• Docker Container Onboot Policy - How to make sure a container is always running


    Generally most containers are by default set not to start automatically. Ther eare 3 settings for the "RestartPolicy" of containers: No: Do not automatically restart the container (default). Always: Always restart the container regardless of the exit status. Unless-stopped: Always restart the container unless it is explicitly stopped. On-failure:........

  • How to Install FreePBX 17 in Linux Debian Ubuntu Mint Guide


    FreePBX official install guide is here. Requirements: Debian 12 Download Link Minimal - System Utilities RAM: 4G HDD:20G Note that if you don't have the required base OS yo........

  • Linux and Windows Dual Boot Issue NIC Won't work After Booting Windows


    In Windows, with some NICs, especially Intel, Windows may enable features on the card that break it in Linux. It is hard to troubleshoot as what you'll see is that the NIC is still detected in Linux, the NIC/port will be up but nothing will work (eg. DHCP requests or even static IPs won't work). You may see STP bridge traffic but that is all. In a corporate environment this can result in many calls to support and is essentially downtime and an unnecessary waste of resource........

  • Cisco CME How To Enable ACD hunt groups


    In our example below, we create 2 hunt groups. You could assume the #1 group is sales and #2 group is support etc.. and you can create more as needed. The main part of hunt is the "list" option where you add each phone number that is to be part of the group ephone-hunt 1 sequential pilot 2001 list 1234 timeout 10 ephone-hunt 2 sequential pilot 2002 list 5678 tim........

  • How to install gns3 on Linux Ubuntu Mint


    Step 01 - Download Visit https://gns3.com/software/download Click on "Linux" on the side under "Installation".........

  • Cisco CME How To Configure SIP Trunk VOIP


    This is how we configure outside PSTNaccess or dialing through another SIPtrunk. Beware that this a simplistic example that neglects most security including SRTP First you'll need to be in config mode: Step - 1 Enter Voice Service VOIP security options There are more options but for now we'll just focus on security/allowing connections to and from our phones and the trunk. Router(config)#voice service voip ........

  • Cisco CME and C7200 Router Testing and Learning Environment on Ubuntu 20+ Setup Tutorial Guide


    Since newer versions of Ubuntu like 20, you will find there is no longer dynagen and that the dynamips provided is faulty and will segfault each time: Cisco Router Simulation Platform (version 0.2.14-amd64/Linux stable) Copyright (c) 2005-2011 Christophe Fillot. Build date: Apr 3 2018 12:20:29 Local UUID: 3c1c0b7f-2fab-4fda-b40b-74841d1bcfe0 Instance ID set to 1. netio_tap_create: unable to open TAP device tap1 (No such fi........

  • Abusive IP ranges blacklist


    Make sure this makes sense for you but I've started to block a lot of commercial Cloud services and easily accessible providers as they are a very high source of abusive traffic. The cost savings for a lot of organizations are huge, as you now have less bandwidth usage and less resource usage from garbage/bot/malicious traffic. This mainly works for when you can be reasonably sure that your audience has no business visiting your service(s) from freely accessible commercial IP ........

  • CDN Cloudflare how to set and preserve the real IP of the client without modifying application code on Apache


    Your frontend CDN (eg. Cloudflare or even your own load balancer/proxy) must be sending the X-Forwarded-For and you must be running Apache on the backend. This solves the problem where your logs and services will only see the proxy/CDN IP and not the real client IP. mod_rpaf will fix all of this This solution transparently sets the real IP of the client for Apache and any services that rely on........

  • CentOS 7 fix Could not retrieve mirrorlist http://mirrorlist.centos.org/?release=7&arch=x86_64&repo=os&infra=container error was 14: curl#6 -


    yum update Loaded plugins: fastestmirror, ovl Determining fastest mirrors Could not retrieve mirrorlist http://mirrorlist.centos.org/?release=7&arch=x86_64&repo=os&infra=container error was 14: curl#6 - "Could not resolve host: mirrorlist.centos.org; Unknown error" One of the configured repositories failed (Unknown), and yum doesn't have enough cached data to continue. At this point the onl........

  • How to set Linux Ubuntu Redhat Debian Command Line http https socks proxy for yum apt


    Just export these variables: export http_proxy="socks5://127.0.0.1:1234" export https_proxy="socks5://127.0.0.1:1234" The above example uses a socks 5 proxy at localhost and port 1234. This is a great way to improve performance of some activities for things like package installation, especially if your routing is not ideal to the repos.........

  • hostapd example configuration for high speed AC on 5GHz using WPA2


    This example is using RTL8821AU chipset from a TP-Link T2U Plus USB adapter and other similar ones should work the same. Here's how to get this chipset RTL8821AU working in Linux. Here's how to get RTL8812 and RTL8822 working in Linux.........

  • hostapd how to enable and use WPS to connect wireless devices like printers


    Edit your /etc/hostapd/hostapd.conf file like below and restart hostapd. #WPS stuff # Enable control interface for PBC/PIN entry wpa_psk_file=/etc/hostapd/hostapd.psk ctrl_interface=/var/run/hostapd eap_server=1 wps_state=2 ap_setup_locked=1 wps_pin_requests=/var/run/hostapd.pin-req config_methods=label display push_button keypad #WPS model info stuff change to suit your needs d........

  • Dell Server Workstation iDRAC Dead after Firmware Update Solution R720, R320, R730


    This is certainly a poor design, as you can read many seasoned admins who have updated their iDRAC only to have it killed. One possible cause is not by doing all the incremental updates, doing updates from an old iDRAC to one many revisions newer is a sure way to kill things, but even then there is no guarantee based on the amount of failures. List of threads of people's dead iDRAC's:........

  • Cloned VM/Server/Computer in Linux won't boot and goes to initramfs busybox Solution


    This is mainly for if you've done something silly like trying to clone a Live, running VM image. In this example, the VM initially finds grub and tries to boot but is kicked straight into initramfs rescue mode/busybox right after this. If you've done this "silly" thing, you could have dataloss but a lot of times just using fsck will fix it as you are guaranteed at best to have some corruption and inconsistencies in the filesystem. My theory is that some files wer........

  • Debian Ubuntu 10/11/12 Linux how to get tftpd-hpa server setup tutorial


    apt install tftpd-hpa #change TFTP_ADDRESS to by setting address to 192.168.1.1:69 or the IP you need, otherwise it will listen on all IPs and interfaces which could be a security risk. # edit /etc/default/tftpd-hpa TFTP_USERNAME="tftp" TFTP_DIRECTORY="/srv/tftp" TFTP_ADDRESS="192.168.1.1:69" TFTP_OPTIONS="--secure"........

  • efibootmgr: option requires an argument -- 'd' efibootmgr version 15 grub-install.real: error: efibootmgr failed to register the boot entry: Operation not permitted.


    This sometimes happens when trying to install the EFIversion of grub to a device when you are booted into Legacy/MBR mode. It doesn't seem to occur on all machines, but some and seems somewhat BIOS dependent. grub-install --target=x86_64-efi /dev/sda Installing for x86_64-efi platform. grub-install.real: warning: Couldn't find physical volume `(null)'. Some modules may be missing from core image.. grub-install.real: warning: Couldn't find physica........

  • Linux Debian Mint Ubuntu Bridge br0 gets random IP


    This can break things easily in remove environments where it was normally easy to convert a normal eth0 to a bridge under br0, and that bridge would normally have the same MAC address by default, which is desirable for most situations. In Debian 11 this is different for some reason now. https://unix.stackexchange.com/questions/681013/bridge-gets-random-mac-........

  • How to kill a docker swarm


    Assign way more replicas than you have of memory on all nodes and watch the Swarm crash which can easily reproduce in a small VMfor testing. root@Deb11Docker01:~# docker ps CONTAINER ID IMAGE COMMAND CREATED STATUS PORTS NAM........

  • nvidia cannot resume from sleep Comm: nvidia-sleep.sh Tainted: Linux Ubuntu Mint Debian


    This seems to happen in many different drivers but it happened more often in newer versions such as 530 vs 525. Then nvidia-modeset goes to 100% There are many reports of this appearing since driver 4.70 and I can confirm I've seen this in various machines. https://forums.de........

  • How to access a disk with bad superblock Linux Ubuntu Debian Redhat CentOS ext3 ext4


    Have you ever tried mounting a partition that you exists but you get this error? mount: /mnt: can't read superblock on /dev/sda1. The superblock in this example was bad because the physical disk had corruption and bad blocks/sectors. However, the data was generally accessible and you can always try this trick below (with caution and no warranty). This is specifically for filesystems that place superblocks in multiple locations, which........

  • How To Stop DNSMasq from listening on all IPs/Interfaces and allow only localhost


    Some people find it less than intuitive to do on DNSMasq and by default DNSMasq is available on 0.0.0.0 which could even be your LAN or Public IP. Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp ........

  • du - VAS Billing Subscriptions Hack/Scam MLPremiumSub Invascom Astromart Issues Complaint


    If you have du, you may want to check your bill, as you can read about a longstanding issue with fraudulent charges showing up and many users claiming they did not subscribe or solicit those offers. These don't normally show up on new accounts, but they seem to target established users and maybe even users they suspect are not watching their phone or bills, while they are on vacation. These charges can frighteningly happen with 0 interaction from the user despite what........

  • Docker Swarm vs Kubernetes Comparison Guide


    A lot of companies are unsure which solution to choose and many may not be aware of Docker Swarm as an alternative to Kubernetes. One thing that many Sysadmins find is that Docker Swarm is simply easier, quicker to setup and maintain by far than Kubernetes.........

  • When is it time to leave your VPS/VDS Cloud Hosting Provider?


    When Is It Time to Leave Your VPS, VDS, and Dedicated Server Provider? Choosing the right hosting solution—be it Virtu........

  • 2024 Buyer's Guide: How to Choose and Buy the Best VPS/VDS for Your Needs - Tips and Strategies


    In today’s digital landscape, finding a reliable and secure Virtual Private Server (VPS) or Virtual Dedicated Server (VDS) goes beyond just comparing specs and prices. With increasing concerns over data privacy, security breaches, and government surveillance, the wisdom of choosing your VPS/VDS provider based on juri........

  • Install Grafana on Linux Debian Ubuntu Tutorial Guide


    First we need a few extra packages: apt update apt install -y adduser libfontconfig1 musl sudo wget https://dl.grafana.com/enterprise/release/grafana-enterprise_10.3.1_amd64.deb Install / Enable Grafana dpkg -i grafana-enterprise_10.3.1_amd64.deb dpkg -i grafana-enterprise_10.3.1_amd64.deb (Reading database ... 44309 files and directories currently installed.) Preparin........

  • How To Upgrade Debian 8,9,10 to Debian 12 Bookworm


    Step 1.) Upgrade to Debian 11 first The process to go to Debian 12 is not as smooth as 11, when trying to upgrade from Debian 10. In fact, it doesn't work directly, so you'll first need to follow this guide to update to Debian 11, reboot and come back here if successful. Step 2.) Update sources.list Update your /etc/apt/sources.list like this: deb http://........

  • Linux dhcp dhclient Mint Redhat Ubuntu Debian How To Use Local Domain DNS Server Instead of ISPs


    If you are running a local DNS server like named/bind and don't want to use the ISPsupplied DNS servers that are announced via a DHCP request (using dhclient) then the solution is simple. The reason should be obvious, but normally running your own DNS server will provide a more reliable, and fast DNS response and you won't have to worry about filtering as much (unless your upstream filters or proxies outgoing DNS requests). Edit /etc/dhcp/dhclient.conf........

  • apache2 httpd apache server will not start [pid 22449:tid 139972160445760] AH00052: child pid 23248 exit signal Aborted (6) solution Mint Debian Ubuntu Redhat


    If you get this error, it is often because you have configured Apache with modules that weren't actually installed. Eg. you try to load the PHPmodule but didn't actually install the apache2 php module, so the server can't start. In general, this error can often be caused by issues with problematic modules and/or Apache being configured for modules that have not actually be installed (eg. libapache2-mod-php) is missing. The above results in this less than obv........

  • How To Setup Python3 in Ubuntu Docker Image for AI Deep Learning


    The issue is that Docker images are stripped down, so many tools and even python3 is missing, so you'll have to build or update the actual image yourself. I assume you have started an image with something like this and that you have the Nvidia Toolkit installed (assuming you are using GPUs). If you're not using nvidia just remove --runtime=nvidia --gpus all. docker run -it --runtime=nvidia --gpus all ubuntu bash These works for most images li........

  • How to Configure NVIDIA GPUs with Docker on Ubuntu: A Comprehensive Guide for AI Deep Learning CUDA Solution


    Welcome to our in-depth guide on configuring NVIDIA GPUs with Docker on Ubuntu. This post is tailored for developers, data scientists, and IT professionals who are looking to leverage the power of NVIDIA's GPU acceleration within Docker containers. Whether you're working on machine lea........

  • Linux Ubuntu Mint how to check nameservers when /etc/resolv.conf disabled solution


    You'll notice that /etc/resolv.conf contains dire warners on most Linux Desktops. # This file is managed by man:systemd-resolved(8). Do not edit. # # This is a dynamic resolv.conf file for connecting local clients to the # internal DNS stub resolver of systemd-resolved. This file lists all # configured search domains. # # Run "resolvectl status" to see details about the uplink DNS servers # currently in use........

  • Docker cannot work on other overlayfs filesystems such as ecryptfs won't start overlayfs: filesystem on '/home/docker/overlay2/check-overlayfs-support130645871/upper' not supported as upperdir


    This does not seem to be officially documented but makes sense that an overlay on an overlay does not work and is considered an unsupported filesystem as is even NTFS . Some admins/organizations try to use ecyptfs as a simple solution to encrypt the contents of Docker. Instead, you could probably........

  • Linux How To Upgrade To The Latest Kernel Debian Mint Ubuntu


    How to check what kernel version you have/currently running? uname -rm 5.4.0-91-generic x86_64 The above shows us that we are running 5.4.0-91-generic on the x86_64 architecture. The safest way is to stick with the same flavor eg if you're on generic, and say on kernel 5.4.0 then it makes sense to follow what is below. However, if you are migrating or dual booting between newer hardware (eg. you got a........

  • Linux how to keep command line bash process running if you are disconnected or need to logout of SSH remotely


    So you started a process or other important task that is remote but it is in the foreground and on a pts. This means if you background with Ctrl + Z or otherwise logout or get disconnected that the process will be stopped. Here is how you can solve the problem: 1.) Hit Ctrl + Z to suspend the process. 2.) Type bg to restore the process into the background. If you do a ps aux on the process you will see it was restored with the & at the end, which puts........

  • How to upgrade to the latest Python version on Linux Ubuntu Debian Mint 3.11


    A lot of developers want to go to 3.11 because of the speed improvements, but most distros never have the latest Python version. Using the deadsnakes third party repo is the easiest way aside from compiling it yourself (which is safer and recommended): Step 1 - Add the repo apt-add-repository ppa:deadsnakes/ppa If you get an error about requests then install it:........

  • How to install and configure haproxy on Linux Ubuntu Debian


    haproxy is one of the best known and widely used Open Source load balancers out there and a strong competitor to nginx. haproxy is used by many large sites per Wikipedia: HAProxy is used by a number of high-profile websites including GoDaddy, GitHub,........

  • talib/_ta_lib.c:747:10: fatal error: ta-lib/ta_defs.h: No such file or directory


    If you are installing ta-lib for Python and get this error then you can normally solve it by manually getting the ta-lib source files and compiling. tar -zxvf ta-lib-0.4.0-src.tar.gz cd ta-lib;./configure;make;make install Collecting ta-lib Downloading https://files.pythonhosted.org/packages/39/6f/6acaee2eac6afb2cc6a2adcb294080577f9983fbd2726395b9047c4e13ec/TA-Lib-0.4.26.tar.gz (272kB) &nbs........

  • PXE-E23 Error BOOTx64.EFI GRUB booting is 0 bytes tftp pxe dhcp solution NBP filesize is 0 Bytes


    Be very careful about what filename you specify in dhcpd.conf if you get an error like this: NBP filesize is 0 Bytes PXE-E23:Client received TFTP error from server. If you specify "BOOTx64.efi" then the file had better not be called "BOOTx64.EFI" as it is case sensitive. It's really a case of th........

  • Virtualbox Best Networking Mode In Lab/Work Environment without using NAT Network or Bridged


    Virtualbox is a very powerful tool, but for some use cases it is less than optimal. Say you are in a work, lab or other environment where you are not alone on the physical network and there could be overlap of IPs, but you need all of your VMs to be contactable from your host, VMs need to communicate with each other, and VMs need internet. NAT Network will give you VM to VM communication and internet, however, it is buggy and unstable. It also doesn't allow host to VM co........

  • debootstrap how to install Ubuntu, Mint, Debian install


    In this example we install debian 10 with --variant=minbase which gives us a minimal/tiny install. Don't use variant if you want the full size install. mkdir /tmp/deb10files debootstrap --variant=minbase buster /tmp/deb10files/ Did you get an error? debootstrap --variant=minbase buster /home/theuser/VMs/deb10files/ You'll get this error if you make a directory in your home........

  • Grandstream Phone Vulnerability Security Issue Remote Backdoor Connection to 207.246.119.209:3478


    Have you checked your router/firewall logs and disconcertingly see connections to an unknown IP207.246.119.209:3478 from your Grandstream VOIPphones? You're not alone and the Grandstream forums have discussed this issue. However, even their own staff d........

  • Linux How to Check Which NIC is Onboard eth0 or eth1 Ubuntu Centos Debian Mint


    So say you happen to have 2 NICs of the exact same chipset, they will generally show up as the same name, with possibly a different revision in lspci. Normally this is not an issue if you have a server with 4 NICs, generally the eth0 to eth3 appears from left to the right (or right to left on some vendors) so it doesn't take much figuring out. Generally if you have different chipsets for different NICs, it should be easy to know which one is eth0 or the first NIC in the OS.........

  • VboxManage VirtualBox NAT Network Issues Managment Troubleshooting


    If you find your NAT Network is not working properly, the first thing you may want to do is list the networks, check their status and make sure the Network is actually started and configured as you expect (eg. is DHCP on and enabled?). This is a long known, unresolved bug that seems to affect Version 6 randomly and disportionately on especially Mint 20/Ubuntu 18. https://www.virtualbox.org/ticket/1474........

  • Thunderbird Attachment Download Error Corrupt Wrong filesize of 29 or 27 bytes Solution


    This is an ongoing issue even with the latest Thunderbird 102.x where attachments downloaded via IMAP just won't save or will be corrupt which is a huge interruption to workflow or if you come back later to find out the file you thought you saved is invalid/corrupt and you have perhaps deleted the e-mail. How to solve the Thunderbird filesize attachment issue? 1. Click on "Settings". then go to "General". 2. Scroll to the bottom to find "Conf........

  • Generic IP Camera LAN Default IP Settings DVR


    If you are converting a generic wifi IP camera to ethernet, it may not be that simple as many are default hard coded to a static IP of 192.168.1.168 and login info admin/admin. From there you can login to the camera and assign it to DHCP by going to http://192.168.1.168 For security these cameras +DVR should be on a separate untagged VLAN or if possible a physically isolated non-internet connected switch/network. The reference below is applicable to many of the r........

  • RTL8812BU and RTL8822BU Linux Driver Ubuntu Setup Archer T3U Plus


    PCIID 2357:0138 First install your kernel headers/source: sudo apt install linux-headers-`uname -r` 1.) Clone this git repo git clone https://github.com/morrownr/88x2bu-20210702 2.) Run the install cd 88x2bu-20210702 ./install-driver.sh 3.) Load the driver mod........

  • Cisco UC CME How To Enable Licensed Features


    Router#show license Index 1 Feature: ipbasek9 Period left: Life time License Type: Permanent License State: Active, In Use License Count: Non-Counted Lic........

  • from pip._internal.cli.main import main File "/usr/local/lib/python3.5/dist-packages/pip/_internal/cli/main.py", line 60 sys.stderr.write(f"ERROR: {exc}") from pip._internal.cli.main import main File "/usr/local/lib/python3.5/dist-packag


    Solution for python pip3 not working anymore from pip._internal.cli.main import main File "/usr/local/lib/python3.5/dist-packages/pip/_internal/cli/main.py", line 60 sys.stderr.write(f"ERROR: {exc}") wget https://bootstrap.pypa.io/pip/3.5/get-pip.py python3 get-pip.py DEPRECATION: Python 3.5 reached the end of its life on September 13th, 20........

  • ModuleNotFoundError: No module named 'pip._internal' solution python


    pip3 install requests Traceback (most recent call last): File "/home/user/.local/bin/pip3", line 7, in from pip._internal.cli.main import main ModuleNotFoundError: No module named 'pip._internal' As a quick and temp fix call the OS installed python and not the user .local/bin installed pip3 /usr/bin/pip3 install requests Collecting requests Cache e........

  • Error: Failed to download metadata for repo 'appstream': Cannot prepare internal mirrorlist: No URLs in mirrorlist Solution for Centos8 yum package install error


    Are you getting this error in CentOS 8 when trying to use yum to install a package? Error: Failed to download metadata for repo 'appstream': Cannot prepare internal mirrorlist: No URLs in mirrorlist What we need to do is not use the automatic mirror list and manually set the base URL Solution sed -i 's/mirrorlist/#mirrorlist/g' /etc/yum.repos.d/CentOS* sed -i 's%#baseurl=http://mirror.centos.org%baseurl=........

  • i915 nouveau Nvidia GPU not starting lightdm Xorg failing solution for Could not determine valid watermarks for inherited state


    It may appear to be an Xorg or lightdm/gdm/mdm error but in reality for many users with this issue, it's a driver conflict and issue. I had a system that had two GPUs, an Intel and Nvidia GPU. The only thing that got it working was to remove the nouveau driver and blacklist it so it never came back, then the Intel GPU works fine without these issues. Solution sudo rmmod nouveau add nouveau/other driver to blacklist edit th........

  • amdgpu AMD GPU Xorg Won't Start [3576284.324] (EE) Segmentation fault at address 0x0 [3576284.325] (EE) Fatal server error: [3576284.325] (EE) Caught signal 11 (Segmentation fault). Server aborting


    Here is how Ifixed it on a Mint/Ubuntu install 1.) First download the latest AMDGPU-Pro driver from here: https://www.amd.com/en/support Navigate to your relevant video card: 2.) Download the installer One issue is that by default they give you a version for the latest version of........

