a non-booting system after running
#yum update centos-release
It took me to 3.8 and upgraded all the other packages [b:7e931c835d]BUT[/b:7e931c835d]
because of some stupid flags enabled in /etc/yum.conf the KERNEL WASN'T UPGRADED SO AFTER BOOTING, WELL IT DIDN'T BOOT OF COURSE :)
H........
Setup Static IP Address ONBOOTAssuming you are using eth0
Note this will work for any version of CentOS and basically any version of Redhat Linux or Redhat based distribution.
You would need to create a new file
[code:1:02f8d34c30] /etc/sysconfig/network-scripts/ifcfg-eth0:0[/code:1:02f8d34c30]
DEVICE=eth0:0
the ":0" at the end specifies alias 0 we could actually change this to ":99" or "........
Updated to Version 3.8 and can't loginSSHD accepts my password but then hangs at "Last login: Wed Sep 13 21:30:02 2006 from"
This occurred during a yum update after upgrading my release, installing the new kernel and rebooting.
I got kicked out of sshd after seeing the following during yum update:
telnet 100 % done 85/476
tux 100 % done 86/476
ntsysv 100 % done 87/476
rpmdb-redhat 94 % done 88/476........
Telus + 2Wire 2700 Router HorribleWell first of all let me say this is the only router/switch that sometimes seems to crash/disconnect computers on the local network.
This device also thought it would be smart to block VOIP packets coming from my Sipura ATA VOIP adapters so I disabled the [quote:cb89ba7bff]"Invalid TCP Flag Attacks (NULL/XMAS/Other)"[/quote:cb89ba7bff] option
Then all of a sudden I couldn't get onto any web pages, the wireless........
DVD Burners and Media at an all time lowThis is crazy you can buy a nice Pioneer DVD burner for like $64 CAD now and good media like 50PC Maxell is just $25.97 at Walmart.
I'm liking this. Time to make double archives of important data :)........
E-Mail TipI just thought I'd give you guys a good tip about e-mail. It seems a lot of people like to use a Hotmail or ISP (eg. Telus) account for their e-mail but the problem is what happens if you switch ISPs, then your e-mail address no longer works and old friends might not be able to contact you. The same thing has happened for excite.com e-mail addresses where they just shut down.
Whether you are a business owner or personal user can you afford to lose an e-mail........
The New Chips on the BlockThe New Chips on the Block
By Bruce Gain
Story location: http://www.wired.com/news/infostructure/0,1377,67795,00.html
02:00 AM Jun. 13, 2005 PT
We have embarked upon a new era in x86 PC computing -- so say chip giants AMD and Intel following their launches of dual-core PC processors. So how will dual-core processing change your PC computing experience? Our FAQ should help you decide whether or when you sho........
Become your own ISP!http://waverider.com/
I would link to the exact product I am mentioning but it's under Products/5.8Ghz because I can't find the exact URL because of their annoying javascript and frames (you'll see what I mean).
The exciting thing is that this unit can supposedly be up to 72mbit, it is NOT line of sight and the range is up to 20miles. I wonder how real world speeds and range would actually be and if it is reliable.
I j........
Trouble connecting between Windows XP and Windows 98 SharesOk a few things to check for:
* Disable all firewalls
* Make sure NetBEUI is enabled on both computers
* Make sure the Windows XP computer has the name of the computer logged in user of Windows 98 added as an XP user
* Add the XP user to anything you want to share
That fixed my problem........
PHPBB Drop All TablesSQL Syntax:
[quote:75acd496c1]drop table phpbb_auth_access, phpbb_banlist, phpbb_categories, phpbb_config, phpbb_confirm, phpbb_disallow, phpbb_forum_prune, phpbb_forums, phpbb_groups, phpbb_posts, phpbb_posts_text, phpbb_privmsgs, phpbb_privmsgs_text, phpbb_ranks, phpbb_search_results, phpbb_search_wordlist, phpbb_search_wordmatch, phpbb_sessions, phpbb_smilies, phpbb_themes, phpbb_themes_name, phpbb_topics, phpbb_topics_watch, phpbb_user_group, p........
Helpful IPFW ExamplesSomeone's real life examples:
http://lists.freebsd.org/pipermail/freebsd-security/2004-July/002181.html
Or you can try the FreeBSD Handbook guide:
http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/firewalls-ipfw.html........
