Disk /dev/sdb: 15.22 GiB, 16336814080 bytes, 31907840 sectors
Disk model: SD/MMC
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x00000000
The fdisk output is above and below is the error you may get when trying to use the d........
FreePBX official install guide is here.
Requirements:
Debian 12 Download Link
Minimal - System Utilities
RAM: 4G
HDD:20G
Note that if you don't have the required base OS yo........
Just use pdfimages:
Change yourpdf.pdf to the name of your pdf
output-name is the name format (eg. output-name01.jpg output-name02.jpg) is how the files will be named if you use "output-name". Change as needed.
pdfimages -all yourpdf.pdf output-name
After that you will have extracted all of the images.
You can also just run the command with -list and see all of the images contained within the pdf lik........
In Windows, with some NICs, especially Intel, Windows may enable features on the card that break it in Linux. It is hard to troubleshoot as what you'll see is that the NIC is still detected in Linux, the NIC/port will be up but nothing will work (eg. DHCP requests or even static IPs won't work). You may see STP bridge traffic but that is all.
In a corporate environment this can result in many calls to support and is essentially downtime and an unnecessary waste of resource........
Step 01 - Download
Visit https://gns3.com/software/download
Click on "Linux" on the side under "Installation".........
Since newer versions of Ubuntu like 20, you will find there is no longer dynagen and that the dynamips provided is faulty and will segfault each time:
Cisco Router Simulation Platform (version 0.2.14-amd64/Linux stable)
Copyright (c) 2005-2011 Christophe Fillot.
Build date: Apr 3 2018 12:20:29
Local UUID: 3c1c0b7f-2fab-4fda-b40b-74841d1bcfe0
Instance ID set to 1.
netio_tap_create: unable to open TAP device tap1 (No such fi........
Uses:
Install OS on physical drive
Linux installation VMware
Install Windows on physical drive
Boot OS from physical drive
VMware Workstation tutorial
Linux virtual machine to physical disk
Windows to Linux migration
Dual boot OS installation
Boot from external SSD
Linux, Windows, BSD installation guide
Physical drive boot OS........
yum update
Loaded plugins: fastestmirror, ovl
Determining fastest mirrors
Could not retrieve mirrorlist http://mirrorlist.centos.org/?release=7&arch=x86_64&repo=os&infra=container error was
14: curl#6 - "Could not resolve host: mirrorlist.centos.org; Unknown error"
One of the configured repositories failed (Unknown),
and yum doesn't have enough cached data to continue. At this point the onl........
A lot of times you may see when installing packages that apt will recommend packages, a lot of times when doing things like upgrading or install a new kernel, it is very smart at recommending related packages (eg. modules, headers, extras etc..)
All you need to do is add this flag to your "apt install" command:
--install-suggests........
Just export these variables:
export http_proxy="socks5://127.0.0.1:1234"
export https_proxy="socks5://127.0.0.1:1234"
The above example uses a socks 5 proxy at localhost and port 1234.
This is a great way to improve performance of some activities for things like package installation, especially if your routing is not ideal to the repos.........
Use gs or ghostscript as below, specify the output file and also the input file.
In the example below the output file is "outputfile-resized.pdf" and the input file is "original-pdf.pdf". Change the input file to the name of your pdf
gs -sDEVICE=pdfwrite -dCompatibilityLevel=1.4 -dPDFSETTINGS=/prepress -dNOPAUSE -dQUIET -dBATCH -sOutputFile=outputfile-resized.pdf original-pdf.pdf
For........
Hyper-V uses obscure virtual hardware, you can enable the FB device for Hyper-V but if you just need text/console to work just compile this option:
Device Drivers --->
Graphics support --->
Framebuffer Devices --->
Simpl........
In a lot of distros, vdpau which accelerates video through the GPUis often not installed even in recent distros. This will result in Firefox with Youtube dropping frames when you check the "Stats for Nerds" and to the eye as jerky or slower video playback due to the dropped frames.
Some sites will say that because you are watching VP09 that there is no GPU support, but with vdpau installed and enabled, many GPUs will still be able to use hardware decoding for 4K........
This example is using RTL8821AU chipset from a TP-Link T2U Plus USB adapter and other similar ones should work the same.
Here's how to get this chipset RTL8821AU working in Linux.
Here's how to get RTL8812 and RTL8822 working in Linux.........
This is mainly for if you've done something silly like trying to clone a Live, running VM image. In this example, the VM initially finds grub and tries to boot but is kicked straight into initramfs rescue mode/busybox right after this.
If you've done this "silly" thing, you could have dataloss but a lot of times just using fsck will fix it as you are guaranteed at best to have some corruption and inconsistencies in the filesystem. My theory is that some files wer........
This guide assumes you have a working Postfix server and want it to sign with DKIM.
There are a few things we have to understand to make all of this work though, which require you to be familiar with DNS as well.
1.) Install OpenDKIM
apt install opendkim
systemctl enable opendkim
2.) Edit /etc/opendkim.conf
Syslog yes
SyslogSuccess yes
Mode&nbs........
apt install tftpd-hpa
#change TFTP_ADDRESS to by setting address to 192.168.1.1:69 or the IP you need, otherwise it will listen on all IPs and interfaces which could be a security risk.
# edit /etc/default/tftpd-hpa
TFTP_USERNAME="tftp"
TFTP_DIRECTORY="/srv/tftp"
TFTP_ADDRESS="192.168.1.1:69"
TFTP_OPTIONS="--secure"........
This sometimes happens when trying to install the EFIversion of grub to a device when you are booted into Legacy/MBR mode. It doesn't seem to occur on all machines, but some and seems somewhat BIOS dependent.
grub-install --target=x86_64-efi /dev/sda
Installing for x86_64-efi platform.
grub-install.real: warning: Couldn't find physical volume `(null)'. Some modules may be missing from core image..
grub-install.real: warning: Couldn't find physica........
This can break things easily in remove environments where it was normally easy to convert a normal eth0 to a bridge under br0, and that bridge would normally have the same MAC address by default, which is desirable for most situations.
In Debian 11 this is different for some reason now.
https://unix.stackexchange.com/questions/681013/bridge-gets-random-mac-........
This seems to happen in many different drivers but it happened more often in newer versions such as 530 vs 525.
Then nvidia-modeset goes to 100%
There are many reports of this appearing since driver 4.70 and I can confirm I've seen this in various machines.
https://forums.de........
Sometimes users take their removal drives and unplug and replug them to test what happens during the failure of a disk. However, this breaks things quite badly due to the /dev/mapper in LUKS not coming back online due to it not being closed.
In other words, generally with non-encrypted drives the process is smooth but when encrypted you may want to follow a strategy like this:
We can see below that both disks are unavailable as they were physically remov........
Have you got this error from Apache?
[notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec)
[error] (28)No space left on device: Cannot create SSLMutex
At first glance it appears that you may be out of disk space but the issue is ipc or interprocess communication.
This will clear out the ipcs processes so things can work, this often happens during high traffic and may be a sign of DDOS.
The command below will fix it, it will list al........
Even today we see a lot of servers that have different services and ports open for rpc and this creates not only potential inward vulnerabilities but perhaps more common, the abuse of your network resources in reflective rpc queries.
To stop this problem, you should disable and remove all services relating to rpc or at least block all relevant ports for the service.
Surprisingly, there are still some providers and OS installs in Linux that install these services and leave them........
This is a weird issue as sometimes when upgrading or even migrating, this could happen and the reason is simple but maybe not 100% obvious at first.
You will find that your GUIdoesn't load and most services fail to start, even logind
Here are some errors you may see:
Mar 13 22:22:23 rttbox systemd-logind[2892]: Failed to connect to system bus: No such file or directory
Mar 13 22:22:23 rttbox systemd-logind........
You may have been expecting a normal sized kernel but if you don't disable these .config options you may have a kernel that is several gigabytes.
CONFIG_SLUB_DEBUG=no
CONFIG_DEBUG_INFO=no
CONFIG_DEBUG_MISC=no
Rebuild and you should find that the kernel is the normal and as expected size.........
[ 0.206301] [Firmware Bug]: TSC_DEADLINE disabled due to Errata; please update microcode to version: 0x3a (or later)
[ 0.430409] MDS: Vulnerable: Clear CPU buffers attempted, no microcode
[ 0.430411] MMIO Stale Data: Vulnerable: Clear CPU buffers attempted, no microcode
[ 2.980359] microcode: sig=0x306f2, pf=0x1, revision=0x36
[ 2.981621] microcode: Microcode Update Driv........
First we need a few extra packages:
apt update
apt install -y adduser libfontconfig1 musl sudo
wget https://dl.grafana.com/enterprise/release/grafana-enterprise_10.3.1_amd64.deb
Install / Enable Grafana
dpkg -i grafana-enterprise_10.3.1_amd64.deb
dpkg -i grafana-enterprise_10.3.1_amd64.deb
(Reading database ... 44309 files and directories currently installed.)
Preparin........
This is for the situation that you're doing other things that may conflict or have your own custom rules and ufw keeps overriding iptables.
A lot of guides don't work, and even ufw reset does not work, because it still leaves the old ufw chains.
Here is what works to disable ufw completely
systemctl stop ufw
systemctl disable ufw
ufw disable
rm -f /et........
You are probably using some custom image or maybe this is some sort of container that didn't boot with systemd.
The solution is to use "reboot -f"
reboot -f
This will force the system/OS/VM/container to reboot.........
During a migration or other custom setup, it's possible you don't have a $HOME/Desktop and as a result the config file that controls this is set to just use your $HOME directory.
This is controlled in the file: $HOME/.config/user-dirs.dirs
As we can see below, Desktop, Downloads, Music and Pictures are set to $HOME. We can edit any of these as we like.
# This file is written by xdg-user-dirs-update
# If you want........
find /usr/share/zoneinfo/|sed s#"/usr/share/zoneinfo/"##g|grep "/"|grep -v posix|grep -v ^"Etc/"|grep -v ^right|grep -v ^"SystemV"
Africa/Addis_Ababa
Africa/Abidjan
Africa/Blantyre
Africa/Lusaka
Africa/Casablanca
Africa/Libreville
Africa/Asmara
Africa/Bujumbura
Africa/Dakar
Africa/Lagos
Africa/Malabo
Africa/Harare
Africa/Kigali........
Step 1.) Upgrade to Debian 11 first
The process to go to Debian 12 is not as smooth as 11, when trying to upgrade from Debian 10. In fact, it doesn't work directly, so you'll first need to follow this guide to update to Debian 11, reboot and come back here if successful.
Step 2.) Update sources.list
Update your /etc/apt/sources.list like this:
deb http://........
If you are running a local DNS server like named/bind and don't want to use the ISPsupplied DNS servers that are announced via a DHCP request (using dhclient) then the solution is simple.
The reason should be obvious, but normally running your own DNS server will provide a more reliable, and fast DNS response and you won't have to worry about filtering as much (unless your upstream filters or proxies outgoing DNS requests).
Edit /etc/dhcp/dhclient.conf........
If you have swarm services and dockerd is creating a high load even with the containers just being idle, the easiest solution is to upgrade to a newer docker version.
For example an identical config of 3 nodes, with Redis 5 with 30 replicas produces a load of about 1.45 in Debian 10 with Docker18.09.1
If I create the same setup on Debian 11, with Docker 20.10.5+dfsg1 then the CPU usage is low.
One other difference I wondered is the kernel. In my test setup........
This should work for most console ports of other manufacturers too. It is a quick and simple method for emegencies or deploying a few appliances/devices in a non-standard environment or small environment.
However, if this is a route thing, or the equipment is not physically close to you, it would be best to use some sort of "Terminal" server which is an IP connected switch with several serial ports built-in for this purpose. Normally they accessible by web/........
The issue is that Docker images are stripped down, so many tools and even python3 is missing, so you'll have to build or update the actual image yourself.
I assume you have started an image with something like this and that you have the Nvidia Toolkit installed (assuming you are using GPUs). If you're not using nvidia just remove --runtime=nvidia --gpus all.
docker run -it --runtime=nvidia --gpus all ubuntu bash
These works for most images li........
Welcome to our in-depth guide on configuring NVIDIA GPUs with Docker on Ubuntu. This post is tailored for developers, data scientists, and IT professionals who are looking to leverage the power of NVIDIA's GPU acceleration within Docker containers.
Whether you're working on machine lea........
You'll notice that /etc/resolv.conf contains dire warners on most Linux Desktops.
# This file is managed by man:systemd-resolved(8). Do not edit.
#
# This is a dynamic resolv.conf file for connecting local clients to the
# internal DNS stub resolver of systemd-resolved. This file lists all
# configured search domains.
#
# Run "resolvectl status" to see details about the uplink DNS servers
# currently in use........
Let's say you have a directory /mnt/raid which has files and directories inside it, but nothing is mounted to it.
Then you mount a block device such as /dev/sdh to /mnt/raid
Even though /mnt/raid has files and directories there, you can only see the mounted contents of /mnt/raid.
How do we access the original contents?
Just do a bind mount of the root filesystem to another location.
mkdir /bindmount
mount --bind / /b........
How to check what kernel version you have/currently running?
uname -rm
5.4.0-91-generic x86_64
The above shows us that we are running 5.4.0-91-generic on the x86_64 architecture.
The safest way is to stick with the same flavor eg if you're on generic, and say on kernel 5.4.0 then it makes sense to follow what is below. However, if you are migrating or dual booting between newer hardware (eg. you got a........
The passwords are stored in the following locations on Unix/Linux:
The directory is usually inside your home like this:
~/.mozilla/firefox
logins.json contains the locations, username and password
key*.db (usually then name could be key3.db or key4.db)
Without the key file you will not see any passwords in Firefox as it is required to in order to decrypt the contents of logins.json........
The issue is when you need to echo something as root/sudo, that it doesn't work. You can never do a sudo echo to an output file as you'd expect.
Take an example to clear out wasted RAM buffers/cache like this:
sudo echo 1 > /proc/sys/vm/drop_caches
-bash: /proc/sys/vm/drop_caches: Permission denied
The solution is to run tee as sudo/root
What we do is echo 1, but then pipe it to the "tee" command as sudo........
So you started a process or other important task that is remote but it is in the foreground and on a pts. This means if you background with Ctrl + Z or otherwise logout or get disconnected that the process will be stopped.
Here is how you can solve the problem:
1.) Hit Ctrl + Z to suspend the process.
2.) Type bg to restore the process into the background. If you do a ps aux on the process you will see it was restored with the & at the end, which puts........
We could always disable swap but this would normally be a bad idea unless you have an incredible amount of RAM and a workload that will never exceed it. However, for live/containerized and high performance environments it could be desirable.
Another middle ground may be to set swappiness to a lower number.
You may also want to clear your kernel's cache, which could be eating up RAM unnecessarily by c........
By default if you create a private key for SSH, it will create something like .ssh/id_rsa
Linux will always search for and offer this key when connecting to servers.
If you put extra keys in your .ssh directory like id_rsa_realtechtalk.com, they will be ignored by default and NOT used or offered (you can verify this with ssh -v) and see it is not being offered.
Here is how you add the extra SSH keys so they are all offered:
#this gives........
A lot of developers want to go to 3.11 because of the speed improvements, but most distros never have the latest Python version.
Using the deadsnakes third party repo is the easiest way aside from compiling it yourself (which is safer and recommended):
Step 1 - Add the repo
apt-add-repository ppa:deadsnakes/ppa
If you get an error about requests then install it:........
If you get this error in your logs:
add bridge failed: Package not installed
This error normally means one of two things.
1.) Is your brctl (bridge-utils) installed?
On Mint/Debian check for "brctl". If it's not there do
sudo apt install bridge-utils uml-utilities
2.) Is your bridge.ko (bridge kernel module loaded?).
On some installs I have seen that you cannot modpro........
This sort of thing normally happens your python3 or pip3 has been updated, because you have to in order to use pip, but the newer pip now breaks compatibility with your old python (3.5 in this case).
There are a few solutions, the easiest is perhaps to upgrade to a newer OS with a newer distro provided Python 3 or to manually install a newer version of Python/OR use a PPA like deadsnakes that provides newer versions.
........
If you get this error, it's usually because you don't have coreutils installed.
-bash: expr: command not found
Install coreutils and you'll be good:
apt-get -y install coreutils........
Install exiftool:
apt install exiftool
Remove the metadata from "thefile.pdf":
exiftool -all= thefile.pdf
Warning: [minor] ExifTool PDF edits are reversible. Deleted tags may be recovered! - thefile.pdf
1 image files updated
Metadata, in the context of PDFs, refers to a set of data that describes and gives informat........
haproxy is one of the best known and widely used Open Source load balancers out there and a strong competitor to nginx.
haproxy is used by many large sites per Wikipedia:
HAProxy is used by a number of high-profile websites including GoDaddy, GitHub,........
This is a weird issue in Mint Ubuntu gnome that I've only seen on one system. It may happen in your terminal or your browser but one program will just refuse to allow input from the keyboard. I am not sure if it's some weird fluke on a strange keyboard by perhaps accidentally hitting a weird key combination.
In some windows the keyboard gets weird and only / and Esc seem to work.
/ brings up quick find and sometimes Esc will close it........
If you are installing ta-lib for Python and get this error then you can normally solve it by manually getting the ta-lib source files and compiling.
tar -zxvf ta-lib-0.4.0-src.tar.gz
cd ta-lib;./configure;make;make install
Collecting ta-lib
Downloading https://files.pythonhosted.org/packages/39/6f/6acaee2eac6afb2cc6a2adcb294080577f9983fbd2726395b9047c4e13ec/TA-Lib-0.4.26.tar.gz (272kB)
&nbs........
Be very careful about what filename you specify in dhcpd.conf if you get an error like this:
NBP filesize is 0 Bytes PXE-E23:Client received TFTP error from server.
If you specify "BOOTx64.efi" then the file had better not be called "BOOTx64.EFI" as it is case sensitive. It's really a case of th........
1 - Install Vagrant
apt install vagrant
Make sure you have a supported Virtualization tool like Virtualbox or VMWare, Hyper-V etc.. It automatically detects and uses what you have. Virtualbox has a lot of support here with tons of images.
2 - Init Vagrant
We'll init to have a Debian 10 box by default to show how quick and easy it is.
vagrant init generic/debian10........
This seems to have changed for RHEL 8 where a normal dracut to update your initramfs creates a system that only boots for the running kernel. For example if you have Kernel 5 and then chroot into a RHEL 8 variant which uses kernel 4.18, and run dracut, it seems that by default the system will be unbootable.
It is also the case that if you move your RAID array or drives to another server that it will be unbootable, because dracut seems to only include modules needed for the curre........
If you plugin your phone to your computer and enable USB File Transfer/Allow on the phone side but the contents of your phone on the computer side are empty in the file manager, you probably don't have mtp-tools.MTP or media transfer protocol is the standard protocol that most phones use to communicate over USB to the computer.
Just do this to fix it and get access to your files:
apt install mtp-tools
After that you should be a........
In this example we install debian 10 with --variant=minbase which gives us a minimal/tiny install. Don't use variant if you want the full size install.
mkdir /tmp/deb10files
debootstrap --variant=minbase buster /tmp/deb10files/
Did you get an error?
debootstrap --variant=minbase buster /home/theuser/VMs/deb10files/
You'll get this error if you make a directory in your home........
You can read lots of posts about this issue but there is not much information about why this is the case or how grub determines the root= device name. Some even suggest modifying grub.cfg manually which is a disaster as the next kernel update will cause grub to revert back to the device name.
For most people this won't be an issue but those using template system, automated deployments and working in embedded may run into this issue with custom embedded and created minimal kernel........
Here is an easy way to restore things if you have the starting point and size of each partition using fdisk:
In this example we pretend that /dev/sda was wiped out, but the running system still has the info in /sys/class/block/sda
Go into each partition and record the "start" and "size"
hostdev@box /sys/class/block/sda/sda1 $ cat start
2048
hostdev@box /sys/class/block/sda/sd........
Remember that control connections are established on port 1723 and then actual data is transferred over GRE protocol 47.
If you have a NAT setup this will work without special forwarding or accepting of GRE packets (normally if you are not blocking outgoing connections and accepting established and related connections).
The below two commands will get things going so PPTP and GRE work
We first load the ip_nat_pptp module which allows PPTP to work with........
So say you happen to have 2 NICs of the exact same chipset, they will generally show up as the same name, with possibly a different revision in lspci. Normally this is not an issue if you have a server with 4 NICs, generally the eth0 to eth3 appears from left to the right (or right to left on some vendors) so it doesn't take much figuring out.
Generally if you have different chipsets for different NICs, it should be easy to know which one is eth0 or the first NIC in the OS.........
Later versions of ls try to be helpful and smart to prevent errors in dealing with files with spaces that were tradtionally a pain.
However if you need the raw/real filenames, this can break scripts or if you are pasting into a csv etc....
How do you make ls not add the quotes?
Add the capital "-N" switch
ls -N
You could also add an alias to make it more permanent
Do this to add it to ~/........
The easiest way for the current running kernel is:
update-initramfs -u -k `uname -r`
You could change -k to a specific kernel name if for some reason the current is not running (eg. if you are chrooted or in recovery mode).
If you want to update all kernels then use "-k all"
update-initramfs -k all -u
update-initramfs: Generating /boot/initrd.img-5.4.0-162-generic........
Sometimes due to your BIOS/EFI you may find that you have chosen "Energy Efficient" for your CPU which may effectively disable turbo mode. This is because "Energy Efficient" will often restrict or throttle your CPU to the base speed. This can impact nearly any CPU such as Intel's, AMDs, Opteron, Xeon etc...
This is of course frustrating, for example if you have a CPU that is 2.0GHz base speed but turbo to 2.5GHz, you will never hit more than 2GHz.........
PCIID 2357:0138
First install your kernel headers/source:
sudo apt install linux-headers-`uname -r`
1.) Clone this git repo
git clone https://github.com/morrownr/88x2bu-20210702
2.) Run the install
cd 88x2bu-20210702
./install-driver.sh
3.) Load the driver
mod........
You probably didn't do an "update-grub" and grub no longer has any proper menu entries, but before you can fix it let's try to get grub booting anyway.
If you get this lovely black grub screen here's how you can get things booting.
In my case I have a gpt partition with partition 1 and 2. Partion 1 is just my EFI / ESPand partion 2 /dev/sda2 is my root which includes /boot.
You will have to adjust this if you had a separate /boot partition.........
1.) Create your EFI/ESP Partition
If you happen to have some free space on the drive already then this is easy, just create a new partition of at least 100M.
The nice thing about the EFI spec is that it must just be in the first 2.2TB of space so for most users, it means you can simply resize the last partition(downsize it by 100M) and then add an EFI partition at the end.
For example if you had this partition scheme:
/dev/sda1 = /........
I've seen this bizarrely happen on a newly partitioned and custom installed Linux install, particularly if you did not properly unmount before rebooting.
You can find reports of it happening on various
How to fix the error: invalid arch-independent ELF magic.
You need to boot into Live/Rescue mode, chroot into your OS properly and then do a grub-install on each drive that nee........
To find which package a file is from just pass it the path to the file in question, whether it's a config file or binary, you'll find your answer (assuming it does belong to a package of course).
Just use dpkg -S /path/to/yourfile
How To Find Which Package The File Belongs To in Debian Mint Ubuntu Linux
eg.
dpkg -S /usr/bin/xed
xed: /usr/bin/xed
dpkg -S /etc/pam.conf
libpam-runtime........
This article about migrating to a CentOS 7 /8 RAID mdadm array has a lot of info but I wanted to focus specifically on what newer versions of CentOS 7 require to boot mdadm and what changes are necessary on CentOS 7.8+
CentOS 7 / 8 mdadm RAID booting requirements
This assumes you are chrooting into an existing install or using it to get a new deployment ready. However, these steps can........
Adding a default route is very simple with this command
Just replace 192.168.1.1 with the IPof your GW.
ip route add default via 192.168.1.1
How can you delete this default route if you messed it up?
It's just the opposite with "delete" instead of add
ip route del default via 192.168.1.1
This is the equivalent of the "route command's" route add default gw 192.168.1.1........
If you are getting this error from systemctl "Loaded: masked (Reason: Unit hostapd.service is masked.)" we need to unmask the service.
Solution
systemctl unmask hostapd
Removed /etc/systemd/system/hostapd.service.
It's fixed
root@routerOS:/var/log# systemctl start hostapd
root@routerOS:/var/log# systemctl status hostapd
● hostapd.service - Access point and authentication server for Wi-Fi and Ethern........