  • symbol 'grub_calloc' not found grub boot error solution / fix


    I've encountered this after upgrading some Debian/Ubuntu/Mint based systems for no explicable reason, although there are some bug trackers on Ubuntu that document this: https://bugs.launchpad.net/ubuntu/+source/grub2/+bug/1889509 The short end of the solution is that you need to properly reinstall grub. 1.) Boot from a LiveCD 2.) Mount your root / filesystem and don't forget to mo........

  • How To Tell Which Repository a Package Comes From Debian Mint Ubuntu


    Just use apt-cache policy to find the repo of a package: apt-cache policy lxd lxd: Installed: 3.0.3-0ubuntu1~18.04.2 Candidate: 3.0.3-0ubuntu1~18.04.2 Version table: *** 3.0.3-0ubuntu1~18.04.2 500 500 http://archive.ubuntu.com/ubuntu bionic-updates/main amd64 Packages &nb........

  • Ubuntu Mint Debian Howto Execute Command / Script / Program Upon Wakeup From Sleep


    Sometimes manual intervention on various Linux system's, including Debian, is required to fix things after waking up from sleep. One persistent issue is the sound system / pulseaudio needing to be reset and not working until you do that after waking up. It's not clear if it's an OS issue itself or the sound driver, but this will fix things. Where do we put scripts or commands that need to be used upon wakeup automatically? /lib/systemd/syst........

  • MP3s Won't Play / ID3 Version 2.4 Issues in Cars and Other MP3 Players/CDs/DVDs Solution


    ID3 2.4 can cause various MP3 players, especially on vehicles or even computers, not to play or at least not to display the ID3 tags. In many cases though, since ID3 2.4 is much different than version 2.3, it will cause some players, especially in cars like Lexus not to play. Even on the computer, you may notice if you check the properties of the MP3 that it won't open or show any details (eg. frequency, bitrate and ID3 tags). One symptom of this in a vehicle (eg. Leuxs,........

  • How To Do Linux Network Bonding Teaming in Mint Debian Ubuntu


    Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows. There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........

  • LXC Containers LXD How to Install and Configure Tutorial Ubuntu Debian Mint


    If you are using mint, delete the preference that stops snap from installing (as it is required for lxc) sudo rm /etc/apt/preferences.d/nosnap.pref 1. Install lxd: sudo apt install lxd Issues install lxd or errors? Click here Debian at this time does not have lxd so you'll need to use snap: sudo apt in........

  • GlusterFS HowTo Tutorial For Distributed Storage in Docker, Kubernetes, LXC, KVM, Proxmox


    This can be used on almost anything, since Gluster is a userspace tool, based on FUSE. This means that all Gluster appears as to any application is just a directory. Applications don't need specific support for Gluster, so long as you can tell the application to use a certain directory for storage. One application can be for redundant and scaled storage, including for within Docker and Kubernetes, LXC, Proxmox, OpenStack, etc or just your image/web/video files or even da........

  • How To Enable Linux Swapfile Instead of Partition Ubuntu Mint Debian Centos


    This may be necessary if you have a VM or if for some reason you just want to be more efficient with your space and have the flexibility of changing your swap space at will. What we mean is the ability to use a "swap file" or similar to the Windows "pagefile" that normally resides on the root or c: partition of Windows. Here's all you have to do and then you to can have a single partiton with everything, including the swap file on the root partition if you........

  • WARNING: Can't download daily.cvd from db.local.clamav.net freshclam clamav error solution


    freshclam ClamAV update process started at Sun Mar 20 00:30:50 2022 WARNING: Your ClamAV installation is OUTDATED! WARNING: Local version: 0.100.3 Recommended version: 0.103.5 DON'T PANIC! Read https://www.clamav.net/documents/upgrading-clamav main.cld is up to date (version: 62, sigs: 6647427, f-level: 90, builder: sigmgr) WARNING: getpatch: Can't download daily-26337.cdiff from db.local.clamav.net WARNING:........

  • Debian Mint Ubuntu Which Package Provides missing top, ps and w Solution


    Install procps and it will install the other packages you need: apt install procps Reading package lists... Done Building dependency tree Reading state information... Done The following additional packages will be installed: libgpm2 libncurses6 libprocps7 lsb-base psmisc Suggested packages: gpm The following NEW packages will be ins........

  • Docker Tutorial HowTo Install Docker, Use and Create Docker Container Images Clustering Swarm Mode Monitoring Service Hosting Provider


    The Best Docker Tutorial for Beginners We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........

  • Zoom Password Error 'That passcode was incorrect' - Solution Wrong Passcode Wrong Meeting Name


    Have you been given a Zoom password that the meeting owner says is correct but it doesn't work anymore or never works? If the meeting name says "Zoom Meeting" and it's not really named that (which most meetings are not), then the issue is usually that there is an initial password to be able to join, aside from the passcode. It basically means that Zoom has deauthenticated you randomly or maybe after X amount of uses, without clicking on the Join Meeting URL which contains a........

  • How To Create OpenVPN Server for Secure Remote Corporate Access in Linux Debian/Mint/Ubuntu with client public key authentication


    Why choose OpenVPN instead of a firewall appliance? OpenVPN can be a reliable and easy replacement for traditional hardware or just be an additional tool that your company uses so that the firewall can focus on its job rather than acting as a VPNappliance at the same time. When comparing OpenVPN with traditional firewal........

  • HongKong VPS Server, Cloud, Dedicated Server, Co-Location, Datacenter The Best Guide on Hong Kong, China Internet IT/Computing


    In our 2024 VPS Server/Cloud Buyer's Guide, we place the location of your VPS/hosting/server as one of the priorities that is often overlooked. 2024 Update - Datacent........

  • tag#4 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE tag#4 Sense Key : Illegal Request [current] res 40/00:b4:98:02:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) solution


    You might assume you have a bad drive or the SATA interface/cable is bad, or the power supply is bad/weak to the drive. These are all possible issues, but definitely check your SATA cable for "twisting". It is a big issue because until the error stops or times out, your system will not boot (in my case this was the case even though the drive with the issue was not part of the OS or booting process at all). If you run an open rig that you move around often that ha........

  • Wazuh / OSSEC Install and Configuration Howto Tutorial Guide for Monitoring Agents SIEM


    How To Install Wazuh Server / Quickest Installation Wazuh (forked from the well known OSSEC project) is a full SIEM (Security Information Event Management) that works extremely well with the platforms it natively supports as an "Agent", which allows you to do scans of everything such as all processes running, CVE vulnerability check, incident reporting etc... Prerequisites: A lot of issues with Wazuh seem to be caused by i........

  • Ansible Tutorial - Playbook How To Install From Scratch and Deploy LAMP + Wordpress on Remote Server


    1. Let's work from an environment where we can install Ansible on. If you are using an older version of Linux based on Mint 18 or Ubuntu 16, you may want to get the PPA and get the latest version of Ansible that way: sudo apt install gpg sudo add-apt-repository ppa:ansible/ansible sudo apt update........

  • Proxmox Update Error https://enterprise.proxmox.com/debian/pve bullseye InRelease 401 Unauthorized [IP: 144.217.225.162 443]


    Are you getting this error in Proxmox while trying to apt update or install Ceph? apt update Hit:1 http://security.debian.org bullseye-security InRelease Err:2 https://enterprise.proxmox.com/debian/pve bullseye InRelease 401 Unauthorized [IP: 144.217.225.162 443] Hit:3 http://ftp.hk.debian.org/debian bullseye InRelease ........

  • Ubuntu Linux Mint - Volume Control Stopped Working


    Volume control will often stop working, if your sound server (normally pulseaudio) dies or restarts whether by itself or by you. The reason pulseaudio may need to be restarted is due to some sort of crash or other issue that prevents sound from working (normally restarting or doing a killall pulseaudio fixes things). However, you will normally find at least in OS's like Ubuntu/Mint 16/18+ that you cannot control the volume whether adjusting the level, changing input/outputs and........

  • Linux Ubuntu Debian Centos Mint - How To Check if Intel VT-x or AMD-V Hardware Virtualization is Enabled?


    From the terminal do this: cat /proc/cpuinfo|grep -E "svm|vmx" You should get output like this(svm = AMD-v and vmx=Intel-VTx): flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc cpuid aperfmperf pni pclmulqd........

  • How to install Kubernetes with microk8s and deploy apps on Debian/Mint/Ubuntu Linux


    Kubernetes Easy Beginners Tutorial/Architecture Guide Kubernetes is known as container orchestration and we should start at explaining the container part of it. A Container is what runs the actual application and based on an Image, and are more comparable to something like an LXC Container, Virtuozzo/OpenVZ using the Linux Kernel Namespaces feature. Containers run these images as independent, isolated operating environments under the O........

  • ksnapshot missing in Ubuntu and Linux Mint Solution


    It has been renamed to kde-spectacle so you install it like so: sudo apt install kde-spectacle You'll find it in your start menu listed as "Take Screenshot"........

  • bash how to hide username/customize prompt Linux Debian Redhat Ubuntu Solution


    Just edit your ~/.bashrc and add this at the very end: export PS1="realtechtalk.com" Then your prompt will look like this: bladeblox:uptime 08:47:14 up 48 min, 1 user, load average: 1.00, 1.07, 0.96 If you wanted a dollar sign at the end then you would change it like this: export PS1=&........

  • EFI PXE grub2 Howto guide for Linux EFI PXE Booting on Debian, Mint, Ubuntu, RHEL


    Just a quick note and warning is that if you are testing to see if EFIPXE booting works on a VM, MAKE SURE it actually works. For example Iinitially tested using my Distro's QEMU 2.5+dfsg-5ubuntu10.46 and ovmf BIOS firmware (OVMF supports EFI). However, I found on old versions of QEMU (like 2.5), EFIbooting with GRUB NEVER works so it may appear that you have made a mistake when everything is fine when you boot a physi........

  • Juniper JunOS Command Overview and Howtos Switch, Router, Firewall Tutorial Guide


    Enable "cli" mode equivalent in JunOS cli Configure Mode configure So rather than going to the console on a Cisco switch and typing "enable" and then "conf t", the equivalent in JunOS is "cli" and "configure". How Do You Apply Changes You've Made? You can make all kinds of changes to the switch, but remember they are not........

  • QEMU KVM Keyboard Problems Not Working Right Repeating Characters, Ctrl+C Copy and Paste not working right when using PS2 mouse in guests Solution


    It seems that QEMU/KVM's default PS2 mouse and keyboard doesn't work right in most cases. I have especially observed issues using Ctrl+C and Ctrl+V and in Linux you may see repeated key presses in the terminal and you will wonder why you copied something and it's not in the clipboard when you try to paste. The way to temporarily fix it is to press the key that is repeating once(works in Linux but not really in Windows). Sometimes when moving your mouse it will also s........

  • Mikrotik RouterOS CHR/ISO Basic and Quick Setup Howto Guide


    Many people may not be aware that you can turn commodity hardware into a Mikrotik OS and there are various options which is "CHR" (Cloud Hosted Router) which is a VMimage meant for Virtualization only (seriously, I've tried to dd the image to a physical server and it just crashed as it does not contain any drivers for physical). One note as well if you are trying to do a baremetal install you may get an error "Error Loading Operating System" or........

  • CentOS 7 8 yum error Trying other mirror. To address this issue please refer to the below wiki article


    The below appears at first to be a bad mirror DNS error, but if you've ruled that out you just need to clear your broken yum cache and things will be good. yum update Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * base: centos.01link.hk * extras: centos.01link.hk * updates: centos.01link.hk http://mirror.worria.com/centos/7.8.2003/os/x86_64/repodata/repomd.xml: [Errno 14] HTTP Error 404 - Not........

  • Scanner not working in Linux Ubuntu Fedora Mint Debian over the network? Use sane-airscan!


    I have a Canon MF642c and the scanner wouldn't work. I tried to use saned but it didn't work with the BJNPlike it did for some other Canon models. Introducing sane-airscan with packages for the most common distributions: https://software.opensuse.org/download.html?project=home%3Apzz&package=sane-airscan http........

  • Huion and Wacom Tablets How To Install in Linux Mint / Ubuntu and make the stylus work properly


    It took a lot of fiddling to make a Huion Kamvas 13 Pro work in Linux but it simple once you know what to do. Don't bother searching as it is unlkely there is a guide out there that will actually make your tablet work. It mainly comes down to the fact that the hid_uclogic kernel module is buggy or doesn't support MANYof these wacom based/Huion tablets properly. What was happening with me is that Ihad the Kamvas 13 Huion setup as a secondary screen/monitor.&nb........

  • ffmpeg how to concat and join two video clips


    This normally works but if not use my mencoder solution if the output video does not play past the joined time. the contents of list.txt need to look like this: file somefile.mp4 file somefile2.mp4 then run ffmpeg ffmpeg -f concat -i list.txt -c copy CME-2-router-dial-peer-final.mp4 The result is almost instant joining since there is no video processing since we are........

  • How To Replace Audio Track of Video using ffmpeg


    A very common use case is that you don't want to waste time using a video editor that requires you to open it up and manually import the video clip and audio clip, then manually delete the old audio track and import the video and new audio. That's too much work and time since we don't want to go through the hassle. ffmpeg is our solution, all we have to do is specify 3 variables and we're done! -i Windows2019-Server-Noaudio.mp4 is our in........

  • dynagen / dynamips 100% high CPU usage solution - how to set the idlepc value


    The idlepc value is very important to dynamips and it is both image and often CPU dependent. There is no "magic"value that will work for all images and all CPUs so this is why I'll show you a quick and handy way. Also don't be disappointed, some values do not work well but idlepc gives you several. For example in my example below #6 didn't help at all but #7 got me down to about 6% CPU from 99-100%. *Befo........

  • How To Setup a Cisco CME (Cisco Manager Express) Virtual Router under Linux using dynamips and dynagen


    This tutorial will get your router up and running using emulation tools. In this case we'll be getting a Cisco C7206 (C7200 series) VXR router going which also supports SCCP VOIP services. dynamips is the emulator itself and dynagen is the front-end tool that helps us control everything. It is used by tools such as gns3 and eve-ng. Together the two tools (dynamips and dynagen) allow us to create and emulate REAL router........

  • apcupsd how to setup and monitor APC UPS units


    It really seems limited in that it can mainly give you the things you would see on the physical unit such as load etc.. wget https://downloads.sourceforge.net/project/apcupsd/apcupsd%20-%20Stable/3.14.14/apcupsd-3.14.14.tar.gz?r=https%3A%2F%2Fsourceforge.net%2Fprojects%2Fapcupsd%2Ffiles%2Flatest%2Fdownload&ts=1598115866 tar -zxvf apcupsd-3.14.14.tar.gz cd apcupsd-3.14.14 [root@somebox apcupsd-3.14.14]# ./conf........

  • How To Password Reset, Recover, Bypass, Remove and Unlock on Windows 10,8,7,Vista,XP,NT,2000,2003,2008,2012,2016,2019 Administrative Login Programs


    If you've come here, don't be embarraassed, working in IT, this is the MOST common computer problem that almost everyone will encounter. The reason why I'm doing this post is because I've seen an increase from colleagues and admins having this problem and many times it's not even your fault. A common scenario is that someone acquires a new or used computer which they weren't given the password for. Fortunately Ihave a detailed list of all the options whether free or pa........

  • Linux NIC connecting at 100M instead of 1000M gigabit speeds? It could be overheating


    I was using a small box as a router and one of the ports started going off and coming back at 100M. I truly believe it is simply that it was a case of overheating. Although CPUtemps were only about 67 degrees, the physical box itself was almost burning hot. Isolved the cooling issue and never had the issue again. Jul 28 15:09:27 swithbox kernel: e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx Jul 28 15:09:28 swithbox kernel:........

  • CentOS 6 impossible to compile a newer libguestfs


    yum -y install gcc make gperf genisoimage flex bison ncurses ncurses-devel pcre-devel augeas-devel augeas readline-devel checking for cpio... cpio checking for gperf... no configure: error: gperf must be installed configure: error: Package requirements (augeas >= 1.2.0) were not met: Requested 'augeas >= 1.2.0' but version of augeas is 1.0.0 yum remove augeas augeas-libs augeas-devel wget http://downl........

  • How To Get Started on Ubuntu with gpt-2 OpenAI Text Prediction


    apt install software-properties-common add-apt-repository ppa:deadsnakes/ppa apt update apt install python3-pip apt install python3.7 curl gnupg python3.7-dev git ln -s /usr/bin/python3.7 /usr/bin/python3 pip3 install numpy keras_preprocessing curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add - echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........

  • Linux How To Change NIC Name to eth0 instead of enps33 or enp0s25


    Most newer distros inexplicably cause your NIC to have what Icall "random" non-standard name conventions because of systemd. This is a big problem for many people and especially those running servers. Imagine that you have a static IPconfigured for ens33 but then the hard disk is moved to a newer system, the NIC could be anything from ens33 to enp0s1, meaning that manual intervention is required to go and update the NIC config file (eg. /etc/network/interfa........

  • Asterisk Does Not Retry When Authentication Fails


    When authentication times out that is one thing, but when it just fails like below Asterisk by default will not re-register until you the admin reload the sip or asterisk server: voipserver*CLI> sip show registry Host dnsmgr Username Refresh State&........

  • Linux Debian Ubuntu How To Install PEPPER Faster and Latest Adobe Flash Player in Firefox


    Just run this apt install command sudo apt install pepperflashplugin-nonfree browser-plugin-freshplayer-pepperflash After this restart your browser and check Adobe's site to verify if your Pepper flash is working and showing at least version 32. https://helpx.adobe.com/flash-player.html As you'll see below it will download the latest version which is currently 32 and this was not possible with the old/crappy deprecated adobe-flash plu........

  • How To Speed Up Linux Ubuntu and Debian Based Computers By Improving CPU Performance and Changing the CPU Governor


    I used to believe that for Desktops especially that the "ondemand" CPUfrequency changing that kernels included with Ubuntu and Debian based distros have would be sufficient for snappy performance. However, you can feel the lack of performance on the fastest computer if you have ondemand. A lot of times even under high load 100% of your CPUfrequency in MHz will not be used. For example a 2.8Ghz CPUmay only run at 1.8MHz or even .9GHz. Now........

  • How To Install NextCloud on Centos 7 and Centos 8


    yum -y install wget unzip wget https://download.nextcloud.com/server/releases/nextcloud-18.0.2.zip unzip nextcloud-18.0.2.zip yum -y install php php-mysqlnd php-json php-zip php-dom php-xml php-libxml php-mbstring php-gd mysql mysql-server Last metadata expiration check: 0:58:02 ago on Fri 13 Mar 2020 02:12:49 PM EDT. Dependencies resolved. ===================================================================........

  • ZTE Camera Cannot Work unable to connect to camera. Camera has been disabled becaue of security policies or is being used by other apps


    unable to connect to camera. Camera has been disabled becaue of security policies or is being used by other apps They say to do a factory reset but in some cases it doesn't work and the camera mysteriously just won't work so it appears to be a hardware error if that happens.........

  • How To Install OpenProject on Centos 7 Step-by-Step Guide


    There are a few caveats that may not be obvious to everyone so I am going to cover them here but keep this in mind before starting. Before starting install epel or you will be missing tesseract: yum -y install epel-release #1) When you specify your SSL certificate with a full path, it really needs to exist where you tell it to (including the default location of /etc/ssl/certs and /etc/ssl/c........

  • Ubuntu Debian Linux Cannot Install Wine Solution - wine1.6 : Depends: wine1.6-i386 (= 1:1.6.2-0ubuntu14.2) but it is not installable wine1.4 : Depends: wine1.6 but it is not going to be installed


    If you've ever gotten errors like this the solution is simple, you need i386 enabled on your 64-bit install because wine depends on some 32-bit x86 libraries: dpkg --add-architecture i386 apt update apt install wine After that it will install just fine. apt install wine Reading package lists... Done Building dependency tree Reading state information... Done........

  • How To Install python 3.4 3.5 and up on Linux with wine - Working Solution


    This is sure simple if you follow the guide but it took a lot of hacking around to make this work on Debian/Ubuntu! Now before you ask why bother running wine and python, the reason is because Python executables are NOT cross-platform. If you run pyinstaller in Linux, that binary will only run on Linux and the same if you do it in Windows. So it is preferable if you have a single environment that you can create Linux and Windows binaries from rather than running 2 separate........

  • selenium.common.exceptions.WebDriverException: Message: Can not connect to the Service geckodriver


    A lot of times this is actually caused by simply not having Firefox installed at all. selenium.common.exceptions.WebDriverException: Message: Can not connect to the Service geckodriver https://github.com/mozilla/geckodriver/issues/270........

  • Ubuntu Linux Mint Debian xorg performance and tear-free tuning for AMD Radeon Based Cards


    I find that the default settings for the radeon driver that is applied to most AMD cards is horrible. For example by default TearFree is not enabled and it causes videos to have some kind of square artifacts. Here are the settings I have found most suitable for AMD cards: You need to create file in the following path and restart Xorg or your computer to apply it: *Beware that making a mistake here will possibly make your computer........

  • Linux 3D Performance benchmarks with glxgears 59-60fps solution


    You need to disable vsync like this when running glxgears: vblank_mode=0 glxgears For Nvidia drivers do this: __GL_SYNC_TO_VBLANK=0 glxgears Notice the higher than 59-60 fps results with vblank_mode=0: ATTENTION: default value of option vblank_mode overridden by environment. 7919 frames in 5.0 seconds = 1583.704 FPS 8187 frames in 5.0 seconds = 1637.266 FPS........

  • How To Install Asterisk 16 17 on Debian Ubuntu Linux


    Downloading and compiling from source to get the latest version of Asterisk is really simple with this guide. apt install gcc make g++ libedit-dev uuid-dev libjansson-dev apt install libxml2-dev sqlite3 libsqlite3-dev wget http://downloads.asterisk.org/pub/telephony/asterisk/asterisk-16-current.tar.gz tar -zxvf asterisk-16-current.tar.gz cd asterisk-16.6.2/ ./configure If you get this error change y........