Proftp Passive PortsIf you use a locked down firewall you can edit proftpd.conf and tell it something like this:
[quote:8419cab1f8]PassivePorts 6170 6270[/quote:8419cab1f8]
That would force all passive ftp traffic to ports 6170 6270 which you could then open on your firewall rather than leaving open ports 1024-65000 open........
Create Table with structure of another existing tableOk, this has many valid uses such as if you need to create backups or the ability to undo changes, you would want to create new tables with the same structure as another. Here is how you do it.
[i:7ed9581493]
Also remember Indexes such as PRIMARY KEYS [b:7ed9581493]will not be preserved[/b:7ed9581493] so you will have to readd them manually.[/i:7ed9581493]
[code:1:7ed9581493]CREATE TABLE NewName AS SEL........
CVSUp the Easy WayIf you're reading this you probably have never used CVSUp or don't know how.
CVSUp can be used for two things or just one if you prefer.
*Keeping your kernel up to date
*Keeping your port list up to date
Start by editing the following file in:
[b:76928b387d]vi /usr/share/examples/cvsup/cvs-upfile[/b:76928b387d]
It can be quite overwhelming with all the crazy options.
Basically there are only 3........
Windows Media PlayerJust one little question... and I'm not too sure if it falls into the hardware category... my Windows Media Player...or any music program for that matter buzzes at random and cuts out the music. But I don't think it's the music files themselves because I've put in regular CD's and have had the same problems. Any ideas on what the problem could be?Sounds like a soundcard/driver issue.
I would recommend updating your soundcard driver i........
Norton Antivirus is the worst - who would have known?http://www.software-antivirus.com/
Check the link above, that review site lists Norton as one of the ones to stay away from. With good reason too, I always wondered why Norton seemed to miss so many viruses, spyware and such. Even when it didn't, it was absolutely useless because it was either unable to delete the file and it was never able to repair or disinfect.
So in essence, from my experience, N........
ECS K7S5A Motherboard System Take Up To 2 Minutes To BootHi guys,
My motherboard is very strange. Sometimes it will take up to a few minutes to post. I have no idea it suddenly started doing this. I have tried everything and all I can figure is that it is somehow related to the USB ports possibly.
Why do I say this?
Because if I disconnect my scanner the problem occurs less frequently. I only have a printer hooked up to USB now and by........
NEC ND-3500A is great!I just picked up an NEC 3500A a few weeks ago and I love it.
It is a great all in-one optical drive solution.
It can burn DVD/+R-R at up 16x, read at 16x and rewrite at 4x and CD-R at up to 48x!
Not bad, but the impotant part is that it delivers consistent high quality burns and the drive is as quiet as I could ask it to be.
It's also convenient that it has a lot of hacked firmware for overspeeding of........
Basic Port ListingHopefully someone finds this useful or at least interesting.
http://www.sans.org/top20/#u9
Name Port Protocol Description
Small services ........
My list of handy security links - Ongoing[b:6f8d25be68][size=18:6f8d25be68]News[/size:6f8d25be68][/b:6f8d25be68]
Security Focus http://www.securityfocus.net - Nice Security News Site
CERT http://www.cert.org/
Common Criteria (see if your OS/software is EAL4 certified) EAL(Evaluation Assurance Levels is the industry standard for evaluation of security in software) http://www.commoncriteria.com
[size=18:6f8d25be68][b:6f8d25be68]Tools[........
Other Security Web SitesSeveral websites actively track security issues. This list provides you with the major providers
of security information on the Web. Many of these organizations also provide newsletters and
mailings to announce changes or security threats:
Center for Education and Research in Information Assurance and Security (CERIAS)
CERIAS is an industry-sponsored center at Purdue University that is focused on technology and
relate........
Nice Search Engine Optimization Toolshttp://searchenginewatch.com/facts/article.php/2156041
I quickly checked this out and I like the Google tool that helps you determine the popularity of certain keywords and then it gives you other related search terms that those people used to search with.
Excellent :)........
I played around with xmit power (how much power in mW) to see if I could increase the range and signal strength. Idon't think this Linksys WRT54G's strength is the wireless, it seems to have poor signal quality and transfer rates all around.
Ithink part of the problem is also that there are several wireless networks around my house that could be interfering and the walls are thick here.
Anyaway, moving on now :) The default is 28mW and I increased it to........
gnuCash is available for all main platforms, Linux/Unix, MacOS (FreeBSD anyway), and Windows.
You can download gnuCash free from here.
It does seem to be fairly full featured and somewhat straight forward, but like so many programs it is missing a few key features or things don't work quite right.