Just an FYI that the installer ignores your selection of Boot Loader, as it was intended for MBR/Legacy. The installer horribly, even when choosing "Something Else" and manually partitioning and creating an EFIin your install drive, will still install grub to the first EFI partition it finds, even if you are following a guide like this to avoid wiping out the M........
In this scenario, let's say you want to clone your OS at the filesystem level and the source system (the system you want to clone from) is in use.
Doing a blind rsync / is a big problem because it uses twice as much space for no reason.
The reason for this is that with ecryptfs you have a /home/.ecryptfs directory which has the actual encrypted versions of your files and folders. However your home directory (eg. /home/someuser) is mounted.
Doing the blind rsync will ca........
It may appear to be an Xorg or lightdm/gdm/mdm error but in reality for many users with this issue, it's a driver conflict and issue. I had a system that had two GPUs, an Intel and Nvidia GPU.
The only thing that got it working was to remove the nouveau driver and blacklist it so it never came back, then the Intel GPU works fine without these issues.
Solution
sudo rmmod nouveau
add nouveau/other driver to blacklist
edit th........
A quick fix is to run this command:
sudo brctl setageing br0 0
This causes the aging of the MAC address to time out immediately or in 0 seconds, which delete the entry frmo the FDB (Forwarding Database) and causes the error to go away. The default time is 300 seconds or 5 minutes.
You can also add it under your br0 definition like this in /etc/network/interfaces to make it permanent and automatic:
auto br........
Here is how Ifixed it on a Mint/Ubuntu install
1.) First download the latest AMDGPU-Pro driver from here:
https://www.amd.com/en/support
Navigate to your relevant video card:
2.) Download the installer
One issue is that by default they give you a version for the latest version of........
Is your /var/log/journal overweight and bloated? For example a decent install of Debian 11 with most applications and services ends up being about 4.9G with the journal taking a few gigs.
du -hs /var/log/journal/
1.3G /var/log/journal/
By default in a lot of distributions there is no maximum size so it will keep growing. This is especially problematic for embedded distributions and devices, but is also a huge waste of sp........
The easiest way for the 8821AU Realtek Wifi chipset / TP-Link T2U Plus:
Bus 002 Device 003: ID 2357:0120 TP-Link Archer T2U PLUS [RTL8821AU]
First install your kernel headers/source/other required tools:
sudo apt install linux-headers-`uname -r` make gcc bc
Clone this github repo with the driver:
git clone https://github.com/morrownr/8821au-20210708
Run the compile/ins........
Just use apt-cache policy to find the repo of a package:
apt-cache policy lxd
lxd:
Installed: 3.0.3-0ubuntu1~18.04.2
Candidate: 3.0.3-0ubuntu1~18.04.2
Version table:
*** 3.0.3-0ubuntu1~18.04.2 500
500 http://archive.ubuntu.com/ubuntu bionic-updates/main amd64 Packages
&nb........
One easy way is to use lspci -k like this:
sudo lspci -k|grep modules|sort -nr|uniq
Kernel modules: snd_hda_intel
Kernel modules: shpchp
Kernel modules: pata_acpi
Kernel modules: nvidiafb, nouveau, nvidia_drm, nvidia
Kernel modules: mei_me
Kernel modules: lpc_ich
Kernel module........
Sometimes manual intervention on various Linux system's, including Debian, is required to fix things after waking up from sleep.
One persistent issue is the sound system / pulseaudio needing to be reset and not working until you do that after waking up. It's not clear if it's an OS issue itself or the sound driver, but this will fix things.
Where do we put scripts or commands that need to be used upon wakeup automatically?
/lib/systemd/syst........
You just add on "non-free" at the end of each repo, like the example below:
If you wanted contributed packages then you could also add "non-free contrib" to each repo line.
Don't forget to do an "apt update" to see the new packages, this is especially handy for getting more drivers for devices with the firmware-linux-nonfr........
Debian based OS's have a similar issue as the behavior in RHEL/CentOS dhclient, which is that if you have an interface that relies on DHCP, if the first attempt fails, it will quit and stop. This is a problem especially if you are using your Linux as a router or something else mission critical, but where the internet for some reason may have been down or the DHCP server it gets a lease from broken.
The expected behavior you would hope is that when things are back online that the........
If you get an error like this when installing the Nvidia drivers:
WARNING: Unable to determine the path to install the libglvnd EGL vendor library config files. Check that you have pkg-config and the libglvnd development libraries installed, or specify a path with --glvnd-egl-config-path.
Just install these packages: &nbs........
Linux Mint offers an easy and painless upgrade path through the last 3 versions, which means no more reinstalling to stay current with the latest version.
The only catch is that you need the latest of each version, so for 18, you need 18.3 before you can go to 19, and then 19.3 (or latest), until you go to 20. However, it's really a small price to pay and on the machines we've tested, the upgrade went seamlessly each time (although sometimes video drivers/custom kernel modules l........
Bonding is an excellent way to get both increased redundancy and throughput. It is similar to the "Network Teaming" feature in Windows.
There are a few different modes but we will use mode 6, I think it's the best of both worlds, as it is not just a failover, but it provides round robin, so you will get redundancy and load balancing. So if you have a 1G single port, you will have a combined throughput of 4G at this point. Just bear in mind that the true thr........
This can be used on almost anything, since Gluster is a userspace tool, based on FUSE. This means that all Gluster appears as to any application is just a directory.
Applications don't need specific support for Gluster, so long as you can tell the application to use a certain directory for storage.
One application can be for redundant and scaled storage, including for within Docker and Kubernetes, LXC, Proxmox, OpenStack, etc or just your image/web/video files or even da........
This may be necessary if you have a VM or if for some reason you just want to be more efficient with your space and have the flexibility of changing your swap space at will.
What we mean is the ability to use a "swap file" or similar to the Windows "pagefile" that normally resides on the root or c: partition of Windows.
Here's all you have to do and then you to can have a single partiton with everything, including the swap file on the root partition if you........
The Best Docker Tutorial for Beginners
We quickly explain the basic Docker concepts and show you how to do the most common tasks from starting your first container, to making custom images, a Docker Swarm Cluster Tutorial, docker compose and Docker buildfiles.........
Just click on the Start Menu and go to "Startup Applications"
Then click on the "Add"Button
Now enter the command we need to open the folder/directory automatically using the filemanager
For remote SSH host (you need pub key auth for it to open without a pa........
This was done on Mint 20 but works the same on nearly any new Linux, but is only recommended for people comfortable or familiar with Linux. This method will work on almost all versions of Windows from NT, 2000, 2003 Server, 2008 Server, 2012 Server, 2016 Server, 2019 Server, 2022 Server, XP, Vista, 7, 8, 10 and 11.
However, if you want the easiest solution to........
Why choose OpenVPN instead of a firewall appliance?
OpenVPN can be a reliable and easy replacement for traditional hardware or just be an additional tool that your company uses so that the firewall can focus on its job rather than acting as a VPNappliance at the same time.
When comparing OpenVPN with traditional firewal........
How To Install Wazuh Server / Quickest Installation
Wazuh (forked from the well known OSSEC project) is a full SIEM (Security Information Event Management) that works extremely well with the platforms it natively supports as an "Agent", which allows you to do scans of everything such as all processes running, CVE vulnerability check, incident reporting etc...
Prerequisites:
A lot of issues with Wazuh seem to be caused by i........
If you get an error that you aren't in the sudoers file, this typically means that your user is not designated as an admin with sudo privileges.
In plain English, when it comes to some OS's like Debian including 10,11 etc.., by default the user is created without special privileges which is contrary to how Ubuntu/Mint handle the secondary user.
Let's check the sudoers file to see the problem.........
A lot of newer installs will automatically prohibit the root user from logging in directly, for security reasons or they will only allow key based access.
If you know what you are doing/don't care about security or have an incredibly secure password for testing, then you can enable it.
Edit this file: /etc/ssh/sshd_config
Find the following line: PermitRootLogin
Set it like this:
PermitRootLogin yes
Now rest........
1. Let's work from an environment where we can install Ansible on.
If you are using an older version of Linux based on Mint 18 or Ubuntu 16, you may want to get the PPA and get the latest version of Ansible that way:
sudo apt install gpg
sudo add-apt-repository ppa:ansible/ansible
sudo apt update........
Volume control will often stop working, if your sound server (normally pulseaudio) dies or restarts whether by itself or by you. The reason pulseaudio may need to be restarted is due to some sort of crash or other issue that prevents sound from working (normally restarting or doing a killall pulseaudio fixes things).
However, you will normally find at least in OS's like Ubuntu/Mint 16/18+ that you cannot control the volume whether adjusting the level, changing input/outputs and........
In newer of versions of Virtualbox, especially above 6.0 (eg. 6.1 like the example below), a lot of times the "Enable Nested VT-x/AMD-V".
If you are having this issue, you will see the option is grayed out. It doesn't mean that your computer does not support virtualization, although it is possible it is disabled in the BIOS. You can verify........
NAT Network, the VMs can communicate but your host cannot access them by default.
NAT VMs have internet but cannot communicate with each other.
Bridged is simple and allows full LAN access as if you had a physical machine plugged in but is often bad for testing, work or corporate environments and is not very portable when it comes to moving your VMs to other locations and networks.
Here is how you can use NAT Ne........
From the terminal do this:
cat /proc/cpuinfo|grep -E "svm|vmx"
You should get output like this(svm = AMD-v and vmx=Intel-VTx):
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc cpuid aperfmperf pni pclmulqd........
zip is useful to share files across multiple platforms.
A simple way if you want to zip all pdfs:
zip Labs.zip *.pdf
If you want to zip everything in the current directory and subdirectories do this:
zip -r stuff.zip *........
The Linux Mint team has disabled it by setting an apt preference, you can edit or just remove the file:
sudo apt install snapd
Reading package lists... Done
Building dependency tree
Reading state information... Done
Package snapd is not available, but is referred to by another package.
This may mean that the package is missing, has been obsoleted, or
is only available from another source........
Just install these packages and restart the VM:
1.) Enable guest-utils on the host side:
sudo apt install virtualbox-guest-utils virtualbox-guest-x11
2.) Enable guest editions on the VMside
This must be done for each VM that you want to have the guest additons for accelerated GPU performance and for drag and drop/clipboard sharing
First insert the Guest Addtions CD image........
Kubernetes Easy Beginners Tutorial/Architecture Guide
Kubernetes is known as container orchestration and we should start at explaining the container part of it.
A Container is what runs the actual application and based on an Image, and are more comparable to something like an LXC Container, Virtuozzo/OpenVZ using the Linux Kernel Namespaces feature. Containers run these images as independent, isolated operating environments under the O........
There aren't too many simple guides that show you how to use commands to setup your USB or other drive as a normal bootable drive where you can easily boot custom kernels or whatever OS you would like.
1. Get the tools we need:
We install "syslinux" for MBR and "syslinux-efi" for EFI and "MBR" as we need a tool that embeds the actual MBR into our USB:
sudo apt install syslinux syslinux-efi mbr........
It has been renamed to kde-spectacle so you install it like so:
sudo apt install kde-spectacle
You'll find it in your start menu listed as "Take Screenshot"........
Just edit your ~/.bashrc and add this at the very end:
export PS1="realtechtalk.com"
Then your prompt will look like this:
bladeblox:uptime
08:47:14 up 48 min, 1 user, load average: 1.00, 1.07, 0.96
If you wanted a dollar sign at the end then you would change it like this:
export PS1=&........
So you're trying to browse to a properly configured Samba share but you get this error:
Unable to mount location
Failed to retrieve share list from server: Connection timed out
If your config is right, it can be due to a protocol miss-match where your client has not enabled SMB3 but by default the other side (server) has enabled it.
You can test this out to see with the smbclient tool........
This is a common issue when e-mailing or uploading video files.
One note is that you should make the filesize you choose below about 20% smaller than you need. For example I took a 219MB video and told it to be 20M. The resulting file was still about 21.9M but it was OK when I said 18M and was barely below the 20M size.
ffmpeg is our friend here, just use this command:
Change the -fs 100Mto the size you want eg. 20M, 500M
Chan........
If you are using the stock 5.4 kernel this is normal but I can confirm it is fixed in newer 5.8 kernels.
To fix it just install the 5.8 kernel and reboot:
sudo apt install linux-headers-5.8.0-64-generic linux-modules-extra-5.8.0-64-generic linux-image-5.8.0-64-generic........
Usually if you get the grub boot loader and it doesn't show any boot options, it's because grub was not installed correctly and/or the partition that it is supposed to be on has changed or does not exist. It can also happen if you install Linux to one drive, but the boot loader to another by accident, whether EFI or MBR/Legacy mode.
You can normally fix your booting/bootloader/MBR/EFI it by chrooting into your root partition:
#become root
sudo su........
Just a quick note and warning is that if you are testing to see if EFIPXE booting works on a VM, MAKE SURE it actually works. For example Iinitially tested using my Distro's QEMU 2.5+dfsg-5ubuntu10.46 and ovmf BIOS firmware (OVMF supports EFI). However, I found on old versions of QEMU (like 2.5), EFIbooting with GRUB NEVER works so it may appear that you have made a mistake when everything is fine when you boot a physi........
Traditionally kernels were numbered starting from 0 but by default the "new style" of grub boot loading considers each subkernel item to be different so if you have 3 entries for 4.40-148 rather than counting for 1.
To get the expected behavior let's show this example and how we can boot it
We do a grep on menuentry in /boot/grub/grub.cfg to see all of the bootable kernels rather than scrolling through loads of extra entries we don't care about (thou........
It seems that QEMU/KVM's default PS2 mouse and keyboard doesn't work right in most cases. I have especially observed issues using Ctrl+C and Ctrl+V and in Linux you may see repeated key presses in the terminal and you will wonder why you copied something and it's not in the clipboard when you try to paste. The way to temporarily fix it is to press the key that is repeating once(works in Linux but not really in Windows).
Sometimes when moving your mouse it will also s........
One simple flag to configure will create a makefile that statically links all the shared objects and embeds them instead the binary execute. This means as long as you have the same architecture that things should run.
Eg. if you have an old version of Debian with a different version of glibc, then this will solve that problem.
./configure LDFLAGS="-static"
To test that it is really statically linked run ldd:
ldd src/wget........
If you get this error, you were probably compiling some sort of binary or package and got this error. It is normally solved by installing the "gettext"package.
On Debian/Ubuntu just apt-get it:
apt-get install gettext
After that you should be able to configure and make (compile) properly.........
Many people may not be aware that you can turn commodity hardware into a Mikrotik OS and there are various options which is "CHR" (Cloud Hosted Router) which is a VMimage meant for Virtualization only (seriously, I've tried to dd the image to a physical server and it just crashed as it does not contain any drivers for physical).
One note as well if you are trying to do a baremetal install you may get an error "Error Loading Operating System" or........
The problem seems to be that whatever kernel and initrd you have is tied to an old version of CentOS 7 that is no longer in the current repos of most mirrors.
If you were previously able to PXEboot and install CentOS and you are sure your network and tftp are good the problem is that you have an outdated kernel and initramfs that point to a defunct version.........
To disable selinux temporarily and immediately:
setenforce 0
To make it permanent edit /etc/selinux/config:
vi /etc/selinux/config........
Teams for Linux is horribly broken, especially because the calendar doesn't show any meetings so unless you are in the right Team and Channel at the right time, you cannot join your meeting or know there is one.
As you can see there is an orange bar to represent the meeting but you cannot click it or it makes a new meeting. For some reason this bug is only present in the Linux app but not in the Android App or from the web calendar.
This is a horrible design flaw that ca........
I have a Canon MF642c and the scanner wouldn't work. I tried to use saned but it didn't work with the BJNPlike it did for some other Canon models.
Introducing sane-airscan with packages for the most common distributions: https://software.opensuse.org/download.html?project=home%3Apzz&package=sane-airscan
http........
It took a lot of fiddling to make a Huion Kamvas 13 Pro work in Linux but it simple once you know what to do. Don't bother searching as it is unlkely there is a guide out there that will actually make your tablet work.
It mainly comes down to the fact that the hid_uclogic kernel module is buggy or doesn't support MANYof these wacom based/Huion tablets properly.
What was happening with me is that Ihad the Kamvas 13 Huion setup as a secondary screen/monitor.&nb........
When you automount a drive in /etc/fstab even if it's not important like an external drive that you only use sometimes and is not required for booting, it will prevent a successfuly boot.
If you disable quiet mode for booting you will see something like below "A start job is running for dev-disk ...."
How do we fix an fstab entry from preventi........
A very common use case is that you don't want to waste time using a video editor that requires you to open it up and manually import the video clip and audio clip, then manually delete the old audio track and import the video and new audio. That's too much work and time since we don't want to go through the hassle.
ffmpeg is our solution, all we have to do is specify 3 variables and we're done!
-i Windows2019-Server-Noaudio.mp4 is our in........
The problem is that Linux uses UTC and Windows uses the local time from the RTC. This means whenever you boot Linux or Windows and then go back to the other OS, you will find your time is incorrect because of the two different clock modes fighting.
This results in very annoying issues when booting between the two because the clock is set based on the different standards once you boot (eg. Linux UTC by default and Windows RTC). For example it may cause issues with fsck and........
This tutorial will get your router up and running using emulation tools. In this case we'll be getting a Cisco C7206 (C7200 series) VXR router going which also supports SCCP VOIP services.
dynamips is the emulator itself and dynagen is the front-end tool that helps us control everything. It is used by tools such as gns3 and eve-ng.
Together the two tools (dynamips and dynagen) allow us to create and emulate REAL router........
The best way to avoid this problem is to understand how your BIOS is setup to boot.
Often newer machines will default to U(EFI) which is different than the traditional MBR/Legacy mode.
The problem is that this may not be apparent, often a BIOS Boot Menu will show a Legacy Boot Option and EFIOption without defining it.
A good example of this is if your USB is called "Kingston" you may see in your Boot Menu "Kingston" and also "Ubuntu"........
This assumes your system is a fresh and normally working install.
What often happens is that many new devices have multiple audio outputs which are generally analog and HDMI/Digital out. Sometimes the OS defaults to the wrong one that you didn't want.
For example if your sound is supposed to play over the HDMI, perhaps the output is set to analog or vice versa.........
This happens to a lot of Nvidia users especially users of newer cards like the RTX series. If for example you are trying to boot and install Linux and you get a black and white grub2 screen instead of a nice graphical welcome installer, you probably suffer from this bug. It is normally followed by the user booting and finding they just have a blank/black screen.
Here is the quick flow of steps to fix it:
If you get a black grub scree........
Before you try to install and dual boot it is very important to understand the concept of "what boot mode your BIOS is in" and "what mode you booted the installer to".
Then follow the example of Linux Mint (but most Linux installers are very similar)to carefully understand WHERE you are installing your Boot Loader to whether that be MBR or EFI.
How Am IBooted?
First it's important to check your BIOS to see........
In QEMU 4 or higher you can no longer use the normal "-soundhw ac97" flag and it is much more complicated but here is a simple copy and paste on Linux that will just work:
-audiodev you have to use -audiodev to specify the driver and id
driver=pa
id=someid
-device you have to specify the same audiodev id you used in -audiodev and driver
-audiodev driver=pa,id=pa1 -devic........
It really seems limited in that it can mainly give you the things you would see on the physical unit such as load etc..
wget https://downloads.sourceforge.net/project/apcupsd/apcupsd%20-%20Stable/3.14.14/apcupsd-3.14.14.tar.gz?r=https%3A%2F%2Fsourceforge.net%2Fprojects%2Fapcupsd%2Ffiles%2Flatest%2Fdownload&ts=1598115866
tar -zxvf apcupsd-3.14.14.tar.gz
cd apcupsd-3.14.14
[root@somebox apcupsd-3.14.14]#
./conf........
If you've come here, don't be embarraassed, working in IT, this is the MOST common computer problem that almost everyone will encounter. The reason why I'm doing this post is because I've seen an increase from colleagues and admins having this problem and many times it's not even your fault. A common scenario is that someone acquires a new or used computer which they weren't given the password for. Fortunately Ihave a detailed list of all the options whether free or pa........
This seems to happen on most if not all Nvidia cards but the good news is that if you are using any of the Linux drivers and have the nvidia-settings tool installed it is just a simple command.
Solution:
nvidia-settings --assign CurrentMetaMode="nvidia-auto-select +0+0 { ForceFullCompositionPipeline = On }"
Enter the above command in your terminal and the screentearing will be fixed which is like enabling Tear Free on AMD cards.&........
I was using a small box as a router and one of the ports started going off and coming back at 100M. I truly believe it is simply that it was a case of overheating. Although CPUtemps were only about 67 degrees, the physical box itself was almost burning hot. Isolved the cooling issue and never had the issue again.
Jul 28 15:09:27 swithbox kernel: e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
Jul 28 15:09:28 swithbox kernel:........
This is very frustrating but the fix is usually easy once you read this blog. It's very frustrating when you find that your Linux / Ubuntu laptop's wifi will NEVER work unless it is plugged into the power. The wifi menu may say "Wifi disabled by hardware switch". You may find that your laptop has no switch or has a function wifi button on the keyboard but this does not work or have any effect.
The cause is usual a "wmi" kernel module and simply doing an........
apt install software-properties-common
add-apt-repository ppa:deadsnakes/ppa
apt update
apt install python3-pip
apt install python3.7 curl gnupg python3.7-dev git
ln -s /usr/bin/python3.7 /usr/bin/python3
pip3 install numpy keras_preprocessing
curl https://bazel.build/bazel-release.pub.gpg | sudo apt-key add -
echo "deb [arch=amd64] http://storage.googleapis.com/bazel-apt stable jdk1.8" | sudo tee /etc/apt/sources.list.d/bazel........
Most newer distros inexplicably cause your NIC to have what Icall "random" non-standard name conventions because of systemd.
This is a big problem for many people and especially those running servers. Imagine that you have a static IPconfigured for ens33 but then the hard disk is moved to a newer system, the NIC could be anything from ens33 to enp0s1, meaning that manual intervention is required to go and update the NIC config file (eg. /etc/network/interfa........
Just run this apt install command
sudo apt install pepperflashplugin-nonfree browser-plugin-freshplayer-pepperflash
After this restart your browser and check Adobe's site to verify if your Pepper flash is working and showing at least version 32.
https://helpx.adobe.com/flash-player.html
As you'll see below it will download the latest version which is currently 32 and this was not possible with the old/crappy deprecated adobe-flash plu........
I used to believe that for Desktops especially that the "ondemand" CPUfrequency changing that kernels included with Ubuntu and Debian based distros have would be sufficient for snappy performance.
However, you can feel the lack of performance on the fastest computer if you have ondemand. A lot of times even under high load 100% of your CPUfrequency in MHz will not be used.
For example a 2.8Ghz CPUmay only run at 1.8MHz or even .9GHz. Now........
radeon_dp_aux_transfer_native: 158 callbacks suppressed
The simple answer is that radeon driver sucks and is a remnant of typical AMD/ATI issues.
Use AMDGPUif you support it:........
It's as simple as below where you just specify the dev device of the CDROM which is usually /dev/sr0. You can boot actual bootable discs like Windows, Linux, etc straight from a physical drive this way.
sudo qemu-system-x86_64 -cdrom /dev/sr0 -m 4096
........
There are a few caveats that may not be obvious to everyone so I am going to cover them here but keep this in mind before starting.
Before starting install epel or you will be missing tesseract:
yum -y install epel-release
#1) When you specify your SSL certificate with a full path, it really needs to exist where you tell it to (including the default location of /etc/ssl/certs and /etc/ssl/c........
If you've ever gotten errors like this the solution is simple, you need i386 enabled on your 64-bit install because wine depends on some 32-bit x86 libraries:
dpkg --add-architecture i386
apt update
apt install wine
After that it will install just fine.
apt install wine
Reading package lists... Done
Building dependency tree
Reading state information... Done........
This is sure simple if you follow the guide but it took a lot of hacking around to make this work on Debian/Ubuntu!
Now before you ask why bother running wine and python, the reason is because Python executables are NOT cross-platform. If you run pyinstaller in Linux, that binary will only run on Linux and the same if you do it in Windows. So it is preferable if you have a single environment that you can create Linux and Windows binaries from rather than running 2 separate........
sudo usermod -a -G groupname username
It's really simple like above, the -a is for append so that you are not changing their main group, but adding them to another additonal group. Just change "groupname" to your group and "username" to the user you want to be added to "groupname".
A common task these days is getting your user access to kvm for virtualization so the KVM/QEMUprocess........
This is only really necessary in the case you don't want DHCP. If you are dealing with an encrypted LUKS server on the internet, you will often want to have a static IP so you know which IP to connect to (or if you have a semi-static IP assigned by DHCP).