  • Cannot Print PDF Solution and Howto Resize


    If you can print other PDFs but not a particular one it is very likely that the PDF size is A4 (the longer, skinnier Asian paper size) instead of the North American letter size ( 8.5" x 11"). This breaks printing in most cases. Or it may print if you find a program that ignores the size issue. Here is an example of an A4 being rejected by a printer in Ubuntu Linux via CUPS Cannot print PDF CUPS Samsung C460: Processin........

  • Apache Cannot Start Listening Already on 0.0.0.0


    A lot of times busy servers will have this issue and you cannot even force kill -9 the apachectl or httpd process: [root@apachebox stats]# ps aux|grep httpd root 1547 0.0 0.2 495452 32396 ? Ds Sep08 3:23 /usr/sbin/httpd root 3543 0.0 0.0 6448 724 pts/1 S+ 13:11&nbs........

  • bash script kill whois or other command that is running for too long


    Adjust to suit your needs. Currently this would kill any whois process running for more than 30 seconds or more than 1 minute. Add it as a cronjob. The motivation is that some commands have no timeout and just end up using up CPU and memory for no reason while never exiting to free resources. #!/bin/bash IFS=$(echo -en "nb") for pid in `ps aux|grep whois`; do echo "pid=::$pid::&qu........

  • Linux tftp listens on all interfaces and IPs by DEFAULT Security Risk Hole Solution


    Just edit your tftp file for xinetd like this: *Change the IPto be the IPof the interface you want to listen on. To test if your tftp is available on a certain IP range use nc -u yourip 69 to see if you can still connect (/var/log/messages or /var/log/syslog) should show the connection if it is open. Oct 13 23:20:34 01 xinetd[26631]: Started working: 1 available servic........

  • python import docx error


    sudo pip3 install python-docx [sudo] password for : Downloading/unpacking python-docx Downloading python-docx-0.8.10.tar.gz (5.5MB): 5.5MB downloaded Running setup.py (path:/tmp/pip_build_root/python-docx/setup.py) egg_info for package python-docx no previously-included directories found matching 'docs/.build' warning: no previously-included files matching '.DS_Store' foun........

  • Cisco Unified Communications Manager Express Cheatsheet CUCME CME Tutorial Guide


    Video Links: How To Setup 2 Phones on a Single CME Router and get the GUI going. How to use Dialpeers with CME with two routers How to implement call restrictions using COR / Class of Restriction Set your clock: HH:MM:SS clock set 22:00:00 24 September 2024........

  • Wordpress overwrites and wipes out custom htaccess rules and changes soluton


    cat .htaccess RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . index.php [L] I keep reading there is a "# BEGIN WordPress" and a "# END WordPress" in the wordpress htaccess above but there is clearly not. Even more strange is that my permissions are just 444 (read only). so i changed it........

  • Apache htaccess and mod_rewrite how to redirect and force all URLs and visitors to the SSL / HTTPS version


    It is really simple using .htaccess with mod_rewrite. Here is all you need: RewriteCond %{SERVER_PORT} 80 RewriteRule ^(.*)$ https://site.com/$1 [R=301,L] Another more graceful way is to use the %{SERVER_NAME}variable to make it dynamic. Just be careful that the server name will always match what you expect. (eg. if you are doing load balancing or clustering what if the server name may be somethi........

  • Virtualbox vbox not starting


    If you've just installed VBox and it is not starting or working, the most common problem is usually that you don't have your kernel source installed, which means there is no kernel driver for vbox so it can't work. You may get an error that says "Kernel driver not installed" in your Virtualbox. So the first thing you should do is install your kernel source by running this: sudo apt-get install linux-headers-`uname -r`........

  • Ubuntu/Gnome/Mint/Centos How To Take a partial screenshot


    By default printscreen or alt print screen will get the whole desktop or the application in focus, respectively. But what if you want to select a portion of the screen? gnome-screenshot: ksnapshot compiz This is a nicely integrated solution sudo apt-get install compizconfig-s........

  • Cisco IP Phone How To Reset To Factory Settings Instructions CP 9971, 8800, 8900, 8845, 8851, 8841, 8831, 7961, 7960, 7945, 7942, 7941, 7940.


    This would be crucial especially if the phone is hardened, not being able to reset or change settings could prevent a phone registering in a new environment or even when migrating from office to office. This applies even if you are trying to migrate the phone to another platform such as Asterisk/FreePBX etc... This guide applies to nearly all of the Cisco IP phones that you would use in CME or CUCM from several years ago including models: 9900, 9971, 8800, 8900, 8845, 8851, 8841........

  • Cisco Unified Communications Manager / CUCM IP 8.6,10,12 Install Error Solution


    Install Errors on Version 12: This error happened on QEMU emulator version 2.11.1 pve-qemu-kvm_2.11.1-5 on Proxmox/Debian but installing on QEMU.12 on Centos 6 did not produce the error. *Update it is not related to the OS or QEMU version. This happened in Centos 6 too after a second install. What really causes this even though you successfully install........

  • Cisco Unified Communications Manager 12 Install Errors on Proxmox/KVM


    The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs. qemu-kvm command: /usr/libexec/qemu-kvm -version QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard ........

  • Windows 7, 8, 10, Windows Server 2008, 2012, 2016, 2019 How To AC97 Audio Drivers and Other Unsigned Drivers


    Oops did you get this error trying to install an oldschool driver and think it is hopeless in a new version of Windows? First of all it is almost never a program compatibility issue: ........

  • Skype For Business 2015 and 2019 Guide, Reference, Howto and Troubleshooting Solutions


    https://docs.microsoft.com/en-us/powershell/module/skype/?view=skype-ps Troubleshooting Client Connectivity Issues The first step is to enable full logging in the Skype Client itself and then check the log on the client side. In Windows this normally means going to the Skype client "settings" and then "Enable Full Logging". Aft........

  • Cisco CUCM Unified Communication Manager Howto Guide and Tutorials


    Install Issues: How to Make CUCM iso /modify to work on non-VMWare machines like QEMU/Xen/OpenStack If you get kernel panic errors in VBOX usually disabling Nested Paging will fix the issue (thanks to Mark). ks_pre.sh error is caused by having the wrong VDX pattern (change it do sd per guide link above) and/or the wrong VMSpecs (Cisco req........

  • SSH persistent and automatic login script for proxy


    #!/bin/bash sshcommand="ssh -N -R 20000:localhost:22 user@8.8.8.8" result=`ps aux|grep $sshcommand"|grep -v grep` if [ -z "$result" ]; then echo "we are going to connect" $sshcommand else echo "we are already connected" fi This is a handy script you can use and then add it to cron. Save........

  • How To Use Letsencrypt SSL/TLS Encryption to Create Certificates without installing on the target machine


    For some reason, perhaps you don't want to run a daemon or let Letsencrypt have access to your production server. There is a way to use it like a normal CSR/CA setup in manual mode. ./letsencrypt-auto certonly --manual -d realtechtalk.com - www.realtechtalk.com   Eventually you will get prompted to create a certain path and file with certain data: Create a file containing just this data: Casdfasfadsfsad........

  • Cisco Router Setup Guide and Tutorial Howto With Commands and Examples


    In most of the Cisco router IOS I find the ports like ge0/0 ge0/1 and ge0/2 or whatever your ports are down. They will not even give you a link light. So one of the first tasks should be getting the port you are working with up. In my case the first goal is often connectivity with the LAN and WAN. LAN = your local area network (eg. in the office/home ) WAN= your ISP/public internet (eg. fiber/cable/dsl/ethernet).........

  • Linux Bash Script To List All Connected IPs and their network name


    for ip in `netstat -nt|awk '{ print $5 }'|cut -d ":" -f 1|tail -n +3|sort|uniq`; do echo $ip;whois $ip|grep -i netname;echo "---------------------------" done 77.88.47.40 netname: YANDEX-77-88-47 --------------------------- 40.77.167.5 ------........

  • Cisco DHCP Snooping Relay Setup Information


    Switch#show ip dhcp snooping Switch DHCP snooping is disabled DHCP snooping is configured on following VLANs: 1 Insertion of option 82 is enabled circuit-id format: vlan-mod-port remote-id format: MAC Option 82 on untrusted port is not allowed Verification of hwaddr field is enabled Interface&nb........

  • Centos 7 Reallocate logical volume space to another


    Do you hate how Centos 7 defaults to allocating most of your valuable space to /home even though it is a production server? Here is a quick guide on how to take back that space live, while online (of course make sure you have backups just in case something goes wrong!): First we will reduce our home dir by 100G: lvreduce -L -100G /dev/mapper/centos-home WARNING: Reducing active and open logical volume to ........

  • Using Microsoft's Group Policy Management Editor (GPME) To Change Default Permissions and Internet Explorer Security Settings


    The defaults in Windows 2016 server leave clients crippled so they can't even download basic files or software. But Group Policy Management Editor comes to our rescue! Use cmd or Powershell and run: gpme.msc Choose your domain/computer and then navigate like below and create a new menu entry for IE11 or whatever your version is. Don't be worried if the highest version is IE10 it means that it applies to IE10 AND above.........

  • PHP Issues With Decoding Strange Smart Quotes And Non-Standard ASCII Characters


    When using strip_tags and html_entity_decode with PHPit often breaks and produces annoying diamonds with question marks. It is probably because of characters like these: … (looks like 3 dots but it is a single weird character). ’ (looks like a normal apostraphe but it is not) ” (looks like a normal double quote but it is not). An easy way to sort this out is to copy the above and search in an ASCII table to extend the functional........

  • Linux use growisofs to burn a larger file on a BD-R / Bluray Disc


    growisofs -Z /dev/sr0 critical.tar.gz.gpg Executing 'genisoimage critical.tar.gz.gpg | builtin_dd of=/dev/sr0 obs=32k seek=0' I: -input-charset not specified, using utf-8 (detected in locale settings) File critical.tar.gz.gpg is larger than 4GiB-1. -allow-limited-size was not specified. There is no way do represent this file size. Aborting. :-( write failed: Input/output error #remember to us........

  • Centos 6 / 7 / 8 How To Change Default nameservers in /etc/resolv.conf when using DHCP / dhclient


    First we need to create dhclient.conf if it doesn't exist or edit it: vi /etc/dhclient/dhclient.conf #add this line at the top add the IPs as commas they will be the highest priority nameservers and whatever your ISP gives you will be used after these one (good for DNS backup) prepend domain-name-servers 127.0.0.1,10.10.25.8; After you restart your network or run dhclient again you should see the contents of........

  • iSCSI on Centos 7 Configuration and Setup Guide for Initiator and Target


    initiator = client target = server These are the first concepts you should understand which is that in iscsi essentially the "initiator" is the client and the "target" is the server. iSCSI is derived from the old fashioned SCSI that us oldtimers grew to love. The "i" stands for Internet and the SCSI stands for "Small Computers Systems Interface" (SCSI). iSCSI Target (Server)Setup targetcli is the pac........

  • How Does Cisco CUCM (Cisco Unified Communication Manager) Work?


    Cisco's CUCM (Cisco Unified Communication Manager) is a system that combines voice, video, data and mobile products into a single unified management suite. At its core, the CUCMis like a "Super PBX" that controls the flow of all communications through an organization even single or multiple site deployments. Cisco's CUCMmakes communication more effective and simple through centralized management and unification of communications resources.........

  • systemd management using systemctl and journalctl to check systemd logs


    systemd is like the service manager for your Centos and other modern Linux distributions (including Debian/Mint/Ubuntu) allows you to enable services, stop them, restart them, check their status and even reboot your system. The key commands or arguments you will use with systemctl are the following: Unit Commands: list-units [PATTERN...] List loaded units &nbs........

  • What is /dev/pts and why do we need it in Linux?


    A quick check in /dev/pts shows a lot of entries but what are they for?: ls /dev/pts 0 10 12 14 16 18 2 21 23 25 27 29 30 32 4 6 8 ptmx 1 11 13 15 17 19 20 22 24 26 28 3 31 33 5 7 9 Basically they are pseudo-termi........

  • Linux Permissions and Groups Real Usecase for Group Access


    Ihave a directory structure which the primary user needs full access on but wanted a user to access only a specific directory within the main directory (so they could write in there only and nowhere else). Here's what Idid: [root@compevo8001 dllnow]# ls -alh drwxrwxr-x 2 someuser software 4.0K Oct 19 2017 ExpireYMD-2017-11-20 drwxrwxr-x 2 someuser software 4.0K Nov 19 2017 ExpireYMD-20........

  • Centos 7 - Convert Minimal to Graphical GUI GNOME or KDE Desktop


    Did you just install the minimal version by accident or want to install the GUI? No need to reinstall just tell yum to do the work for you! You could actually have both installed and choose one as your preference on demand (although many people prefer GNOME's simplicity). Step 1.) Install Gnome and/or KDE. To install the GNOME Desktop on Centos 7: yum -y groups install "GNOME Desktop" To........

  • How to download gajim 0.16.9 XMPP/Jabber client so you can use OMEMO encryption


    #Linux Mint 18.2 how to install gajim .16.9 so you can use OMEMO encryption: sudo apt-get install python-axolotl python-nbxmpp wget https://gajim.org/downloads/0.16/gajim-0.16.9.tar.gz tar -zxvf gajim-0.16.9.tar.gz cd gajim-0.16.9 ./autogen.sh ;make;sudo make install #if you get this error you need to get a newer python-nbxmpp from here: gajim Gajim needs python-nbxmpp >= 0.6.1 to run. Quiting...........

  • HP DL385 G7 Linux BIOS Update Flash


    wget https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe --2018-08-16 05:11:16-- https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe Resolving downloads.linux.hpe.com (downloads.linux.hpe.com)... 15.249.152.85 Connecting to downloads.linux.hpe.com (downloads.linux.hpe.com)|15.249.152.85|:443... connected. HTTP request sent, awaiting response... 200 OK Length: 1525561 (1.5........

  • hwloc-nox set CPU affinity in Linux


    sudo apt-get install hwloc-nox Reading package lists... Done Building dependency tree Reading state information... Done The following NEW packages will be installed: hwloc-nox 0 upgraded, 1 newly installed, 0 to remove and 530 not upgraded. Need to get 151 kB of archives. After this operation, 453 kB of additional disk space will be used. Get:1 http://archive.ubuntu.com/ubunt........

  • Cannot install moodle


    After starting the install it stalls here: admin/index.php?cache=0&agreelicense=1&confirmrelease=1&lang=en If you manually refresh you get a Plugins check screen: Installation System Moodle second step fails just blank screen: https://domain.la/user/editadvanced.php?id=2 Solution: give up and choose something else it shouldn't be thi........

  • vmkping -I vmk1 10.0.2.69 PING 10.0.2.69 (10.0.2.69): 56 data bytes sendto() failed (Host is down)


    [root@localhost:~] vmkping -I vmk1 10.0.2.69 PING 10.0.2.69 (10.0.2.69): 56 data bytes sendto() failed (Host is down) vsphere distributed switch vmotion not working [root@localhost:~] esxcfg-route -l VMkernel Routes: Network Netmask Gateway Interface&........

  • gvfs mount in /run/user cannot be accessed or displayed wrong permissions Error: Location is already mounted


    You get errors like below and see you have all question marks for the permissions if you go to /run/user/1000/gvfs If you try to access the mounted share such as anything mounted as gvfs like an SSH share in your file manager you may get an error like this. It generally means an interruption in communication or a fault with gvfsd has caused it. Solutio........

  • PHP Displaying Blank Page on Apache


    Almost always the reason will be that the php.so file is missing but also that php.conf is misconfigured. In the problem machine it is actually PHP7 installed so if you reference PHP5 of course things wil be broken! Take for example here: cat /etc/httpd/conf.d/php.conf # # PHP is an HTML-embedded scripting language which attempts to make it # easy for developers to write dynamica........

  • VMWare ESXi 6.7 SSH/PowerShell CLI Commands


    [root@localhost:~] BootModuleConfig.sh echo host-ind nfcd........

  • VMWare Vsphere VCSA Graphical Install Creates json


    yes it does create its own json ============================================ cat /tmp/vcsaUiInstaller/ovftool-20180809-175238948-20180809-175603497.log |grep -i json 2018-08-09T17:56:04.238-07:00 verbose OVFTool[30966] [Originator@6876 sub=Default] Manifest file entry: SHA1(VMware-vCenter-Server-Appliance-6.7.0.12000-8832884_OVF10-file1.json) = 1deb658c724767697587d5909c4051c01813e6a1 --> ........

  • Debian Mint Ubuntu compiling xmr-stak


    sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3 sudo apt-get install libcurl4-gnutls-dev git clone https://github.com/wolf9466/cpuminer-multi sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev git clone https://github.com/fireice-uk/xmr-stak-cpu.git make install cd bin chmod +x xmr-stak-cpu ./xmr-stak -O xmr........

  • [warn] VirtualHost 10.2.5.101:443 overlaps with VirtualHost 10.2.5.101:443, the first has precedence, perhaps you need a NameVirtualHost directive


    [root@thetor2017 conf]# service httpd restart Stopping httpd: [ OK ] Starting httpd: WARNING: MaxClients of 3000 exceeds ServerLimit value of 300 servers, lowering MaxClients to 300. To increase........

  • Ethereum Client Errors


    INFO [07-19|12:11:51] Imported new block receipts count=590 elapsed=8.440s bytes=74117699 number=4870906 hash=6bc60b…934753 ignored=0 INFO [07-19|12:11:57] Imported new state entries count=499 elapsed=9.963ms processed=71076 pending=1526 retry=2&nbs........

  • PayPal IPN Failed "result: IPN Handshake Invalid"


    This is often the result of PayPal's "item name" or another name having invalid characters or not supporting Unicode. 173.0.81.1 - - [17/Jul/2018:13:39:45 -0400] "POST //modules/gateways/callback/paypal.php HTTP/1.1" 406 - "-" "PayPal IPN ( https://www.paypal.com/ipn )" A good clue is if you check the debug output of the IPNand find a mandatory column empty. ........

  • Linux Centos 7 HowTo Install Yarn


    https://yarnpkg.com/lang/en/docs/install/#centos-stable curl --silent --location https://dl.yarnpkg.com/rpm/yarn.repo | tee /etc/yum.repos.d/yarn.repo If you need node.js: curl --silent --location https://rpm.nodesource.com/setup_6.x | bash - yum install nodejs yarn........

  • VMWare 6.7 VCSA VSphere ESXi Management SSO Install Guide on Linux using the CLI


    #mount the VCSA DVD mount /dev/sr0 /mnt/cd #alternatively you could mount the iso directly mount -o loop vcsa.iso /your/mount/path #for this purpose we are using the CLI installer on Linux cd /mnt/cd/vcsa-cli-installer/lin64 #no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file ./vcsa-deploy Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........

  • Hard Drive Serial Number Examples


    The reason for this article is because a lot of us don't physically see our hard drives they are often remote in a datacenter etc and the actual serial number we see in SMART is not enough to check for some manufacturers. A good example is our first one the Toshiba === START OF INFORMATION SECTION === Device Model: TOSHIBA DT01ACA200 Serial Number: 33FMDW4AS........

  • Cannot create gradle for conversations


    The main issue is it looks like Java is not configured to accept the invalid ssl cert that is coming from the download location. Exception in thread "main" java.lang.RuntimeException: javax.net.ssl.SSLException: java.security.ProviderException: java.security.InvalidKeyException: EC parameters error export ANDROID_HOME=/home/user/Downloads/tools/ Conversations-master$ ./gradlew Downloading https://services.gradle.org/distributions/grad........

  • not allowed to execute '/usr/bin/apt-get install eclipse' as root linux sudo user permisson issue and solution


    This is most likely to happen on a normal GUI system like Ubuntu or Linux Mint. If you or the user is meant to have sudo / root privileges it is as simple as editing the following files: Now assume your username is "iamtheuser" vi /etc/group adm:x:4:syslog,iamtheuser sudo:x:27:anotheruser,iamtheuser Find the above lines and add a comma and "ia........

  • Linux Mint Black Screen after boot no graphics solution


    This is not the normal "black screen"issue and I was shocked to eventually find out why. The normal advice of reconfiguring Xorg didn't work. Even booting into "Recovery Mode" did not help. Here is the short end of the stick that fixed it: sudo apt-get install mdm mate-desktop-environment Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled. This must be whe........

  • Centos PXEBoot NetInstall Failure - Pane is dead


    ValueError: new value non-existent xfs filesystem is not valid as a default fs type Pane is dead From what Iread this is misleading and has to do with the fact that the initrd and kernel are mismatched. This is a hard situation because for some older hardware Iam using the Centos Plus kernel which has modules that Irequire for an older server/NIC. This seems to have cropped up in the past few months and there is no simple fix........

  • Intel NUC J3455 Linux Kernel freeze slowness 4.4.98 errors


    It looks like this has something to do with APIC but I am not sure. I have similar CPUs with a different MB and BIOS that work fine on the same type of kernel. A lot of time the issue is because of the C-step setting in the BIOS. The same thing happened on the 2.6 kernel with Centos 6 but this is a homebrew 4.4 kernel soI am not sure why it is happening when even Centos 7 (3.2) kernel works OK. Solution - It comes down to the BIOS set........

  • imagemagick convert to chop off top of image


    This is useful if you have a bunch of images/scans where the same area at the top needs to be chopped. Sometimes the -trim option (such as the case of white space on top)is wrong and ends up cropping the image and losing some text. ImageMagick's convert is very useful but tricky to find some things out as I find it to be less than intuitive sometimes. Chopping off the bottom convert -crop -0-400 image.jpg image.pdf........

  • Linux Mint Ubuntu Debian How To Disable Webcam Automatically Onboot To Prevent Spying and Privacy Violations


    It is well known hackers, the NSA, CIA and other groups have created malware to secretly turn on your webcam and microphone on your phone, tv etc.. But fortunately on our computers and laptops we have some options. Most webcams use the "uvcvideo" kernel module / driver. You can disable this in two ways on boot. I recommend both just as a failsafe. Disable it on rc.local once your system boots automatically Add the followi........

  • SMF Forums / Simple Machines Forums Not Displaying Images Theme or Styles Properly using 127.0.0.1


    This is one thing that has me wondering about SMF. It is apparently a known issue but in the latest version and new install nothing looked right because it was using http://127.0.0.1 to find everything! How on earth would it ever do this or think it is normal? Excerpt of crazy html code it produces that causes the issue: ........