It doesn't support importation of CSV files, which is a big minus. And the developers rather than wanting to add support have just dec........
*This is a bug with initramfs support, all kernels after around 2.6.27.54 suffer from this problem.
If you try to include initramfs into your kernel (I mean actually building your binaries into the kernel) this will always happen. Obviously some code has changed in recent kernels that is present in all new kernels, it makes it impossible to boot
I've tried the latest 2.6.32, 2.6.33, 2.6.34, 2.6.35, 2.6.36, 2.6.37, 2.6.38 kernels and they all do this. I found one bug re........
This is a very weird, annoying and bizarre quirk with many distributions, especially Debian. The home and end keys don't work, but it's a simple fix as long as you found this article :)
You just have to edit /etc/inputrc:
Find the commented lines as shown below:
# "e[1~": beginning-of-line
# "e[4~": end-of-line
*If you can't find the above, just copy and paste the code below into your inputrc, it will en........
Put what you see below into your .htaccessand it will enable errors and notices. (change on to off and 1 to 0 to disable though)
php_flag display_startup_errors on
php_flag display_errors on
php_flag html_errors on
Now you'll be able to see errors and notices but this should really only be used for debugging purposes and only temporarily as it can be a security issue since errors can reveal information you wouldn't want hacker........
This happened with a select statement which writes the result to an external file. I didn't remember the privilege "FILE" must be granted on *.* for this to work successfully, it wasn't actually an authentication issue as it implies since I was already in the SQL prompt and doing the query.
SELECT some_id
FROM sometable
INTO OUTFILE '/tmp/result.txt'........
top - 09:34:12 up 2 days, 20:57, 2 users, load average: 1.83, 1.99, 2.03
Tasks: 59 total, 2 running, 57 sleeping, 0 stopped, 0 zombie
Cpu(s): 0.3%us, 0.0%sy, 0.0%ni, 0.0%id, 99.7%wa, 0.0%hi, 0.0%si, 0.0%st
That 99.7% wa is iowait, it means the server is waiting for a process to complete an IOoperation or in plain English, there is a delay in........
I bought a Dynatron A46G for my AMD X4 620 AM3 Quad Core CPU. Just judging by touch, the stock OEM fan/heatsink combo kept things so cool, I could leave the 1U server on the floor and it barely felt warm to the touch, including the heatsink itself.
I thought the Dynatron A46G would be enough with passive cooling (it has no fan), but the same setup became burning hot on the underside of the server and also by touching the heatsink itself within minutes.
I thought that th........
I was starting to panic because suddenly my 1TB Seagate SATA drive wasn't working,I thought it was a BIOS issue because it seemed to have happened after I tried overclocking my Desktop too much.
I tried powering down and waiting, but I still couldn't hear the drive spin up at all. I tried a second 1TB hard drive and it wouldn't work either. I checked all power connections again and again until one of the pins in the MOLEX connector popped completely loose.
Th........
I've tried to find a good sensible solution to cluster with and each technology has it's pros and cons and there is no perfect solution and I've found a lot of "exaggerations" in the applications, benefits and performance of these different filesystems.
DRBD
I first started off with DRBD and Ihave to say it does live up to the hype, is quite reliable (although it can be annoying to match up the kernel module and user applications since they must match and whe........
Itried everything Icould think of, and of course even with the NIC enabled in the BIOS nothing was working. The light would flash when you plugin the cable for a second, but that's all.
Due to another issue I'm about to post about (server is not compatible with 1TB/1000Gig Hard Drives), I updated the BIOS. I didn't even know the 100mbit NICs were not working untilI decided I should test each NIC one by one.
Inoticed that only 1 server out of........
In those 4 simple commands you can setup mutual key exchange between two sshservers by using a single login shell session and single window.
*Just change the IP address examples of (10.10.0.2) to the target of your mutual key exchange. It doesn't matter if the server is on a LANor WAN(well unless the server is behind a firewall and you cannot SSHinto it).........
In Newer Linux Distros This Way Is Easiest and works on newer versions like Ubuntu, Mint, Fedora, Centos, Debian etc.
#if you are missing timedatectl this in newer distros like Ubuntu/Mint/Debian and are using a container like Docker then do "apt install systemd"
timedatectl set-timezone America/Vancouver
Replace the America/Vancouver with the correct timezone.
To see the list you can just type "timedatectl set........
A VPS Server I had just wasn't working right, code that I migrated there just wasn't working. For example, it kept telling me the connection to the database was unsuccessful, halfway through iterating through results it already had.