SET IP Address by /etc/initramfs-tools/initramfs.conf
IP Address=192.168.1.27
Gateway=192.168.1.1
Subnet Mask: 255.255.255.0
Hostname=myhome.com
IP=192.1........
The reason for doing this is that the installer doesn't seem to work properly for LUKS and the server installer doesn't even support LUKS anymore. When you use the GUI install on Desktop for LUKS it won't boot and will just hang after you enter your password. So the only reliable way is to do it ourselves.
1.) Make a default minimal install of Ubuntu
2.) Have a secondary disk on the server or VM.
3.)........
The cool thing here is that we only need 1 drive to make a RAID 10 or RAID 1 array, we just tell the Linux mdadm utility that the other drive is "missing" and we can then add our original drive to the array after booting into our new RAID array.
Step#1 Install tools we need
yum -y install mdadm rsync
Step #2 Create your partitions on the drive that will be our RAID array
Here I assume it is /dev........
sudo vi /etc/lightdm/lightdm.conf.d/70-linuxmint.conf
Change this:
[SeatDefaults]
user-session=mate
allow-guest=false
To this:
[SeatDefaults]
user-session=mate
allow-guest=false
greeter-hide-users=true
greeter-show-manual-login=true
To see and apply your changes just restart light........
To enable amdgpu we have to set special kernel boot parameters. The easiest way is to make it permanent and apply to all kernels (no messing around with grub.cfg) so we'll edit those defaults in /etc/default/grub by changing the GRUB_CMDLINE_LINUX_DEFAULT parameter. After that don't forget to run "update-grub"to apply it (otherwise amdgpu will never be enabled).
The opensource driver for AMD is really quite impressive these days, as we show it works with ve........
It is fairly simple to use once you know how to use it. However, the tricky thing is that by default it doesn't seem to be active or listen on any interface on manually specified.
How To Install ifplugd
First we install ifplugd
sudo apt install ifplugd
Let's enable it on our desired device(s)
vi /etc/default/ifplugd
set this line as so:........
The reason we use the command below is because we need the md5sum value hash of the password. This means that we cannot use the md5sum
Change "yournewpass" to the pass you want to set
echo -n "yournewpass" | md5sum
Then you get the md5sum hash of whatever you entered eg. in this case "yournewpass"
5a9351ed00c7d484486c571e7a78c913 ........
I find that the default settings for the radeon driver that is applied to most AMD cards is horrible. For example by default TearFree is not enabled and it causes videos to have some kind of square artifacts.
Here are the settings I have found most suitable for AMD cards:
You need to create file in the following path and restart Xorg or your computer to apply it:
*Beware that making a mistake here will possibly make your computer........
This problem has been around forever, Linux seems to think it is fine to use the r8169 driver for an r8168 NIC but this often causes problems including the link not working at all.
In my case ethttool shows the link up and detected but it simply does not work especially on a laptop that has been resumed from suspension. Sometimes it takes several minutes for it to work or to unplug and replug the ethernet.
Here is the solution:
Install th........
You need to disable vsync like this when running glxgears:
vblank_mode=0 glxgears
For Nvidia drivers do this:
__GL_SYNC_TO_VBLANK=0 glxgears
Notice the higher than 59-60 fps results with vblank_mode=0:
ATTENTION: default value of option vblank_mode overridden by environment.
7919 frames in 5.0 seconds = 1583.704 FPS
8187 frames in 5.0 seconds = 1637.266 FPS........
Downloading and compiling from source to get the latest version of Asterisk is really simple with this guide.
apt install gcc make g++ libedit-dev uuid-dev libjansson-dev apt install libxml2-dev sqlite3 libsqlite3-dev
wget http://downloads.asterisk.org/pub/telephony/asterisk/asterisk-16-current.tar.gz
tar -zxvf asterisk-16-current.tar.gz
cd asterisk-16.6.2/
./configure
If you get this error change y........
Use fdisk on your USB drive to create a bootable NTFS partition (in my case /dev/sdb):
sudo fdisk /dev/sdb
Welcome to fdisk (util-linux 2.27.1).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Command (m for help): n
Partition type
p primary (0 primary, 0 extended, 4 free)........
There are many ways but a favorite way is to boot any Linux LiveCD and to use the syslinux package like so:
Just change the "sdx" to your sd for example /dev/sda or whatever the drive is that is supposed to boot Windows.
sudo dd if=/usr/lib/syslinux/mbr/mbr.bin of=/dev/sdx
0+1 records in
0+1 records out
440 bytes copied, 0.0197808 s, 22.2 kB/s........
If you are using the default "Image Viewer" aka Xviewer it seems to die on very large resolution files. It seems to understand to scale them but the printer will try to print and then fail.
Using "Pix" viewer seems to fix this and causes these larger files to print just fine.
........
If you can print other PDFs but not a particular one it is very likely that the PDF size is A4 (the longer, skinnier Asian paper size) instead of the North American letter size ( 8.5" x 11"). This breaks printing in most cases. Or it may print if you find a program that ignores the size issue.
Here is an example of an A4 being rejected by a printer in Ubuntu Linux via CUPS
Cannot print PDF CUPS Samsung C460:
Processin........
This is all controlled by /etc/issue
You can basically enter anything in there that you like, but there are preset variables that are mentioned at the end of the page that discuss this.
Some examples of /etc/issue:
Centos 7:
S
Kernel r on an m
Ubuntu 16.04:
Ubuntu 16.04.6 LTS n l
You can also insert any of t........
Just edit your tftp file for xinetd like this:
*Change the IPto be the IPof the interface you want to listen on.
To test if your tftp is available on a certain IP range use nc -u yourip 69 to see if you can still connect (/var/log/messages or /var/log/syslog) should show the connection if it is open.
Oct 13 23:20:34 01 xinetd[26631]: Started working: 1 available servic........
service sshd status
● ssh.service - OpenBSD Secure Shell server
Loaded: loaded (/lib/systemd/system/ssh.service; enabled; vendor preset: enabled)
Active: failed (Result: start-limit-hit) since Wed 2019-10-02 11:07:54 EDT; 36s ago
Process: 476 ExecStartPre=/usr/sbin/sshd -t (code=exited, status=255)
Oct 02 11:07:54 box systemd[1]: Failed to start OpenBSD Secure Shell server.
Oct 02 11:07:54 box sys........
This often happens if you are adding a secondary route, especially with Linux source based routing.
ip route add default via 10.10.10.254 table 10
RTNETLINK answers: Network is unreachable
If that happens you will probably find that it is unreachable because your NIC does not have an IP in the 10.10.10.0/24 range so just assign an IP in that range to your NIC and try again.
eg. ifconfig eth0 10.10.10.254 netmask 255.255.255.0 up........
In Centos 7 tftpd will not work with selinux. Clients will not be able to connect and this is all you'll see in the log (then nothing more):
Sep 18 14:39:15 localhost xinetd[4327]: START: tftp pid=4331 from=192.168.1.65
On the client/computer side you will see this:
TFTP.
PXE-M0F: Exiting Intel Boot Agent
Basically the client is being instantly connected and bloc........
By default your DHCP will often not work because it is not listening on any interfaces.
All you have to do is edit this file:
vi /etc/default/isc-dhcp-server
then find the "INTERFACES" line and add each interface that should listen:
INTERFACES="br0 enp0s10"
........
I think this is more so an issue with kernel modules not being included. I had this issue on Linux Mint because a new kernel I upgraded to DIDNOT have the "extra" modules and part of that reason is also because older kernels are named differently than new ones.
Take this example article below that shows it in action.
If you were previously........
I don't consider a lot of these "extra" kernel modules "nice to have" as they often contain drivers for essential items like your soundcard, your NIC and many other devices that may not work. Sometimes you may find that "sound" or "ethernet" worked before a kernel/OS upgrade and now in the new version they don't. Often it will be because you need to install the "extra" kernel modules.
One other weird thing is that sometimes........
If you've just installed VBox and it is not starting or working, the most common problem is usually that you don't have your kernel source installed, which means there is no kernel driver for vbox so it can't work.
You may get an error that says "Kernel driver not installed" in your Virtualbox.
So the first thing you should do is install your kernel source by running this:
sudo apt-get install linux-headers-`uname -r`........
The way of doing it in mint is different than gnome and ubuntu.
gsettings set org.mate.background picture-filename /path/to/file.jpg
*If you try to use the gnome way it will NOT work with Linux Mint:
gsettings set org.gnome.desktop.background picture-uri /some/pic.jpg........
This is a security hole in my opinion and should be plugged by editing the lock screen ui layout:
vi /usr/share/mate-screensaver/lock-dialog-default.ui
#find these objects and set the visible property to false
object class="GtkLabel" id="note-tab-label"
object class="GtkLabel" id="auth-username-label>
object class="GtkLabel" id="auth-realname-label"........
By default printscreen or alt print screen will get the whole desktop or the application in focus, respectively. But what if you want to select a portion of the screen?
gnome-screenshot:
ksnapshot
compiz
This is a nicely integrated solution
sudo apt-get install compizconfig-s........
Click "Administration" ->"Login Window"........
If you get error messages like this it is usually because /var/run/sshd does not exist.
root@userbox:/# service sshd status
● ssh.service - OpenBSD Secure Shell server
Loaded: loaded (/lib/systemd/system/ssh.service; enabled; vendor preset: enab
Active: failed (Result: start-limit-hit) since Wed 2019-04-10 02:24:44 EDT; 1
Process: 511 ExecStartPre=/usr/sbin/sshd -t (code=exited, status=255)........
I have seen this in a few rare cases after a reboot, where all folders and files will have the Read Only Attribute. If you uncheck it, it will just come back. It is more of a filesystem issue in Windows than a configuration issue and it looks like when Windows detects a badly corrupted filesystem that it will make things read-only, sort of like Linux would.
If you are Administrator or the owner of the folder and this is happening it is probably due to the reasoning mention........
The strange thing is that usually the first install or two will work on any new machine but then it suddenly won't. I had this experience on QEMU 2.13 on a different machine. There is something finicky or buggy about the CUCM installer even when choosing the same virtual hardware specs.
qemu-kvm command:
/usr/libexec/qemu-kvm -version
QEMU PC emulator version 0.12.1 (qemu-kvm-0.12.1.2-2.506.el6_10.1), Copyright (c) 2003-2008 Fabrice Bellard
........
It is much more useful to have meaningful and detailed logging from tftp to see what is or isn't happening especially for VOIPand other embedded device appications:
Edit the file:
vi /etc/xinetd.d/tftp
Change the server line like this:
server_args = -s /var/lib/tftpboot........
This will find all tap devices and try deleting all of them. Of course don't run this if there is a chance an unused tap device is necessary and would not be created by the script ro application using it.
for tap in `ifconfig -a|grep tap[0-255]|awk '{print $1}'`; do
tunctl -d $tap
done........
Pass QEMU this flag:
-soundhw ac97
Or you could use (for a Ensoniq soundcard):
-soundhw es1370
However on some machines I get this error:
pulseaudio: pa_simple_new for capture failed
pulseaudio: Reason: Connection terminated
pulseaudio: pa_simple_new for capture failed
pulseaudio: Reason: Connection terminated
audio: Failed to create voice `ac9........
This is the closest way to disabling it without using the "libata.force=noncq" kernel boot option is to set the queue to a depth of 1 which doesn't actually disable it.
Change the sdc below to match the device you want to disable NCQ for.
[root@officebox ~]# echo "1" > /sys/block/sdc/device/queue_depth
Errors that indicate you are having a performance issue are these in messages or dmesg relating to N........
If you visit a site that exploits the WebRTC vulnerability including whatismyipaddress.com it may show "Local IP Address" which would be the real IP of your machine.
The vulnerability works on Windows and Linux machines (contrary to false information on the web which claims it only affects Windows).
The above works and happens even if you are using a proxy or VPNaccount like ProVPNAccounts.com
It is easy........
chroot which stands for change root allows you to virtually operate in another operating system even though you haven't booted it. It is commonly used to deploy new distros, applications and to fix a broken Linux/Unix install or prep a new system image without having to physically boot the drive or disk.
So in this example let's say we have a drive that has a Linux OS installed on /dev/sdb1 and we have mounted this partition on /mnt/sdb1
The key point is to edit the &quo........
This is a common issue that I haven't seen many answers for on the internet. When you are using Linux as your host machine and you are connecting to another Linux machine over VNC you CANNOT use Ctrl+Alt+F1 to change virtual consoles as it sends the keys to your actual local machine.
In many versions of Linux you can cycle through virtual terminals including over VNC using this:
Alt + Left Arrow or Alt + Right Arrow
This........
Uh oh, so you're working on some super l33t code or other stuff that is super important and Linux Mint's MATE or Cinnamon window manager freezes. This means maybe you can move your mouse but you can't click anything, you can't Alt + Tab to another program but everything appears to be working other than that.
The first thing you would do is Ctrl + Alt + F1 (or whatever virtual terminal you want) and get into the Linux bash prompt (the black screen where things really happen :))........
Perhaps you've just seen this in the bash prompt:
-bash-4.1#
Instead of the expected user@hostname#
It is probably because you are missing .bash_profile or .bashrc in your home directory
Check for yourself:
ls -al ~/|grep -E ".bash_profile|.bashrc"
-rw-r--r--. 1 root root&nbs........
for ip in `netstat -nt|awk '{ print $5 }'|cut -d ":" -f 1|tail -n +3|sort|uniq`; do
echo $ip;whois $ip|grep -i netname;echo "---------------------------"
done
77.88.47.40
netname: YANDEX-77-88-47
---------------------------
40.77.167.5
------........
The key thing is that you must use a "machine"id of "pc-1.3" or it will say your hardware is not supported.
Additionally you MUST use a virtio disk or you will get a ks_pre.sh error as soon as the install starts (a look at logs will show it can't find a disk). This is funny because even though the OS finds the disk and an fdisk -l shows it, it looks like the script looks for a /dev/vda device (virtio) and nothing else, so if you didn't use Virtio as you........
ln -s --force newfile.jpg existingsymlink.jpg
All you do is use the --force flag to force/update the existing one.
The above modifies a symlink called "existingsymlink.jpg" and points it to "newfile.jpg" as the source.........
It was broken because of this package for xorg I installed:
xserver-xorg-core-hwe-18.04
Just remove it even if you have to chroot from a live USB/CD:
sudo apt-get remove xserver-xorg-core-hwe-18.04........
The key thing here is to know the actual partition that is encrypted.
Often in Linux Mint's installer that ends up being partition 5 or /dev/sda5
sudo cryptsetup luksOpen /dev/sda5 anynamehere
You will then be prompted for your irrecoverable passphrase:
Enter passphrase for /dev/sda5:
If all goes well it won't say anything further. If it says ""No key available with this passphr........
This is not about systemd/systemctl and not about "onboot" so there's no rc.local trick here but it's the GUI/Gnome etc when a user logs in that a command is launched.
Put this in your home dir
The .config/autostart directory is where Linux Mint/Ubuntu checks for autostart application config files
mkdir -p ~/.config/autostart
Create a new entry/file that starts an application........
If you see this in /etc/sudoers it is NOT a comment but an include.
#includedir /etc/sudoers.d
For example in Linux mint sudoers.d contains the following files:
casper mintupdate README
casper for example contains the following sudoers line:
mint ALL=(ALL) NOPASSWD: ALL
So if you are messing ar........
Jan 30 17:16:10 localhost sshd[25385]: error: Failed to allocate internet-domain X11 display socket.
The solution for me on the server side was the following in sshd_config:
AddressFamily inet
*Remember to restart sshd and also reconnect from the client side.
Ihad all the normal X11 settings on the server but it just stopped........
Whether you are at work, at the coffee shop or on the public internet here are some basic but effective rules for iptables that lock things down (eg. no one can SMB or SSH to you or really anything):
# Generated by iptables-save v1.4.21 on Fri Dec 14 14:00:08 2018
*nat
:PREROUTING ACCEPT [160:19844]
:INPUT ACCEPT [4:357]
:OUTPUT ACCEPT [2955:182236]
:POSTROUTING ACCEPT [2955:182236]
COMMIT
# Completed on Fri Dec 14........
size = the amount of RAM (m for megabytes)
/mnt/ram = the mount location of the ram disk (change to the path you want it mounted to)
mount -t tmpfs -o size=4096m tmpfs /mnt/ram/
Example test in an old server:
You can see that when reading if you don't specify bs1=M the read speeds are several times slower (eg. 450MB/s vs 2.1GB/s)
mount -t tmpfs -o size=4096m tmpfs /mnt/ram/^C
root@testserver:~# dd........
iw dev wlan0 station dump
This is very useful because it is helpful if you are running something like hostapd and need to see the signal strength and negotiated connection speed.
Station ff:ff:ff:ff:ff:ff (on wlan0)
inactive time: 16309 ms
rx bytes: 25451
rx packets: 325
tx bytes: 44381
tx packets: 159
tx retries: 0
tx failed: 0
signal: -72 [-72] dBm
signal avg: -72 [-72] dBm........
This should apply to most Linux distributions just incase you get into trouble or wipe out the defaults by accident.
/etc/iproute2/rt_tables
#
# reserved values
#
255 local
254 main
253 default
0 unspec
#
# local
#
#1 inr.ruhep........
Just find the relevant file in /etc/NetworkManager/system-connections
sudo vi /etc/NetworkManager/system-connections/Wired connection 1
[802-3-ethernet]
duplex=full
mac-address=00:00:00:FE:FE:FE
[connection]
id=Wired connection 1
type=802-3-ethernet
timestamp=1532403341
[ipv6]
method=ignore
[ipv4]
method=manual........
Set this in /etc/sysctl.conf
net.ipv6.conf.all.disable_ipv6 = 1
#apply the settings
sudo sysctl -p
........
growisofs -Z /dev/sr0 critical.tar.gz.gpg
Executing 'genisoimage critical.tar.gz.gpg | builtin_dd of=/dev/sr0 obs=32k seek=0'
I: -input-charset not specified, using utf-8 (detected in locale settings)
File critical.tar.gz.gpg is larger than 4GiB-1.
-allow-limited-size was not specified. There is no way do represent this file size. Aborting.
:-( write failed: Input/output error
#remember to us........
On a test machine Iwas never able to access to a newly created 4th partiton. As we can see there are dev devices for everything but the 4th partition.
The normal "partprobe" or "kpartx" or kernel being told to rescan the block device didn't help (only a reboot did).
fdisk -l /dev/sda
Disk /dev/sda: 750.2 GB, 750156374016 bytes
255 heads, 63 sectors/track, 91201 cylinders
Units........
Do you hate it when your ISPhas old cached records because of a high TTLon the DNS record of the relevant domain? In plain English this means you often can't connect to a site or service because your ISP's DNS servers haven't gotten word of the new IP address (probably because they haven't checked). There are also some that are notorious for ignoring TTL and not updating records for days!
But if you are lucky and smart enough to have your own Linux based DNS se........
The reason for not being able to read one of these dreaded/ fillable "XFA" forms is because no Linux PDF reader that I'm aware of supports them. Part of this reasoning is for security. It is really silly, they should ban these XFA forms or at least replace the Please Wait with the non-fillable version.
Download Adobe Reader 9.5 for Linux from here:
This is the solution but only so much, at least for me I was able to view th........
First you need the "iptables-persistent" package. This gives you an init script that loads your settings from /etc/iptables/rules.v4 and rules.v6
When you install it, it wll save your default setings in /etc/iptables.
sudo apt-get install iptables-persistent
Remember that the rules are stored here:
For IPV4: /etc/iptables/rules.v4
For IPV6: /etc/iptables/r........
Cisco's CUCM (Cisco Unified Communication Manager) is a system that combines voice, video, data and mobile products into a single unified management suite. At its core, the CUCMis like a "Super PBX" that controls the flow of all communications through an organization even single or multiple site deployments.
Cisco's CUCMmakes communication more effective and simple through centralized management and unification of communications resources.........
A quick check in /dev/pts shows a lot of entries but what are they for?:
ls /dev/pts
0 10 12 14 16 18 2 21 23 25 27 29 30 32 4 6 8 ptmx
1 11 13 15 17 19 20 22 24 26 28 3 31 33 5 7 9
Basically they are pseudo-termi........
umask are the default permissions that are applied when a file or directory are created. To see this in action simply just "touch filename" or "mkdir somedir" and you'll see what default permissions are applied.
The first thing Ialways tell people you should know is to NEVER change the defaults unless you are making them more restrictive. But they work well and if you change the defaults you could end up creating a file without permission to read........
Ihave a directory structure which the primary user needs full access on but wanted a user to access only a specific directory within the main directory (so they could write in there only and nowhere else).
Here's what Idid:
[root@compevo8001 dllnow]# ls -alh
drwxrwxr-x 2 someuser software 4.0K Oct 19 2017 ExpireYMD-2017-11-20
drwxrwxr-x 2 someuser software 4.0K Nov 19 2017 ExpireYMD-20........
You can do other things but this particular script is just to set all AMD cards to 80% fan speed (remember this script needs to applied everytime you reboot). You could set it is a cron or just throw it into /etc/rc.local
basepath=/sys/class/drm
for hwmon in `ls -1 /sys/class/drm|grep card[0-99]$`; do
echo card=$hwmon;
hwmonname=`ls $basepath/$hwmon/device/hwmon|grep hwmon[0-99]`
hwmonpath=$basepath/$hwmon/device/hwmon/$hwmonname
echo "ec........
You'll have to violate the iso9660 standards but it is necessary if you want to preserve your filesystem and filenames and shouldn't be an issue as long as you are using a modern OS like Linux.
genisoimage -o Backup-Myfiles.iso -r -J -joliet-long /some/path/
You will get errors like below (even enabling joliet-long didn't help)
genisoimage: Error: /some/filename.pdf have the same Joliet name
Joliet tree sort failed. The -joliet-lo........
4.374647] usb_common: exports duplicate symbol usb_get_dr_mode (owned by kernel)
[ 4.403334] usbcore: exports duplicate symbol __usb_get_extra_descriptor (owned by kernel)
[ 4.427736] xhci_hcd 0000:00:15.0: xHCI Host Controller
[ 4.427844] xhci_hcd 0000:00:15.0: new USB bus registered, assigned bus number 1
[ 4.429040] xhci_hcd 0000:00:15.0: hcc params 0x200077c1 hci version 0x100 quirks 0x01109810
[ 4.429141] xhci_hcd 0000:00:15.0: cache line size of 64 is not sup........
#Linux Mint 18.2 how to install gajim .16.9 so you can use OMEMO encryption:
sudo apt-get install python-axolotl python-nbxmpp
wget https://gajim.org/downloads/0.16/gajim-0.16.9.tar.gz
tar -zxvf gajim-0.16.9.tar.gz
cd gajim-0.16.9
./autogen.sh ;make;sudo make install
#if you get this error you need to get a newer python-nbxmpp from here:
gajim
Gajim needs python-nbxmpp >= 0.6.1 to run. Quiting...........
wget https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe
--2018-08-16 05:11:16-- https://downloads.linux.hpe.com/repo/spp/rhel/6/x86_64/current/CP017004.scexe
Resolving downloads.linux.hpe.com (downloads.linux.hpe.com)... 15.249.152.85
Connecting to downloads.linux.hpe.com (downloads.linux.hpe.com)|15.249.152.85|:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: 1525561 (1.5........
sudo apt-get install hwloc-nox
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following NEW packages will be installed:
hwloc-nox
0 upgraded, 1 newly installed, 0 to remove and 530 not upgraded.
Need to get 151 kB of archives.
After this operation, 453 kB of additional disk space will be used.
Get:1 http://archive.ubuntu.com/ubunt........
Usually this is because when you created your user you added a user but didn't create their home directory and/or for some reason your .bashrc and .bash_profile in ~ (home) is broken/missing.
In your home just create the following files with the following content to solve it:
.bashrc and .bash_profile.
To apply it just relogin/start a new bash session
# .bash_profile
# Get the aliases and funct........
zenity is a nice utility as part of the gnome window manager that allows you to script from bash and retrieve the input from the user. It could also be helpful in just notifying a user when they login with a popup window.
I'll give an overview of what's available with zenity:
Application Options:
--calendar Display calendar dialog
--entry Display tex........
You can find many ways to specify the VLANin your network configuration but Ifind this is the simplest and quickest.
In this case we are talking about a bridged adapter "vmbr0" but it works even if you just had a normal non-bridged interface.
The key here is that in vmbr0 you'll notice there is no IP address. We just specify "manual".