  • vzquota : (error) Quota on syscall for id 4532: No such file or directory vzquota on failed [3] OpenVZ Error and Solution


    Starting container... vzquota : (error) Quota on syscall for id 4532: No such file or directory vzquota on failed [3] Solution vzquota drop 4532 Then start the container and it should work. It actually happened after migrating the VPS manually to ano........

  • Apache htaccess Custom ErrorDocument not working properly for root home page 403 Error Issue and Solution


    So I have a domain "testdomain.com". Inside test domain.com's root is the following .htaccess: Options +FollowSymLinks -Indexes ErrorDocument 403 /launch/index.html Order Deny,Allow Deny From All Allow From 192.168.1.2 When you visit anything other than root things work fine. Eg. if you visit http://testdomain.com/somedirfile.html It will show the right error in /launch/........

  • How To Install Windows Server 7 8 10 12 2008 2012 2014 2016 Servers Desktops using Linux tftp, dhcpd and samba


    It has been a big pain for a long-time to install Windows from a Linux environment. I used to run a windows install server and it never worked right for some reason (the install would fail on most servers). Before getting start be sure to setup your samba share so once you boot into WinPE you can mount the install for whatever Windows you want /etc/samba/smb.conf [smbwinstall] path = /tftpboot/images/winstall guest ok = yes........

  • MySQL Cannot Update/Write to any database table solution


    This happened on Centos for no apparent reason with no obvious issue in the logs. Data could be read fine but not written (possibly due to some corruption or out of memory issue in the OpenVZ container is the best guess). All mysql update and insert queries failed freezing without any error log on any database and table. Tried to restart: service mysqld restart Timeout error occurred trying to stop MySQL........

  • htaccess apache how deny/allow to block or allow by IP address


    order deny,allow Deny From All Allow From 8.8.8.8 A simple and quick way to improve security by only allowing specific IPs to your web application. In this case the above allows only the IP 8.8.8.8 to access things and everything else is denied.........

  • Install Windows From a Linux TFTP Server instead of using WDS Solution


    yum -y install samba vi /etc/samba/smb.conf https://www.kernel.org/pub/linux/utils/boot/syslinux/syslinux-6.03.zip mkdir syslinux;cd syslinux;unzip syslinux-6.03.zip mkdir -p /tftpboot/libs/ cp bios/com32/modules/linux.c32 /tftpboot/libs/ cp bios/com32/libutil/libutil.c32 /tftpboot/libs/ cp bios/com32/lib/libcom32.c32 /tftpboot/libs/ #add lib path echo "PATH libs" >> /tftpboot/pxeli........

  • How To Secure Samba NMBD/SMBD to bind to a specific IP address


    By default Samba SMB/NMB listen on ANY and ALLIPs on your system by binding to 0.0.0.0. Obviously this is a huge security risk if you have a public facing server with both internal and external access. Usually when a system administrator sets up a samba server their intention is just to share with a LAN. To do this you need to the following options under the [global] section in smb.conf bind interfaces only = yes interfaces = 192........

  • How to disable Google Fonts in Wordpress


    edit theme css: Click "Appearance -> Editor -> Stylesheet" http://yourblog.com/wp-admin/theme-editor.php?file=style.css&theme=twentysixteen textarea { color: #1a1a1a; /*font-family: Merriweather, Georgia, serif;*/ font-family: "Lucida Sans Unicode", "Lucida Grande", sans-serif........

  • How to find and mount mdadm arrays automatically


    A great way if you have a bunch of drives and mdadm connected and are looking for backups/archives and don't know what is where! for md in `cat /proc/mdstat|grep md[0-99]|awk '{print $1}'`; do mkdir /mnt/$md; mount /dev/$md /mnt/$md; done........

  • M2Crypto.SSL.Checker.WrongHost: Peer certificate subjectAltName does not match host, expected fedora-archive.ip-connect.vn.ua, got DNS:mirror.ip-connect.vn.ua


    You are using Centos 5 which is deprecated so nothing in yum will work until you follow this post to use the vault: http://realtechtalk.com/Centos_59_Working_Vault_Repo_file-1921-articles yum update Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * epel: fedora-archive.ip-connect.vn.ua Traceback........

  • l2tp ipsec VPN Error Sep 12 18:16:25 vps pluto[7299]: ERROR: asynchronous network error report on eth0 (sport=500) for message to 192.5.6.2 port 20640, complainant 192.5.6.2: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated


    Sep 12 18:16:25 vps pluto[7299]: ERROR: asynchronous network error report on eth0 (sport=500) for message to 192.5.6.2 port 20640, complainant 192.5.6.2: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)] Some say changing the "leftprotoport=17/%any" will fix this but I have not found this to be the case. Essentially it means at least one end is blocking the ipsec packets. Sometimes the %any allows an alt........

  • ecryptfs how to mount or recover from a backup


    The easiest way to recover or mount an off-line ecryptfs directory is the built-in command from ecryptfs sudo ecryptfs-recover-private It will find your wrapped passphrase and ask for your password and mount it in tmp. Much easier especially when your current active OS is using ecryptfs too. This a fantastic tool when going through old backups.........

  • kdenlive titles/text renders as white screen when using .sh script


    When using the .sh script the rendering doesn't work after an upgrade of related packages to kdenlive. kdenlive (kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1)) with affine or composite transitions was fine but is now broken during the time of transition it is just a white screen. The previous version was fine: kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1 But now I can't find it or install it:........

  • ffmpeg trouble concatenating similar but different files


    When things go wrong your video is basically unplayable or the first video plays fine and then freezes when moving on to the next. Generally if both videos weren't produced with the exact 100% same settings you will have issues. You can try the basic concat but it often won't work right. Solution for me: My example uses 3 videos in total so "n=3" and a=1 to include audio. ffmpeg -threads 12 -i file1.mp4 -........

  • Linux Mint USB Kernel Tainted and Locked Port/Dev File


    Essentially a program I was running for mining did not terminate properly with Ctrl+C it is listed as defunct and cannot be killed, kernel is tainted and normal tricks to disable the port are impossible the dev and sys entries for the device cannot be browsed or interacted with in any form without a lockup of the request. The only solution is to reboot due to the kernel taint as far as I can find so far. [1130246.811056] INFO: task minerd:21861 blocked for more th........

  • ffmpeg Linux Mint download, compile and install howto


    #if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2 tar -jxvf ffmpeg-3.3.2.tar.bz2 cd ffmpeg-3.3.2/ ./configure --disable-yasm install prefix /usr/local source path ........

  • Migrate Centos 7 from Single HDD to mdadm RAID 10 array:


    Done on Centos 7.3 very important as clearly based on older guides it was a lot easier and more simpler! Hint do not use grub2-install! If you have trouble booting after this check this CentOS mdadm RAID booting/fixing guide. One huge caveat if you are an oldschool user or sysadmin who has avoided UEFIbooting The nor........

  • Centos 7 Cudaminer Nvidia setup guide


    I am using a GTX 1060 but replace the download for the driver with the correct/current version for your particular card by visiting: http://www.nvidia.com/Download/index.aspx?lang=en-us yum install automake curl openssl-devel libcurl-devel gcc gcc-c++ yum -y install kernel-devel-`uname -r` yum -y install unzip #the........

  • USB 3.0 PCI x1 Card Review VIA VL805 on Linux Review and Experience


    This is a VIA made VL805 USB 3.0 Chipset with 4-ports and MOLEX powered. First of all this unit was cheap at about only 9 USD with fast shipping. My biggest concern was if this was a quality unit and would it really give you full USB 3.0 speeds (some people reported with similar cards that for some weird r........

  • cudaminer freezes Linux Mint taints kernel


    When running cudaminer once it tries to initialize the card the entire screen freezes. The computer itself is still running but the Xorg is done for, you cannot even switch to another console window and must reboot (even an mdm or Xorg restart does not help). At first cudaminer will give you these errors: stratrum_recv_line failed ...retry after 15 seconds GPU #0: Geforce 210 with compute ca........

  • Nvidia Linux Mint/Ubuntu screentearing horizontal line solution


    Finally after ages I found the solution which is on many pages on the net but not obvious and should have been standard or more common info! Instant Solution: Type this into the terminal (unfortunately the driver config menu doesn't have the option as itis hidden): nvidia-settings --assign CurrentMetaMode="nvidia-auto-select +0+0 { ForceCompositionPipeline = On }" Make permanent Cli........

  • Openshot 2.2 is very unstable always crashing in Linux Mint 18.1!


    Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Missing folder chosen by user: Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Removed missing file: MAH02949.MP4 Jun 1 15:45:57 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: ui_util:WARNING Icon theme media-playback-start not found. Will use backup........

  • Apache SSL very slow response with Firefox Freezes/Loads Very slow when checking self-signed SSL certificate


    I was sure this was a Centos bug with OpenSSL, Apache, MySQL or even PHP. I tried everything but nothing helped. One clue is that if you check the Apache logs you will see nothing in the access logs until minutes later (this means Firefox has not even passed your request to the remote Apache/htttpd server). When even accepting the invalid certificate message that would show up minutes later when trying to "View the Certificate" Firefox would freeze. This bu........

  • MySQL Add multiple IPs for remote user including root howto


    To grant the IP 192.168.2.4 to user mysqlguy GRANT ALL ON *.* TO 'mysqlguy'@'192.168.2.4'; To allow any IPfor mysqlguy just use the wildcard % character GRANT ALL ON *.* TO 'mysqlguy'@'%'; Also note it is normal and fine to have multiple entries in the mysql table.........

  • Linux Mint/Ubuntu/Debian Nvidia driver becomes slow graphics performance issue


    I've had this issue since Ubuntu 9 and now even on Linux Mint 17 no matter what latest version of the Nvidia proprietary driver that I use. It just becomes slower and slower and only gets better after rebooting or restarting Xorg. Someone here has it as well https://askubuntu.com/questions/822449/graphics-becomes-slow-after-a-while/917886 It's very fru........

  • Linux Mint missing ffmpeg solution to install from Ubuntu PPA


    This is very annoying that ffmpeg is missing from Linux Mint! They have ffmpeg2theora which is a totally different codec and does not work as ffmpeg does at all (it is basically totally different). However on Linux Mint 17 I was able to use a Ubuntu PPA and sucessfully install ffmpeg! https://launchpad.net/~mc3man/+archive/ubuntu/trusty-media Adding this PPA to your system........

  • phpBB3 slow and internal dummy connection


    Using Apache 2.2 and PHP5.6 PHPBB3 is very slow to respond. Actually for some reason it takes so long to even register a log entry in access_log as in several seconds or a few minutes later it shows up in Apache. All other vhosts and Apache access stops working and freezes until the request to access PHPBB3 slowly completes. It seems to randomly be slow if you stop using it whether for posting or reading the forums. I've migrated to different machines including........

  • Avocent DSR8020 KVM/IP - Network Connect Error - Solution


    This error is commonly due to Java security or TLS settings but there is a second issue with forwarded ports that also causes it. 1. Java Security/TLS Settings issue: This article has the solution to change them all in Linux automatically 2. Port Forwarding Issue if your Avocent DSR is behind NAT/private IP........

  • Centos 7 Migration Guide from Centos 6


    Centos 7 is no cakewalk, there are many fundamental features and basic utilities that are missing or even completely renamed or different! Another shocking thing is to check your NIC it is set by default to not turn on when booting! And by the way there is no more standard eth0 the NIC convention is now "enp0s3" vi /etc/sysconfig/network-scripts/ifcfg-enp0s3........

  • ecryptfs errors


    ecryptfs-mount-private Enter your login passphrase: Inserted auth tok with sig [ee16d84] "into the user session keyring mount: No such file or directory" [ 156.118113] ecryptfs_mount: kern_path() failed [ 156.118431] Reading sb failed; rc = [-2] [ 164.233055] traps: mate-notificati[3472] trap int3 ip:7f43d7002c13 sp:7fff162c6600 error:0 [ 166.017061] ecryptfs_mount: kern_path() failed........

  • What happens when you unplug 1 or more devices from an mdadm RAID array to simulate a failure in Linux Ubuntu/Centos/Debian?


    In short the two drives in the array were /dev/sdd and /dev/sde. The kernel sees they were unplugged and have gone down as you can see below. mdadm caught the first one being unplugged /dev/sde and disabled the missing drive. However when the final drive that was part of the array is unplugged it didn't notice at all. Instead it complains about an IO error later for drives that the kernel knows do not exist anymore. [45817.162728] ata4: exception........

  • mdadm and lvm how to completely disable and remove vg/pv/lv


    In short the solution is just to use vgremove for the actual /dev/mapper device: vgremove /dev/mapper/backups-backuplv box mnt # mdadm --manage /dev/md8 --stop mdadm: Cannot get exclusive access to /dev/md8:Perhaps a running process, mounted filesystem or active volume group? box mnt # lv lvchange lvconvert lvcreate l........

  • curl: (1) Protocol "https not supported or disabled in libcurl"


    This seems to only happen from a bash script but it's not clear why it works from the terminal but not from a bash script.........

  • Centos 5 OpenSSL does not support TLS 1.2 Apache Error


    [Thu Jan 26 14:13:31 2017] [notice] caught SIGTERM, shutting down [Thu Jan 26 14:14:00 2017] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec) [Thu Jan 26 14:14:00 2017] [error] Server certificate is expired: 'Server-Cert' [Thu Jan 26 14:14:00 2017] [notice] SSL FIPS mode disabled [Thu Jan 26 14:14:07 2017] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec) [Thu Jan 26 14:14:07 2017] [error] Server certificate is expired: 'Server-Ce........

  • How to Properly Secure SSL/TLS Apache Settings against Heartbleed Poodle (TLS) Poodle (SSLv3) FREAK BEAST CRIME


    Many users still are not aware but simply patching OpenSSL does not secure you against many known and easy to exploit attacks that will render your encryption useless by an attacker. Use the following setings in /etc/httpd/conf.d/ssl.conf SSLCipherSuite "EECDH+ECDSA+AESGCM EECDH+aRSA+AESGCM EECDH+ECDSA+SHA384 EECDH+ECDSA+SHA256 EECDH+aRSA+SHA384 EECDH+aRSA+SHA256 EECDH EDH+aRSA !CAMELLIA !SEED !3DES !RC4 !aNULL !eNULL !LOW !MD5 !EXP !PSK !........

  • ioncube loader install howto on PHP/Centos


    Disclaimer, before starting this I do not like ioncube, it is great to protect your source code, but a big pain to setup this extension since it has to be done manually. Further, fi you do a PHPupdate ioncube may no longer work, causing important sites or services to not work (I wish authors would take another approach). 1.) Download from here:https://www.ioncube.com/loaders.php 2.) Extract the contents and co........

  • cPanel Install Error kernel ipv6 module support solution


    2017-01-12 14:25:36 529 (ERROR): The installer was unable to verify that your kernel supports IPv6. 2017-01-12 14:25:36 530 (ERROR): The message received when trying to create an IPv6 socket was Address already in use 2017-01-12 14:25:36 531 (ERROR): Please ensure that the ipv6 module is enabled and loaded in your kernel. 2017-01-12 14:25:36 532 (FATAL): Exiting... Solution This happened........

  • PayPal Subscription Howto Creation Automatic Payments Manual


    An easy way to pay companies and friends/family since PayPal does not have an option when sending money to make it a subscription: "business" = The e-mail or PayPal ID of the person/organization to pay to. a3 The recurring amount "eg. 115" will be 115 USD p3 The time period (eg. 2) t3 Unit of time period m=monthly,w=weekly,y=yearly item_name = "the note/product service reason you are paying ha........

  • PYCURL ERROR 22 - The requested URL returned error: 404 Not Found Solution


    # yum -y install qemu-kvm Loaded plugins: fastestmirror Setting up Install Process Loading mirror speeds from cached hostfile * base: mirror.lzu.edu.cn * elrepo: ftp.utexas.edu * epel: ftp.jaist.ac.jp * extras: mirrors.aliyun.com * openvz-kernel-rhel6: mirror.fdcservers.net * openvz-utils: mirror.fdcservers.net * updates: mirrors.nwsuaf.edu.cn Resolving Dependencies........

  • OpenVZ Solution CPT ERR: c02fa000,73 :CPT: lock fd is closed incorrectly: 1 and vps-net_add ERROR: Unable to add route ip route add 192.168.5.2 dev venet0


    The only solution after trying many suggestions was to simply restart the "vz" service (definitely not preferable). Even doing an ifdown and ifup for venet0 did not help. ifup venet0 Bringing up interface venet0: Configuring interface venet0: net.ipv4.conf.venet0.send_redirects = 0 RTNETLINK answers: Network is down Some errors from log: CPT ERR: d2dc60........

  • SELinux targeted policy relabel is required


    You may get this after a long time of not rebooting but especially if you have rsync'd a / partition or deployed an image to another VPS or computer, you will often have this issue. The good thing it usually just takes a reboot. Here is more info from Centos........

  • The connection was reset The connection to the server was reset while the page was loading.


    In Firefox I cannot connect to any website, proxy is disabled and outside network access is confirmed, no system or manual proxy was set on this Linux Mint/Ubuntu system. Normally this can be caused by proxy or DNS problems and the weird thing is that traceroute and ping to other IPs worked fine but even connecting to sites by IP was not working. The connection was reset The connection to the server was reset while the page was loading.........

  • Centos and obfsproxy install errors


    pip install obfsproxy /usr/lib/python2.6/site-packages/pip/_vendor/requests/packages/urllib3/util/ssl_.py:90: InsecurePlatformWarning: A true SSLContext object is not available. This prevents urllib3 from configuring SSL appropriately and may cause certain SSL connections to fail. For more information, see https://urllib3.readthedocs.org/en/latest/security.html#insecureplatformwarning. InsecurePlatformWarning You are using pip version 7.1.0, however version 8.1.1 i........

  • curl: (35) SSL connect error solution


    curl -k https://somesite.org curl: (35) SSL connect error The site used to work until I got a new SSL cert Updating curl with (yum -y install curl) made it work again. ........

  • How to modify HTML/Themeforest Themes to work in any path statically using unix/linux's sed command


    For themes and custom CMS setups, the typical HTML theme is not ready to go at all but here are some common sed commands (search and replace that will get most of them working without breaking as you'd expect). The problem is that often the theme directory will be separate from the content and this will break the relative paths that these themes use. sed -i s/'href="'/'href="/themes/yourtheme/'/g index.html sed -i s/'src="'/'src="/themes/y........

  • vps windows 2008 datacenter error code 0xc004c020


    Does anyone have any suggestions on how to handle this error code? It is for a client who has a Windows 2008 R2 Datacenter License and wants to install virtual instances on the same host.........

  • Nvidia Linux Card not working due to LSI 9200/SAS2008 IRQ conflict


    At first my BIOS said the card may not work right because there is no more option ROM space. I disabled the Option ROM for both LSI 1068 and 2008 chipsets, Network Boot ROM and most other PCI slots, Serial Port, etc... and the message went away but the card still does not work properly. But it still cannot initialize the card properly(does not work): [ 33.943272] NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:........

  • Linksys E2500 DD-WRT Upgrade Instructions and Enabling 5ghz with Tomato Firmware


    1.) Flash directly to this file: http://tomato.groov.pl/download/K26RT-N/build5x-132-EN/Linksys%20E-series/tomato-E2500-NVRAM60K-1.28.RT-N5x-MIPSR2-132-Max.zip *I was never able to get the larger "Mega" file to work, at least not initially so I recommend the file above. To enable 5ghz I had to do the "Clear NVRAM" Option before it was shown. 2.) Or if you don't need 5ghz (most devices do not support it and cannot........

  • Linux Mint/Ubuntu/Debian Window Controls Missing Solution


    If Linux Mint 17 or other has no window buttons/controls you can do the following from terminal: marco --replace& Sometimes it can be fixed if you go to your themes/appearance and choose a new one but in the case like mine where Compiz is installed but not running/working then that fix will not work and will require the marco command above. What if you can't type in a terminal Window? If you close........

  • Redirect www host to non-www Linux Apache modrewrite


    The below forces all request to your domain to go to the main non-www root domain. Updated code: RewriteCond %{HTTP_HOST} !=domain.com RewriteRule ^(.*)$ https://newurl.com/subdir/$1 [R=301,L] If you don't want it to go to a subdirectory: RewriteCond %{HTTP_HOST} !=domain.com RewriteRule ^(.*)$ https://newurl.com/$1 [R=301,L] Bad code: This code is bad beca........

  • Force SSL for all URLs Apache htaccess modrewrite


    The best way is as below in .htaccess using modrewrite, any request that is not SSL will be redirected to https://domain.com and the exact same URL RewriteCond %{SERVER_PORT} 80 RewriteRule ^(.*)$ https://domain.com/$1 [R=301,L]........

  • tsclient (Terminal Server RDP Client) missing in Debian, Ubuntu, Linux Mint


    This was a horrible shock after upgrading fromUbuntu 9 to Linux Mint 17 and I found that the last distro to support tsclient was Debian Squeeze. For some reason it has disappeared for a long time and the new options such as rdesktop and gnome-rdp do not have any start menu entry and just aren't done as well as tsclient. Fortunately there is a solution: tsclient surprisingly can be downloaded as a direct .deb package and it fails with some variou........

  • unfortunately lg keyboard has stopped - LG Phone Keyboard Issue


    This seems to effect many other LG phones , specifically their keyboard app and basically makes your phone unusable where you cannot use the keyboard because that message keeps popping up and the keyboard will not load. unfortunately lg keyboard has stopped solution: 1. Go to your settings and manage apps and find the LG Keyboard app: 2. Stop it from running, delete all data and clear all cache. After the above you will probably find that your........

  • Windows showing wrong drive size after resizing the VPS/image or cloning howto fix


    How to Increase The Disk and Partition Size in Windows 2022,2019,11,10,8,7 etc.. Server 1, Enter the command prompt Start -> cmd 2. Start diskpart diskpart 3. Find the drive that has the wrong size list volume 4. Select the volume (in this example we use volume 2) select volume 2 5. Extend the volume........