Then I realized it wasn't my code. Ichecked my /proc/user_beancounters and found this:
cat /proc/user_beancounters
Version: 2.5
uid resource held maxheld barrier limit failcnt........
This is something that annoys a lot of people, fortunately the Redhat style OS's are the most simple in this respect. I disagree that Debian's way makes sense, it is more of a hackish approach in how they implement iptables.
Anyway, for those who are using Redhat/Centos style OS's it is very simple.
Set your rules from the shell/command prompt and to save the iptables firewall rules so they are remember/loaded on boot just run this command:
service iptables........
There have been lots of reports like this going around and Ican confirm my 3GS with 3.0 firmware is overheating as well. It gets quite hot and actually can make your head or hand sweaty when holding it to talk, or simply holding the back cover for any reason.
It's a wonder how the device cools itself at all, considering the only thing that could ventilate air are the 2 speakers at the bottom or the single speaker on the front of the device.
Apple seems to be making........
This is pretty bad, ever since my phone has been unlocked the battery life is horrible. Many others have reported this issue on provider unlocked phones and even jail broken phones. We're talking issues as bad as losing 1% every 3 minutes which is what I seem to have observed as well.
For now I'm going to relock the phone, and hopefully a firmware update will address this issue. This is very annoying and it seems apparent this is also happening on 3G phones and that........
First of all, the iPhone is crippled in many ways, but most of my complaints about functionality have been addressed through the jailbreak, Ican run apps in the background of my choosing, I can install a terminal, acccess my phone through SSH and SCP and so much more.
It even addresses the 15 minute e-mail problem, I installed a program called "PushMod" and now set the checking time to just 1 minute.
Apple should really thank the developers for this gift, it ma........
Everything was working fine but I believe when Iturned off "EDGE" in Big Boss everythign went haywire, at first my WiFi dropped, then 3G didn't work and I couldn't even make phone calls.
If you're having this trouble with your jailbroken 3GS running 3.0 firmware, make sure you don't turn off EDGE, it seems to disrupt all service to your phone.........
First of all you need to be jailbroken, but this is not covered here.
Go into Cydia and click "Manage Sources" then "Edit"and add: repo666.ultrasn0w.com
Then search for "ultrasn0w" as a package and install it, that's all there is to it, your iPhone is finally unlocked so when you travel abroad you can avoid ridiculous roaming charges, or you can switch providers and use any SIMcard you like.
You'd really thi........
Apple crippled the iPhone by not allowing multi-tasking of the non-primary apps. I use SSH a lot and I don't want to close my session just to check my e-mail, etc, now an app found in Cydia called "Backgrounder" allows just that.
Although it's not perfect, we installed the correct one for "3.x" iPhones and hit "Reload SpringBoard" and the hour/circle glass has just been going for minutes.
It seems like it installed fine even with the crash t........
This happened during a sync of my iPhone while installing some apps. This usually happens to non-jailbroken iPhones who are trying to install non-Apple approved software OR jailbroken phones who haven't done the "Sync update".
How to fix this error and get the Sync Update
Open Cydia - Manage - Sources - Edit
Add this source: http://cydia.hackulo.us
Then under the section "Hackulo.us" install "Ap........
Truly, the only way to unleash the capabilities and customization abilities of iPhone are to jailbreak, it's not just for hackers anymore.
A few days ago someone by the named of "geohot" released a single click application called "purplera1n", which does the entire operation smoothly and seamlessly.
In our case, the first time it went as far as "done, wait for reboot" on our Windows machine and for minutes we waited and saw the pic on the iPhone w........
Yes, Iadmit I finally got bitten by the hype as much as I can usually see through it all. Keep in mind this review is of the "stock" phone, no jailbreaking yet which is what really unleashes the customizability and whyI bought iPhone.
I had better things to say about this phone before buying it, and it is a great phone, perhaps the best on the market by far, if not because of the Mac OS port onto the iPhone and all the apps, etc, etc.
With that said........
I kind of expected this feature to be there in some form, to stay ahead of the pack Apple needs to stay on top of this. User's of HTC's Android smart phone which uses a Linux based OS with Google's power behind it, note that you can save passwords in the browser on that phone.
Apple needs to continuously evaluate the needs in its core apps and make sure the features are cutting edge and top notch, if other phones come out with some of these seemingly small but essential features........
The dmg format is silly and annoying to work with, why couldn't Apple stick with the .iso standard? Anyway, there's an excellent Linux and Windows based tool to convert it back to a normal .iso Image called dmg2iso
I'll only cover theLinux version although the Windows pre-built binary works the same way.