Below it is a similar stanza for "vmbr0.58" in this case 58 represents the VLAN (change........
./tronwatch: error while loading shared libraries: libasound.so.2: cannot open shared object file: No such file or directory
[root@testing linux-unpacked-1.0.7]#
Solution:
yum -y install alsa-lib-devel........
sudo apt-get install libcurl4-openssl-dev git build-essential autotools-dev autoconf libcurl3
sudo apt-get install libcurl4-gnutls-dev
git clone https://github.com/wolf9466/cpuminer-multi
sudo apt-get install cmake libpthread-* libmicrohttpd-dev libssl-dev libhwloc-dev
git clone https://github.com/fireice-uk/xmr-stak-cpu.git
make install
cd bin
chmod +x xmr-stak-cpu
./xmr-stak -O xmr........
To remove all spaces from all files in the current directory
linux rename remove spaces
rename "s/ //g" *
how to replace part of the text with another (it is almost like using sed):
rename s/"Screenshot at 2019-04-22 "/"AC97-Windows-InstallSolution"/g *
The first part "Screenshot at 2019-04-22" is what we're looking for
The........
https://yarnpkg.com/lang/en/docs/install/#centos-stable
curl --silent --location https://dl.yarnpkg.com/rpm/yarn.repo | tee /etc/yum.repos.d/yarn.repo
If you need node.js:
curl --silent --location https://rpm.nodesource.com/setup_6.x | bash - yum install nodejs yarn........
dvd+rw-mediainfo /dev/sr0
INQUIRY: [ASUS ][BW-16D1HT ][3.00]
GET [CURRENT] CONFIGURATION:
Mounted Media: 11h, DVD-R Sequential
Media ID: RITEKF1&n........
Ialready have the caja-image-converter option installed but it shows nothing.
Weirdly enough if you install nemo and nautilus converter it does show and work inside caja:
The solution is to install *-image-converter
sudo apt-get install *-image-converter
Reading package lists... Done
Building dependency tree
Reading state information... Done
Note, selecting 'n........
We all know Linux is known for good memory management but is it really? It seems all on its own with hardly anything running that you can come back in days or weeks and find that almost all of your RAMis used!
And many will say "no don't worry it's buffers for optimization" but it doesn't seem to help because what is in buffers is not available to use for new programs running or ones that allocate more RAM as far as Ican tell.
The reason Iknow........
Many people are aware of the "eject command" which works as you would expect.
To eject the disc:
sudo eject /dev/sr0
To insert the disc again you still use the same command but with the "-t" close try toggle:
sudo eject -t /dev/sr0
........
You can search for this bug and it seems like it may be related to ecryptfs and is many years old.
The symptoms are that you return to the computer and the screensaver was active or the screen was asleep/black and it doesn't seem to come back. But you check by SSH the computer is running fine and are frustrated you'll lose your running programs and have to reboot.
There is a simple solution:
Ctrl + Alt + F1
Ctrl +Alt + F8
Ba........
I've read a few guides about this but they didn't work for me.
sudo apt-get install bridge-utils
#don't think the above is enough it won't work still even though you have by default an /etc/qemu-ifup that handles it if you have the right tools and setup
sudo qemu-system-x86_64 -net tap -net nic -enable-kvm -cpu host,vmx=on ~/VirtualBox VMs/vsphere-vcenter/vsphere-vcenter.vdi
W: /etc/qemu-ifup: no bridge for guest interface foun........
sudo apt-get install nfs-kernel-server #oops there are no exports so it won't startsudo /etc/init.d/nfs-kernel-server start* Not starting NFS kernel daemon: no exports.
#we will use the /tmp/nfstestshare directory for our NFS share
mkdir /tmp/nfstestshare
#add it to /etc/exports (basically what NFS checks to determine what to make an NFS share)
/tmp/nfstestshare 192.168.1.5(rw,sync,........
#mount the VCSA DVD
mount /dev/sr0 /mnt/cd
#alternatively you could mount the iso directly
mount -o loop vcsa.iso /your/mount/path
#for this purpose we are using the CLI installer on Linux
cd /mnt/cd/vcsa-cli-installer/lin64
#no it's not going to be that easy you can't just run vcsa-deploy like that you need to use a template or configured .json file
./vcsa-deploy
Usage: vcsa-deploy [-h] [--version] [--supported-deploymen........
This is most likely to happen on a normal GUI system like Ubuntu or Linux Mint. If you or the user is meant to have sudo / root privileges it is as simple as editing the following files:
Now assume your username is "iamtheuser"
vi /etc/group
adm:x:4:syslog,iamtheuser
sudo:x:27:anotheruser,iamtheuser
Find the above lines and add a comma and "ia........
A simple way that may work for a lot of people who just need basic output for their scripts or daemons to announce an action is this:
echo "body or message" | mail -s "realtechtalk.com" user@domain.com
If you want to send a text file as the body just do this instead:
mail -s "realtechtalk.com" user@domain.com < /tmp/sometxtfile.txt
These are some ve........
This is not the normal "black screen"issue and I was shocked to eventually find out why. The normal advice of reconfiguring Xorg didn't work. Even booting into "Recovery Mode" did not help.
Here is the short end of the stick that fixed it:
sudo apt-get install mdm mate-desktop-environment
Yes you got it right, mdm and the mate-desktop-environment / gnome were somehow uninstalled. This must be whe........
It looks like this has something to do with APIC but I am not sure. I have similar CPUs with a different MB and BIOS that work fine on the same type of kernel. A lot of time the issue is because of the C-step setting in the BIOS.
The same thing happened on the 2.6 kernel with Centos 6 but this is a homebrew 4.4 kernel soI am not sure why it is happening when even Centos 7 (3.2) kernel works OK.
Solution - It comes down to the BIOS set........
In xplayer Iget the following error "Could not initialize supporting library.". It actually looks more like a gstreamer issue.
For those wondering what the default video player is called it is "xvid" and not "totem" anymore like previous versions.
Basically it looks like some codecs are missing when I uninstalled another program it uninstalled other programs and codecs that it shouldn't have.
I've tried installing all the gstre........
In your browser go to "about:config"
Right click and choose "New" ->"String"
The name should be:
general.useragent.override
String Value:
Mozilla/5.0 (Linux; U; Android 2.2.1; en-ca; LG-P505R Build/FRG83) AppleWebKit/533.1 (KHTML, like Gecko) Version/4.0 Mobile Safari/533.1
You don't even have to restart to make this work.........
This works for almost all ISO's Ifind (at least Linux based):
sudo dd if=CentOS-6.9-x86_64-minimal.iso of=/dev/sdg bs=20M
20+1 records in
20+1 records out
427819008 bytes (428 MB) copied, 118.233 s, 3.6 MB/s
Of course change the .iso filename above and the /dev/sdg to your desired USB drive!........
It is well known hackers, the NSA, CIA and other groups have created malware to secretly turn on your webcam and microphone on your phone, tv etc.. But fortunately on our computers and laptops we have some options.
Most webcams use the "uvcvideo" kernel module / driver. You can disable this in two ways on boot. I recommend both just as a failsafe.
Disable it on rc.local once your system boots automatically
Add the followi........
sudo chmod 000 /etc/cron.daily/apt-compat
This is the easiest way to disable the cron without anything more invasive like deleting the file.
After that you won't have anymore apt-get's starting.
This can be critical for systems without much extra RAMthat is not in use. I've seen systems that have swapped and crashed over apt-get.........
You can download the latest Sea Monkey releases here and 64-bit issues are a thing of the past now:
It's a little tricky if you are running a 64-bit OS which most people will be.
The weird thing is that the Seamonkey website for Linux seems to only provide a 32-bit download.
seamonkey-2.49.2.tar.bz2
Seamonkey is still provided as a tar.bz2 which you need to extract and run manually.
First........
So I have a domain "testdomain.com".
Inside test domain.com's root is the following .htaccess:
Options +FollowSymLinks -Indexes
ErrorDocument 403 /launch/index.html
Order Deny,Allow
Deny From All
Allow From 192.168.1.2
When you visit anything other than root things work fine. Eg. if you visit http://testdomain.com/somedirfile.html
It will show the right error in /launch/........
Just type the command:
localboot
By default it will boot the first local drive "0". Ibelieve you can specify a different number to boot a different device.
eg.
localboot 3
(will boot the 4th BIOS device)'........
It has been a big pain for a long-time to install Windows from a Linux environment. I used to run a windows install server and it never worked right for some reason (the install would fail on most servers).
Before getting start be sure to setup your samba share so once you boot into WinPE you can mount the install for whatever Windows you want
/etc/samba/smb.conf
[smbwinstall]
path = /tftpboot/images/winstall
guest ok = yes........
I've never seen this before in all of my years. Ihave some very old CDs and DVDs 12-15 years old that seem not to work in this BD-R/DVD-R/CD-R Asus drive.
The discs are fine actually and ironically they even work fine on a normal LG USB based BD-R drive!
Here are the errors in Linux:
[2914936.884924] attempt to access beyond end of device
[2914936.884927] loop1: rw=0, want=730424, limit=688384
[2914954.556873] attempt to........
The easiest way is to use SSHand DD or a combination of netcat. SSHwill be a little slower due to encryption but is the most secure way (on two older systems the average clone speed is about 40-50MB/s). This is also OS independent as it doesn't matter what the source OS is because you are literallly cloning the drive so you retain the partition table and settings.
Clone HDD using SSH and DD........
I don't recall having this issue in the distant past but nowadays at least Debian seems to be very picky about this.
I used dd to copy one hard drive to another and tried booting it. Everything seemed fine with grub working but each time it would drop to the busybox shell. There is no particular error so this is misleading.
Normally the first things you would check are to make sure your fstab is correct (that the UUID is correct)and that you've updated grub.&........
ssh rtt@192.168.1.199
Unable to negotiate with 192.168.1.99 port 22: no matching host key type found. Their offer: ssh-dss
It looks like the DSS option is not considered secure so when connecting from newer Linux systems to an older one you will get the above error.
It can be fixed (but you should consider upgrading your SSH daemon):
ssh -oHostKeyAlgorithms=+ssh-dss rtt@192.168.1.199........
This guide will work for most modern Linux versions like Centos RHEL 7, Debian, Mint, Ubuntu etc...
In Centos 7 the days of editing the "kernel"line and adding "single"are gone. On top of that sometimes after a new install passwords do not work, maybe you forgot your password or for some other reason you need to break in or fix your system? It could also be because you can't mount your root / or some other /etc/fstab error and many other err........
PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/geoip.so' - /usr/lib64/php/modules/geoip.so: undefined symbol: GeoIP_country_code_by_name_v6 in Unknown on line 0
Remove the GEOIP from PHP:
php71w-pecl-geoip-1.1.1-1.w6.x86_64
PHP Fatal error: PHP Startup: apc_shm_create: shmget(0, 67108864, 914) failed: Invalid argument. It is possible that the........
Install requirements:
yum -y install gmp-devel mpfr-devel libmpc-devel glibc-devel glibc-devel.i686 zip unzip jar
Download, untar, configure, compile and install GCC
http://mirrors.kernel.org/gnu/gcc/gcc-5.5.0/gcc-5.5.0.tar.gz
tar -zxvf gcc-5.5.0.tar.gz
cd gcc-5.5.0
./configure
make
make install
Now you need to cleanup th........
The Linux Kernel interpretated a very high volume of real traffic as a DDOS attack so it basically ends up blocking your web server.
possible SYN flooding on ctid 42131, port 80. Sending cookies.
Simple fix edit sysctl values for max_syn_backlog
sysctl -w net.ipv4.tcp_max_syn_backlog=5000
To make them permanent edit /etc/sysctl.conf
echo "net.ipv4.tcp_........
In the "last" command in Linux by default it will show the information with the hostname (not very useful at all especially since it normally truncates long hostnames).
To get last to show the IP address use this:
last -i
The -i makes it show the numeric IP instead of hostname.........
yum -y install samba
vi /etc/samba/smb.conf
https://www.kernel.org/pub/linux/utils/boot/syslinux/syslinux-6.03.zip
mkdir syslinux;cd syslinux;unzip syslinux-6.03.zip
mkdir -p /tftpboot/libs/
cp bios/com32/modules/linux.c32 /tftpboot/libs/
cp bios/com32/libutil/libutil.c32 /tftpboot/libs/
cp bios/com32/lib/libcom32.c32 /tftpboot/libs/
#add lib path
echo "PATH libs" >> /tftpboot/pxeli........
Normally lspci will show you just like this and would suggest they are exactly the same card:
1a:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Ellesmere [Radeon RX 470/480/570/580] (rev e7)
1c:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Ellesmere [Radeon RX 470/480/570/580] (rev e7)
lspci -vnn is the answer
As we can see one is a Gigabyte and the other is an MSI card. Wha........
This works with lspci and if it's outdated may not give you the exact manufacturer and device model.
For example take these 3 different RX 580's:
1a:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Device 67df (rev e7)
1b:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Device 67df (rev e7)
1d:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Device 67df (rev e7)
You ca........
Check for crap in /var/lib/mysql like this
ls -al /var/lib/mysql/
total 20888
drwxr-xr-x 24 mysql mysql 4096 Oct 3 18:30 .
drwxr-xr-x 20 root root 4096 Oct 3 04:23 ..
-rw-rw-rw- 1 mysql mysql 11776 Oct 3 17:10 c:exp.exe
-rw-rw-rw- 1 mysql mysql 48128 Oct 3 17:10 c:exp1.exe........
This is not just a Linux issue but a general issue most software or hardware players cannot play the resulting exported/backed up format of .h264 from DVR security camera footage for some silly reason.
There is a simple solution in Linux using ffmpeg fortunately.
Convert the .h264 file into mp4
ffmpeg -i yourfile.h264 -codec copy video.mp4
play dvr .h264 file........
Have you have a command ask a question such as cp or move?
You can do this:
echo y|cp * /tmp/othercopy
However it may still fail if your bashrc aliases have the "-i" flag see this post here.........
This through me for a loop when I would do a cp -rf or mv -f nothing would get overwritten even if piping y or yes to the command.
Type alias and you'll see why:
alias cp='cp -i'
alias l.='ls -d .* --color=auto'
alias ll='ls -l --color=auto'
alias ls='ls --color=auto'
alias mv='mv -i'
alias rm='rm -i'
The -i is a safeguard against messing things up but however does mess things up worse when you know what........
Linux Set Date
date -s "YYYY-MM-DD HH:MM:SS"
date -s '2014-12-25 12:34:56'
BSD Unix Set Date
date yymmddhhmmss
date 170809121156........
I have never had this error on Linux and this is running FreeBSD as root:
Wed Aug 9 04:29:34 2017 us=329050 Cannot allocate TUN/TAP dev dynamically
Wed Aug 9 04:29:34 2017 us=329832 Exiting due to fatal error
The Solution you need a kernel module that is for some reason not automatically loaded like Linux:
kldload if_tap........
sudo mount -a
Unable to find suitable address.
[35758.706993] CIFS VFS: Error connecting to socket. Aborting operation.
[35758.707247] CIFS VFS: cifs_mount failed w/return code = -111
[35795.476160] CIFS VFS: Error connecting to socket. Aborting operation.
[35795.476346] CIFS VFS: cifs_mount failed w/return code = -111
When the above happens "Unable eto find suitable address" it usually means the smb nam........
To get the first X letters of a word:
It's very simple you can just pipe it to head with
-c 1 (gives the first letter and so on)
-c2 (2 gives the first 2 letters).
echo "dsjfsdlksjdklf;jlsd;kflasdj;kl"|head -c 2
Returns ds
To get the last X letters of a word:
Now we use tail with -c but it works differently. ........
Just a note before you do this you should have a sure, guaranteed way into the system such as local, KVMor preferably publickey making bruteforce SSH absolutely impossible since there is no password to bruteforce and even if someone knew the password they wouldn't be able to login except from the local console (presumably you should make sure no one unauthorized has physical access).
1. Edit /etc/ssh/sshd_config
Find the section like this:........
A great way when moving your equipment to a new location, new router/switch etc to help confirm what MAC has what IP:
for ip in `arp -na|awk '{print $2}'|sed s/(//g|sed s/)//g`; do
echo ping $ip
ping -c 1 -w 1 $ip > /dev/null
if [ "$?" == 0 ]; then
echo "$ip UP"
fi
done........
I have never had this error on Linux and this is running FreeBSD as root:
Wed Aug 9 04:29:34 2017 us=329050 Cannot allocate TUN/TAP dev dynamically
Wed Aug 9 04:29:34 2017 us=329832 Exiting due to fatal error
The Solution
You need a kernel module that is for some reason not automatically loaded like Linux:
kldload if_tap........
First of all check to see which version if any you have available for a downgrade:
apt-cache showpkg packagename
Downgrade/Install old package:
apt-get install package=version
Example
apt-cache showpkg caja
Package: caja
Versions:
1.10.3-1+rafaela (/var/lib/apt/lists/packages.linuxmint.com_dists_rafaela_import_binary-amd64_Packages) (/var/........
In Debian/Ubuntu this is called "holding".
To hold/exclude a package from being installed or upgraded:
sudo apt-mark hold packagename
To allow the upgrade/installation unhold:
sudo apt-mark unhold packagename........
sudo tar --ignore-failed-read -czvf mycomputer-backup.tar.gz --exclude=/home/otheruser/* --exclude=/proc/* --exclude=/sys/* /
Note the --exclude clauses and modify/add according to your needs........
When using the .sh script the rendering doesn't work after an upgrade of related packages to kdenlive.
kdenlive (kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1)) with affine or composite transitions was fine but is now broken during the time of transition it is just a white screen.
The previous version was fine:
kdenlive:amd64 (4:17.04.1+git201705191233~ubuntu16.04.1
But now I can't find it or install it:........
[1035724.274610] [drm:intel_pipe_update_end [i915_bpo]] *ERROR* Atomic update failure on pipe A (start=62076478 end=62076479) time 102 us, min 894, max 899, scanline start 893, end 900
W: Possible missing firmware /lib/firmware/i915/kbl_dmc_ver1.bin for module i915_bpo
I've been getting those errors on a J3455 NUC box with the latest kernel on Linux Mint 18.2. When updating the initramfs I also got the error about the firmware........
cagecoin linux compile:
sudo apt-get install qt4-qmake libqt4-dev build-essential libboost-dev libboost-system-dev
libboost-filesystem-dev libboost-program-options-dev libboost-thread-dev
libssl-dev libdb++-dev libminiupnpc-dev
Solution:
sed -i s/"BOOST_LIB_SUFFIX=-mt-s"/"#BOOST_LIB_SU........
Solution:
Aptitude is very smart and fixed the issues it was because of nvidia cuda and opencl and nothing else suggested or hinted this using apt
sudo aptitude install wine
The following NEW packages will be installed:
ocl-icd-libopencl1{ab} ocl-icd-libopencl1:i386{ab} wine wine1.6
wine1.6-amd64{a} wine1.6-i386:i386{a}
The following packages will be REMOVED:........
Essentially a program I was running for mining did not terminate properly with Ctrl+C it is listed as defunct and cannot be killed, kernel is tainted and normal tricks to disable the port are impossible the dev and sys entries for the device cannot be browsed or interacted with in any form without a lockup of the request. The only solution is to reboot due to the kernel taint as far as I can find so far.
[1130246.811056] INFO: task minerd:21861 blocked for more th........
#if you have nvidia make sure you install the nvidia-cuda-toolkit so hardware acceleration can be used
wget http://ffmpeg.org/releases/ffmpeg-3.3.2.tar.bz2
tar -jxvf ffmpeg-3.3.2.tar.bz2
cd ffmpeg-3.3.2/
./configure --disable-yasm
install prefix /usr/local
source path ........
The old MBR 512 bytes partition table is no longer valid if you are using GPT.
To copy a GPT table with dd to another disk do it like so:
Below sda is the source disk and destination disk is sdb (change to meet your needs).
Depending on how you use this, you have to be careful. The assumption is that you should only dump the partition table back to a disk you will newly format. If not you'll need to ch........
user@box:~$ sudo tune2fs -l /dev/md99
[sudo] password for user:
tune2fs 1.42.9 (4-Feb-2014)
Filesystem volume name:
Last mounted on: /mnt/md50
Filesystem UUID: 976a8655-2619-4587-878c-dab07f7b7652
Filesystem magic number: 0xEF53
Filesystem revision #: 1 (dynamic)
Fi........
I am using a GTX 1060 but replace the download for the driver with the correct/current version for your particular card by visiting: http://www.nvidia.com/Download/index.aspx?lang=en-us
yum install automake curl openssl-devel libcurl-devel gcc gcc-c++
yum -y install kernel-devel-`uname -r`
yum -y install unzip
#the........
This is a VIA made VL805 USB 3.0 Chipset with 4-ports and MOLEX powered. First of all this unit was cheap at about only 9 USD with fast shipping. My biggest concern was if this was a quality unit and would it really give you full USB 3.0 speeds (some people reported with similar cards that for some weird r........
Why won't my Linux Mint boot after I manually installed a new kernel?
eg.
apt-get install linux-image-newerone
Do this
dpkg -l|grep linux-image|grep extra
ii linux-image-extra-3.16.0-38-generic 3.16.0-38.52~14.04.1&nb........
When running cudaminer once it tries to initialize the card the entire screen freezes. The computer itself is still running but the Xorg is done for, you cannot even switch to another console window and must reboot (even an mdm or Xorg restart does not help).
At first cudaminer will give you these errors:
stratrum_recv_line failed
...retry after 15 seconds
GPU #0: Geforce 210 with compute ca........
sudo mkdir -p /etc/X11/xorg.conf.d/
sudo vi /etc/X11/xorg.conf.d/20-intel.conf
On newer Ubuntu / Mint / Debian systems the file would go in: /usr/share/X11/xorg.conf.d/20-intel.conf
Type "i" and enter the following:
Section "Device"
Identifier "Intel Graphics"
Driver&n........
Here is a simple MP3 player and now there's a reason to understand why the supplied cable has some kind of capacitor and is very short. These devices can be VERY finicky and any voltage fluctuation or difference is enough to cause issues.
Take for example the error messages from Linux Mint:
[804829.895414] usb 1-1: USB disconnect, device number 11
[806961.109030] usb 1-1: new high-speed USB device number 12 using xhci_hcd........
This is mainly the case on Centos but applies to other distros and situations. If you are running programs in the background with the &, at least in Centos it is usually not honored and if you quit or are disconnected the backgrounded programs will be sent sighup and be shut down.
The simplest way around this instead of using & is to start any programs or commands with "nohup"
Eg.
nohup yourscript.sh........
Finally after ages I found the solution which is on many pages on the net but not obvious and should have been standard or more common info!
Instant Solution:
Type this into the terminal (unfortunately the driver config menu doesn't have the option as itis hidden):
nvidia-settings --assign CurrentMetaMode="nvidia-auto-select +0+0 { ForceCompositionPipeline = On }"
Make permanent
Cli........
Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Missing folder chosen by user:
Jun 1 15:45:42 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: project_data:INFO Removed missing file: MAH02949.MP4
Jun 1 15:45:57 videoeditor-desktop org.mate.panel.applet.MintMenuAppletFactory[1882]: ui_util:WARNING Icon theme media-playback-start not found. Will use backup........
These errors believe it or not are simply because of not being the root user or running with sudo! However if you didn't know to try as root you'd think there was a problem with your burner or disc Essentially it looks like without root you cannot send the required scsi commands to continue writing. Ithink cdrecord should have built-in tests or safeguards to see if it has the permissions to run the required commands.
I guess for more advanced users the idea is simila........
I get the following error "Installer Crashed" on 18.1 MATE 64-bit when installing by NFS/PXE. Yet it was able to at least detect and use my NIC (perhaps the driver was only activated because of PXE/NFS being used)?
When using 18.1 Cinnamon on CD the NIC does not work but the installer did succeed. However it doesn't work right, I can't login graphically and get some Cinnamon OOMerror but how can this be with 8GB of RAM straight from login?........
*Update so this doesn't work it must be something to do with the path of nfs or something else but the installer fails with "Installer crashed" at the end whereas with the CD/USB it works.
This assumes you've already installed and configured a separate PXE/DHCP server somewhere else and your /tftpboot directory is setup.
This is for Linux Mint 18.1 but generally applies to most versions although you may have tro change things like "casper"........
Just type the following in the bash/terminal shell to enable the blue LED light on the Coolermaster CM Storm keyboard:
xset led 3
To make it automatic and permanent execute the following as root:
echo "xset led 3" >> /etc/rc.local
This is a fairly nice gaming keyboard whichI bought because I type very quickly and the cheap standard keyboards simply can't keep up!........