  • Centos 6 how to guide convert LVM non-RAID into mdadm 1/10 RAID array live without reinstalling


    Here is the scenario you or a client have a remote machine that was installed as a standard/default minimal Centos 6.x machine on a single disk with LVM for whatever reason. Often many people do not know how to install it to a RAID array so it is common to have this problem and why reinstall if you don't need to? In some cases on a remote system you can't easily reinstall without physical or KVM access. So in this case you add a second physical or disk or already ha........

  • openvz yum problem Centos 6.5 cannot find file on mirror:


    #solution Edit /etc/yum.repos.d/openvz.repo For the first two entries comment out #mirrorlist and uncomment #baseurl and then it worked openvz yum problem Centos 6.5 cannot find file on mirror: yum update Loaded plugins: fastestmirror Determining fastest mirrors * openvz-kernel-rhel6: mirrors.ustc.edu.cn * openvz-utils: mirrors.ustc.edu.cn base ........

  • Virtualbox errors on Ubuntu/Debian/Mint


    The solution was to reinstall the vbox dkms package and do a manual modprobe of the modules it makes. I never sorted out the unable to start due to the USB issue, I did have the guest additions installed but the only way to boot was to change the pointing device from USB to PS2 and then to disable the USB controller (if your pointing device is set as USB, disabling USB will not work because it will re-enable by default when it sees your pointing device is USB, this is w........

  • Installing zoneminder on Ubuntu/Debian Linux Howto


    sudo apt-get install zoneminder [sudo] password for one: Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: libuser-perl python-evince kdebase-apps kwrite unixodbc libgnomeprint2.2-data python-soappy vgabios python-metacity hddtemp python-mediaprof........

  • status: { DRDY ERR } error: { ICRC ABRT } failed command: WRITE FPDMA QUEUED MCP55 Linux Errors


    [ 2868.041375] ata1: EH in SWNCQ mode,QC:qc_active 0x40 sactive 0x40 [ 2868.041554] ata1: SWNCQ:qc_active 0x40 defer_bits 0x0 last_issue_tag 0x6 [ 2868.041556] dhfis 0x40 dmafis 0x40 sdbfis 0x20 [ 2868.041874] ata1: ATA_REG 0x41 ERR_REG 0x84 [ 2868.042013] ata1: tag : dhfis dmafis sdbfis sactive [ 2868.042163] ata1: tag 0x6: 1 1 0 1 [ 2868.042301] ata1.00: exception Emask 0x1 SAct 0x40 SErr 0x400000 action 0x6 frozen [........

  • initial Main Mode message received on 192.168.5.94:500 but no connection has been authorized with policy=PSK


    If you are getting this error from Pluto/IPSEC it is almost always due to a routing or NAT issue.........

  • HP XW9400 Motherboard In Desktop Issues


    Fortunately the format is EATX so an EATX case will work and the screw layout is standard. You will need to remove the HEX/TORX screws that are connecting the stock HP standoffs (meant to slide into an HP case). XW9400 Motherboard Issues Size: 12" x 13" Proprietary Power Connector Proprietary CPU Power Connector Proprietary Memory Power Connector Fan connectors are 4 pin so you will need some kind of adapter.........

  • Linux CLI command to rip audio CD and encode convert to MP3s


    This command rips the audio tracks to .wav files *I recommend making a new directory with the name of the audio disc first and executing everything from within that directory below. cdparanoia -B Use the lame mp3 encoder to encode each one with this script: *Note that this will encode any other files ending in "cdda.wav" for track in `ls *cdda.wav`; do lame -b 192 $track; done........

  • No response from subprocess (whostmgr (whostmgr)): The subprocess exited with status 12 (ENOMEM).


    No response from subprocess (whostmgr (whostmgr)): The subprocess exited with status 12 (ENOMEM). This happened on a client's VPS which ran out of memory.........

  • Windows 2012 Server R2 Install Error "windows cannot find the microsoft license terms windows 2012 server install"


    windows cannot find the microsoft license terms windows 2012 server install This is actually because you are using less than 576MB of RAM. In my case I was installing on a KVM VPS with 512MB of RAM. This issue would apply to any physical or virtual server with less than 576MB of RAM. This includes Virtualized VPS Servers with XENHVM, KVM, VBOX, VMWare etc.. or Dedicated Servers with such little RAM. It's very misleading of course since it has not........

  • cPanel how to force reinstall rpms and fix packages and other problems caused by updates or duplicate rpms


    If a service is not working and resetting it to defaults is not working and you get bizarre error messages it is probably a broken update and possibly duplicate package. Take in this case "exim" not working even after resetting to defaults. Check for duplicates: rpm -aq|grep exim ........

  • Dell CS24SC Server Info


    Dell CS24SC Info 0000:00:00.0 Host bridge: Intel Corporation 5100 Chipset Memory Controller Hub (rev 90) 0000:00:02.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x8 Port 2-3 (rev 90) 0000:00:03.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x4 Port 3 (rev 90) 0000:00:04.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x16 Port 4-7 (rev 90) 0000:00:05.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x4 Port 5 (rev 90)........

  • Dell CS10-F1D Server Info lspci Linux specs


    0000:00:00.0 Host bridge: Intel Corporation 5000P Chipset Memory Controller Hub (rev b1) 0000:00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 (rev b1) 0000:00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 (rev b1) 0000:00:04.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 (rev b1) 0000:00:05.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4........

  • Linux disable firmware prevents NIC/Ethernet from working phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.


    [ 17.208336] tg3 0000:08:00.0: eth0: Link is up at 1000 Mbps, full duplex [ 17.210194] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX [ 76.000065] phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware. [ 76.002332] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 86.736004] eth0: no IPv6 routers present [ 148.960038] phy0 -> rt2x00lib_request_fi........

  • OpenVZ vzctl update changes how iptables work - iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. updated solution


    Are you getting the same old error message even though your iptables settings for OpenVZ are correct? iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. The reason is because in newer vzctl the old way of setting IPTABLES="" in vz.conf is completely deprecated (I spent some time fiddling wondering why my settings were correct but........

  • esniper and curl errors https://signin.ebay.com/ws/eBayISAPI.dll?SignIn: Couldn't connect to server: couldn't connect to host


    I kept thinking it was esniper but somehow my bash settings have a preset proxy that was creating the issue. https://signin.ebay.com/ws/eBayISAPI.dll?SignIn: Couldn't connect to server: couldn't connect to host curl manually to any URL is the same: curl: (7) couldn't connect to host Run curl with -vvvvvv mode to see the issue: curl -vvvvvvvvvv http://realtechtalk.com * About to c........

  • Centos automatic ifcfg-eth0 scripts based on list of IPs from bash


    It's a basic script that reads the file "ips.txt" in the current directory and then creates a corresponding ifcfg file     #!/bin/bash GATEWAY=192.168.1.1 NETMASK=255.255.255.0 device=eth0 counter=0 for ips in `cat ips.txt`; do........

  • Vbox/Virtualbox devices grayed out for non-root user solution


    It is a permissions issue that is hard to fix. All but one USB device is greyed out. I am already a member of "vboxusers" I have already enabled and disabled USB support for the guest. I have already reinstalled the latest VBOx guest editions If running as root it all works fine Changing........

  • Samsung C410W/CLP410W not printing in Linux solution


    You need to use the Samsung driver but specify it as a CLP-360 (this is what I used for my CLP365) and incidentally most of these units look identical on the outside on inside (I've been buying whatever the latest C300 and now 400 unit for years which all seem the same with slightly different features that I never use). The solution Once again try specifying earlier models and revisions if the printer doesn't print (it will say it's been sent to the printer bu........

  • /usr/libexec/mysqld: The table 'session' is full solution


    First of all if you're getting this error it is a result of extreme database activity. If you aren't expecting it or it doesn't make sense to you 99% of the time this is a database driven script being exploited (some common examples I see often are things like phpBB being hit by dozens, hundreds or thousands of bots making constant DB write requests). The easiest way to identify this is to restart MySQL and then run the third party tool "mtop" and you'll see all........

  • Postfix how to secure outgoing authenticated e-mails for privacy and hide the IP address, mailer and other things


    The most common solution is to use the /etc/postfix/header_checks but this is a big problem. Why is header_checks a problem? Because it does it to all mail whether incoming or outgoing and whether authenticated or not. We of course want as much header information for incoming as we can get for many reasons but many organizations want to secure and make their mail clients as secure as possible. I adapted this solution to the client's custom config, they are configur........

  • PayPal subscriptions automatically cancelling after creation of profile


    There is a weird quirk with how this works, but there is a variable called "src" that defaults to 0 or disabled if not specified as 1. The default 0 means not to recur billing on a subscription.  It's too bad it's not more obvious anywhere nor is there an explanation or warning during payment or after to both the seller and buyer. Here's a proper subscription code example that does recur and does not cancel........

  • 2CO/2Checkout Howto Enable IPN/Notification Setup & Script Info


    https://www.2checkout.com/documentation/notifications/order-created It shows all the parameters that get passed so you can make a simple script to process it. To enable 2CONotifications you need to do the following: Login Browse to the top right to an icon that looks like a "circle with horizontal lines inside" - Notifications. Enter the appropriate URL for your IPN/Notification processing script (........

  • 2CO/2Checkout how to create recurring payment subscription button dynamically


    It was hard to find this as I find most online payment processors don't just put the basic information in plain view. Remember to set your sid (your seller id). The below can easily be turned into a scripted PHP template to integrate into your own custom or existing payment solution. http://help.2checkout.com/articles/How_to/How-to-Sell-Recurring-Products-with-2Checkout/........

  • CPanel Link to all of the command line options


    CPanel says you can access 98% of the functions through CLI which experienced Unix/Linux admins prefer for simplicity and for scripting.  I've never found CPanel easy to use from the admin panel, it seems everything is hard to find and a simple task becomes a series of hunts. So for people like me here's the list: http://cpanel.net/system-administrators/command-line-scrip........

  • PayPal Convert BuyNow Button to Plain HTML Link


    Say if you have a form/button like this: ........

  • mytop install errors


    mytop-1.4-2.el5.rf.noarch from rpmforge has depsolving problems --> Missing Dependency: perl(DBI) is needed by package mytop-1.4-2.el5.rf.noarch (rpmforge) solution: #disabling excludes is required on CPanel type boxes which exclude most updates including perl-DBI yum --disableexcludes=main install perl-DBI mytop-1.4-2.el5.rf.noarch from rpmforge has depsolving problems --> Missing Dependency:........

  • heatbeat ERROR: NV failure (msgfromsteam): [>>> ] ha_msg_add_nv_depth: line doesn't contain '='


    Apr 17 11:55:47 Cluster01 heartbeat: [1426]: WARN: ha_msg_add_nv_depth: line doesn't contain '=' Apr 17 11:55:47 Cluster01 heartbeat: [1426]: info: >>> Apr 17 11:55:47 Cluster01 heartbeat: [1426]: ERROR: NV failure (msgfromsteam): [>>> ] I have never been able to reproduce the above but it happened on heartbeat-3.04-2 when Itook a node down for testing. One thing Ibelieve caused it was by configuring ha.cf........

  • OpenVZ avoid vzctl 4.7 and ploop


    OpenVZ has made vzctl version 4.7 default to using ploop which is a big annoyance.  No one wants it otherwise we'd use Xen or KVM. Make sure to manually specify vzctl 4.6.1 or you will have issues with old scripts breaking since it defaults to using ploop (a single image like Xen/KVM). Here's a list to old versions of vzctl.........

  • virtio KVM drivers download location


    http://realtechtalk.com/downloads/virtio-win-0.1-74.iso Current Direct stable URL from Fedora: https://fedoraproject.org/wiki/Windows_Virtio_Drivers Direct Downoad of Stable Virtio: https://fedorap........

  • mencoder howto trim split edit time of mp4 from Samsung Note


    mencoder -fps 30 -ss 00:00:38 -oac lavc -ovc copy 152408.mp4 -o soundedit.mp4 The -ss flag means to start at 38 seconds (so the first 38 seconds of video will be removed).........

  • yum Centos 386 and 64 bit conflict resolution


    This can happen when you install RPMForge or other repos with the wrong architecture and here's how you fix it (simply uninstalling won't usually fix it): solution yum clean all yum -y install openvpn Loaded plugins: fastestmirror, presto Loading mirror speeds from cached hostfile * base: mirror.its.sfu.ca * extras: centos.mirror.nexicom.net * rpmforge: mirror.cpsc.ucalgary.ca * up........

  • Centos Howto Upgrade to PHP 5.3 from 5.2


    It's not as simple as "yum install" as you can see below and it doesn't stop there. yum install php53 Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * rpmforge: mirror.us.leaseweb.net * extras: centos.mirror.rafal.ca * updates: centos.mirror.nexicom.net * base: centos.mirror.nexicom.net * addons: centos.mirror.nexicom.net Setting up Install Process........

  • cPanel VPS Server Cannot Login as root


    I was worried the server was hacked, I was logged in already as root but couldn't login to CPanel or a new SSHsession. I even reset the password from the shell and it did not work still. The reason is CPanel Hulk, it detected a brute-force attack so it locked down the root account entirely even from the correct password. According to cPanel the best way around this is to whitelist your IP.........

  • Howto edit/rotate Samsung/Android Videos in mencoder solution


    Movie-Aspect is undefined - no prescaling applied. videocodec: libavcodec (720x1280 fourcc=34504d46 [FMP4]) [mpeg4 @ 0x2c91c00] timebase not supported by mpeg 4 standard Could not open codec. FATAL: Cannot initialize video driver. That is the error I would get, I thought it was a codec error something else. By fluke Isaw something about ffmpeg where someone recommended manually telling it to the "fps" and it worked.........

  • SSH HowTo Create Port Forwards


    ssh -L 5905:localhost:5900 root@yourserver.com The "-L" means to create a port forward to a port on your server. The 5905 means the port on your computer that will be used to access the port 5900 on the remote server. localhost is the IP that you use to access the port forward (you can change it to 0.0.0.0 which will be all IPs on your system/computer but localhost is good for security and privacy unless a whole network of people need access).........

  • What a hdd hard drive and mdadm RAID array failure looks like in Linux


    [3805108.257042] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [3805108.257052] sd 0:0:0:0: [sda] Write Protect is off [3805108.257054] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [3805108.257066] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [3805108.257083] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB) [3805108.257090] sd 0:0:0:0: [sda] Write Protect is off........

  • cPanel Find/Set Main DNS Servers for Template Howto


    Go to: "Server Configuration" -> Basic cPanel & WHM Setup Scroll to: "Nameservers" (at the bottom) From there you can set the names of the nameserver and their IPs. It's very weird and confusing that nothing under IP Functions/DNS has or links to this.........

  • Asterisk iptables block bruteforce attacks howto with fail2ban


    yum -y install fail2ban vi /etc/fail2ban/jail.conf [asterisk-tcp] enabled = true filter = asterisk action = iptables-multiport[name=asterisk-tcp, port="5060,5061", protocol=tcp] sendmail-whois[name=Asterisk, dest=you@example.com, sender=fail2ban@example.com] logpath = /var/log/asterisk/messages maxret........

  • htaccess allow only certain IPs howto


    order deny,allow deny from all allow from your.ip.here ........

  • Dell CS24-NV7 Howto Enable LAN/NICs and PXEBoot in the BIOS


    Dell CS24-NV7 Unusually the Virtualization was enabled when I got this server but all the NICs were diabled in the BIOS including PXE boot! Advanced -> Advanced Chipset Control PCI Slot 1 Option ROM: Enabled Onboard LAN1 Control: Enabled LAN1 Option ROM Scan: Enabled (you need it for PXE boot) Onboard LAN2 Control: Enabled LAN2 Option ROM Scan: Enabled *you will need to reboot and........

  • proxychains error solution ERROR: ld.so: object 'libproxychains.so' from LD_PRELOAD cannot be preloaded: ignored.


    Get the new version here that actually works: https://github.com/haad/proxychains........

  • Linux find what processes are swapping


    Here is a handy script that will check all processes and report what is swapping #!/bin/bash for pid in `ps x|awk '{print $1}'`; do result=`cat /proc/$pid/status|grep VmSwap|awk '{print $2}'|grep -v ^"0"` if [ ! -z "$result" ]; then programresult=`ps x|grep $pid|grep -v grep` if [ $? == 0 ]; then program=`echo $programresult|awk '{print $5}'|grep -v ^grep`........

  • Apache SNI is not needed what is the issue?


    Iread this article and still don't understand the issue. If I understand correctly the client negotiates after the first SSLconnection and then gets the correct hostname and thus correct certificate. http://wiki.apache.org/httpd/NameBasedSSLVHostsWithSNI To their credit I know I'm not using SNIbecuase Iget this message in the Apache log :) [warn] Init: You should not use name-based virtual hosts in conjunction with SSL!! B........

  • Centos 5,6,7 Install EPEL from Fedora for extra packages Howto


    http://fedoraproject.org/wiki/EPEL#How_can_I_use_these_extra_packages.3F Visit the above URL, choose your version and architecture and install it. EPELhas a lot of missing and extra packages that rpmforge does not. For old versions of EPEL that are deprecated, eg.........

  • CPanel suhosin install failed


    /scripts/phpextensionmgr install PHPSuHosin Updating md5sum list Fetching http://httpupdate.cpanel.net/cpanelsync/easy/targz.yaml (connected:0).......(request attempt 1/12)...Resolving httpupdate.cpanel.net...(resolve attempt 1/65)... Fetching http://httpupdate.cpanel.net/mirror_addr_list (connected:0).......(request attempt 1/3)......connecting to 74.50.120.123...@74.50.120.123......connected......receiving...100%......request success......Done........

  • htaccess block IPs while RewriteEngine/modrewrite is enabled solution


    Istruggled with this for awhile because the normal setup won't work if modrewrite is being used: ORDER ALLOW, DENY So the solution is something like this: order allow,deny deny from 12.43.12.0/24 allow from all ........

  • Sendmail Gmail.com blocking


    relay=alt4.gmail-smtp-in.l.google.com. [74.125.136.26], dsn=4.0.0, stat=Deferred: 421-4.7.0 [ 10] Our system has detected an unusual rate of This is strange because the mail server IP is not blacklisted anywhere and the IP itself has not been used for years and this server is clean and has only sent a few e-mails to gmail.com in its entire time. I wonder if this is a legacy block on a whole range of IPs as punishment for others in the block........

  • Dell FS12-NV7 2U Server Information and Guide


    I've got one of these for testing projects from work at home and got more than I bargained for with the time I've spent on it due to the storage handing/Perc 6/i cards. My particular model came with the following: 2U Rack Mount Server with Rails 2xOpteron 2373 EE (Quad Core, there is a 6-core version that can be found at times) 16GB RAM 2 x 250GB Seagate SATA 2 x Dell Perc 6/i (horrible and a nightmare to work........

  • Dell Perc 6/i Restore BIOS/Bricked Solution Guide Howto


    I bricked one of my cards by following a guide from UNRAID. Step #1 from them wipes out the BIOS, but guess what? The step where you restore the BIOS should have been done first, which is sas2flash but no version supports or is able to find my Perc 6/i. So now I'm a bit stuck. I tried using megarec but it's funny that it can wipe the BIOS but can't forcefully reload it: megarec -writesbr 0 mpt2sas.rom Supports 1078 control........

  • Dell Perci 6/i Firmware Upgrade Guide Tutorial


    One thing to remember is that you need MegaCli to do the flashing. You also need the correct file,I tried at least 2 different Perc 6 firmwares from Dell that kept getting rejected as corrupt by MegaCli(they were really the wrong version). I have an external PCI-E Dell 6 Perc/I butI chose images from the 'Integrated" on motherboard version as it was allI could find. They are different, and below is my first time finding success.........

  • Dell Perc 6/i cannot downgrade


    I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally. I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN --2013-08-26 12:53:39-- http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN Resolvi........

  • LSI MegaRAID Adventures, Guide and HowTo


    LSi Megaraid At first it was configured as a RAID 0, then I deleted the Virtual Disk Group. I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing. To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........

  • pxe-32 tftp open timeout


    pxe-32 tftp open timeout The solution was to enable tftp in xinetd with "chkconfig tftp on". See the troubleshooting below: chkconfig --list NetworkManager 0:off 1:off 2:off 3:off 4:off 5:off 6:off acpid 0:off&n........

  • CPanel domain not working properly: http://vps.thedomain.com/domainnotknown.html Solution


    The Cause Basically it's usually because your Cpanel has new IPs and the old IPs it knows are no longer available/working/valid. The solution is to change the site's IP but you may run into issues for various reasons. Here is what I encountered below. It redirects there even though public_html is empty and doesn't have any index or htaccess redirect. --- This issue happened after a CPanel migration, the site is bein........

  • yum update error


    yum update error Traceback (most recent call last): File "/usr/bin/yum", line 29, in ? yummain.user_main(sys.argv[1:], exit_code=True) File "/usr/share/yum-cli/yummain.py", line 229, in user_main errcode = main(args) File "/usr/share/yum-cli/yummain.py", line 145, in main (result, resultmsgs) = base.buildTransaction() &nbs........

  • charat in PHP convert non-English characters into code


    This is basically URL decoding to the decimal code but nothing in PHPworks how you'd expect it. Here are online tools to verify and check your work, it's important when querying databases with non-English characters: http://yehg.net/encoding/index.php# http://meyerweb.com/eric/tools/dencoder/ http://www.codetable.net/decimal/65398 Japanese: http://symbolcodes.tlt.psu.edu/bylanguage/japanesechartkatakana.html Charat code for PHP:........

  • open /dev/kvm: No such file or directory failed to initialize KVM: Operation not permitted - Solution


    open /dev/kvm: No such file or directory failed to initialize KVM: Operation not permitted [ 96.084502] kvm: disabled by bios Any of the above means that "Virtualization" is not enabled in your BIOS. Most servers and Desktops (non-mainstream) can do this no problem but leave it off by default. Note that some systems even though the CPU supports it, don't allow enabling of Virtualization for some reason (especially some lap........

  • mkdir(): Too Many Links - The Solution and Problem in ext3 filesystems


    The error itself "mkdir(): Too Many Links" is not very useful, but I'll translate it into plain English. It means you've reached the filesystem's limit of how many directories can be created in a single directory. In this case for ext3 the limit is 32000 and it was exceeded. What's the solution? The simple solution is to move those directories into more subdirectories possibly sorting them by date, alphabet or numerically.........