Download dmg2iso here for free (from the author's website)
It's just silly and doesn't make sense that Ubuntu doe........
As much of a computer nerd as Iam, I'm usually a late adopter to technology for a few reasons. Ifeel most new hyped technologies and electronics are mainly fads, and I'm also cheap.
Adopting later means you avoid the bugs, kinks and most importantly pay the lowest price, that's me being cheap again :)
I never read much about the iPhone but Isaw all the hype around it and until recently I wasn't a big fan of anything Apple until a few years ago I realize........
I've had an old Blackberry for a few years and I was ready to spend some serious cash on a nice Nokia. I love the idea of the Linux based Symbian S60 OS, so I was looking at phones like the E63, E71 (both are basically the same, at least CPU/screensize although E71 is thinner, has a 3MP camera, has GPS, and has dedicated buttons to adjust the volume).
Then Iheard about the N97 and what a revolution it was supposed to be and it was even compared to iPhone.
To........
This is the Intel Atom 330 motherboard with integrated Realtek Gigabit NIC (Intel Desktop Board D945GCLF2 Motherboard W/ Atom 330 1.6 GHz Dual Core Processor - Mini-ITX)
I cannot achieve more than 15 MB/s, even doing a local transfer through eth0 to it's own IP.
100% 95MB 15.9MB/s 00:06
So this is not a cabling, switch or hardware issue, it seems like a driver or chipset limitation problem.
Here is my........
resume: could not stat the resume device file
I got that after migrating to a different physical hard drive, it wanted to resume from a swap partition that no longer exists.
This is actually controlled by "uswsusp.conf" in /etc
Just edit it and remove the device or change it to the correct new swap file.........
Igot this after copying a VMWare image onto another machine in Debian.
SIOCSIFADDR No such device eth0 error while getting interface flags
The solution
1.) Find and edit the device line in persisent-net.rules note it will be prefixed with something like z25 or something else.
vi /etc/udev/rules.d/z25_persistent-net.rules
The easiest way is to comment anything out.
If you are feeling........
When trying to even cd or ls the mounted OCFS2 partition it crashes. Ithink this is a combination of VMWare Server's problem and the way I mounted and symlinked to it.
More than anything this shows the problem and lack of forsight with VMWare, but also that OCFS2 is easily crashed if you do strange things.
Output of /var/log/messages for OCFS2
Apr 10 15:57:45 localhost kernel: [84331.691258] Modules linked in: vmnet vmci vmmon ocfs2_stac........
I've read a lot of people complaining that their 1U servers are too loud for the office, home or whatever strange places people might want to put them.
Whenever Isee the question asked, "what can be done about the noise", you'll see a myriad of silly answers like "you shouldn't have it at home or in your office at all", "1U servers are meant to be loud".
These all might be valid points but they're not the solution. A good example is a........
Ithink there has been a lot of negative press towards Rackable Systems. We will give their new solution credit that it is marketed very well, and comes prepackaged and ready to go.
But let's cut through the hype of both sides, the people who love this concept and the people who hate it.
What Rackable Systems have done is a first, to minimize space, power and costs into small servers. This is great, and many companies have already built their own servers based........
This happened on one of my Ubuntu machines where Igot some kind of segfault on line 21 from LAME at random while encoding MP3s (a second try is fine usually). I've read that it's best to compile it from source and that has solved most issues for people.
Here is my preferred configure line:
./configure --enable-mp3x --with-fileio=lame --enable-debug --with-vorbis
Even with that I got a different error this tim........
There's a lot of outdated information and confusion for system administrator's out there.
One annoying task for many an Administrator has been backing up data in Linux. You don't need any GUI tools such as K3B or GnomeBaker. Both are excellent tools but for veteran command line users working remotely, using the keyboard is a great and possibly automated way to save yourself pain and hassle.
At a later date we'll cover how scripting can automatically backup certain........
http://searchenginewatch.com/2165111
This was an interesting article and people should be wary of Google's power. Google's policies and actions against competitors borders on anti-trust, far worse than Microsoft.
They are doing the right thing for all of us, Google says selling advertising and links is bad for search engines, yet they don't penalize sites who use AdSense.
........
We've noticed in many ways that traditional networking even in WANs and LANs has changed very little. Years ago most networks were running on 100mbit and today most still are.
Even the average internet connection is largely unchanged from several years ago with some minor exceptions from Europe and Asia.........