This happens on any file an even just typing "vi"whereas it never happened before. I suspect an update or environment variable is causing this issue
When entering vi I get this weird stuff
line 58:
E488: Trailing characters: t_Sbet
line 63:
E171: Missing :endif
When exiting vi I get this weird stuff
t_Sb=^[[4%?%p1%{1}%=%t........
1.) gedit/pluma
both very good the only thing I wish is that there was an autosave for unsaved documents! The only other competitor which is similar but I prefer less is kwrite (although I think kwrite may have proper autosave)
pluma seems to be a renamed gedit yet gedit is still installable on Linux Mint)
........
Normally the below would indicate a failing or failed drive. In this case the SATA port was unplugged and sometimes the Linux kernel/motherboard even with AHCIjust don't play nice and can't handle it.
What happened is Iplugged in a new drive after removing another one. However the log shows that after the old drive was plugged in the Linux kernel kept complaining thinking the drive was there but not responding properly. This continued even with reseating........
If you have this problem: http://realtechtalk.com/mencoder_bmovl_error_vf_bmovl_Unknown_command_Ignoring_-1860-articles
Then ffmpeg is for you. Go here if you are using Linux Mint and cannot find or install it to use an external PPA........
Based on this tutorial: http://www.linuxjournal.com/content/overlay-images-video-using-mplayer-and-mencoder
mencoder -oac pcm -ovc raw -vf bmovl=0:0:tfifo -o $output $file
vf_bmovl: Unknown command: ''. Ignoring. ........
I've had this issue since Ubuntu 9 and now even on Linux Mint 17 no matter what latest version of the Nvidia proprietary driver that I use. It just becomes slower and slower and only gets better after rebooting or restarting Xorg.
Someone here has it as well
https://askubuntu.com/questions/822449/graphics-becomes-slow-after-a-while/917886
It's very fru........
This is very annoying that ffmpeg is missing from Linux Mint! They have ffmpeg2theora which is a totally different codec and does not work as ffmpeg does at all (it is basically totally different).
However on Linux Mint 17 I was able to use a Ubuntu PPA and sucessfully install ffmpeg!
https://launchpad.net/~mc3man/+archive/ubuntu/trusty-media
Adding this PPA to your system........
Using Apache 2.2 and PHP5.6 PHPBB3 is very slow to respond. Actually for some reason it takes so long to even register a log entry in access_log as in several seconds or a few minutes later it shows up in Apache. All other vhosts and Apache access stops working and freezes until the request to access PHPBB3 slowly completes.
It seems to randomly be slow if you stop using it whether for posting or reading the forums. I've migrated to different machines including........
espeak - is horrible and sounds very old and robotic
echo "hello there"|espeak
#don't know how to use
mbrola and plugins
cicero
jovie just seems to be a graphical interface to espeak
There is also sbreader/sapi
Google's Text To Speech Works Quite Well
#!/bin/bash
say() { local IFS=+;/usr/bin/mplayer -ao alsa -really-quiet -noconsolec........
This command will generate a random password using all letters and numbers that is 20 characters wrong based on /dev/urandom (for the most truly random output).
echo `< /dev/urandom tr -dc _A-Z-a-z-0-9 | head -c${1:-20};echo;`........
This error is commonly due to Java security or TLS settings but there is a second issue with forwarded ports that also causes it.
1. Java Security/TLS Settings issue:
This article has the solution to change them all in Linux automatically
2. Port Forwarding Issue if your Avocent DSR is behind NAT/private IP........
gpick is a great and simple tool now that I now how to use it
sudo apt-get install gpick
The trick is to find "the swatch"
I was in a rush and was frustrated that it wouldn't work how Iexpected and I had to memorize the hex code of the color my mouse was over.
There is something it tells you to do which is "Click on the swatch area" (click onthe honeycomb graphic area that is the s........
There are usually two reasons for this.
#1 The most common is that you need to enable the -r (recursive) flag with zip to make it recurse into directories.
So the solution is to use -r
zip -r somefile.zip yourfiles
#2 If you are using bash scripting based on ls without the full path or for some other reason the full path is missing, zip looks for the files in the current directory so this will always fail.........
Normally an ls will just produce the actual contents of the current or target directory eg.
ls mydir
myfile1
myfile2
myfile3
But what if you need to find the full or relative path to another program that cares whether that be zip or etc.?
You need the "-d" switch and the asterisk inside the actual directory.
ls -d mydir/*
mydir/myfil........
tar -xvJf somefile.tar.xz
It is very annoying that so many are now using the .xz archive format as standard instead of .tar.gz but nevertheless above is how you would extract it with the "J" flag (not lower case j as that is for bz).........
whois in Linux is incredibly out of date and does not seem to recognize most new TLDs domains, but there is a quick and easy tip/hack/tweak for this.
An example of new TLD's site as .review .site .club
whois somesite.club
No whois server is known for this kind of object.
bash to the rescue
Now I did try to apply this in .bashrc but DONOT! Ithink the * wil........
Ijust use "ufraw" and it does the trick perfectly. Now Iwish I could figure out how to batch convert them into .jpg with ImageMagick (it seems support for .raw is not guaranteed or it has to be compiled in).
apt-get install ufraw........
In short the two drives in the array were /dev/sdd and /dev/sde. The kernel sees they were unplugged and have gone down as you can see below.
mdadm caught the first one being unplugged /dev/sde and disabled the missing drive. However when the final drive that was part of the array is unplugged it didn't notice at all. Instead it complains about an IO error later for drives that the kernel knows do not exist anymore.
[45817.162728] ata4: exception........
1.) Replicate the number of partitions in your new drives.
gdisk /dev/sda
gdisk /dev/sdb
I created 3 partitions of the same same size.
partition #1: +1G (/boot)
partition #2: +60G (swap)
partition #3: rest of it (/)
#note if you are using GPT/gdisk you need to create separate a partition at least 1MB in size (in my case I would a 4th partition and mark it type ef02).........
The solution is simply "tidy"/Tidy-HTML. It will take your poorly formatted HTML code (and I mean files that span just a few lines that are unreadable) and fix it up.
Note the command below does everything in place. *Make sure you take a backup of all .html files*
It also seems to break html5 code/templates so beware.
tidy -im yourfile.html
An automated way in bash:........
What code is being returned or where is a URL/domain redirecting you to? Curl makes this easy and simple:
curl -Iyourdomain.com........
mdadm won't boot in Ubuntu/Mint/Debian anymore.
You just get the following in a loop:
mdadm: CREATE group disk not found
Incrementally started RAID arrays.
Incrementally starting RAID arrays...
mdadm: CREATE group disk not found
Incrementally started RAID arrays.
Incrementally starting RAID arrays...
mdadm: CREATE group disk not found
Incrementally started RAID arrays.
Incrementally starting RAID arrays...
mdadm: CREATE group dis........
At first I thought it's just not possible but there is actually an option that can be enabled to make symlinks work with Samba.
Then I put this under the [global] section
Note: It's "wide links" and not "wide symlinks" (some other sites have incorrect info which was a frustrating waste of time :))
Add this to your smb.conf
follow symlinks = yes
wide links = yes
unix ex........
Add this to the .htaccess file
#right/working:
AddType application/x-httpd-php .html .htm
#wrong (won't work in many cases):
AddHandler application/x-httpd-php5 .html .htm........
Get the python "warc extractor" from here. WARC just seems to be such an unnecessary and complicated format. Why not use tar, rar, zip etc...?
./warc-extractor.py -dump content !http:content-type:pdf yourfile.warc........
convert -trim yourimage.png
That's all there is to it, very simple, clean and quick!........
This happened while updating Linux Mint/Debian/Ubuntu on a remote SMB/Samba share.
Solution
After waiting for updates to complete things will work normally but it really is strange that the service actually stops working or is disabled for so long during the update. It is likely the update process stops the serivce and only restarts after the update is complete.........
PHP Fatal error: PHP Startup: apc_shm_create: shmget(0, 67108864, 914) failed: Invalid argument. It is possible that the chosen SHM segment size is higher than the operation system allows. Linux has usually a default limit of 32MB per segment. in Unknown on line 0
PHP Fatal error: PHP Startup: apc_shm_attach: shmat failed: in Unknown on line 0
This error is not at all fun because it actually prevents Apache/httpd from starting or working at all. It will........
sudo fdisk /dev/sdh
WARNING: GPT (GUID Partition Table) detected on '/dev/sdh'! The util fdisk doesn't support GPT. Use GNU Parted.
WARNING: The size of this disk is 8.0 TB (8001563221504 bytes).
DOS partition table format can not be used on drives for volumes
larger than (2199023255040 bytes) for 512-byte sectors. Use parted(1) and GUID
partition table format (GPT).
The device presents a l........
md127 issue, it should be /dev/md3 per mdadm.conf
Any time something is mounted as md127 it almost always means there is no entry for this mdadm array in the mdadm.conf in initramfs (which is separate from your actual /etc/mdadm.conf).
cat /etc/mdadm.conf
ARRAY /dev/md3 metadata=1.2 UUID=b6722845:381cc94e:7a2c5b5f:8e3b7c4f
The reason for this is something strange, most Linux OS's bizarrely always keep their own copy of /etc/mdadm.con........
Now many people report this card simply not working in various Linux distros and kernels. My issue is different, it always works at 100mbit (eg. plugged into a 100mbit switch) but no matter what 1000M/gigabit switch I would try, it would never work.
The link would be up (the lights were on) and the OS detected the link as being up as well but it wouldn't work at all and could not pass data in or out (not even a ack/ping).
There is one simple solution and command........
M4A is a weird format, so you have to be creative here is a quick copy of what I did.
Basically you need to convert to .wav to make use of them and thenI converted the resulting .wav into an mp3 (nice small file size and basically universally playable):
=======
sudo apt-get install mpg321 mp3gain faad normalize lame
faad "Voice 002 (copy).m4a"
faad "Voice 002 (copy).m4a"........
To disable NCQ in the Linux kernel (change sda to match your device).
echo 1 > /sys/block/sda/device/queue_depth
To enable NCQ (change sda to match your device).
echo 31 > /sys/block/sda/device/queue_depth........
We've all done this at some point, you work on the wrong shell window and this was my first time making this mistake but I deleted a partition table in fdisk, recreated it and saved it with "wq" and even ran partprobe! If you haven't rebooted yet then you can still recover your partition table, otherwise you're in big trouble.
Fortunately since it was a live system and in use the kernel still had to use the old table like below:........
I still cannot understand how this would not be enabled by default and I struggled to find the reason why with manually installing samba etc.. wondering why the option for sharing was not in the menu.
On Linux Mint "MATE" the package is called "caja-share" and on Cinnamon it is called "nemo-share" so edit the below command as necessary:
*Also note that the "samba" package is necessary as it is not inst........
This happened while an mdadm array was syncing, all access from writing a new blank file to opening a small .txt file was very slow:
[222117.312078] kjournald starting. Commit interval 5 seconds
[222117.685060] EXT3-fs (md0): using internal journal
[222117.685096] EXT3-fs (md0): mounted filesystem with ordered data mode
[222122.376847] kjournald starting. Commit interval 5 seconds
[222122.602825] EXT3-fs (md2): using internal jour........
You may get this after a long time of not rebooting but especially if you have rsync'd a / partition or deployed an image to another VPS or computer, you will often have this issue.
The good thing it usually just takes a reboot.
Here is more info from Centos........
Errors like this are shown on high usage servers and ports so it is common to see it on http and even imap ports:
possible SYN flooding on port 80. Sending cookies.
The Linux kernel will even detect flooding on OpenVZ containers:
possible SYN flooding on ctid 6000, port 993. Sending cookies.
In many cases this is not an issue and is more so simply a result of regular, but high usage traffic.........
In Firefox I cannot connect to any website, proxy is disabled and outside network access is confirmed, no system or manual proxy was set on this Linux Mint/Ubuntu system. Normally this can be caused by proxy or DNS problems and the weird thing is that traceroute and ping to other IPs worked fine but even connecting to sites by IP was not working.
The connection was reset
The connection to the server was reset while the page was loading.........
Usually the cause is inexplicable because some things just don't work correctly even when calling all commands by their full path.
Usually adding the following to your crontab file at the top will fix/solve the issue:
SHELL=/bin/sh
PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin
........
This is using find and -mtime in Centos Linux, it simply takes "n" (which is a day) as a number and you can specifiy a + or - to say older or less than a certain age.
# (show everything older than 1 day)
find . -mtime +1
........
For themes and custom CMS setups, the typical HTML theme is not ready to go at all but here are some common sed commands (search and replace that will get most of them working without breaking as you'd expect).
The problem is that often the theme directory will be separate from the content and this will break the relative paths that these themes use.
sed -i s/'href="'/'href="/themes/yourtheme/'/g index.html
sed -i s/'src="'/'src="/themes/y........
Stopping httpd: [FAILED]
Starting httpd: httpd: Syntax error on line 73 of /etc/httpd/conf/httpd.conf: Cannot load /etc/httpd/modules/mod_file_cache.so into server: /etc/httpd/modules/mod_file_cache.so: cannot open shared obje........
Auction 262382440107: Cannot connect to URL : SSL connect error: gnutls_handshake() failed: Illegal parameter
Retrying...
esniper encountered a bug. It looks like your esniper version is not
current. You have version 2.28.0, the newest version is 2.31.0.
Please go to http://esniper.sf.net/ and update your copy of esniper.........
At first my BIOS said the card may not work right because there is no more option ROM space.
I disabled the Option ROM for both LSI 1068 and 2008 chipsets, Network Boot ROM and most other PCI slots, Serial Port, etc... and the message went away but the card still does not work properly.
But it still cannot initialize the card properly(does not work):
[ 33.943272] NVRM: This PCI I/O region assigned to your NVIDIA device is invalid:........
Download from here http://www.avagotech.com/products/server-storage/host-bus-adapters/sas-9200-8e#downloads
sudo Installer_P20_for_Linux/sas2flash_linux_i686_x86-64_rel/sas2flash -listall
LSI Corporation SAS2 Flash Utility
Version 20.00.00.00 (2014.09.18)
Copyright (c) 2008-2014 LSI Corporation. All rights reserved
&nbs........
To check the version of Ubuntu just use the lsb_release command as shown below and you will be able to see the exact Ubuntu version you have installed.
lsb_release -a
No LSB modules are available.
Distributor ID: Ubuntu
Description: Ubuntu 14.04 LTS
Release: 14.04
Codename: trusty........
If Linux Mint 17 or other has no window buttons/controls you can do the following from terminal:
marco --replace&
Sometimes it can be fixed if you go to your themes/appearance and choose a new one but in the case like mine where Compiz is installed but not running/working then that fix will not work and will require the marco command above.
What if you can't type in a terminal Window?
If you close........
The Scenario
You have dual NICs and you disable NIC1 which uses 192.168.1.1 as its gateway. With NIC2 you enable it/connect it to another network which also has the gateway 192.168.1.1
Everything will work fine at this point.
When switching back to NIC1 even with NIC2 disabled and even unplugged, the OS basically can't pick up the new/updated ARP entry of the old device for 192.168.1.1 and perhaps thinks it is a security risk or spoof of some sorts and blocks i........
This is a real pain because I had to manually unplug ethernet cables for network testing or to use an alternate network or guarantee physical access to one network segment is cut off.
For some reason this happened after Ikilled dbus because it was confused and blocking packets thinking they were coming from the wrong interface since eth0 and eth1 both had the same subnet and gateway.
I eventually did a "service network-manager restart" but the option was........
Iwill start by saying I think I know what caused this boot-time error on Linux Mint but should also apply to Debian and Ubuntu.
I changed my BIOS time to several hours in the past to match the current time, but this caused Linux to think there were incorrect filesystem times.
The problem is that it seems when you hit this I am not sure what is happening, it doesn't seem to be doing fsck and hangs without prompting the user.
What I have found is that........
The below forces all request to your domain to go to the main non-www root domain.
Updated code:
RewriteCond %{HTTP_HOST} !=domain.com
RewriteRule ^(.*)$ https://newurl.com/subdir/$1 [R=301,L]
If you don't want it to go to a subdirectory:
RewriteCond %{HTTP_HOST} !=domain.com
RewriteRule ^(.*)$ https://newurl.com/$1 [R=301,L]
Bad code:
This code is bad beca........
apt-get install pptp-linux
echo "yourvpnusername * yourpasspass *" >> /etc/ppp/chap-secrets
vi /etc/ppp/peers/provpnaccounts.com
enter (ignore the lines):
============
pty "pptp server.provpnaccounts.com --nolaunchpppd"
name testuser
#remotename PPTP
require-mppe-128
file /etc/ppp/options.pptp
==========........
The following assumes the computer is local/physical to you and/or it always has a LANIP so it can be accessed on site without having a default gateway.
The key to this is not to set a default gateway for your computer or you can set a script on boot or other time to delete the gateway (where eth0 is the NIC you are using):
route del default eth0
50.80.20.2 is the VPN server you connect to
192.168.1.1 is your........
Debian/Ubuntu vi keyboard problem, up and down arrows do not work and instead make an A (Up), B (Down), C (Right) or D(Left).
The working solution
(you could also add the set nocompatible to /etc/vim/vimrc to make it system wide-will not be applied until reboot I believe):
echo "set nocompatible" > ~/.vimr........
Device Boot Start End Blocks Id System
/dev/sdc1 1 132 1060256+ fd Linux raid autodetect
Partition 1 does not end on cylinder boundary.
Partition 1 does not start........
Add the following to fstab where 192.168.1.125/Media is the samba share and where /home/homeuser/Downloads is where you want to mount.
Change user and pass to what is needed (if no pass is required it still works fine with the below).
//192.168.1.125/Media /home/homeuser/Downloads cifs user=guest,pass=bla 0 0
mount: wrong fs type, bad option, bad superblock on //192.168.1.125/Media,
&nbs........
This was a horrible shock after upgrading fromUbuntu 9 to Linux Mint 17 and I found that the last distro to support tsclient was Debian Squeeze.
For some reason it has disappeared for a long time and the new options such as rdesktop and gnome-rdp do not have any start menu entry and just aren't done as well as tsclient.
Fortunately there is a solution:
tsclient surprisingly can be downloaded as a direct .deb package and it fails with some variou........
grub> root (hd0,0)
root (hd0,0)
Filesystem type is ext2fs, partition type 0xfd
grub> setup (hd0)
setup (hd0)
But if you do:
root (hd1,0)
setup (hd1)
it does work, I think hd0/sda had a GPT partition that was not removed properly (what I did was just dd bs=512 count=1 the partition table from another drive since the partition table should be identical).
Checking if "/boot/grub/........
Say you have a bunch of files like this:
file-01.jpg
file-02.jpg
...............
What if you want to mass rename them?
the rename tool can work just like sed
For Debian based distros:
Note "file" is what we search for and "newname" is what we replace it with, so substitute according to your requirements.
rename s/file/newname/ name-file-*.jpg
For R........
mono/wine not working in Ubuntu/Linux Mint/Debian:
The assembly mscorlib.dll was not found or could not be loaded.
It should have been installed in the `/usr/lib/mono/2.0/mscorlib.dll' directory.
solution:
sudo apt-get install mono-complete
Problems:
mono does not work well for even simple things like a Winrar self extracting .exe fi........
Istanbul:
At least in Linux Mint the latest 17.2 version Istanbul freezes when "In process of saving to Disk" even with the workaround of not having Sound recording enabled. It looks like a great app but bugs like this seem to have plague it for over 8 years!
Kazam:
This little app works great, its only bug is that when you try to tell it to record a window or area it puts a gray cov........
It is just the readlink command with the -f switch and it will display the full path, very handy to save time when you want to copy and paste the location of a file or script etc..
readlink -f updatehtaccess.sh
/var/lib/updatehtaccess.sh
........
In this case we want to mount partition #2
fdisk -lu Centos-6.6-x86_64.img
You must set cylinders.
You can do this from the extra functions menu.
Disk Centos-6.6-x86_64.img: 0 MB, 0 bytes
255 heads, 63 sectors/track, 0 cylinders, total 0 sectors
Units = sectors of 1 * 512 = 512 bytes
Device Boot&nbs........
It sounds like this is corrected in later versions of the OpenVZ kernel but Iam not sure, it may also be that a much newer kernel is needed and Centos may not have a recent enough kernel.
*Debain 7.0 however does work fine as a temporary fix or work around.
Debian 8 OpenVZ no IP and networking not working:
lo Link encap:Local Loopback
 ........
for disk in `fdisk -l|grep "Disk /dev"|awk '{print $2}'|sed s/://g`; do
echo "$disk" && smartctl -d ata -a "$disk" -T permissive|grep -iE 'Device Model:|Serial Number:'
echo "---------------"
done
*Make sure you have smartctl from smartmon tools installed
Sample output:
/dev/sdc
Device Model: ........
Say you have a path like this "/some/path/here with spaces/". If you try to transfer it you will get a message along the lines of:
scp -rp 192.168.0.12:"/some/path/here space/" .
scp: /some/path/here: No such file or directory
scp: space: No such file or directory
You can escape each space but what a pain that is especially if you have multiple spaces in the path.
The simplest way is to use the follow........
convert -append file1.jpg file2.jpg output.jpg
The above is all there is to it.
file1.jpg and file2.jpg are the ones to combine (the order is used)and output.jpg is the combined image.........
The package "mdbtools-gmdb" works very well but I was not able to get the forms working that were part of the .mdb but you can at least view all of the rows and Export to CSV........
Here is the scenario you or a client have a remote machine that was installed as a standard/default minimal Centos 6.x machine on a single disk with LVM for whatever reason. Often many people do not know how to install it to a RAID array so it is common to have this problem and why reinstall if you don't need to? In some cases on a remote system you can't easily reinstall without physical or KVM access.
So in this case you add a second physical or disk or already ha........
In my case I could login with the initial install but I rsync'd everything over while preserving ownership and permissions to another RAID partition and booted from that.was fine before. The problem is that you are kicked out the second you login and the problem was SELINUX for some reason (perhaps it noticed something strange when it was moved to the new partition)
login: pam_unix(login:session): session opened for user root by LOGIN(uid=0)
login: ROOT LOG........
#solution
Edit /etc/yum.repos.d/openvz.repo
For the first two entries comment out #mirrorlist and uncomment #baseurl and then it worked
openvz yum problem Centos 6.5 cannot find file on mirror:
yum update
Loaded plugins: fastestmirror
Determining fastest mirrors
* openvz-kernel-rhel6: mirrors.ustc.edu.cn
* openvz-utils: mirrors.ustc.edu.cn
base ........
The solution was to reinstall the vbox dkms package and do a manual modprobe of the modules it makes.
I never sorted out the unable to start due to the USB issue, I did have the guest additions installed but the only way to boot was to change the pointing device from USB to PS2 and then to disable the USB controller (if your pointing device is set as USB, disabling USB will not work because it will re-enable by default when it sees your pointing device is USB, this is w........
Iwas surprised to see that Linux Mint at the latest 17.2 version still has NO mdadm installer option, and worse the installer will not be able to create a proper booting environment even when you do install it.
How to setup mdadm in Linux mint LiveCD
sudo su
apt-get install mdadm
# partition as you need and then create your mdadm devices
# create your SWAP md0
mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/sda1 /d........
Before reading on remember to put the line at the bottom of /etc/sudoers as from experience what happen is that other rules cancel out what you have added.
If your sudoers setup is correct it will work immediately upon saving without requiring a reboot.
Edit /etc/sudoers
yourusername ALL = NOPASSWD: /path/to/command
*Once again remember the above should be on the bottom of the sudoers file or........
First of all this seems to apply to many ONVIF devices
Hard coded IP: 192.168.1.10 (yes not kidding no DHCP!)
00:12:12:9C:C2:00
To view RTSP stream use VLC, or openRTSP or other RTSP capable software:
rtsp://192.168.1.10/user=admin_password=tlJwpbo6_channel=1_stream=0.sdp
user: admin
password: blank
http://ip/Login.htm
Uses Quicktime and is a poor quality picture and slow
Cannot change pass........
sudo apt-get install zoneminder
[sudo] password for one:
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following packages were automatically installed and are no longer required:
libuser-perl python-evince kdebase-apps kwrite unixodbc
libgnomeprint2.2-data python-soappy vgabios python-metacity hddtemp
python-mediaprof........