  • iptables redirect ports to a different host and port + NAT Masquerade howto/solution


    This is important if you need public access to internal IPs such as at your office and don't want to use a VPN just to SSHinto different servers: Below forwards the port "10001" to the IP192.200.5.53 on port 22 (of course adjust it to your needs). iptables -t nat -A PREROUTING -p tcp --dport 10001 -j DNAT --to-destination 192.200.5.53:22 Remember to enable MASQUERADE on your NAT IPs or they won't be able to talk to the outside world (........

  • css custom table class howto


    table.custom { border-collapse: collapse; border-style: solid; border-width: 1px; border-color: black; font-size: 11px; } table.custom td { border-collapse: collapse; border-style: solid; border-color: black; &........

  • WD 20EARX Dead Again


    Another new drive bad from the start: Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC } Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........

  • Asterisk DOS attack - failed for '173.242.117.192' - Peer is not supposed to register [May 23 15:46:07] ERROR[32748]: chan_sip.c:13158 register_verify: Peer '153' is trying to register, but not configured as host=dynamic


    This happened to a customer Asterisk server and it somehow found the ID of the registration account to the upstream SIP server and was railing connection attempts (it filled up the console and there were literally thousands per second). Basically this caused all incoming and outgoing calls to fail. It was a temporary fix but the solution was to block that specific IP, it's hard to stop it 100% because the customer needs the default SIP port.........

  • Powersupply Issue, Motherboard AHCI issue?


    This is the most I can get when plugging in a hard drive hot and only on some power connectors. [71656.314271] ata5: exception Emask 0x50 SAct 0x0 SErr 0x90a02 action 0xe frozen [71656.314277] ata5: irq_stat 0x00400000, PHY RDY changed [71656.314285] ata5: SError: { RecovComm Persist HostInt PHYRdyChg 10B8B } [71656.314294] ata5: hard resetting link [71660.360686] ata5: softreset failed (device not ready) [71660.360694] ata5: applying........

  • mysqldump: Couldn't execute 'show create table `general_log`': SHOW command denied to user 'user'@'localhost' for table 'general_log' (1142) - Solution


    mysqldump: Couldn't execute 'show create table `general_log`': SHOW command denied to user 'user'@'localhost' for table 'general_log' (1142) One of my clients almost found out the hard way, here is an unlikely situation that happened. 1.) Years ago the client had another VPS to which they backed up a BLOG nightly to an .sql file, what they forgot is that the file also contained all databases (they used the --all-databases option but forgot). So imagi........

  • PHP How To Create and Assign Variables from POST/Submit FORM


    foreach ($_POST as $key => $value) { if ( $key != submit ) { $values.="$key=$value<........

  • SSH Can't Login/Hang


    Client Log OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to 192.168.1.253 [192.168.1.253] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type 1 debug1: identity file /root/.ssh/id_d........

  • Directadmin error/** Found 7 pre-existing rpmdb problem(s), 'yum check' output follows: e2fsprogs-devel-1.41.12-3.el6.i686 has missing requires of e2fsprogs-libs = ('0', '1.41.12', '3.el6') e2fsprogs-devel-1.41.12-3.el6.i686 has missing requires of l


    Solution To The Following: yum -y install zlib-devel yum -y install e2fsprogs* *** Cannot find /usr/include/et/com_err.h. (yum install libcom_err-devel) *** Installation didn't pass, halting install. Once requirements are met, run the following to continue the install: cd /usr/local/directadmin/scripts ./install.sh Common pre-install commands: http://help.directadmin.com/it........

  • Toshiba Hard Drive Warranty RMA Serial Number Info


    Here's the link to the warranty checker and from there you can also create an RMA: https://myapps.taec.toshiba.com/myapps/admin/jsp/webrma/addRequest1NoLogin.jsp Note that the serial# shown in SMART is not complete as is the case for many other brand sof HDDs. For example a 2TB Toshiba shows the following Serial Number in SMART: Device Model:........

  • Bad Hard Drive Slows Down Computer


    Here's a proven example of what a bad hard drive can do, it was technically functioning OKin a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application. The truth is that this failing 1TBHitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..). After swapping it out, tabs change instantly, emails are not lagged, and........

  • How to log all PHP based E-mails for abuse


    Step #1 - Create Wrapper Script vi /usr/local/bin/phpsendmail #!/usr/bin/php ........

  • Centos 6 RTL8111/8168B r8169 link up and down error solution/fix


    02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) For whatever reason it seems the r8169 driver that ships and has shipped with most Linux distros for years is still flawed and does not work properly on these cards, causing 100mbit connectivity when it should be 1gbit and even worse, causing random network dropouts. The r8169 driver in Linux kernels is simply not meant to be used on th........

  • OpenVZ - how to manually restore a VPS from another host or backup


    There are 3 pieces that are required to restore and make it work (of course consider if any kernel modules need to re-enabled and if you need to change the IPs): Copy the vz/private/VEID directory to /vz/private Copy the /etc/vz/conf/VEID.conf to /etc/vz/conf/ mkdir /vz/root/VEID After that you should be able to see the VE in vzlist -a You should then be able to start it normally.........

  • KVM support Ubuntu 12.04 or 12.10


    This seems to be a verified bug on KVM with no solution. I wasn't able to get through the installer with Ubuntu 12.04, it would crash while "configuring apt". I was able to install it with Ubuntu 12.10 but it crashes randomly at times. This happens with the latest Centos 6.3 kernel and KVM package, I even compiled the latest version from the KVM website and used that, but the results are still the same. Here's some links to discussion about the bugs:........

  • How to install GRUB to the MBR of a disk image.


    cat | grub --device-map=/dev/null Now pay close to the attention of the beginning. Type: "device (hd0) VPS.img" this is telling what hd0 will be to GRUB and we're telling it the disk image file "VPS.img" in the current directory is hd0, you can specify alternate paths and image names of course. GNU GRUB version 0.97 (640K lower / 3072K upper memory) [ Minimal BASH-li........

  • kvm cannot boot xen guest using lvm


    This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel. I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk. I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one). This is strange but it seems like this Xen PV guest has some sort of hidden or........

  • Lantronix KVM/IP Keyboard/Mouse not working in BIOS before booting the OS


    I've run into two issues with Lantronix based KVMs on various servers and here's how I solved them (with that said I like these units as they are Java based and OS independent and work very well, unike some other models like Startech). 1.) If you are connected by USB only and you're sure USB support from the BIOS is enabled, you just need to click the following in Lantronix Interfaces -> Keyboard/Mouse Check "Force USB Full Speed Mode", this fixed the issu........

  • Setup PXE Boot using Centos and dhcpd, tftp and syslinux


    This is something I often setup for clients because it's very helpful for people in datacenters, this allows custom OS installs on demand, you can customize it more by using kickstart etc.. but here's a base I use before customizing more: This little script below will install everything you need to get booting by PXE Linux. It also assumes you set a local IP (be sure not to overwrite your existing IP) on eth0:0 (note the :0) as 192.168.1.10 and it........

  • mdadm: /dev/sdb1 not large enough to join array solution


    mdadm --manage /dev/md1 --add /dev/sdb1 mdadm: metadata format 00.90 unknown, ignored. mdadm: metadata format 00.90 unknown, ignored. mdadm: metadata format 00.90 unknown, ignored. mdadm: /dev/sdb1 not large enough to join array md1's first primary member /dev/sda3 has 57394 cylinders while the /dev/sdb1 has 57393 (1 less cylinder) which is why it won't work. fdisk -l /dev/sda3 Disk /dev/sda3: 47........

  • postfix how to send to multiple recipients default limit of 1000


    The size of the message you are trying to send exceeds a temporary size limit of the server. The message was not sent; try to reduce the message size or wait some time and try again. The server responded: 4.5.3 Error: too many recipients. We set this in main.cf: smtpd_client_recipient_rate_limit=0 We didn't specify it before and the default is said to be 0/unlimited and it still didn't change anything.........

  • Linux/Centos how to block SSH bruteforce/dictionary attacks automatically with denyhosts


    A lot of people become nervous (and understandably so) when checking their auth or security logs, in Centos /var/log/secure and see dozens, hundreds of even thousands of attempted logins to various services, especially SSH. Of course you could manually block these people/IPs but no one has time to read the logs like that, what if some program or script could do it for you? This is what denyhosts does for you, it checks the logs and based on a certain number of failed SSH attem........

  • Samsung Galaxy Note Upgrade to ICS 4.0 microSDHC card not detected/dataloss after upgrading - possible solutions


    I backed up everything in the /mnt/sd_card directory thinking that some dataloss could occur for some reason but purposely left my microSDHC unbacked up thinking that "it won't touch that since it's external" and Samsung's and other manufacturers website even say this (that it won't be affected and not to worry etc). Apparently I was wrong, my microSD was "undetected" and asked to be formatted after the upgrade (there goes 3-months worth of family photos). No........

  • Centos how to upgrade from PHP 5.2 to 5.3 without downtime


    This may sound silly but there will be conflicts/issues with the default Centos repository so you have to use a third party like remi (I prefer not to do this but it's the only option unless you migrate your sites/data to another server or can stand some downtime-not an option IMHOon a production server). You may need to upgrade to PHP5.3 to run Joomla or many other reasons. Your host needs to use PHP 5.2.4 or higher to run this version of Jo........

  • ntpd[7047]: can't open /var/lib/ntp/drift.TEMP: Permission denied solution


    ntpd[7047]: can't open /var/lib/ntp/drift.TEMP: Permission denied chown ntp.ntp /var/lib/ntp/ The solution is shown above and changes the ownership to ntp.ntp which is what the ntpd daemon/server is running as. This is based on Centos but the same idea will apply on any other OS. You can do a "ps aux|grep ntpd" to see what it is running as in the case it's running as a different user. After that this annoying message wil........

  • MySQL Authentication fails after Upgrade to Version 5.5


    ERROR 1045 (28000): Access denied for user 'contentmanager'@'localhost' (using password: YES) For fun I thought I'd reset the password: GRANT ALL ON thecontent.* TO contentmanager IDENTIFIED by 'dfdfsdfdsfsdfsd'; ERROR 1470 (HY000): String 'contentmanager' is too long for user name (should be no longer than 16) This is ridiculous that this new version has some bizarre 16 character username limit and not only that but i........

  • Directadmin Enable SSL


    It's really silly how DA doesn't enable SSL by default but is otherwise a stable, fast and secure control panel. Here's a copy and paste way of enabling SSL for Directadmin in just a few seconds: *setup SSL openssl req -x509 -newkey rsa:1024 -keyout /usr/local/directadmin/conf/cakey.pem -out /usr/local/directadmin/conf/cacert.pem -days 9999 -nodes That creates the public certificate and private key pair in the location Directadmin expects to fi........

  • How To Install CPanel


    wget -N http://httpupdate.cpanel.net/latest;sh latest That one command above will do it all (and it takes a long time to install/compile). After that you can access CPanel with your root login information by visiting https://yourdomain-or-ip.com:2087 I personally don't like CPanel (bloated, full of bugs, no shared SSL, difficult to use etc..)but I admit it's easier to install than........

  • LOG: MAIN PANIC failed to expand condition "${if eq {$authenticated_id}{}{0}{${if eq {$sender_address}{$local_part@$domain}{0}{${if match{$received_protocol}{N^e?smtps?a$N}{${perl{checkbx_autowhitelist}{$authenticated_id}}}{${if eq{$received_prot


    I experienced this with CPanel's Exim after an auto-update (a Google of this error produces lots of complaints with few clear solutions). In this case I'll put the solution at the top. Run /scripts/buildeximconf to rebuild the Exim config and it should be fine after that. mail -vs "from test" user@dest.com < .bash_history LOG: MAIN cwd=/root 4 args: send-mail -i -v user@dest.com LOG: MAIN &........

  • Firefox 11 stop hiding http:// and https:// solution fix


    In Firefox type "about:config" in the address bar. Search for "browser.urlbar.trimURLs;false" and set it to true, then you'll have the http:// and https:// back. Firefox talks about the greater good but unless they don't care about security why would they hide if the url is secure or not?........

  • The Importance of a High Quality Power Supply/Power Supplies To Prevent Overheating/System Crash/Hardware Damage


    For years I've always built cheap systems believing that there is little difference in more expensive components when it comes to reliability and quality, I generally believe this still except for Power Supplies. I've always bought cheap cases with nice sounding 350-550W stock/cheap/crap power supplies and haven't had any issues for the most part until recently. One such case is an NGEAR case with a 550W Optimax power supply, I always read that these supplies don't produce the........

  • Linux Ubuntu Nvidia GT430 Lockups/Errors/Freezes NVRM: os_schedule: Attempted to yield the CPU while in atomic or interrupt context


    I'm running Ubuntu 10.10 with Asus NVIDIA GT430 2.6.35-32-generic-pae #65-Ubuntu SMP Tue Jan 24 14:06:16 UTC 2012 i686 GNU/Linux Nvidia binary driver: 260.19.06 The screen sometimes completely freezes and locks up or everything starts going very slow: [1903398.100007] NVRM: os_schedule: Attempted to yield the CPU while in atomic or interrupt context [1903402.373210] NVRM: Xid (0001:00): 53, CMDre 00000000 00000080 00000000 00000005 00........

  • KVM QEMU and Xen how to mount disk images off-line and access data


    fdisk -lu VPS.img last_lba(): I don't know how to handle files with mode 81ed You must set cylinders. You can do this from the extra functions menu. Disk VPS.img: 0 MB, 0 bytes 255 heads, 63 sectors/track, 0 cylinders, total 0 sectors Units = sectors of 1 * 512 = 512 bytes Device Boot Start End ........

  • Xen non-HVM container won't work/boot anymore


    One of my test Centos 5 containers was on a partition that filled up and it threw all sorts of errors and stopped responding but now I can't boot it again anymore. All the console shows is the Linux Penguin on the top left corner and the xm console says "usbcore: registered new driver hub" and has halted there. Centos 5 Xen container stuck/frozen won't boot on "usbcore: registered new driver hub" Another great way of troubleshooting is booting fro........

  • File /etc/vz/conf/ve-vps.basic.conf-sample not found: No such file or directory - Openvz Error solution


    Stuff like this always happens/breaks after a vzctl update, whether it's new parameters being added or required etc.. File /etc/vz/conf/ve-vps.basic.conf-sample not found: No such file or directory Fix the value of CONFIGFILE in /etc/vz/vz.conf Creation of container private area failed Warning: distribution not specified in CT config, using defaults from /etc/vz/dists/default WARNING: /etc/vz/conf/4400.conf not found: No such file or directory........

  • What's Needed To Fix Linux


    I really am a Linux fan but my comments here may not show it. Although I'm quite familiar with Linux CLI to administer servers, I find Linux GUI OS's like Ubuntu at times very clunky. This is partially because there's no such thing as a "self-made" Linux from scratch where the UIwas designed by a single team. Linux is made up of several different projects that are generally completely separate and this lack of integratiion is a key issue that makes things f........

  • OpenVPN don't use bridgestart.sh or bridge at all use iptables


    I used the suggested script to bridge from OpenVPN and it took my client's server off-line! Don't ever use their "sample" scripts if you don't have another way of accessing the server than SSH. I actually found it easier to use iptables to tell it to route IPs based on a certain subnet to route through eth0: iptables -t nat -A POSTROUTING -s 192.168.200.0/24 -o eth0 -j MASQUERADE Replace "192.168.200.0/24" with your subnet of cour........

  • postfix lopback error solution


    This is the mail system at host mail.postmail.com. I'm sorry to have to inform you that your message could not be delivered to one or more recipients. It's attached below. For further assistance, please send mail to If you do so, please include this problem report. You can delete your own text from the attached returned message. &........

  • Openvz Container IP not working suddenly Solution


    This may not apply to everyone but here is what happened to me. One day my IP connectivity for one container went dead, I could ping the hostnode from it and the hostnode could ping it but there was no external routing. I restarted the network service but it didn't help. I checked the routing table inside the VPS and the host and everything looked normal. Iadded another different IPon the same subnet to the container and it worked. Right away I st........

  • Linux Out of Memory OOM Object Killer Solution "Out of memory: kill process 1955 (sshd) score 81 or a child"


    I had a system running a 128MB live CD image with 2.8 gigs of available RAM and the OOM kernel killer went crazy when using dd for more than 8 minutes and kept killing everything. I've read that this is due to a low-memory issue and paging in the kernel and 32-bit systems with lots of RAM. I even enabled swapspace on my LiveCD and the issue happened 25 minutes into dd rather than 8 minutes, so what gives? Also no swap space was ever used! cat /proc/s........

  • How To Test If Your Hard Drive Is Good/Signs of dying hard drive


    I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem: We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........

  • Openvz YUM Error Solution to "[Errno -1] Metadata file does not match checksum Trying other mirror."


    It's weird because I have a nearly identical box and setup and I can update the ovzkernel-PAE* just fine but on this box it doesn't work. I only get this error with the openvz.repo and not others such as Centos-Base.repo With my other server it works normally: ================ Setting up Update Process Resolving Dependencies --> Running transaction check ---> Package ovzkernel-PAE.i686 0:2.6.18-238.12.1.el5.0........

  • Hitachi 2TB HDS5C3020ALA632 drive DOA


    I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead): ata1: link is slow to respond, please be patient (ready=0) ata1: softreset failed (device not ready) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1: link online but device misclassified, retrying ata1: link is slow to respond, please be patient (ready=0) ata1: softreset f........

  • Kernel/make compilation time and how to improve compile times/compile the Linux kernel faster without hardware upgrades


    I thought only a faster CPUand SSDwould help but I already have a Quad-Core CPU and it wasn't being maxed out. The actual tests were performed on an AMD-V enabled 128MB dual core VMWare container though. There is a flag that can be passed to make in order to start multiple threads, by specifying 4 threads I was able to reduce the whole kernel compilation time from scratch by about 50%! (65minutes vs 31minutes!). *Yes I did do a make clean before each co........

  • List of Free Public DNS Servers IP Addresses


    One thing to note about DNS servers and providers is that they aren't always trustworthy, not even if they're Google or your favorite ISP. Any DNS server can compromise your privacy, and they are likely tracking your browsing habits and keeping logs of it. Sometimes it's for Marketing/Research purposes such as Google's GMail service which they admit is scraped/datamined. I would expect nothing less from their DNS service. The other danger with such widely used and pu........

  • Virtualbox Guest Hang/Freeze Ghost Zombie VM Machine Problem/Solution


    Virtualbox hang problem A VM just froze and wouldn't close so I had to force it, but the VBox GUI thinks it's running even when I close it. I manually killed the related process by doing ps aux|grep VirtualBox and found the PID 6191 I killed it with "kill -kill 6191" but it remains open and as "defunct" so I can't restart it because the GUI freezes when I click on it because it thinks it is running still........

  • Apache High CPU Usage Enable Mod_Status Guide Solution - Find Cause of High CPU Usage Script/Domain


    mod_status is a great way to track down the source of high CPU usage and to find what vhost/script is the cause of it. It gives you a live view of bandwith usage, CPU usage, and memory usage broken down by domain/vhost and script/URI. Enable mod_status vi /etc/httpd/conf/httpd.conf ExtendedStatus On SetHandler server-status Order Deny,Allow Deny from all All........

  • monit example tutorial how to enable status checking and manipulation


    You need to enable the httpd daemon with monit to actually view the status and control, it's not only for the web interface since the httpd is theONLY way of controlling monit and viewing the status. monit monitor all will also reinstate disabled services if they've timed out too much. Just restarting the service will do nothing to re-monitor a service that monit has stopped monitoring due to too many failures. *Also note that /etc/monit.conf i........

  • 2011 Best Laptop - HP 15.6" Laptop featuring AMD Athlon II P340 Processor (G62-420CA)


    My mother needed a new laptop and I recommended her the same one I would have bought myself or my wife, that means the cheapest possible laptop with the most features for the money. This HP shines at this price point and one thing that made me stay away from buying more and recommending HP/Compaq was the poor battery life. Not anymore, this model has an industry leading up to 4 hours of battery life. Key Factors for Choosing It: HDMI Out........

  • Yahoo Mail (email) DNS Server Out Of Date Problems


    I don't expect this to be solved soon but some of Yahoo's DNS servers are out of whack. I changed the IPs of some nameservers of some domains and now most Yahoo users can't e-mail to those domains! As you can see below by the "No MX or A records for mychangedomain.com", now Yahoo's DNS/mailserver DNS cache is wrong. You would think they would at least have cached the old incorrect records, but instead for some reason their DNS cache has no entry and doesn't seem........

  • Virpus Review/Scam/Complaint


    Virpus Review/Scam/Complaint Virpus is advertised on LEB (lowendbox.com). My initial payment was refunded after days of not receiving the VPS, but two subscrption payments went through and Ionly received notification after the second one. They ignored the requests in the ticket and by e-mail for a refund and even escalated the PayPal dispute that "we're assuming this is for a service that was provided" (when they obviously know otherwise by........

  • 95th Percentile Billing vs Usage Billing, what's better?


    There are all kinds of threads and links on the internet, and this seems to be a contentious issue butI don't know why. 95th percentile is either a good deal for some or a big rip off for others, Ijust said it there :) But the reality is that for MOST people who transfer low amounts of data but burst to higher speeds such as 40mbit+ even for short periods of time, then you'll pay a lot of money to do that. Basically 95th percentile is an-old archaic method........

  • VPS Server Scam/Review/Complaint List


    These are the only two I've encountered but here is the low-end and note my story is not at all unique. In my case I was scammed out of money and did not receive any service at all from either company. Santrex Review/Scam/Complaint Santrex never provided any working server, I believe it was just a dummy management Solus server because the server said it was booted but never connected to the console. I complained to them and eventually the support adm........

  • Enable SPAMASSASSIN on Postfix in 5 minutes


    Centos 5 Postfix and SPAMASSASSIN Tutorial yum install spamassassin chkconfig spamassassin on vi /etc/mail/spamassassin/local.cf ############## #required_hits 5 #report_safe 0 #rewrite_header Subject [SPAM] #5 is the least restrictive (means only the most obvious SPAM is caught. 0 is obviously the most restrictive/sensitive and would have lots of false positives require........

  • Plesk Get List of E-mail Users & Aliases


    When migrating away from Plesk I couldn't figure out an easy way to get a straight list of all e-mails, but here is where I found the solution: http://nakuls77.wordpress.com/2008/08/30/details-of-email-ftp-database-users-from-psa-database/ mysql> SELECT mail.mail_name, accounts.password, domains.name FROM mail, accounts, domains WHERE domains.id=mail.dom_id AND mail.account_id=accounts.id; mysql> SELECT CONCAT(mail.mail_name,’@’,domains.name) AS Em........

  • sshfs cannot unmount error: device is busy. (In some cases useful info about processes that use the device is found by lsof(8) or fuser(1))


    umount: /home/diret/mount: device is busy. (In some cases useful info about processes that use the device is found by lsof(8) or fuser(1)) I tried everything (fusermount -u) to unmount it but the only thing that worked was actually doing this: ps aux|grep sshfs Then I identified the sshfs connection and did: kill -kill pid........

  • MySQL NEVER delete ib_logfile0 or ibdata1 or you'll lose data


    don't delete /var/lib/mysql/ib_logfile0 or ibdata1 or mysql won't restart I didn't realize they were internal and not part of replication like the relay files! /usr/libexec/mysqld: ready for connections. Version: '4.1.22-log' socket: '/var/lib/mysql/mysql.sock' port: 3306 Source distribution 110127 16:31:00 [Note] /usr/libexec/mysqld: Normal shutdown 110127 16:31:00 InnoDB: Starting shutdown...........

  • email server messsages rejected without reverse DNS DNS check failure Client host rejected: cannot find your reverse hostname Cannot resolve PTR record


    Basically you should always be 100% sure that whatever IPyour mail server sends out with has reverse DNS/PTR records. Remember that unless you own your IPs then you won't be able to set your own reverse DNS. Even if you were to create a reverse PTR record on your DNS servers it will be ignored. Reverse DNS is queried to pre-assigned DNS servers of your ISP, so therefore you'll need to contact your ISP/Colo/Hosting provider to do a reverse DNS entry. If you don't have........

  • MySQL Replication/Dual-Master vs Clustering


    Many people aren't aware but recently Dual-Master Replication setups have become increasingly popular. That's because you get similar features and benefits of having a full-blown cluster (difficult to setup and maintain and requires I believe 3 servers just as controllers). With a dual-master you just have a different off-set for the keys and you should be good, but of course there is the chance that at some point replication will halt because of an unexpected or unforseen error........

  • Dovecot Enable SSL/TLS with your certificate


    Dovecot enable SSL (by default it uses an old expired cert if you choose pop3s and imaps as protocols) =================== Create Cert & Key: openssl req -new -x509 -nodes -days 1530 -out server.crt -keyout server.key mkdir /etc/mailssl chmod 700 /etc/mailssl cp server.* /etc/mailssl Edit /etc/dovecot.conf ssl_cert_file = /etc/mailssl/server.crt s........

  • Postfix Enable SSL/TLS with your certificate


    Create Cert & Key: openssl req -new -x509 -nodes -days 1530 -out server.crt -keyout server.key mkdir /etc/mailssl chmod 700 /etc/mailssl cp server.* /etc/mailssl Postfix SSL config Edit /etc/postfix/main.cf: #SSL stuff smtpd_tls_cert_file = /etc/mailssl/server.crt smtpd_tls_key_file = /etc/mailssl/server.key To make smtps w........

  • CPU #1 not responding - cannot use it.


    I think this will be useful to others because I have a server that kept crashing mysteriously during intense disk usage/RAID checks. It would only crash during the weekly RAID integrity check. ThenI noticed during a reboot that not all CPUs were being brought up, as a result this actually creates much higher temperatures with the output I got from sensors, just booting the system produced higher than normal temperatures. You can imagine that a full blown RAID check........

  • named/bind cannot find zone file, load zone files without specifying full directory path/loading master file genuine.com.zone: file not found


    genuine.com/IN: loading master file genuine.com.zone: file not found _default/genuine.com/IN: file not found I always found it silly that no one really talks about this and apparently many like me and even control panels like Plesk were still using hard paths. I always thought "why can't I just specify the name of the zone file and have bind find it". Surely the default search path must be /var/named or somewhere else but there is no such thing.........

  • Ubuntu 9.04 Crash


    CPU/Kernel/MB/RAID problem? Jan 5 12:45:05 testbox kernel: [653298.890004] BUG: soft lockup - CPU#0 stuck for 61s! [hal-acl-tool:4168] Jan 5 12:45:05 testbox kernel: [653298.890005] Modules linked in: vmnet vmci vmmon binfmt_misc drbd video output input_polldev ocfs2_stackglue ocfs2_dlmfs ocfs2_dlm ocfs2_nodemanager configfs k8temp hwmon_vid lp snd_hda_intel snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi........

  • Plesk: Backup Domains from the CLI - it's quicker


    Plesk 8.6 CLI backup: /usr/local/psa/bin/pleskbackup domains domain.com This is a much better way of doing it and of course it can be scripted, it's a real pain to point, click and wait for Plesk to backup domains (and yes Iknow you could do all of them in a single client file but this is not desirable for my situation).........

  • mysql backup/dump all databases with mysqldump command


    mysqldump --all-databases > allDB.sql The above dumps ALL the mysql databases to "allDB.sql". If you want to compress with gzip you could do this instead: mysqldump --all-databases > gzip > ALLDB.sql.gz........

  • Installing Webmin & Enabling SSL


    Webmin Setup Centos 5: wget http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html&ts=1294339690&use_mirror=surfnet [1] 24229 [2] 24230 [root@host ~]# --2011-01-06 21:48:20-- http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html Resolving downloads.sourceforge.net... 216.34.181.........

  • Virtualmin/Webmin Postfix Error: The status of your system is being checked to ensure that all enabled features are available, that the mail server is properly configured, and that quotas are active ..


    Virtualmin Postfix Error: The status of your system is being checked to ensure that all enabled features are available, that the mail server is properly configured, and that quotas are active .. A problem was found with your Postfix virtual maps : No map sources were found in the Postfix configuration .. your system is not ready for use by Virtualmin. ........

  • Cygwin and crontab backups via ssh/scp/rsync


    Install the "Editors" and "Net" groups that will give you rsync, ssh, ssh-keygen and cron. The trickiest thing that I keep forgetting about each time is you have to run "cron-config" which adds the cron service to Windows, and without doing that obviously no cron jobs will be run thus making automatic backups impossible. Warning about rsync/cygwin and using the -a archive switch. It's a good thing I caught this because it doesn't work ri........

  • Dying Seagate 7200.11 SD15


    [137392.910057] ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x80000 action 0x6 frozen [137392.910077] ata4: SError: { 10B8B } [137392.910095] ata4.00: cmd 60/20:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 16384 in [137392.910099] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [137392.910122] ata4.00: status: { DRDY } [137392.910135] ata4: hard resetting link [137393.440060] ata4: SATA link........

  • vmare server - Cannot open the disk '/mnt/sda4/vmware/Debian/hdd.vmdk' or one of the snapshot disks it depends on. Reason: Failed to lock the file.


    Go into the directory for your Virtual Machine and delete all ".lck" directories. rm -rf *.lck After that your server should boot.........

  • rsync preserve attributes, permissions/ownership and times without being root non-root user


    One of the purposes of rsync is to backup whole filesystems and archive them but how can you do that properly and restore things to normal if all permissions and ownerships are not preserved from your root filesystem? It's not desirable to have everything running as root, especially not just for an rsync. The Easy rsync preserve permission solution for non-root users sudo is the answer and all you have to do is edit /etc/sudoers At the end o........

  • Outsourced VPS Support


    The Xen VPSI had was not working properly and when they asked for the login information I found the support was coming directly from India: whois 122.178.148.* [Querying whois.apnic.net] [whois.apnic.net] % [whois.apnic.net node-5] % Whois data copyright terms http://www.apnic.net/db/dbcopyright.html inetnum: 122.178.128.0 - 122.178.191.255 netname:&........

  • yum in Centos 5/Xen halts and exits suddenly


    yum exits in the middle The problem is this VPS seems to be an OpenVZ template from HyperVM. The only way to make it work was to disable i386 packages since this was an x64 kernel. That shouldn't be necessary but it was the only way to make yum stop quitting after the first package or two. I couldn't find any issue by checking the logs either. echo y|yum install vim-minimal telnet expect jwhois net-tools slocate iptables elinks gawk L........

  • mdadm RAID 1 adventures


    I separated the 2 drives in the RAID 1 array. 1 is the old one /dev/sda and is out of date, while the separated other one /dev/sdc was in another drive and mounted and used with more data (updated). I wonder how mdadm will handle this: usb-storage: device scan complete md: md127 stopped. md: bind md: md127: raid array is not clean -- starting background reconstruction raid1: raid set md127 active with 1 out of 2 m........

  • connect: No buffer space available Oct 18 12:21:03 vps kernel: printk: 177 messages suppressed. Oct 18 12:21:03 vps kernel: Neighbour table overflow.


    ping test.com connect: No buffer space available /var/log/messages Oct 18 12:21:03 vps kernel: printk: 177 messages suppressed. Oct 18 12:21:03 vps kernel: Neighbour table overflow. Solution in /etc/sysctl.conf: net.ipv4.neigh.default.gc_thresh1 = 4096 net.ipv4.neigh.default.gc_thresh2 = 8192 net.ipv4.neigh.default.gc_thresh3 = 8192 net.ipv4.neigh.default.base_reachab........

  • SolusVM/Xen Central Backup Warning - Takes System Off-line!


    This really gives me a bad impression of SolusVM. I tried the "Central Backup" option and it does not warn that your server gets shutdown instantly in order to do the backup! Further, there is no way to pause or cancel the backup. Thankfully this is a test/small disk usage VPS but what if someone was running something production with a large filesize? Ihaven't used QuickBackup but hope that isn't the same thing. Everyone should be vary car........

  • Subnet Mask Lengths / Quick Reference


    Subnet Mask Lengths / Quick Reference This is for when you say how many IPs would be in a /20 or /24 Now instead of doing math just remember this table or visit here more often :) /32 1 IP Address(es) /31 2 IP Address(es)........

  • How not to change an IP address in CPanel during a migration


    /usr/local/cpanel/bin/swapip domain(s) It simply doesn't work, the Apache VHOSTS remain 100% unchanged, why does this script exist? I'm sure it would work from the control panel but I am locked out because my IP was changed and it doesn't match the CPanel license. I wish CPanel would make it easier to update the license IP. I even took it a step farther, I manually edited the vhosts and restarted Apache and it........

  • CPanel Cannot Login Internal Server Error Could not fetch uid or gid for : root https://192.168.1.42:2083


    Internal Server Error Could not fetch uid or gid for : root https://192.168.1.42:2083 The reason for this is because the administration port is actually on port 2087, change the port and you'll be good to go.........

  • sed script to automatically update IPs in named/BIND and httpd/Apache


    Always make a backup of the original file before trying this, I find this kind of thing when updating IPs etc.. to use a script. Where the old IP is "192.168.5.8" and the new IP is "10.10.5.8" sed -i s/192.168.5.8/10.10.5.8/g testdomain.org.db The -i with sed means "inline" meaning we edit the file directly, but without the -i we could just use >and output the results to another file or do whatever else we wanted.........

  • VirtualBox Error Failed to start the virtual machine Centos 5.5 Mirror. Medium '/home/testuser/.VirtualBox/HardDisks/Centos 5.5 Mirror.vdi' is not accessible. UUID {a1a9fad7-0402-4867-b8f3-39fb49454bc5} of the medium '/home/testuser/.VirtualBox/HardD


    Virtualbox Error I tried to copy a .vdi of one container to use in another one, basically to clone instead of having to install the OS again. Failed to start the virtual machine Centos 5.5 Mirror. Medium '/home/testuser/.VirtualBox/HardDisks/Centos 5.5 Mirror.vdi' is not accessible. UUID {a1a9fad7-0402-4867-b8f3-39fb49454bc5} of the medium '/home/testuser/.VirtualBox/HardDisks/Centos 5.5 Mirror.vdi' does not match the value {4945a0e8-0ed5-4736-9088-bcaf........

  • OpenVZ/vzctl how to do an on-line migration without downtime


    vzmigrate --online dest-host VEIDNO eg.: vzmigrate --oneline 192.168.1.55 101 One option I would recommend is "--keep-dst", that way if the migration is interrupted you can still bring the VPS back up on the original host. After the migration is successful you can manually destroy it. OpenVZ has a good writeup on this including Checkpointing and Restoring etc:........

  • jailkit for chroot ssh account security tutorial and fix for error


    This was done on Centos butI think it's easier on Debian machines, the paths that it is set to use are tailored towards Debian, so there is some fiddling that needs to be done on Centos. This is for chrooting ssh, but jailkit has other uses than just SSH jails but I won't cover them in this writeup. 1. Install jailkit yum install jailkit 2. Setup Jail Home mkdir /home/jail chown root:root /home/ja........

  • exim high load and dozens of processes


    This server was experiencing loads of up to 80 and maxing out the RAM and kmemsize on a CPanel VPS. There were literally dozens if not hundreds of exim processes. I have no idea why exim has such a design that would allow it to consume this much CPU and RAM. Any normal MTA should not be spawning so many processes, it should be processing them in sequence and if it is going to spawn hundreds of processes in response to a large volume of mail, it's better to have a delayed del........

  • After installation Directadmin does not work directadmin dead but pid file exists on OpenVZ VPS when browsing http://ip.ip.ip.ip:2222


    After installation Directadmin does not work on OpenVZ VPS when browsing http://ip.ip.ip.ip:2222 service directadmin status directadmin dead but pid file exists tail /var/log/directadmin/error.log Check the value of your ethernet_dev=eth0 setting in your /usr/local/directadmin/conf/directadmin.conf file and the output of /sbin/ifconfig 2010:07:10-12:44:01: ioctl can't find........

  • mencoder Linux CLI video editing how to encode video file into xvid and split by time into multiple parts


    Mencoder is great, you can throw anything at it, including video files from your camera and have it encode into xvid or almost any other format. In my case I took 640x480 video from my Canon and reduced the size by 1/3 with the options below (there are many other options that you can read about in the manual but I like to keep it simple). Mencoder Encode mencoder -ovc xvid -oac mp3lame -xvidencopts fixed_quant=4 -o ........

  • Realtek r8169 1gbit/1000mbit NIC/Ethernet Goes Down/Halts on Large File Transfer/Heavy Network Usage


    This is obviously a bug in the r8169 kernel module and it seems to affect a lot of people. I upgraded to the latest kernel and hope this won't happen anymore, as it is a very serious error. This is especially serious for those who are running servers with this chipset, who can afford for the NIC to randomly go off-line for no apparent reason? [655548.189113] type=1505 audit(1277067560.902:5): operation="profile_load" name="/usr/bin/freshclam&q........

  • FUSE/Curlftpfs mount ftp account as drive partition in Linux


    This is a great way to use your ftp server space, for example on your web hosting account (althoughI believe many hosts don't allow storage like this), but if you have a VPS/Dedicated Server etc.., this would be perfect. Imagine how easy it is to work with an ftp account that you can just mount as a normal partition or directory in Linux, it would be great for backups etc.. Name curlftpfs - mount a ftp host as a local directory Synopsis........

  • Use rcconf to edit startup/init.d/init scripts on Debian/Ubuntu based distributions


    I've never understood how to enable and disable services for different run levels in Debian based distros, it's just weird, annoying and doesn't make sense. I much prefer chkconfig from RHEL. Just install the package called 'rcconf' and be done with it. rcconf makes things easy for you. apt-get install rcconf Reading package lists... Done Building dependency tree Reading state information... Done........

  • cPanel complaint - No Shared SSL! cPanel 11.25.0-R46156 - WHM 11.25.0 - X 3.9


    I've recently used CPanel on the admin side for the first time and have to say I hate it. Everything from the layout to the functionality screams "hackish". It just lacks so many common sense features and way of working. I was never 100% impressed with Plesk but the basics were definitely laid out and done in a sensible manner, even though it is made by a Russian company, they definitely thought about how to make a Control Panel. I have no idea why people........

  • How To Set DHCP/Static IP Address in Centos/RHEL/Fedora & Debian/Ubuntu/Kubuntu/MEPIS Set DHCP/Static IP Address


    Basically the two main types of distros are Debian and RHEL/Centos based. I'm just going to give a quick overview of how the configuration of IP interfaces works in Debian/Centos based distros. *Just one thing to remember, when setting IPs statically you have to manually specify a DNS server in /etc/resolv.conf (since DHCP is what normally does it automatically) Debian/Ubuntu/Kubuntu/MEPIS The IP (DHCP &........

  • Debian 5.04 RAID 1 mdadm boot problem GRUB error


    I successfully created a single RAID 1 partition which includes /boot inside it and my root directory through the Debian installer. It said GRUB installed successfully but when I try booting the OS it seems GRUB can't read anything. When trying to boot from GRUB GRUB Loading stage 1.5. GRUB loading, please wait... Error 2 I get "Error 2" when trying to boot Debian. I also notice from a LiveCD that........

  • Intel Corei5 750 Complaint/Onboard Video Issue on Intel H57 chipset not working


    Do you have an LGA1156 board and wonder why your onboard video isn't working? It's probably because there is no GPU integrated on the board itself, it is supposed to be on the CPU and new CPU's from Intel don't come with it! I was shocked to learn that you can buy a motherboard with onboard video which doesn't work. Inever knew it was being done or possible, but to make it worse the latest Core i5's don't have video on the die of the CPU. This means having on........

  • Asus O!Play cannot access network/workgroup shares


    It always worked fine before but no amount of power unplugging/cycling does any good. I can access one network share and that is one that I've already saved, but it can't see any workgroups. One silly thing is why is there no option to manually connect to a netbios name or IP? It seems there is a bug with the firmware and that the SMB client is not working properly. Hopefully it fixes itself at some point. Between this and the lack of support for embedded s........

  • Compile PHP 5.3.2 on Centos 5 and CPanel/WHM because of error - Fatal error: Call to > undefined function imagecreatefromjpeg()


    This function and others may not work with the stock PHPinstall on Centos/CPanel: Fatal error: Call to > undefined function imagecreatefromjpeg() Even with libjpeg-devel installed it won't work because PHP was not compiled with jpeg support, so we have to do the dirty work ourselves :) Here is the command/yum's I did to install missing libraries for PHP that configure will complain about (yes it is a one by one process). yum install bzip2-........

  • Unixbench Score on Core i5 750 with OpenVZ Kernel vs Xen/Openvz


    This was unbelievable how much the Xen kernel slows things down, keep in mind both tests were done on the hostnode, one was with the Openvz-Xen hybrid kernel and the other was just OpenVZ. You can see the performance difference is nearly 300% better when not using the Xen kernel. OpenVZ-Xen Kernel Test Results (I was wondering what was wrong/so slow with my Core i5!) # # # # # #&n........

  • OpenVZ user_beancounters kmemsize failcnt Processes Timing Out/Doing Nothing/Zombie


    cat /proc/user_beancounters produces the following: kmemsize 1861537 5139870 12752512 12752512 26965041 Notice the failcnt "26965041", that is for kmemsize and at first it confused me. The system had enough guaranteed and enough burst RAM available. kmemsize is a variable indepedent of that, but who cars about the explanation right, let's just make thing........

  • CPanel OpenVZ VPS Error - *** Notice *** No working loopback device files found. Try running `modprobe loop` as root via ssh and running this script again.


    Ihave no idea how to get the loopback device working in OpenVZ, but what's more frustrating is that I purchased a CPanel license for my VPS and clearly it is not "VPS Optimized". Although everything does seem to work at this point despite that error. The suggestions here: http://forum.openvz.org/index.php?t=msg&goto=1339 don't seem to work at all. This is an OpenVZ issue, but also a CPanel isue, why on earth would loopback support be expected in a VPS a........

  • get_printer_attrs: resource name '/printers/printers' no good! - cups error


    This is what the /var/log/cups/error.log says after my Samsung CLP-310N decided to stop printing. This is a new printer that replaced my CLP-300 and it has been working for a day so far. What happened is that I lifted the top part (not realizing there were rollers on it) and it stopped printing. The network activity light was flashing ,hitting the stop button didn't do anything. Even powering the printer on and off did not help. I have restarted CUPS and SMB on the........

  • rsync my favorite/best/optimal default switches and options


    Not sure what rsync switches/options to use? rsync -PDrphogtl The short version would be: rsync -Pha I think these are really common sense options to use and probaby should be the default. Explanation of rsync switches P = display the progress D = hybrid of --specials and --devices so all special and device files will be copied as well. r = recursive (otherwise rsync won't copy files deeper than........

  • Seagate Drive 500GB Drive Dying


    This drive is clearly on the way out, the Kernel knows it but I'm surprised that SMART is not concerned. I didn't blame Seagate for their past issues until now. This hard drive has hardly been used and has not even been powered on for a year according to SMART. Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device........

  • Linux AHCI Hotswap Tips - Remember To Reread The Partition Table WITHOUT rebooting


    From the package "parted" you can use the command "partprobe" to re-read the partition table. I really hate rebooting, and that's what Iloved to hear about AHCI motherboards, that they allow hotswap so you don't have to reboot. But that's only as good as the OS, if the OS does not reload the partition table you won't be able to do anything with that new drive you attached without rebooting. Yes, even without re-reading the partiton table Linux will........

  • nginx - the ultimate load balancer


    You can find it for free at http://nginx.org/ I find nginx is simpler to setup than pound (it's not hard but I found it unintuitive and annoying), it seemed to make some basic setups overly complicated with the config file syntax. nginx on the other hand is perfectly suited in everyway, it is even simpler to setup and seems to be the most stable and most efficient any load balancer. I would go as far as to say that a good nginx setup is more relia........

  • Convert HDD/Hard Drive Partition(s) into non-RAID into RAID 1 using existing data without data loss and without reformatting.


    Before we start I take no responsibility for this, you should have a backup and if you make a mistake during this process you could wipe out all of your data. So backup somewhere else before starting this as a precaution, or make sure it's data you could afford to lose. The RAID 1 Setup (Hardware Wise) I've already setup my 2 x 1TB (Seagate) drives with identical partitions, make sure your new hard drive (the empty one) is setup like your curr........