[ 2868.041375] ata1: EH in SWNCQ mode,QC:qc_active 0x40 sactive 0x40
[ 2868.041554] ata1: SWNCQ:qc_active 0x40 defer_bits 0x0 last_issue_tag 0x6
[ 2868.041556] dhfis 0x40 dmafis 0x40 sdbfis 0x20
[ 2868.041874] ata1: ATA_REG 0x41 ERR_REG 0x84
[ 2868.042013] ata1: tag : dhfis dmafis sdbfis sactive
[ 2868.042163] ata1: tag 0x6: 1 1 0 1
[ 2868.042301] ata1.00: exception Emask 0x1 SAct 0x40 SErr 0x400000 action 0x6 frozen
[........
I never did get it working, it is too bad as obfsproxy should really be an option and integrated into the OpenVPN client and server or something similar:
yum -y install python-pip python-devel
No package python-pip available.
#install the EPEL repo
python-pip install obfsproxy
python-pip install obfsproxy
-bash: python-pip: command not found
pip install obfsproxy
&........
yum -y install wget
wget -P /etc/yum.repos.d/ http://ftp.openvz.org/openvz.repo
rpm --import http://ftp.openvz.org/RPM-GPG-Key-OpenVZ
yum -y install vzkernel vzctl
#enable ip_forward
sed -i s/'net.ipv4.ip_forward = 0'/'net.ipv4.ip_forward = 1'/g /etc/sysctl.conf
#all interfaces should not send redirects
echo "net.ipv4.conf.default.send_redirects = 1" >> /etc/sysctl.conf
echo "net.ipv4.co........
ethtool eth0
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
........
sed -i 's/[d128-d255]//g' file.txt........
This command rips the audio tracks to .wav files
*I recommend making a new directory with the name of the audio disc first and executing everything from within that directory below.
cdparanoia -B
Use the lame mp3 encoder to encode each one with this script:
*Note that this will encode any other files ending in "cdda.wav"
for track in `ls *cdda.wav`; do lame -b 192 $track; done........
if [[ "$templatesource" == *windows* ]]; then
partition=/dev/sda2
fi
The * before and after * windows will match this "Ihavelotsofwindowshere"
Of we could have used "windows*" and anything that starts with "windows" will be matched etc...........
0000:00:00.0 Host bridge: Intel Corporation 5000P Chipset Memory Controller Hub (rev b1)
0000:00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 2-3 (rev b1)
0000:00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 (rev b1)
0000:00:04.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 (rev b1)
0000:00:05.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4........
I'm not sure why I'm getting these but all memory modules are the exact same and all passed memtest successfully although they are ECC. I've heard that ECC RAM can't be tested as well and the kernel seems to indicate they are non-fatl recoverable errors. I wonder if the BIOS has aggressive RAM timing or maybe the controller or motherboard is bad.
[ 12.716515] EDAC MC: Ver: 2.1.0
[ 12.717771] EDAC MC0: Giving out device to........
[ 17.208336] tg3 0000:08:00.0: eth0: Link is up at 1000 Mbps, full duplex
[ 17.210194] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX
[ 76.000065] phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
[ 76.002332] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 86.736004] eth0: no IPv6 routers present
[ 148.960038] phy0 -> rt2x00lib_request_fi........
I messed up the bootloader by accident on a standard Centos 6.3 install because I turned the /dev/vda1 boot partition into an mdadm raid 1. This was all done correctly aside from one point Ididn't realize was an issue metadata=00.90 is the only thing that will allow you to boot (otherwise grub won't work and you won't boot).
So the next step is rescue mode from a CD right? The problem you will find is that grub does not detect your hard drives, this is Ibelieve is be........
The command below will show only files created for the month of 2014-12 but you can of course change the year, month or even specific day or time to suit your needs. The awk command simply just makes it output the list of files created on the date you are looking for.
stat -c "%z %n" *|grep ^"2014-12"|awk '{print $4}'........
if you type Export and see something like this:
declare -x all_proxy="socks://127.0.0.1:22000/"
Most sites assume and tell you to check your .bashrc or /etc/profile /etc/bash.bashrc which may not apply if you've unknowingly or forgot that you setup a proxy from your GUI such as Gnome.
To check in Gnome if you have a permanent proxy do the following:
System -> Settings -> Network Proxy........
Use the program exiftags
exiftags 20141031_155127.jpg-45460829d582e9.jpg
exiftags: couldn't find Exif data........
The solution is to run '/etc/init.d/vboxdrv setup' and sometimes happens when upgrading VBox and the kernel modules don't get upgraded with it. Sometimes the above doesn't work until you reboot because sometimes other unknown processes (even the file manager possibly) may be locking the old module from being unloaded.
Failed to open a session for the virtual machine XP.
The virtual machine 'XP' has terminated unexpectedly during startup with exit code 1.........
You need to use the Samsung driver but specify it as a CLP-360 (this is what I used for my CLP365) and incidentally most of these units look identical on the outside on inside (I've been buying whatever the latest C300 and now 400 unit for years which all seem the same with slightly different features that I never use).
The solution
Once again try specifying earlier models and revisions if the printer doesn't print (it will say it's been sent to the printer bu........
i337 Canada on Bell is hard to root or even install TWRP
Installed TWRP from Odin and my computer gave me the bluescreen at the end but it seemed to be successful (after ODIN said reset).
TWRP mode does not seem to enter, instead you get the Android recovery mode with Volume up + Home
http://galaxys4root.com/galaxy-s4-root/how-to-root-att-or-verizon-galaxy-s4-on-android-4-4-2/
1.)........
Unable to mount iPad 4
Unhandled Lockdown error (-4)
This is because you need the libimobiledevice-utils package installed and a newer version of it.
My older Ubuntu 10.10 uses a version that does not have "idevicepair" which seems to work perfectly and automatically with newer versions of the library.
Basically if you install the above library it should be plug and play and if your imobiledevice-utils doesn't have 'idevice........
CPanel says you can access 98% of the functions through CLI which experienced Unix/Linux admins prefer for simplicity and for scripting. I've never found CPanel easy to use from the admin panel, it seems everything is hard to find and a simple task becomes a series of hunts.
So for people like me here's the list: http://cpanel.net/system-administrators/command-line-scrip........
I've only ever seen this in Ubuntu for some reason and it is because of the /etc/nsswitch.conf settings.
So the issue is that if the hostname's reverse DNS cannot be found that you need to go back to DNS which was not the default in this nsswitch.conf file for some strange reason.
Edit /etc/nsswitch.conf and replace your "hosts" line with this:
#hosts: files dns mdns4_minimal [NOTFOUND=return] mdns........
(echo n; echo p; echo 1; echo 1; echo; echo wq) | fdisk /dev/sdb
The above would make a new partition 1 on /dev/sdb and save the changes to disk, you can of course make changes to do almost anything in fdisk.........
#count=10000 makes an image of 10000MB make sure your image is at least the same as your existing
dd if=/dev/zero of=yourimage.img bs=1M count=10000
# losetup -fv newimage.raw
# fdisk -cu /dev/loop0
# kpartx -a /dev/loop0
# dd if= of=/dev/mapper/loop0p1
# e2fsck -f /dev/mapper/loop0p1
# resize2fs /dev/mapper/loop0p1
# a lot of guides tell you to edit /etc/fst........
./configure
./configure: line 91: cd: /lib/modules/2.6.32-042stab084.25/build: No such file or directory
Error: kernel version not found.
Please make sure your kernel is configured.
dr-xr-xr-x. 4 root root 4096 Feb 21 06:13 ..
lrwxrwxrwx 1 root root 45 Feb 21 06:13 build -> ../../../usr/src/kernels/2.6.32-042stab084.25
drwxr-xr-x 2 root root 4096 Feb 12 20........
Iused the slightly older "304.117" version and it worked.
With the newest version Icouldn't get X to start and kept getting these errors in messages/dmesg.
[ 2346.083660] nvidia 0000:01:00.0: irq 44 for MSI/MSI-X
[ 2350.608342] NVRM: RmInitAdapter failed! (0x12:0x2b:1831)
[ 2350.608354] NVRM: rm_init_adapter failed for device bearing minor number 0
[ 2350.608369] NVRM: nvidia_frontend_open: minor 0, module->open() failed, err........
[3805108.257042] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
[3805108.257052] sd 0:0:0:0: [sda] Write Protect is off
[3805108.257054] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[3805108.257066] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[3805108.257083] sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
[3805108.257090] sd 0:0:0:0: [sda] Write Protect is off........
Kernel panic - not syncing: Attempted to kill init!
Pid: 1, comm: init Not tained: 3.2.51-3.el6.x86_64 #1
Call Trace:
panic+0x8c/0x1a2
forget_original_parent+0x34d/0x360
exit_notify+0x12/0x140
do_exit+0x1d8/0x400
do_group_exit_+0x50/0xc0
sys_exit_group+0x12/0x20
system_call_fastpath+0x16/0x1b
panic occurred, switching back to text console........
wget http://download-location
sudo tar xjvf thunderbird-24.2.0.tar.bz2 -C /opt
ln -s /opt/thunderbird/thunderbird /usr/bin/thunderbird
[sudo] password for one:
ln: creating symbolic link `/usr/bin/thunderbird': File exists
sudo rm /usr/bin/thunderbird
ln -s /opt/thunderbird/thunderbird /usr/bin/thunderbird
The above is how Idid it, if you don't do it properly you'll find that you are still using the old version (........
wget http://download-location
mv /usr/bin/firefox /usr/bin/firefox-old
sudo tar xjvf firefox-26.0.tar.bz2 -C /opt
ln -s /opt/firefox/firefox /usr/bin/firefox
The above is how Idid it, if you don't do it properly you'll find that you are still using the old version (so verify in About that it is the new version). I've verified the above method works perfectly, it's great if you're using an older version of Linux and need to update the most........
Trying to load: pxelinux.cfg/default
boot: _ (why does the cursor flash so long before entering the PXE Boot menu?)........
somestring="309sfjlks39889d"
removelast="${somestring%?}........
shuf -n 1 /path/to/your/file.txt
The above will give you a random line from the file using the "shuf" command.........
Example:
basename /var/log/messages
messages
As shown above the "basename" utility gives you the end filename separately.
dirname /var/log/messages
/var/log
As shown above the "dirname" utlity gives you just the utility even if you pass it a specific file.
The above two utilities are very helpful in Bash scripting when working with files and directories co........
cat Xorginfo.txt|grep -nr "xserver-xorg"
Result:
9: sudo apt-get remove --purge xserver-xorg
13: sudo apt-get install xserver-xorg
17: sudo dpkg-reconfigure xserver-xorg........
./configure
./configure: cannot locate gcc 3.x. please install it or specify with --qemu-cc
yum -y install gcc make
./configure
./configure: cannot locate gcc 3.x. please install it or specify with --qemu-cc
yum -y install compat-gcc-*
./configure
Error: Could not find alsa
Make sure to have the alsa libs and headers installed.
yum -y install alsa-lib-devel
./configure........
sudo mount -o user /dev/sr0 cd
You need the "user"option otherwise non-root or non-owners cannot view the CD and this would make it so no anonymous access to the CD/DVD mount would work. Note that most distributions including Ubuntu DONOT work unless you manually mount and share as shown above (Icouldn't find any other way in Ubuntu).........
Here is a handy script that will check all processes and report what is swapping
#!/bin/bash
for pid in `ps x|awk '{print $1}'`; do
result=`cat /proc/$pid/status|grep VmSwap|awk '{print $2}'|grep -v ^"0"`
if [ ! -z "$result" ]; then
programresult=`ps x|grep $pid|grep -v grep`
if [ $? == 0 ]; then
program=`echo $programresult|awk '{print $5}'|grep -v ^grep`........
mount -o bind /proc /sda2/proc
mount -o bind /dev/ /sda2/dev
mount -o bind /sys /sda2/sys
chroot /sda2
mint / # mount -o bind /proc /sda2/proc
mint / # mount -o bind /dev/ /sda2/dev
mint / # mount -o bind /sys /sda2/sys
mint / # chroot /sda2
mint / # cd ~
mint ~ # ls
Desktop
mint ~ # cd /
mint / # ls
bin Desktop dev-temp home&nb........
Linux box13. 2.6.32-042stab076.5 #1 SMP Mon Mar 18 20:41:34 MSK 2013 x86_64 x86_64 x86_64 GNU/Linux
even setting privvmpages to a specific setting DOES not affect "free -m" in containers.
This is probably a kernel issue
23:36:29 up 159 days, 7:12, 4 users, load average: 0.42, 0.44, 0.33
[root@box13 ~]# free -m
total&n........
GIMP
File - Save As
Microsoft Windows Icon (*.ico)........
This example involves an Aterisk message log of about 26GB, but with any server it usually does not get deleted until the server is stopped/restarted:
asterisk 13729 root 6w REG 0,41 27277943090 59097971 (deleted) /var/log/asterisk/messages
So if you've deleted a bunch of large logs, make sure you restart the server for them to regain your space.
........
/scripts/phpextensionmgr install PHPSuHosin
Updating md5sum list
Fetching http://httpupdate.cpanel.net/cpanelsync/easy/targz.yaml (connected:0).......(request attempt 1/12)...Resolving httpupdate.cpanel.net...(resolve attempt 1/65)...
Fetching http://httpupdate.cpanel.net/mirror_addr_list (connected:0).......(request attempt 1/3)......connecting to 74.50.120.123...@74.50.120.123......connected......receiving...100%......request success......Done........
convert check.png -resize 25%x25%! check-resize.png
You can use a percentage or pixel sizes.........
The first is a dual CPU AMD Opteron 2373EE (4 cores x 2) and I think it did bad because it has some old 250GB SATAs which can only do about 65MB/s max sequential reads. I think it should have blown away the second (AMD X4 640 Quad Core).
[root@fs12home unixbench-4.1.0-wht-2]# ./Run
make all
make[1]: Entering directory `/root/unixbench-4.1.0-wht-2'
Checking distribution of files
./pgms exists
./src exists........
htpasswd -b -c filename username "password"
-b = take the password that we specify in the command (don't prompt for it)
-c = create the filename
username=username
password=password (I use quotes because it breaks if you use special characters)........
One thing to remember is that you need MegaCli to do the flashing.
You also need the correct file,I tried at least 2 different Perc 6 firmwares from Dell that kept getting rejected as corrupt by MegaCli(they were really the wrong version). I have an external PCI-E Dell 6 Perc/I butI chose images from the 'Integrated" on motherboard version as it was allI could find. They are different, and below is my first time finding success.........
I flashed an LSI Logic firmware to it and it broke the BIOS (cannot do Ctrl+R) for booting purposes but allows other functionality to work normally.
I tried downgrading to a Dell firmware for Perc 6i but it won't work, not even with MegaCli
wget http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN
--2013-08-26 12:53:39-- http://downloads.dell.com/FOLDER00416606M/1/SAS-RAID_Firmware_W83M2_LN32_6.3.1-0003_A14.BIN
Resolvi........
LSi Megaraid
At first it was configured as a RAID 0, then I deleted the Virtual Disk Group.
I thought both drives would be shown and detected in Linux as sda and sdb but it actually shows nothing.
To make them work you have to hit Ctrl+R before the system boots (when prompted) and create a Virtual Disk Group. In my case I created each one as RAID 0 (with a single drive only) as I just wanted JBOD but there is no such option or default in these Dell Pe........
cp -L index.php index.php-2013-08-21
The -L switch is what you need because it's a huge issue if you think you've copied a file for backup purposes but it really just creates a symlink to the original file.........
The key here is to use the "uuencode" command but note that we specify the file name twice (this must be done at least on Centos or it won\'t work).
The first file.zip is the actual file we want to send.
The second file.zip i........
package kernel-xen-2.6.18-274.7.1.el5.x86_64 is intended for a x86_64 architecture
Linux etc 2.6.18-274.7.1.el5xen #1 SMP Thu Oct 20 17:06:34 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux
As you can see above architecture and kernel is 64-bit but I had to force it to install using "--ignorearch"
Solution
#rpm --ignorearch -ivh kernel-xen-2.6.18-274.7.1.el5.x86_64.rpm
Preparing...&nb........
Use imagemagick:
convert -density 200 file.pdf file.jpg
Increase the "density" value to get a higher resolution/larger file an decrease it to go smaller.
This is really the quickest and simplest way.
Some issues you may have:
http://realtechtalk.com/ImageMagick_Convert_PDF_Not_Authorized-2217-article........
Another new drive bad from the start:
Jun 2 15:14:18 one-desktop kernel: [15895.386779] ata2.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen
Jun 2 15:14:18 one-desktop kernel: [15895.386782] ata2.00: irq_stat 0x08000000, interface fatal error
Jun 2 15:14:18 one-desktop kernel: [15895.386784] ata2: SError: { UnrecovData HostInt 10B8B BadCRC }
Jun 2 15:14:18 one-desktop kernel: [15895.386788] ata2.00: cmd 60/0........
ffmpeg -vcodec copy -i 20130526_195809.mp4 -an 20130526_195809-noaudio.mp4
Withotu the -vcodec copy I got this error (so make sure you use the vcodec copy switch): Error while opening encoder for output stream #0.0 - maybe incorrect parameters such as bit_rate, rate, width or height
........
find / -name 'thedirectorytofind' -type d
That's all there is to it and now you don't have to get a listing of all the files along with it.
Another cleaner solution that supports wildcards is the following
find prep-*/dvd-slideshow_temp*/ -type d
........
This is just trying to read 5GB off the drive with dd and the drive initially tested ok but shortly after I wondered why I was seeing 2MB/s read speeds. Notice the "current_pending_sector", anytime I've seen it at anything above 0 even with no other bad fields/attributes, it means the drive is bad.
ata1.00: exception Emask 0x0 SAct 0x3 SErr 0x0 action 0x0
ata1.00: irq_stat 0x40000008
ata1.00: failed command: READ FPDMA QUEUED
ata1.00: cmd 60/00:00:........
After some fsck issues I can't boot my Centos 6.4, this just keeps repeating over and over.
init: tty (/dev/tty2) main process (1031) terminated with status 1
init: tty (/dev/tty2) main process ended, respawning
Disabling SELinux through Single User mode fixed this.........
This is something many people and especially businesses worry about, or at least they should. Before throwing away a hard drive, returning a hard drive, or especially Warrantying/RMAing it, you should wipe the drive.
Linux provides the "shred" and "dd" utlities which work quite well. It seems even a single pass is good enough but by default shred will do 3 passes.
Here's an example of using shred in Linux (I use a custom made distribution from........
I find it very annoying that this mouse has buttons on the side where you grip it and the left one goes back in the browser and the right one goes forward. Imagine if you're filling out a form and hit it, most forms/websites have no protection against it.
Source: http://ubuntuforums.org/showthread.php?t=2065400
Here's how I fixed it with xinput, it's too bad there's no good standard GUI to........
smartctl -a /dev/sda
smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: ATA WDC WD1600YS-01S Version: 20.0
Serial number: WD-WCAP03024940
Device type: disk
Local Time is: Mon Apr 29 21:40:07 2013 PDT
Device does not support SMART
Error Counter logging not supported........
If you move your hard drive(s) around to other computers/servers, you'll find that your eth0 keeps getting higher, the first time it will become eth1 and then eth2 etc and even higher if your server has dual or quad NICs. The reason is that udevd basically assigns eth0 tot he first NIC it finds and remembers it, if it encounters a NIC with a differentMAC, it assigns it one higher (eg. eth1).
See the example below, I have eth2 now so how doI fix it?........
Kernel panic - not syncing: Attempted to kill init!
Pid: 1,comm: init Tained: G I------------- 2.6.32-358.el6.x86_64 #1
Call Trace:
[] ? panic+0xa0/0x16f
[] ? do_exit+0x862/0x870
[] ? fput+0x25/0x30
[] ? do_group_exit+0x58/0xd0
[] ? sys_exit_........
-bash-3.1# shutdown -rn now
Connection to localhost closed by remote host.
Connection to localhost closed.
Sometimes I work with embedded systems/custom kernels without any of the fancy init scripts and other common Linux basics that most would expect. This means that often the "reboot" command (which uses an init script) will never work, not only that but it will hang the server and a manual power cycle or reboo........
start=1
increment=5
lines=`cat linesfile.txt|sed -n "$start","$increment"p`
The secret here is the power of sed.
Basically the example above would take the first 5 lines from the file. You could change it though to say take 20 lines starting from the 5th line by adjusting the start and increment values.........
Solution To The Following:
yum -y install zlib-devel
yum -y install e2fsprogs*
*** Cannot find /usr/include/et/com_err.h. (yum install libcom_err-devel) ***
Installation didn't pass, halting install.
Once requirements are met, run the following to continue the install:
cd /usr/local/directadmin/scripts
./install.sh
Common pre-install commands:
http://help.directadmin.com/it........
Here's a proven example of what a bad hard drive can do, it was technically functioning OKin a RAID array but the system became extremely low and the load become high and IOWAIT was even higher and I always thought it was a bad application. The truth is that this failing 1TBHitachi has slowly gotten worse and caused huge slowdowns, (eg. 100% load on Thunderbird waiting for e-mails to load etc..). After swapping it out, tabs change instantly, emails are not lagged, and........
Install unoconv
unoconv -d document -f pdf file.doc
Change "file.doc" to the name of your document. Note you could specify *.doc and it will convert all .doc's in the current directory to pdf which is very handy.
unoconv uses the cli from OpenOffice to do this, OpenOffice actually doesn't have an easy way I've found of doing this despite it having the functionality.
........
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
For whatever reason it seems the r8169 driver that ships and has shipped with most Linux distros for years is still flawed and does not work properly on these cards, causing 100mbit connectivity when it should be 1gbit and even worse, causing random network dropouts. The r8169 driver in Linux kernels is simply not meant to be used on th........
Usually a lot of things don't work right on Linux, but Samsung printers aren't one of them. I used to have a CLP310N that never worked right in Linux, it would print strange lines over pictures or with some programs, no picture at all. I was using whatever the default driver that Ubuntu found.
Now I upgraded to a CLP-365W which is basically the same thing with wireless but no driver from Ubuntu (eg CLP-350) works. I was forced to go to Samsung's site and was surprise........
This pops up when connecting the phone and it doesn't seem to charge. The phone keeps showing a status message every few seconds "Connected as a media device".
It's ridiculous why this phone doesn't just default as a simple USB Mass storage device.
Here's what I see in /var/log/messages:
Jan 30 18:51:27 QuadCoreAM2 kernel: [18038228.144046] usb 1-3: new high speed USB device using ehci_hcd and address 24
Jan 30 18:51:28 QuadCoreAM2 ke........
I like badblocks and don't know a better more reliable way of checking the drive. If there are no errors from badblocks and dmesg doesn't produce any SATA related errors, the drive should be good (for now at least).
I also prefer to do read and write mode, yes it takes ages but it is really the best way of doing it. This gives me the most confidence in knowing that a drive, especially a new one is at least OK at the moment.
To test in read only mode........
This booting error is because the Xen PV guest image uses the Xen kernel, this is not compatible with anything but a host running a Xen kernel.
I did a kpartx -av virtual.img and then it created some partitions that showed up in fdisk.
I mounted it and did a chroot into it and removed the xen kernel and installed a normal kernel but Xen still shows the same kernel in Grub (only the Xen one).
This is strange but it seems like this Xen PV guest has some sort of hidden or........
Inever started these processes but they are from a custom based bootable Linux I've made and I've never seen this behavior on other machines or even with the same machine using different kernels. These processes seemed to spawn on their own and I have no idea why and even worse why the CPU usage is so high?
Here's the output from top:
907 extaudit 30 10 0 0 0 R 90.7 0.0........
arp -a
syst (192.168.1.122) at 21:96:43:3a:62:a2 [ether] on eth0
arp -d 192.168.1.122
If you get an error do:
arp -d 192.168.1.122 -i eth0
Sometimes the arp cache just won't clear either, some say it should automatically but there are cases where the above doesn't work. I believe it may be that some network applications are keeping the entry alive but this is just a guess.........
This is very handy if you're too busy and don't have time to download whatever files you need.
The -D specifies the domains allowed, this is because I specified -H which means foreign hosts are allowed, if you don't restrict them you'll end up going to the whole internet via ads and other links just like a search Engine would follow.
-l 0 specifies to go deep, to as many levels as possible/as exist.
-e robots=off is important because robots.txt often says you can't vie........
This is something I often setup for clients because it's very helpful for people in datacenters, this allows custom OS installs on demand, you can customize it more by using kickstart etc.. but here's a base I use before customizing more:
This little script below will install everything you need to get booting by PXE Linux.
It also assumes you set a local IP (be sure not to overwrite your existing IP) on eth0:0 (note the :0) as 192.168.1.10 and it........
The best way is to use rsync, I've set it up so it doesn't copy unnecessary files, or at least ones I'm sure aren't needed.
Here is the rsync command Iused (adapt to your specific Thunderbird profile location):
rsync -hazv user@remotehost.com:/home/user/.thunderbird/sbrer.default/* /home/user/.thunderbird/4nyb0.default/ --exclude=global* --exclude=Cache --exclude=ImapMail --exclude=Mail
This is a great way to get your e-mail accounts going on a new c........
Here is a quick script that works on most Centos versions to disable the virus/SELinux from blocking basic functionality.
The first echo 0 statement disables SELinux instantly but it will still be enabled on reboot.
The second line disables it permanently.
#!/bin/bash
#disable SELinux Immediately
echo 0 > /selinux/enforce
#disable SELinux Permanently
sed -i 's/SELINUX=enforcing/SELINUX=disabled/g' /etc/selinux/config........
parted sdc.img
GNU Parted 1.8.8
Using /home/one/sdc.img
Welcome to GNU Parted! Type 'help' to view a list of commands.
(parted) unit&nb........
ip_conntrack: table full, dropping packet.
A lot of clients I've seen have this issue, it really seems the default level is way too small. Once this connection tracking table becomes full then packets get dropped which is obviously a bad thing.
One thing to be mindful of though is that 350 bytes of memory are used per entry so there is some justification for not keeping it too high. However, if you have multiple servers running or high traffic daemons........
A lot of people become nervous (and understandably so) when checking their auth or security logs, in Centos /var/log/secure and see dozens, hundreds of even thousands of attempted logins to various services, especially SSH.
Of course you could manually block these people/IPs but no one has time to read the logs like that, what if some program or script could do it for you?
This is what denyhosts does for you, it checks the logs and based on a certain number of failed SSH attem........
00:14.2 Audio device: Advanced Micro Devices [AMD] Hudson Azalia Controller (rev 01)
00:01.1 Audio device: Advanced Micro Devices [AMD] nee ATI Device 9902
Backup your also.conf file
cp /usr/share/alsa/alsa.conf /usr/share/alsa/alsa.conf.bk
Change all instances of "card 0" to "card 1" (no need to manually do it, this command below does it all instantly and without fail or error:........
Disk /dev/sda: 320.0 GB, 320072933376 bytes
256 heads, 63 sectors/track, 38761 cylinders
Units = cylinders of 16128 * 512 = 8257536 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 38........
This is just how I like things, quick and simple through CLI (command line) using gifsicle for free.
gifsicle --colors 256 --delay=200 --loop banner.gif banner-page2.gif > banner.gif
banner.gif = the first page of the banner
banner-page2.gif = the second page
--delay=200 ms to switch between the two
--loop=it goes back and forth between the two pages forever
banner.gif=the resulting animated gif.
There are many other opti........
In bash you test like this for problems that can be caused by non-printable characters since if you don't know how to identify it because it basically breaks your script.
echo "url=$url" should print something like this normally if you have properly formatted input/text:
url=::http://someaddress.com::
But if you have some weird hidden characters (not visible in a text editor of any sort you'll get something like this
::l=::http://s........
I've encountered this problem before and I believe it may affect other drivers (I could test but I don't have time). This was happening on my custom Linux system with the pcnet32 driver.
pcnet32: eth0: transmit timed out, status 97fb, resetting (and some other kernel module tracing in dmesg)
Basically it means the card is connected (it shows connected in full duplex etc.. and recognized if the cable is disconnected too) but no packets can be sent or received........
I admit I didn't know you could do this for the longest time and is an annoying feature of screen.
In order to scroll up and down just hit "Ctrl+a+Esc" or "Ctrl+a+[" and then you can Pageup, Pagedown and using the arrow keys.........
For years I've always built cheap systems believing that there is little difference in more expensive components when it comes to reliability and quality, I generally believe this still except for Power Supplies.
I've always bought cheap cases with nice sounding 350-550W stock/cheap/crap power supplies and haven't had any issues for the most part until recently.
One such case is an NGEAR case with a 550W Optimax power supply, I always read that these supplies don't produce the........
I've thought for awhile that Asus has been banking on its years old reputation for quality amongst gamers and enthusiasts and I think I'm right. My Asus VE247H Monitor with a supposed 2MS refresh rate has 1 red/stuck/dead pixel but fortunately it can only be seen on a non-true black picture or against a blue screen.
I have several Asus products and find they're all of fairly poor quality. First of all their motherboards have given me the most issues of any brand, they te........
I'm running Ubuntu 10.10 with Asus NVIDIA GT430
2.6.35-32-generic-pae #65-Ubuntu SMP Tue Jan 24 14:06:16 UTC 2012 i686 GNU/Linux
Nvidia binary driver: 260.19.06
The screen sometimes completely freezes and locks up or everything starts going very slow:
[1903398.100007] NVRM: os_schedule: Attempted to yield the CPU while in atomic or interrupt context
[1903402.373210] NVRM: Xid (0001:00): 53, CMDre 00000000 00000080 00000000 00000005 00........
fdisk -lu VPS.img
last_lba(): I don't know how to handle files with mode 81ed
You must set cylinders.
You can do this from the extra functions menu.
Disk VPS.img: 0 MB, 0 bytes
255 heads, 63 sectors/track, 0 cylinders, total 0 sectors
Units = sectors of 1 * 512 = 512 bytes
Device Boot Start End ........
One of my test Centos 5 containers was on a partition that filled up and it threw all sorts of errors and stopped responding but now I can't boot it again anymore.
All the console shows is the Linux Penguin on the top left corner and the xm console says "usbcore: registered new driver hub" and has halted there.
Centos 5 Xen container stuck/frozen won't boot on "usbcore: registered new driver hub"
Another great way of troubleshooting is booting fro........
This was very annoying but has a simple fix, I had an echo and the voice quality was absolutely horrible (it sounded like tin cans under water) if that helps describe it. It was extremely distorted.
The simple Skype sound quality solution
Go to "Options" -> "Sound Devices"
Disable the "Allow Skype to automatically set my mixer levels"
After doing this the sound qua........
I dread updating the kernel and rebooting to find the Ubuntu graphics aren't working and you have to manually intervene. This is usually because Ubuntu for whatever reason didn't update the drivers you need (eg. the manually compiled Nvidia Kernel driver that MUST be recompiled for each and every kernel update unfortunately).
The most common reason may be that "linux-source" hasn't been installed automatically on my system. I tried to manually reinstall the........
I really am a Linux fan but my comments here may not show it. Although I'm quite familiar with Linux CLI to administer servers, I find Linux GUI OS's like Ubuntu at times very clunky.
This is partially because there's no such thing as a "self-made" Linux from scratch where the UIwas designed by a single team. Linux is made up of several different projects that are generally completely separate and this lack of integratiion is a key issue that makes things f........
It really is as simple as:
cdrecord -v dev=/dev/sr0 pathtoyourisoimage.iso
-v is for verbose, I prefer it but if you don't you won't see as much output like below (I like to know the details and exactly what's happening)
dev=/dev/sr0 specifies the device name of your burner (they say not to use it and to specify some weird annoying device string but using the raw /dev has always worked for me and is how it should have been implemented from the start IMHO)........
Visit http://linux.softpedia.com/get/Programming/Interpreters/Android-32340.shtml
Basically copy and paste all of that below and you'll have installed and started the Android SDK before you know it.
wget http://dl.google.com/android/android-sdk_r12-linux_x86.tgz
sudo apt-get install openjdk-6-jre openjdk-6-lib openjdk-6-jre-headless
tar -xvf android-sdk_r12-linux_x86.tgz
cd android-sdk-linux_x86/tools
./android........
gocr works great and it's simple, just invoke it like so:
gocr filename.png
The output will be printed to the screen.
My only complaint/concern is that even with standard terminal output (not scanned) from a printscreen, gocr does make mistakes by inserting extra spaces where they don't belong, mistaking letters for numbers etc.. but it's definitely enough to be readable and figure out what you're looking at.
I haven't tested yet with scanned input........
These were caused by a bad stick of Corsair RAM
[] free_hot_cold_page+0xfc/0x150
[] __pagevec_free+0x14/0x1a
[] release_pages+0x127/0x12f
[] __pagevec_release+0x15/0x1d
[] __invalid_mapping_pages+0x120/0x156
[........
carat M isn't this symbol ^ that you think, it can only be produced by typing "Ctrl-v, Ctrl-m". That you might see in text files saved from Windows.
tofrodos is the package that has dos2unix which is basically the same scripts that replace ^M with /n
tofrodos is the Debian/Buntu package name which has the dos2unix and unix2dos binaries........
It may be hard to find by Googling by it's really quite simple and quicker than reading dozens of man page entries.
sed -n 5p somefile.txt
Just replace the 5 with whatever line you want to be printed.........
dd if=/dev/sda of=/dev/null creates ever increasing load every second.
After minutes the load has moved up to 4.79
I've tried with two different discs in my system.
I wonder if it's a delay or problem with the SATA bus because one drive I have connected has recently failed.
I notice when drives fail that you get some IO/blocking issue when they don't respond properly.
Yes I believe it was, because here's the same disc after removing the dead........
I had a system running a 128MB live CD image with 2.8 gigs of available RAM and the OOM kernel killer went crazy when using dd for more than 8 minutes and kept killing everything. I've read that this is due to a low-memory issue and paging in the kernel and 32-bit systems with lots of RAM.
I even enabled swapspace on my LiveCD and the issue happened 25 minutes into dd rather than 8 minutes, so what gives?
Also no swap space was ever used!
cat /proc/s........
I like dd, although it only reads it, usually a read test of the entire disk will uncover if your hard drive is bad in some parts. This is a good thing to do at least once a month, a lot of times bizarre program behavior, laginess and crashing/unnmounting problems etc.. are due to a failing disc and SMART won't know it or indicate a problem:
We must also remember there's never a guarantee, I've found that ever since we moved to larger and more platters per drive with 1TB drives........
I had one of these shipped and it was not recognized when plugged in, here's what a dead drive looks like (I assume it's teh circuit board which is dead):
ata1: link is slow to respond, please be patient (ready=0)
ata1: softreset failed (device not ready)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1: link online but device misclassified, retrying
ata1: link is slow to respond, please be patient (ready=0)
ata1: softreset f........
I thought only a faster CPUand SSDwould help but I already have a Quad-Core CPU and it wasn't being maxed out. The actual tests were performed on an AMD-V enabled 128MB dual core VMWare container though.
There is a flag that can be passed to make in order to start multiple threads, by specifying 4 threads I was able to reduce the whole kernel compilation time from scratch by about 50%! (65minutes vs 31minutes!). *Yes I did do a make clean before each co........
Normally if you're in a certain directory you could do:
find *.txt and it will work as expected, but it won't work recursively through child directories, here's the correct way to do it:
find . -type f -name *.txt
The "-type f" is optional because that means only files, but we could have specified d for directory etc...
The above command will work recursively as you'd expect. In that way I find "find" to be un........
In file included from drivers/block/cciss.c:1015:
include/asm-generic/pci-dma-compat.h: In function `cmd_special_free':
drivers/block/cciss.c:196: sorry, unimplemented: inlining failed in call to 'cciss_tag_discard_error_bits': function body not available
include/asm-generic/pci-dma-compat.h:25: sorry, unimplemented: called from here
make[2]: *** [drivers/block/cciss.o] Error 1
make[1]: *** [drivers/block] Error 2
make: *** [drivers] Error 2........
I found this technique listed in many places which shows you how to use a common Linux tool "dd" to dump the raw partition of your iPhone.
I give credit to this site for showing me the correct way to dd from the iPhone, I never thought to try it in the other direction:http://log.ijulien.com/post/182804914/iphone-3gs-data-recovery
Requirements
1.) Jailbreak your........
I was afraid to remove the virtualbox 3.2 package in Ubuntu because I didn't know if it might remove the .virtualbox folder which contains all of my VM data.
I have a backup soI did remove the package and found everything was intact, so I installed and upgrade to VBOX 4.0 which seems to be a huge improvement, especially in UI performance.........
http://www.splitbrain.org/blog/2010-06/15-linux_ocr_software_comparison
They did a great writeup and comparison on the different OCR options available for Linux.........
smartctl -t long /dev/sda (note you can specify short, but it's not as thorough as long of course).
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Extended self-test routine immediately in off-line mode".
Drive command "Execute SMART Extended sel........
high IO wait
424 root 39 19 1900 848 552 D 0.0 0.0 0:00.91 updatedb
root 424 0.0 0.0 1900 848 ? DN Mar11 0:00 /usr/bin/updatedb -f sysfs?rootfs?bdev?proc?cpuset?binfmt_misc?debugfs?sockfs?usbfs?pipefs?anon_inodefs?futexfs?tmpfs?inotifyfs?eventp........
kernel 2.6.27.54
Fusion MPT base driver 3.04.07
Copyright (c) 1999-2008 LSI Corporation
Fusion MPT SPI Host driver 3.04.07
mptbase: ioc0: Initiating bringup
mptbase: ioc0: WARNING - Unexpected doorbell active!
mptbase: ioc0: ERROR - Doorbell ACK timeout (count=4999), IntStatus=80000001!
mptbase: ioc0: ERROR - Diagnostic reset FAILED! (102h)
mptbase: ioc0: WARNING - NOT READY!
mptbase: ioc0: ERROR - didn't initialize proper........
xmessage "Your message here" -display :0
This will popup a window with the message, it would be cool if it allowed two way communication though.
I found the info in this post: http://en.andregondim.eti.br/?p=72........
Use "ImageMagick" which can be installed easily on most UNIX/Linux distros.
Remember that it will go with the standard file listing to determine the order but I believe you can manually specify multiple jpg's in the arguments.
Convert image/jpg to PDF
convert *.jpg yourpdf.pdf
This is a very handy and free tool.
Convert DOC/TXT documents to PDF
If you wanted to convert a .doc file or text........
Convert MBOX Mail files into Maildir using Linux
*You need perl an the TimeDate module
Get the free Perl script mb2md from the project/author's site:
wget http://batleth.sapienti-sat.org/projects/mb2md/mb2md-3.20.pl.gz
gunzip mb2md-3.20.pl.gz
#remember you need timedate or you'll get this error:
./mb2md-3.20.pl
Can't locate........
Webmin Setup Centos 5:
wget http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html&ts=1294339690&use_mirror=surfnet
[1] 24229
[2] 24230
[root@host ~]# --2011-01-06 21:48:20-- http://downloads.sourceforge.net/project/webadmin/webmin/1.530/webmin-1.530-1.noarch.rpm?r=http%3A%2F%2Fwww.webmin.com%2Fstandard.html
Resolving downloads.sourceforge.net... 216.34.181.........
That is pinging to the gateway IP on the same switch, the same IP is pingable externally without any problems which makes me think the switch is fine.
64 bytes from 55.55.55.55: icmp_seq=4 ttl=255 time=1.07 ms
64 bytes from 55.55.55.55: icmp_seq=1 ttl=255 time=3536 ms
64 bytes from 55.55.55.55: icmp_seq=2 ttl=255 time=2536 ms
64 bytes from 55.55.55.55: icmp_seq=3 ttl=255 time=1536 ms
64 bytes from 55.55.55.55: icmp_seq=8 ttl=255 time=1.20 ms
64 by........
Install the "Editors" and "Net" groups that will give you rsync, ssh, ssh-keygen and cron.
The trickiest thing that I keep forgetting about each time is you have to run "cron-config" which adds the cron service to Windows, and without doing that obviously no cron jobs will be run thus making automatic backups impossible.
Warning about rsync/cygwin and using the -a archive switch.
It's a good thing I caught this because it doesn't work ri........
There's no partial WD EARS alignment fix:
I had data on /dev/sda3 and /dev/sdb3 (RAID1) so I couldn't edit that one.
I thought I'd be smart and try fixing the first two partitions so I set the first one starting at sector 2048 and then +8 for the second partition.
This has really slowed the performance down worse than it ever was!
Disk /dev/sda: 2000.4 GB, 2000398934016 bytes
255 heads, 63 sectors/track, 243201 cylinders, tot........
yum exits in the middle
The problem is this VPS seems to be an OpenVZ template from HyperVM. The only way to make it work was to disable i386 packages since this was an x64 kernel. That shouldn't be necessary but it was the only way to make yum stop quitting after the first package or two. I couldn't find any issue by checking the logs either.
echo y|yum install vim-minimal telnet expect jwhois net-tools slocate iptables elinks gawk
L........
I separated the 2 drives in the RAID 1 array.
1 is the old one /dev/sda and is out of date, while the separated other one /dev/sdc was in another drive and mounted and used with more data (updated).
I wonder how mdadm will handle this:
usb-storage: device scan complete
md: md127 stopped.
md: bind
md: md127: raid array is not clean -- starting background reconstruction
raid1: raid set md127 active with 1 out of 2 m........
This is an easy fix and highlights a huge issue again with Linux and Flash still not playing nicely/working as well as Windows yet.
Solution - Go to "about:config" and disable the two entries (set them to false):
dom.ipc.plugins.enabled.libflashplayer.so
dom.ipc.plugins.enabled.libnptest.so........
Virtually no system has a floppy disk drive anymore but you will often find your Linux distribution insists that you do or should have one :)
The solution is to remove the floppy module and prevent it from loading on the next reboot.
rmmod floppy
Centos/RHEL
echo "blacklist floppy">> /etc/modprobe.d/blacklist
#update initramfs so it takes effect
dracut........
Remember to replace "eth0" with your NIC device although usually it will be eth0.
Replace 192.168.1.1 with your default gateway, remember you can also add multiple gateways by adding a second/different default gateway.
route
Kernel IP routing table
Destination Gateway Genmask&nb........
Create New RAID 1 Array:
First setup your partitions (make sure they are exactly the same size)
In my example I have sda3 and sdb3 which are 500GB in size.
mdadm --create /dev/md2 --level=1 --raid-devices=2 /dev/sda3 /dev/sdb3
mdadm: array /dev/md2 started.
Check Status Of The Array
*Note I already have other arrays md0 and md1.
You can see below that md2 is syn........
In Ubuntu when quoting in a forum that would include a left < bracket it often appears garbled as a box with 003C inside.
Also with phpbb anything inside the "code" field appears garbled and as gibberish.
For some reason I can't find anyone else complaining about this and have not found a solution for it, but it's very annoying.........
This happens on some systems due to a video issue with Intel Videocards, after you see the kernel load you may see almost immediately that you get a black screen.
The following kernel parameters usually solve it:
nomodeset i915.modeset=0 xforcevesa
some people just use "nomodeset" and others use "i915.modeset=0". I think nomodeset may also do the same for each video driver so it may imply i915.modeset=0 anyway but I am not sure.........
You'll see the following and the boot process will freeze:
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
I have struggled with this issue on vari........
I am a huge fan of Linux and the idea of OpenSource but I've said it many times, there are still hurdles in today in 2010 for Linux as a Desktop. Linux is still intended for servers at its very core. This can be changed succesfully though, as Apple has shown us with Mac OS X based on FreeBSD.
Half of the issue is lack of driver support and the other half is the Linux Kernel and Window Manages, KDE and GNome still both don't cut it (but they're getting closer).
I'll........
This error is annoying, in a Virtuozzo KB entry about this ip tables nat problem they say the kernel needs to be ugpraded:
Symptoms
The node runs 2.6.18-x kernel older than 2.6.18-028stab053.10.
NAT module does not work in container, you get "can't initialize iptables table 'nat'" error:
# iptables -t nat........
For a standalone system the solution is simple, just use the same version of Windows a copy a good version of:
C:windowsSecurityDatabasesecedit.sdb from another computer.
Then you should be able to login again without getting the nasty message "Local policy does not permit you to log on interactively."
Of course you will probably need a way of accessing the filesystem off-line in order to get to it such as a Linux boot disc.
Some........
Mencoder is great, you can throw anything at it, including video files from your camera and have it encode into xvid or almost any other format.
In my case I took 640x480 video from my Canon and reduced the size by 1/3 with the options below (there are many other options that you can read about in the manual but I like to keep it simple).
Mencoder Encode
mencoder -ovc xvid -oac mp3lame -xvidencopts fixed_quant=4 -o ........
catdoc.i386 : Decodes MS Word files into plain text or TeX format
I haven't figured out how to use it, it is really not clear or obvious but it should do the job if you can figure it out.
Usage:
catdoc [-vu8btawxlV] [-m number] [-s charset] [-d charset] [ -f format] files........
If you have the "(auto-read-only)" beside an arrayI have no idea why that happens but it is easy to fix.
Just run "mdadm --readwrite /dev/md1" (rename md0 to the device with the problem and it will begin to resync.
md1 : active (auto-read-only) raid1 sdb2[0] sda2[1]
19534976 blocks [2/2] [UU]
resync=PENDING
........
I finally decided to look into some utils that did this, and the first one I found is "mp3burn". It is unbelievable simple and perfect. *2017-11 update and mp3burn is still available in standard repos such as Ubuntu 14/16 so this is a current and working project.
Just install the package and it gets all required libraries to convert and then burn's on the fly. And you won't believe how simple it is.
I just want to a directory that had the MP3's I wanted t........
This is obviously a bug in the r8169 kernel module and it seems to affect a lot of people. I upgraded to the latest kernel and hope this won't happen anymore, as it is a very serious error. This is especially serious for those who are running servers with this chipset, who can afford for the NIC to randomly go off-line for no apparent reason?
[655548.189113] type=1505 audit(1277067560.902:5): operation="profile_load" name="/usr/bin/freshclam&q........
This is a great way to use your ftp server space, for example on your web hosting account (althoughI believe many hosts don't allow storage like this), but if you have a VPS/Dedicated Server etc.., this would be perfect. Imagine how easy it is to work with an ftp account that you can just mount as a normal partition or directory in Linux, it would be great for backups etc..
Name
curlftpfs - mount a ftp host as a local directory
Synopsis........
*Note OS X is strange to install, I thought my HDD was not being detected by you just have to go to Diskutil and create a partition for the root filesystem and then close/move the Window and proceed with the install.
After install Mac OS X 10.4.6 Tiger I get a black screen that says:
b0 error
Most people say the partition has to be marked as "active", actually that just means marked as "bootable". Instead of t........
This is based on Debian Linux but should apply equally to any *nix distro.
Install LUKS/crypt-setup
apt-get install cryptsetup
Setup your LUKS Partition
Of course change /dev/md2 with whatever partition you intend to use LUKS on.
cryptsetup --verbose --verify-passphrase luksFormat /dev/md2
You'll be asked to verify your decryption password twice
*DO NOT FORGET THIS PASSWORD AS IT IS NOT RECOVERABLE!........
I've never understood how to enable and disable services for different run levels in Debian based distros, it's just weird, annoying and doesn't make sense. I much prefer chkconfig from RHEL.
Just install the package called 'rcconf' and be done with it. rcconf makes things easy for you.
apt-get install rcconf
Reading package lists... Done
Building dependency tree
Reading state information... Done........
I'm using Ubuntu 8.04 but anyone using older kernels will find this may apply to them. My Intel graphics are very slow with the default Xorg settings but by using "EXA" acceleration, scrolling down windows of text becomes pretty snappy.
Just edit /etc/X11/xorg.conf
Section "Device"
Identifier "Configured Video Device"
&nb........
I was creating a RAID array and got this error: mdadm: /dev/sda1 is too small: 0K
mdadm: create aborted
Of course sda1 is not too small, both partitions sda1 and sdb1 are identical in size:
Disk /dev/sda: 2000.3 GB, 2000398934016 bytes
255 heads, 63 sectors/track, 243201 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000
Device Boot Sta........
I wasted a lot of time wondering why I could never find those packages.
Check the /etc/yum.conf file and at the bottom look for the "exclude=" line.
Below is what I found in mine
exclude=apache* httpd* mod_* mysql* MySQL* da_* *ftp* exim* sendmail* php* bind-chroot*
Just remove those entries or uncomment that line and you'll get access to the missing applications.........
Partclone is a great tool that is basically like dd only it does not waste space, it doesn't take the whole partition, yet it does the same thing as dd, only with huge space/cost savings.
Clonezilla uses partclone and is more of an integrated/easy to use suite I guess you could say. I've personally only used partclone but I wish there was an easy way to mount partclone images.
I believe with Clonezilla you can do that, so I will probably give it a shot next time.........
I'm not impressed with this motherboard, I was impressed with my Gigabyte AM3 board which seems to work flawlessly.
Everyone knows that the firmware is flawed, even though I have the F6, it still seems that the system doesn't reset properly or quickly enough.
Another HUGE problem is that in most Linux kernels the NIC won't work (if you try 10 times by rebooting it might). I also notice that you need to power down for it to work.