  • Monitor MB/s Disk IO Usage/Bandwidth - Use iostat from the sysstat Package


    The binary "iostat" comes from the package "sysstat" and is available on all Linux/Unix like platforms. Use the "-m" option to give you what you probably want, which is to see in MB/s how much bandwidth each disk is doing. iostat -m Linux 2.6.24.2 ((none)) 04/16/10 avg-cpu: %user %nice %system %iowait %steal %idle ........

  • tar gzip: stdout: File too large - Error Size Limit on Large file > 17GB


    The folder I was trying to archive is about 72GB, but much like rsync at about 17GB it chokes because of the filesize. What's with so many common and essential Linux tools having such limitations? I guess it is likely that the authors never wrote their code with the idea that files would be so large but it's still very annoying. It's important to stay on top of these limitations on production servers because I didn't realize what happened until I checked the file with "........

  • Picking an FTPD (vsftpd) Server in Linux Centos/Debian


    I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find. yum search ftp Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * rpmforge: ftp-stud.fht-esslingen.de * base: mirrors.netdna.com * updates: updates.interworx.info * addons: yum.singlehop.com * extras: mirrors.netdna.com rpmforge........

  • OpenVZ backup container to a single file while it's running using "vzdump"


    Proxmox has made this free utility to backup running OpenVZ containers. It's a great program which is actually just a PERL script but gets the job done. This program is not 100% required because all it really does is cp -a from your container's path as far as I know but it is still good to have uniformity to how you backup your containers. For RPM distros such as Centos/RHEL/Fedora etc.. download and install this: wget http://www.proxmox.com/cms_proxm........

  • Compaq V2405CA Laptop - Unixbench Performance Test


    Here are the results, it is Sempron 3000+ AMD Mobile, 500Gig HDD, 512MB RAM with shared ATI Radeon graphics. # # # # # # # ##### ###### # # #### # # # # ## # # # #&nb........

  • PHP cannot access /usr/bin/openssl


    PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist: [code:1:1fd0f3abbe] if (!file_exists($OPENSSL)) { //echo "ERROR: OPENSSL $OPENSSL not foundn"; }[/code:1:1fd0f3abbe] I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........

  • rsync bash script


    rsync bash script [code:1:722d8a25c1]#!/bin/bash # config --------------------------------- # two methods # from = receive data from another server # to = send data to another server rsync_method=from rsync_ip='192.168.5.18' local_dir='/home/backupguy/backups' remote_dir='/home/backup' free_space_bin='/home/backups/freediskspace.sh' # config end ------------------------------ if [ '$rsync_me........

  • Javascript Get a specified element using getElementById()


    Javascript Get a specified element using getElementById()Great, it produces the value for whatever "id" is passed to the function. http://www.java2s.com/Code/JavaScript/Development/GetaspecifiedelementusinggetElementById.htm [code:1:1287ede953] function getElement(){ var x=document.getElementById("myHead........

  • JavasScript how to set or write value in id tag


    JavasScript how to set or write value in id tagbla I need to set a value inside that DIV tag using Javascript, how would I do it?Doesn't work for me: [quote:c6b5f693a5]Warning: Element referenced by ID/NAME in the global scope. Use W3C standard document.getElementById() instead. Source File: http://hosting.com/vps-order.html Line: 19[/quote:c6b5f693a5] [code:1:c6b5f693a5]........

  • Convert PS2 controller to PC USB Controller


    Convert PS2 controller to PC USB ControllerSuper Joy Box 3 Pro http://www.play-asia.com/paOS-13-71-6m-49-en-70-qc2.html........

  • Nice General Linux RAID 1 Guide


    Nice General Linux RAID 1 GuideFull examples/tutorials that should work for any Linux system using GRUB or LILO as the boot loader. This is the only tutorial I've seen that clearly shows how you can convert an existing non-RAID system to software RAID1 remotely, without ever having to be at the computer. This is important for people who co-locate or rent dedicated servers that they may not have physical access to in a timely manner. https://alioth.debia........

  • Upgrade Release Kernel Tips


    Upgrade Release Kernel TipsThis is for CentOS 3.1 to 3.8 but the methodology will apply everywhere. I ran into a problem first of all with a non-booting system after running #yum update centos-release It took me to 3.8 and upgraded all the other packages [b:7e931c835d]BUT[/b:7e931c835d] because of some stupid flags enabled in /etc/yum.conf the KERNEL WASN'T UPGRADED SO AFTER BOOTING, WELL IT DIDN'T BOOT OF COURSE :) H........

  • E-mail (Thunderbird) with GnuPG encryption


    E-mail (Thunderbird) with GnuPG encryptionThis is great tool for Mozilla Thunderbird which allows you to encrypt your e-mails so only you and the receiver can view it even if the e-mail is intercepting or obtained by another person. The only small catch is that you of course have to install an extension to Thunderbird and then configure each account you want to use it with. Really it can probably all be done in a few minutes and the effort is worth it.........

  • E-Mail Tip


    E-Mail TipI just thought I'd give you guys a good tip about e-mail. It seems a lot of people like to use a Hotmail or ISP (eg. Telus) account for their e-mail but the problem is what happens if you switch ISPs, then your e-mail address no longer works and old friends might not be able to contact you. The same thing has happened for excite.com e-mail addresses where they just shut down. Whether you are a business owner or personal user can you afford to lose an e-mail........

  • Intel's Finnish Fetish


    Intel's Finnish FetishIntel's Finnish Fetish By Dave Mock June 13, 2005 Chipmaker Intel (NASDAQ: INTC) has successfully topped the personal computer market for decades. Breaking into related areas such as communications has been much difficult for the world's largest semiconductor maker. But a new partnership with Nokia (NYSE: NOK) could help to change that. Intel's forays into cellular-phone and home-entertaiment-device chips have........

  • Intruder detection device uses behavioural analysis


    Intruder detection device uses behavioural analysisIntruder detection device uses behavioural analysis by Antony Savvas Monday 13 June 2005 Symantec is introducing a new intrusion detection product that uses behavioural analysis to block potential attacks on enterprise networks. The new Critical System Protection 4.5 system uses technology that Symantec acquired through last year’s purchase of Platform Logic. It is designed to protect deskt........

  • Canada Net Speed


    Canada Net SpeedWhat is the fastest internet I can get in Canada?A lot of ISPs offer 10mbit cable such as Cogeco or some other one in Halifax I think. I can't remember the name. Right now cable internet will offer the fastest.........

  • PHPBB Drop All Tables


    PHPBB Drop All TablesSQL Syntax: [quote:75acd496c1]drop table phpbb_auth_access, phpbb_banlist, phpbb_categories, phpbb_config, phpbb_confirm, phpbb_disallow, phpbb_forum_prune, phpbb_forums, phpbb_groups, phpbb_posts, phpbb_posts_text, phpbb_privmsgs, phpbb_privmsgs_text, phpbb_ranks, phpbb_search_results, phpbb_search_wordlist, phpbb_search_wordmatch, phpbb_sessions, phpbb_smilies, phpbb_themes, phpbb_themes_name, phpbb_topics, phpbb_topics_watch, phpbb_user_group, p........

  • Cool SNMP tutorial/info


    Cool SNMP tutorial/infohttp://www.dpstele.com/layers/l2/snmp_l2_tut_part1.html........

  • Create Table with structure of another existing table


    Create Table with structure of another existing tableOk, this has many valid uses such as if you need to create backups or the ability to undo changes, you would want to create new tables with the same structure as another. Here is how you do it. [i:7ed9581493] Also remember Indexes such as PRIMARY KEYS [b:7ed9581493]will not be preserved[/b:7ed9581493] so you will have to readd them manually.[/i:7ed9581493] [code:1:7ed9581493]CREATE TABLE NewName AS SEL........

  • Bash Script Info


    Bash Script Infohttp://www.faqs.org/docs/Linux-HOWTO/Bash-Prog-Intro-HOWTO.html#ss10.5 http://www.scit.wlv.ac.uk/~jphb/spos/notes/shell/shell5.html http://quong.best.vwh.net/shellin20/#LtohTOCentry-41 http://www.cactus.org/~dak/shellscript.html http://db.ilug-bom.org.in/Documentation/abs-guide/ http://pegasus.rutgers.edu/~elflord/unix/bash-tute.html http://heather.cs.ucdavis.edu/~matloff/UnixAndC/Unix/CShellII.html Since bash i........

  • It's not all about the speed.


    It's not all about the speed.I'd also thought I'd mention that speed is not everything. Routing is the key, because if one router you hit is slow then it doesn't matter how fast your connection is. I have found that locally, Telus has much better routing than Shaw (although I have not yet tested their new DOCSIS network). There are also some countries such as Sweden that offer high speed connections, but the high speed only applies locally. The reason is that man........

  • How do you copy a DVD


    How do you copy a DVDHow do you copy a DVDI'm assuming you mean how you can backup your DVD titles? If you are talking movies, you should use AnyDVD and CloneDVD, they are excellent tools for backups. For data CD's, Nero has a DVD-Copy option and that should work well for most purposes. Hope that helps. :D........

  • Basic Port Listing


    Basic Port ListingHopefully someone finds this useful or at least interesting. http://www.sans.org/top20/#u9 Name Port Protocol Description Small services ........

  • Telus Begins Enforcing Bandwidth Caps


    Telus Begins Enforcing Bandwidth CapsIt appears Telus has begun to send e-mails out and is planning on enforcing bandwidth caps of only 10gigs/month for their 1.5mbit plan and 20gigs/month for 2.5mbit The state of Canadian ISPs is horrible :( In the east coast, Bell Sympatico will allow you to have unlimited bandwidth and even Aliant will and they have 3mbit for a much more affordable price than our 2.5mbit on Telus. Telus needs to get wit........

  • Linux Kernel Error (2.6.33.1) BUG: Bad page state in process swapper - Keeps rebooting - initramfs bug


    *This is a bug with initramfs support, all kernels after around 2.6.27.54 suffer from this problem. If you try to include initramfs into your kernel (I mean actually building your binaries into the kernel) this will always happen. Obviously some code has changed in recent kernels that is present in all new kernels, it makes it impossible to boot I've tried the latest 2.6.32, 2.6.33, 2.6.34, 2.6.35, 2.6.36, 2.6.37, 2.6.38 kernels and they all do this. I found one bug re........

  • MySQL "Got error 28 from storage engine"


    I've gotten this error enough to bother posting about it, because I've come across so many servers where this happens, so what could "Error 28" possibly mean? Is your database corrupt, or is this a sign of a RAID failure/corruption or even worse, bad blocks on a clients system who has no RAID and never took backups? No, check your free blocks, it simply means you have no space. This was the result of a script that was overzealous and backed up the entire database........

  • How to Track Down/Find Cause of Linux high disk iowait/wa


    top - 09:34:12 up 2 days, 20:57, 2 users, load average: 1.83, 1.99, 2.03 Tasks: 59 total, 2 running, 57 sleeping, 0 stopped, 0 zombie Cpu(s): 0.3%us, 0.0%sy, 0.0%ni, 0.0%id, 99.7%wa, 0.0%hi, 0.0%si, 0.0%st That 99.7% wa is iowait, it means the server is waiting for a process to complete an IOoperation or in plain English, there is a delay in........

  • Openvz "Container already locked" Error Message Solution/Fix


    I didn't find any useful information that actually fixed this. My VPS was in the "Running State" and I could not stop or restart it. I kept getting "Container already locked" no matter what Idid (I tried all the suggestions in the Google results for this error). Most of the suggestions were for Windows but I only use Linux. The other solutioins also said to restart the VZ service or even the entire hostnode and this was not acceptable to me........

  • Unixbench Score with Glusterfs/Openvz & Quad Core Xeon - Updated with GlusterFS 2.0.8 & Optimized Client Config


    The results are still not flattering and are nothing close to native performance. Unless GlusterFS has a "DRBD-like" option to delay writes over the network and to only read from the client side, I don't see how performance can ever improve much more. After doing some client optimizations Iadded more to the score: Start Benchmark Run: Sun Nov 29 00:37:44 PST 2009 00:37:44 up 3 min, 1 user, load average: 0.01........

  • Clustered/Distributed Network Filesystems, Which Ones live up to the hype?


    I've tried to find a good sensible solution to cluster with and each technology has it's pros and cons and there is no perfect solution and I've found a lot of "exaggerations" in the applications, benefits and performance of these different filesystems. DRBD I first started off with DRBD and Ihave to say it does live up to the hype, is quite reliable (although it can be annoying to match up the kernel module and user applications since they must match and whe........

  • Unixbench Score with Glusterfs/Openvz & Quad Core Xeon - Updated with GlusterFS 2.0.8


    You might remember my original GluserFS/OpenVZ benchmark which produced a horrible 29.8 This is the exact same system, but using the latest 2.0.8 (with some small files patch which speeds up performance) you can see it is about 25% faster. I also haven't tuned my config files at all, but there are some settings that should increase performance on small files which I believe i........

  • Tyan S2735-8M Maximum Hard Drive Limit/Not Working/Doesn't work with 1TB 1000GB hard drives


    Inever saved any of the logs, but basically no matter what OS (Linux)I used, I could not get my 1000GB hard drive to work (Seagate SATA). The BIOS recognizes the drive and fdisk -l shows the hard drive as it should. The tricky thing is that different OS's will give you different results, but don't be fooled. You can't use these larger drives for long. Iwas getting all kinds of seek/IOerrors and also messages that the port could not be read.........

  • Unixbench Score with Glusterfs/Openvz & Quad Core Xeon


    This is very disappointing since GlusterFS markets itself as a solution to deploy VPS servers on. On the HNitself I get a Unixbench of about 360. I'm also using an SSH tunnel to secure the communications, but even before that, things seemed very slow. # # # # # # # #####&n........

  • Timezone Change/Updated for Linux/Unix Debian/Fedora/Ubuntu/Centos Change Update Time zone


    In Newer Linux Distros This Way Is Easiest and works on newer versions like Ubuntu, Mint, Fedora, Centos, Debian etc. #if you are missing timedatectl this in newer distros like Ubuntu/Mint/Debian and are using a container like Docker then do "apt install systemd" timedatectl set-timezone America/Vancouver Replace the America/Vancouver with the correct timezone. To see the list you can just type "timedatectl set........

  • Have an OpenVZ VPS/Linux Virtual Private Server and nothing works right?


    A VPS Server I had just wasn't working right, code that I migrated there just wasn't working. For example, it kept telling me the connection to the database was unsuccessful, halfway through iterating through results it already had. Then I realized it wasn't my code. Ichecked my /proc/user_beancounters and found this: cat /proc/user_beancounters Version: 2.5 uid resource held maxheld barrier limit failcnt........

  • MySQL Restoring And Dumping/Backing UP MySQL Data/Tables/Databases


    Backing MySQL Databases Backing Up/Dumping All Mysql Databases To A Single File mysqldump --all-databases -u admin -p > allmysqldatabases.sql The "-all-databases" clause is pretty obvious isn't it? It means that it will backup all databases. The "-u admin" means login using the user "admin", if you h........

  • Why Apple should thank the jailbreakers and not patch/stop the jailbreaking exploits


    First of all, the iPhone is crippled in many ways, but most of my complaints about functionality have been addressed through the jailbreak, Ican run apps in the background of my choosing, I can install a terminal, acccess my phone through SSH and SCP and so much more. It even addresses the 15 minute e-mail problem, I installed a program called "PushMod" and now set the checking time to just 1 minute. Apple should really thank the developers for this gift, it ma........

  • iPhone Backgrounder Adds True and Real iPhone multitasking on jailbroken phones


    Apple crippled the iPhone by not allowing multi-tasking of the non-primary apps. I use SSH a lot and I don't want to close my session just to check my e-mail, etc, now an app found in Cydia called "Backgrounder" allows just that. Although it's not perfect, we installed the correct one for "3.x" iPhones and hit "Reload SpringBoard" and the hour/circle glass has just been going for minutes. It seems like it installed fine even with the crash t........

  • iPhone/iTunes sync error "0xE8008001"


    This happened during a sync of my iPhone while installing some apps. This usually happens to non-jailbroken iPhones who are trying to install non-Apple approved software OR jailbroken phones who haven't done the "Sync update". How to fix this error and get the Sync Update Open Cydia - Manage - Sources - Edit Add this source: http://cydia.hackulo.us Then under the section "Hackulo.us" install "Ap........

  • iPhone 3GS Jailbreak Information & Benefits


    Truly, the only way to unleash the capabilities and customization abilities of iPhone are to jailbreak, it's not just for hackers anymore. A few days ago someone by the named of "geohot" released a single click application called "purplera1n", which does the entire operation smoothly and seamlessly. In our case, the first time it went as far as "done, wait for reboot" on our Windows machine and for minutes we waited and saw the pic on the iPhone w........

  • iPhone 3GS 32GB "Harsh Review"


    Yes, Iadmit I finally got bitten by the hype as much as I can usually see through it all. Keep in mind this review is of the "stock" phone, no jailbreaking yet which is what really unleashes the customizability and whyI bought iPhone. I had better things to say about this phone before buying it, and it is a great phone, perhaps the best on the market by far, if not because of the Mac OS port onto the iPhone and all the apps, etc, etc. With that said........

  • iPhone has no password/wand manager saving feature in Safari Web Browser


    I kind of expected this feature to be there in some form, to stay ahead of the pack Apple needs to stay on top of this. User's of HTC's Android smart phone which uses a Linux based OS with Google's power behind it, note that you can save passwords in the browser on that phone. Apple needs to continuously evaluate the needs in its core apps and make sure the features are cutting edge and top notch, if other phones come out with some of these seemingly small but essential features........

  • Apple iPhone 3GS and predecessors are leading a revolution


    As much of a computer nerd as Iam, I'm usually a late adopter to technology for a few reasons. Ifeel most new hyped technologies and electronics are mainly fads, and I'm also cheap. Adopting later means you avoid the bugs, kinks and most importantly pay the lowest price, that's me being cheap again :) I never read much about the iPhone but Isaw all the hype around it and until recently I wasn't a big fan of anything Apple until a few years ago I realize........

  • Nokia N97 review, feedback and complaints


    I've had an old Blackberry for a few years and I was ready to spend some serious cash on a nice Nokia. I love the idea of the Linux based Symbian S60 OS, so I was looking at phones like the E63, E71 (both are basically the same, at least CPU/screensize although E71 is thinner, has a 3MP camera, has GPS, and has dedicated buttons to adjust the volume). Then Iheard about the N97 and what a revolution it was supposed to be and it was even compared to iPhone. To........

  • RTL8111/8168B R8169 Gigabit Link slow speeds


    This is the Intel Atom 330 motherboard with integrated Realtek Gigabit NIC (Intel Desktop Board D945GCLF2 Motherboard W/ Atom 330 1.6 GHz Dual Core Processor - Mini-ITX) I cannot achieve more than 15 MB/s, even doing a local transfer through eth0 to it's own IP. 100% 95MB 15.9MB/s 00:06 So this is not a cabling, switch or hardware issue, it seems like a driver or chipset limitation problem. Here is my........

  • SSH Server Slow/Lagged/Delayed Login Response


    This is really something the SSHServer developers should consider. The cause of this annoyance is because of failed DNS lookups on your IPaddress, which is especially common for many dedicated/col-located servers and also computers on internal NAT/private networks. The chances are this is the cause of your SSHSlow/Delayed Login problems. The easy solution to SSH Login Problems Edit /etc/ssh/sshd_config Add this line to disable r........

  • OCFS2 crash


    When trying to even cd or ls the mounted OCFS2 partition it crashes. Ithink this is a combination of VMWare Server's problem and the way I mounted and symlinked to it. More than anything this shows the problem and lack of forsight with VMWare, but also that OCFS2 is easily crashed if you do strange things. Output of /var/log/messages for OCFS2 Apr 10 15:57:45 localhost kernel: [84331.691258] Modules linked in: vmnet vmci vmmon ocfs2_stac........

  • Samba SMB Error - Server not using user level security and no password supplied. tree connect failed: NT_STATUS_WRONG_PASSWORD


    Server not using user level security and no password supplied. tree connect failed: NT_STATUS_WRONG_PASSWORD That happens when trying to use smbclient to connect to a share. The weird thing is that I can authnenticate just fine from Windows XP. It is partially my mistake, I forgot this share does have a password. I've tried authenticating with the correct user and also with "Guest" because this works in Windows. In Linux I ........

  • ENOM Major Outage


    At this time we can't resolve Enom's website and all DNS requests to their 4 primary name servers are failing, although the hostnames themselves still resolve: Name Server: DNS1.NAME-SERVICES.COM Name Server: DNS2.NAME-SERVICES.COM Name Server: DNS3.NAME-SERVICES.COM Name Server: DNS4.NAME-SERVICES.COM Name Server: DNS5.NAME-SERVICES.COM You would really think Enom, bein........

    • Latest Articles

  • FreePBX 17 How To Add a Trunk
  • Docker Container Onboot Policy - How to make sure a container is always running
  • FreePBX 17 How To Add Phones / Extensions and Register
  • Warning: The driver descriptor says the physical block size is 2048 bytes, but Linux says it is 512 bytes. solution
  • Cisco How To Use a Third Party SIP Phone (eg. Avaya, 3CX)
  • Cisco Unified Communication Manager (CUCM) - How To Add Phones
  • pptp / pptpd not working in DD-WRT iptables / router
  • systemd-journald high memory usage solution
  • How to Install FreePBX 17 in Linux Debian Ubuntu Mint Guide
  • How To Install Cisco's CUCM (Cisco Unified Communication Manager) 12 Guide
  • Linux Ubuntu Redhat How To Extract Images from PDF
  • Linux and Windows Dual Boot Issue NIC Won't work After Booting Windows
  • Cisco CME How To Enable ACD hunt groups
  • How to install gns3 on Linux Ubuntu Mint
  • How to convert audio for Asterisk .wav format
  • Using Cisco CME Router with Asterisk as a dial-peer
  • Cisco CME How To Configure SIP Trunk VOIP
  • Virtualbox host Only Network Error Failed to save host network interface parameter - Cannot change gateway IP of host only network
  • Cisco CME and C7200 Router Testing and Learning Environment on Ubuntu 20+ Setup Tutorial Guide
  • Abusive IP ranges blacklist
    • Copyright © realtechtalk.com 2024