This board does not seem very com........
This function and others may not work with the stock PHPinstall on Centos/CPanel: Fatal error: Call to > undefined function imagecreatefromjpeg()
Even with libjpeg-devel installed it won't work because PHP was not compiled with jpeg support, so we have to do the dirty work ourselves :)
Here is the command/yum's I did to install missing libraries for PHP that configure will complain about (yes it is a one by one process).
yum install bzip2-........
This was unbelievable how much the Xen kernel slows things down, keep in mind both tests were done on the hostnode, one was with the Openvz-Xen hybrid kernel and the other was just OpenVZ. You can see the performance difference is nearly 300% better when not using the Xen kernel.
OpenVZ-Xen Kernel Test Results (I was wondering what was wrong/so slow with my Core i5!)
# # # # # #&n........
It's not just as simple as running the chroot command, you need to ensure the /proc and /dev entries are passed through and populated to the chroot environment.
Step 1 - Mount Your Off-lineOS
mount /dev/sda1 /mnt
Step 2 - Mount Proc
mount -t proc none /mnt/proc
Step 3 - Mount Dev
Most guides will tell you to use this: mount -o bind /dev /mnt//dev but that doesn't work for some reason in many cases:
mount: wron........
I took an educated guess because it kept happening at the same spot when loading the XP install. I thought it was the hard drive or motherboard.
But it turns out my heavily used but loved NEC 3500 DVD-RW drive was the culprit. After disconnecting it and swapping it for another much beloved Pioneer DVD-RW, everything has gone smoothly.
I never ran into this or many issues because I've hardly used this drive since moving it to another Desktop years ago. I actua........
This is a very simple solution, but most guides out there make you login twice (once to scp the key) and once to put the key in authorized_keys. There's no need for that.
If you don't already have a ~/.ssh/id_rsa.pub just type "ssh-keygen -t rsa" and keep hitting enter until it's done :)
Just use this code to easily enable passwordless login with SSHD
key=`cat ~/.ssh/id_rsa.pub`;ssh user@192.168.5.25 "echo $key >> ~/.ssh/auth........
I'm not a fan of Asus and won't be buying another because of having to fight Asus over a bogus warranty denial (it's a long story but they only replied about how to RMA my unit weeks later on the EXACT day the warranty expired).
Anyway, it's just a matter of hitting F9 to do this, there's no need to worry about booting from USB or CD (unless of course you want a different OS eg. Windows XP Pro, Vista/7, or a flavor of Linux or Unix). Also remember that you need to fully/properl........
CC drivers/message/fusion/mptsas.o
drivers/message/fusion/mptsas.c: In function `mptsas_port_delete':
drivers/message/fusion/mptsas.c:106: sorry, unimplemented: inlining failed in call to 'mptsas_set_rphy': function body not available
drivers/message/fusion/mptsas.c:462: sorry, unimplemented: called from here
make[3]: *** [drivers/message/fusion/mptsas.o] Error 1
make[2]: *** [drivers/message/fusion] Error 2
mak........
mdadm --assemble --scan
mdadm: /dev/md/diaghost05102010:2 has been started with 2 drives.
mdadm: /dev/md/diaghost05102010:1 has been started with 2 drives.
mdadm: /dev/md/diaghost05102010:0 has been started with 2 drives.
-bash-3.1# cat /proc/mdstat
Personalities : [linear] [raid0] [raid1] [raid6] [raid5] [raid4] [multipath]
md125 : active raid1 sda1[0] sdb1[1]
14658185 blocks super 1.2........
Seagate Inventory/Firmware Check
I heard about this issue a long time ago but never looked into it. I figured I wasn't affected since my 500GB drives were running for so long. I've been using Seagate's since 2002 and to this day all of the drives I have are alive from Seagate.
*Update the bad news is that I realize one of my 500GB's is about to die, it's not even a year old, but is also not affected by the recall according to Seagate!
Seagate Inventory/Firm........
From the package "parted" you can use the command "partprobe" to re-read the partition table. I really hate rebooting, and that's what Iloved to hear about AHCI motherboards, that they allow hotswap so you don't have to reboot. But that's only as good as the OS, if the OS does not reload the partition table you won't be able to do anything with that new drive you attached without rebooting. Yes, even without re-reading the partiton table Linux will........
Before we start I take no responsibility for this, you should have a backup and if you make a mistake during this process you could wipe out all of your data. So backup somewhere else before starting this as a precaution, or make sure it's data you could afford to lose.
The RAID 1 Setup (Hardware Wise)
I've already setup my 2 x 1TB (Seagate) drives with identical partitions, make sure your new hard drive (the empty one) is setup like your curr........
The binary "iostat" comes from the package "sysstat" and is available on all Linux/Unix like platforms.
Use the "-m" option to give you what you probably want, which is to see in MB/s how much bandwidth each disk is doing.
iostat -m
Linux 2.6.24.2 ((none)) 04/16/10
avg-cpu: %user %nice %system %iowait %steal %idle
........
I have no idea why but mkfs.ext3 defaults to a patheticlly small blocksize of 1024 bytes/1KB (kilobyte). That means the maximum filesize is ONLY 16GB! With 2KB/2048 bytes you get a 256 GB maximum filesize, and with 4KB/4096 bytes you get 2TB!
I finally noticed/paid attention to this after realizing that with rsync and scp that no file larger than 17GB could be transferred. I then realized it must be a file size limit on the partition.
Here is what tune2fs tol........
The folder I was trying to archive is about 72GB, but much like rsync at about 17GB it chokes because of the filesize. What's with so many common and essential Linux tools having such limitations? I guess it is likely that the authors never wrote their code with the idea that files would be so large but it's still very annoying. It's important to stay on top of these limitations on production servers because I didn't realize what happened until I checked the file with "........
In Debian based distros:
apt-get install jabber
Reading package lists... Done
Building dependency tree
Reading state information... Done
The following packages were automatically installed and are no longer required:
fakeroot dkms
Use 'apt-get autoremove' to remove them.
The following extra packages will be installed:
jabber-common
The following NEW packag........
I decided on using yum to help me decide even though I normaly use proftpd I decided to see what else I could find.
yum search ftp
Loaded plugins: fastestmirror
Loading mirror speeds from cached hostfile
* rpmforge: ftp-stud.fht-esslingen.de
* base: mirrors.netdna.com
* updates: updates.interworx.info
* addons: yum.singlehop.com
* extras: mirrors.netdna.com
rpmforge........
Codelite is a great choice and I intend on getting back into C++ development and I think Codelite is great being cross platform.
It looks like it was designed with a lot of thought and should do the job better. I really dislike the bloated and confusing IDE's from big companies like Microsoft where you usually have to use .NET and other useless technologies that just give Microsoft the advantage over you, the programmer, and the users.........
Here are the results, it is Sempron 3000+ AMD Mobile, 500Gig HDD, 512MB RAM with shared ATI Radeon graphics.
# # # # # # # ##### ###### # # #### # #
# # ## # # # #&nb........
PHP cannot access /usr/bin/opensslI have verified the username that runs the process is able to access /usr/bin/openssl and it does exist but the PHP script is saying it doesn't exist:
[code:1:1fd0f3abbe]
if (!file_exists($OPENSSL)) {
//echo "ERROR: OPENSSL $OPENSSL not foundn";
}[/code:1:1fd0f3abbe]
I don't get itI can clearly see the contents of /usr/bin by using the PHP system fu........
Mount Linux ext2 file systemNormally in Linux you could mount ext2 or ext3 etc... like this:
mount -t ext2 /dev/hda1 /mnt/hda1/
In FreeBSD the difference is of course the disk naming conventions (hda1 would be known a /dev/ad0s1):
To mount ext2 in FreeBSD just type:
mount -t ext2[b:68c16c60bf]fs[/b:68c16c60bf] /dev/ad0s1 /mnt/ad0s1........
Asterisk FreeBSD compile problemsI couldn't get it to compile without using the following options at compile time:
[b:b7d672ee28]
make install WITHOUT_ZAPTEL=YES WITHOUT_MYSQL=YES WITHOUT_FAX=YES WITHOUT_ODBC=YES WITHOUT_H323=YES[/b:b7d672ee28]Some problems you might have with copying over your Linux config files to FreeBSD is different paths.
[b:f044931f41]For example the etc path for Asterisk on BSD will now be:[/b:f044931f41]
[qu........
CentOS (most Linux) no-RAID to software RAID-1 guidehttp://lists.centos.org/pipermail/centos/2006-January/018624.html........
Nice General Linux RAID 1 GuideFull examples/tutorials that should work for any Linux system using GRUB or LILO as the boot loader.
This is the only tutorial I've seen that clearly shows how you can convert an existing non-RAID system to software RAID1 remotely, without ever having to be at the computer. This is important for people who co-locate or rent dedicated servers that they may not have physical access to in a timely manner.
https://alioth.debia........
Centos 4.3 x64 & VMWare Server Beta[code:1:6d0b2c8c2f]
The correct version of one or more libraries needed to run VMware Server may be
missing. This is the output of ldd /usr/bin/vmware:
linux-gate.so.1 => (0xffffe000)
libm.so.6 => /lib/tls/libm.so.6 (0xf7fbd000)
libdl.so.2 => /lib/libdl.so.2 (0xf7fb9000)
libpthread.so.0 => /lib/tls/libpthread.so.0 (0xf7fa7000)
libX11.so.6 => not f........
Setup Static IP Address ONBOOTAssuming you are using eth0
Note this will work for any version of CentOS and basically any version of Redhat Linux or Redhat based distribution.
You would need to create a new file
[code:1:02f8d34c30] /etc/sysconfig/network-scripts/ifcfg-eth0:0[/code:1:02f8d34c30]
DEVICE=eth0:0
the ":0" at the end specifies alias 0 we could actually change this to ":99" or "........
Updating yum repos for DAG /etc/yum.repos.dIn /etc/yum.repos.d
[quote:96456b2ab9]Create any file such as "CentOS-Dag.repo" in /etc/yum.repos.d[/quote:96456b2ab9]
Add the following to the above file:
[code:1:96456b2ab9]
[dag]
name=Dag RPM Repository For Red Hat Enterprise Linux
baseurl=http://dag.atrpms.net/redhat/el$releasever/en/$basearch/dag/
http://dag.freshrpms.net/redhat/e........
SSH Public Key Authentication (Login Without Passwords)I've gone over this before but just a quick note!
the "authorized_keys" file in ~/.ssh
must be chmodded to "600" or public key authentication won't work.
I guess it's kind of a security/failsafe feature that I've
seen on all Linux and Unix OS's........
Linux Unix Xorg X Server Intel Extreme i810 Graphics Problem(EE) I810(0): No Video BIOS modes for chosen depth.
(EE) Screen(s) found, but none have a usable configuration.
I have a new Dell PC with one of the latest Intel Extreme Graphics on-board crap. From what I can see any Linux/Unix/FreeBSD versions running XFree86 or Xorg from years ago or the latest version today will have this problem.
It's easily corrected FOR MOST people. Go into your........
Xorg fonts missing Xorg.0.logThis happened on a PCBSD installation but it could happen on any Unix/Linux Xorg installation:
If the text on your screen is too small and you're running at a high resolution if you do a
[code:1:04ca0d3455]cat /var/log/Xorg.0.log | more
[/code:1:04ca0d3455]
You'll see a bunch of fonts missing, specifically the 75dpi and 100dpi ones that you really need :)
(WW) The directory "/usr/X11........
Good Linux Security Tutorialhttp://www.freeos.com/articles/2829/2/13/........
FreeBSD Desktop OSsI would probably choose these over Linux.
In many ways these are probably more stable and just as easy to use as any Linux distros but the benefit of stable, updated and secure packages!
PC-BSD - http://www.pcbsd.org
DesktopBSD - http://www.desktopbsd.net/index.php?id=37
Personally PC-BSD is Beta at this point and is not easy if you are installing it on a non-primary partition.
I have not used Deskt........
Mounting NTFS in UnixJust a quick tutorial to mount your NTFS volumes in Unix (FreeBSD/Linux)
[quote:4a9de7bf80]mount -t ntfs -o umask=0 /dev/your_partition /mnt/your_mount_point[/quote:4a9de7bf80]
[b:4a9de7bf80]-o umask=0[/b:4a9de7bf80] is to ensure all users can access the mounted partition (otherwise don't use it and only root can access the mounted partition)
[b:4a9de7bf80]-t ntfs[/b:4a9de7bf80] is simple because it just lets mount kno........
PHP imagecreate() not found but compiled with GDHere is what I get:
[code:1:be41bc7717]
Fatal error: Call to undefined function: imagejpeg() in image.php on line 56
[/code:1:be41bc7717]
I am positive it is compiled with GD so I don't get the errorI need to install the linux-jpeg package
then
I need to recompil........
Bash Script Infohttp://www.faqs.org/docs/Linux-HOWTO/Bash-Prog-Intro-HOWTO.html#ss10.5
http://www.scit.wlv.ac.uk/~jphb/spos/notes/shell/shell5.html
http://quong.best.vwh.net/shellin20/#LtohTOCentry-41
http://www.cactus.org/~dak/shellscript.html
http://db.ilug-bom.org.in/Documentation/abs-guide/
http://pegasus.rutgers.edu/~elflord/unix/bash-tute.html
http://heather.cs.ucdavis.edu/~matloff/UnixAndC/Unix/CShellII.html
Since bash i........
Basic Port ListingHopefully someone finds this useful or at least interesting.
http://www.sans.org/top20/#u9
Name Port Protocol Description
Small services ........
Linux Security Mini-tutorialThis site has a good tutorial to get you started on securing your Linux system. Although I'm sure all of our systems are already 100% secure :lol:
http://www.yolinux.com/TUTORIALS/LinuxTutorialInternetSecurity.html........
Clustering LinksI thought this might be interesting for people with spare time.
[b:6423c19973]Great clustering article from Linux Mag[/b:6423c19973]
http://www.linux-mag.com/2003-11/clusters_01.html
[b:6423c19973]General Linux cluster information[/b:6423c19973]
http://www.gdargaud.net/Hack/ClusterNotes.html#HighA
http://www.faqs.org/docs/Linux-HOWTO/Cluster-HOWTO.html#s3
http://www.yolinux.com/TUTORIALS/LinuxClustersAndFileSys........
gnuCash is available for all main platforms, Linux/Unix, MacOS (FreeBSD anyway), and Windows.
You can download gnuCash free from here.
It does seem to be fairly full featured and somewhat straight forward, but like so many programs it is missing a few key features or things don't work quite right.
It doesn't support importation of CSV files, which is a big minus. And the developers rather than wanting to add support have just dec........
*This is a bug with initramfs support, all kernels after around 2.6.27.54 suffer from this problem.
If you try to include initramfs into your kernel (I mean actually building your binaries into the kernel) this will always happen. Obviously some code has changed in recent kernels that is present in all new kernels, it makes it impossible to boot
I've tried the latest 2.6.32, 2.6.33, 2.6.34, 2.6.35, 2.6.36, 2.6.37, 2.6.38 kernels and they all do this. I found one bug re........
Linux Kernel v2.6.30.3
102220 blocks
CHK include/linux/version.h
CHK include/linux/utsrelease.h
SYMLINK include/asm -> include/asm-x86
CALL scripts/checksyscalls.sh
CHK include/linux/compile.h
CC drivers/net/igb/igb_main.o
drivers/net/igb/igb_main.c: In function `igb_up':........
I have played around with Pound a little bit. It is a reverse proxy and load balancer in one, and it can be used as only a reverse proxy if you like. It is very simple to configure as either, and Pound even senses if one of the systems is down and stops sending requests to the dead server.
It supports SSL (but passes the request to the destination server unencrypted) and even the Apache log format. Pound is very simple, fast a........
The "Geoip" package is available on virtually all Linux and Unix like systems and is very handy in looking an IP address' corresponding country.
The homepage of the maintainers is here.
They also have a package called "Geocity" which can be downloaded from their site, it is still free and gives you a close indication of the city the visitor is from. You can........
Shortcut/Easiest Way To Create A Self-Signed Key:
openssl req -new -x509 -nodes -days 1530 -out server.crt -keyout server.key
Using the above, you instantly create a self-signed certificate valid for 1530 days and you can simply skip to step #5.) below.
If You Need a Real SSLCertificate (eg. Equifax/Openssl) then you need to create a CSR request (you'll need to follow Steps 1.) and 2.) in order to create the CSR. You then upload the CSR Certi........
top - 09:34:12 up 2 days, 20:57, 2 users, load average: 1.83, 1.99, 2.03
Tasks: 59 total, 2 running, 57 sleeping, 0 stopped, 0 zombie
Cpu(s): 0.3%us, 0.0%sy, 0.0%ni, 0.0%id, 99.7%wa, 0.0%hi, 0.0%si, 0.0%st
That 99.7% wa is iowait, it means the server is waiting for a process to complete an IOoperation or in plain English, there is a delay in........
I didn't find any useful information that actually fixed this. My VPS was in the "Running State" and I could not stop or restart it. I kept getting "Container already locked" no matter what Idid (I tried all the suggestions in the Google results for this error).
Most of the suggestions were for Windows but I only use Linux. The other solutioins also said to restart the VZ service or even the entire hostnode and this was not acceptable to me........
It's a bit of a pain that many basic third party tools that aren't put of the main Centos/RHEL repositories are not available unless you compile them or install the RPMForge Repo.
*Updated 08/29 with new download location changed from apt.sw.be to rpmforge.sw.be
Here's a quick, simple/cut&paste way to do it:
wget http://rpmforge.sw.be/redhat/el5/en/i386/rpmforge/RPMS/rpmforge-release-0.5.1-1.el5.rf.i386.rpm
rpm -i rpmforge........
There is a nice mode that Samba supports which you can add to smb.conf
create mode=555
This way users can create and write files/directories without deleting (except I believe dirs can be deleted but only if there are no files inside).
It's too bad that Linux does not have built-in "write"/"delete" privileges and is something that even Windows 98 can trump.........
You can see the problem below, GRUB recognizes my hard drive and sees the partitions but cannot access them. This is from the GRUB boot disc I'm using.
What happened is that I had some power issues causing this system's power to be interrupted several times and basically an on/off on/off situation.
The system won't boot, I just get a flashing cursor and no message or error from GRUB. Obviously the problem is that my MBR seems corrupt or some other issue.
My........
You might remember my original GluserFS/OpenVZ benchmark which produced a horrible 29.8
This is the exact same system, but using the latest 2.0.8 (with some small files patch which speeds up performance) you can see it is about 25% faster.
I also haven't tuned my config files at all, but there are some settings that should increase performance on small files which I believe i........
Inever saved any of the logs, but basically no matter what OS (Linux)I used, I could not get my 1000GB hard drive to work (Seagate SATA). The BIOS recognizes the drive and fdisk -l shows the hard drive as it should.
The tricky thing is that different OS's will give you different results, but don't be fooled. You can't use these larger drives for long. Iwas getting all kinds of seek/IOerrors and also messages that the port could not be read.........
This is very disappointing since GlusterFS markets itself as a solution to deploy VPS servers on. On the HNitself I get a Unixbench of about 360.
I'm also using an SSH tunnel to secure the communications, but even before that, things seemed very slow.
# # # # # # # #####&n........
In those 4 simple commands you can setup mutual key exchange between two sshservers by using a single login shell session and single window.
*Just change the IP address examples of (10.10.0.2) to the target of your mutual key exchange. It doesn't matter if the server is on a LANor WAN(well unless the server is behind a firewall and you cannot SSHinto it).........
Iwas getting really annoyed with this, I used full quotes around the filename and vi, cat, less all thought I was trying to pass the dash in the filename as an argument.
I didn't realize that all you have to do is just put a dash dash "--"in front.
Here's an example:cat -- "-etc-glusterfs-glusterfsd.vol.log"
Without the -- you get: cat: invalid option -- c
Try `cat --help' for more information.
Ih........
In Newer Linux Distros This Way Is Easiest and works on newer versions like Ubuntu, Mint, Fedora, Centos, Debian etc.
#if you are missing timedatectl this in newer distros like Ubuntu/Mint/Debian and are using a container like Docker then do "apt install systemd"
timedatectl set-timezone America/Vancouver
Replace the America/Vancouver with the correct timezone.
To see the list you can just type "timedatectl set........
For some reason Ikeep getting this error when trying to run a sudo command eg:
sudo -u someuser somecommand
sudo: Error dropping capabilities, aborting
My version of sudo is:sudo-1.6.9p17-3.el5_3.1 and I've heard that version 1.7 fixes everything. The only thing is yum does not think sudo has any update. Iguess the new version has not been committed to the RPM repository yet.
This is really a huge and ann........
A VPS Server I had just wasn't working right, code that I migrated there just wasn't working. For example, it kept telling me the connection to the database was unsuccessful, halfway through iterating through results it already had.
Then I realized it wasn't my code. Ichecked my /proc/user_beancounters and found this:
cat /proc/user_beancounters
Version: 2.5
uid resource held maxheld barrier limit failcnt........
It's actually very simple and "grep" makes it as easy as possible. I'll outline a few common scenarios and provide some examples.
Say you want to search ALLfiles within the current directory (and inside/deeper) for the text "phpinfo()"
grep -R "phpinfo()" *
If you want to search only certain files such as only .txt you would do this instead:
grep -R "phpinfo()" *.txt
As you ca........
This is something that annoys a lot of people, fortunately the Redhat style OS's are the most simple in this respect. I disagree that Debian's way makes sense, it is more of a hackish approach in how they implement iptables.
Anyway, for those who are using Redhat/Centos style OS's it is very simple.
Set your rules from the shell/command prompt and to save the iptables firewall rules so they are remember/loaded on boot just run this command:
service iptables........
There is a tool called "xml2" which will parse both HTML and XML scripts, this is very useful to do a mass extraction or conversion of data based on say an HTML table etc..
It becomes even more powerful using bash if certain tags are identified with a certain class="" attribute or something else unique to only the tags you want.
Happy parsing.........
First of all, the iPhone is crippled in many ways, but most of my complaints about functionality have been addressed through the jailbreak, Ican run apps in the background of my choosing, I can install a terminal, acccess my phone through SSH and SCP and so much more.
It even addresses the 15 minute e-mail problem, I installed a program called "PushMod" and now set the checking time to just 1 minute.
Apple should really thank the developers for this gift, it ma........
Apple crippled the iPhone by not allowing multi-tasking of the non-primary apps. I use SSH a lot and I don't want to close my session just to check my e-mail, etc, now an app found in Cydia called "Backgrounder" allows just that.
Although it's not perfect, we installed the correct one for "3.x" iPhones and hit "Reload SpringBoard" and the hour/circle glass has just been going for minutes.
It seems like it installed fine even with the crash t........
Truly, the only way to unleash the capabilities and customization abilities of iPhone are to jailbreak, it's not just for hackers anymore.
A few days ago someone by the named of "geohot" released a single click application called "purplera1n", which does the entire operation smoothly and seamlessly.
In our case, the first time it went as far as "done, wait for reboot" on our Windows machine and for minutes we waited and saw the pic on the iPhone w........
Yes, Iadmit I finally got bitten by the hype as much as I can usually see through it all. Keep in mind this review is of the "stock" phone, no jailbreaking yet which is what really unleashes the customizability and whyI bought iPhone.
I had better things to say about this phone before buying it, and it is a great phone, perhaps the best on the market by far, if not because of the Mac OS port onto the iPhone and all the apps, etc, etc.
With that said........
I kind of expected this feature to be there in some form, to stay ahead of the pack Apple needs to stay on top of this. User's of HTC's Android smart phone which uses a Linux based OS with Google's power behind it, note that you can save passwords in the browser on that phone.
Apple needs to continuously evaluate the needs in its core apps and make sure the features are cutting edge and top notch, if other phones come out with some of these seemingly small but essential features........
Iused to get all kinds of weird annoying characters like "" during compilation with gcc especially.
example:
dmg2img.c:456: error: BZ_OK undeclared (first use in this function)
dmg2img.c:471: warning: implicit declaration of function BZ2_bzCompressEnd
dmg2img.c:482: warning: implicit declaration of function BZ2_bzDecompress
dmg2img.c:484: error: BZ_PARAM_ERROR undecl........
The dmg format is silly and annoying to work with, why couldn't Apple stick with the .iso standard? Anyway, there's an excellent Linux and Windows based tool to convert it back to a normal .iso Image called dmg2iso
I'll only cover theLinux version although the Windows pre-built binary works the same way.
Download dmg2iso here for free (from the author's website)
It's just silly and doesn't make sense that Ubuntu doe........
I've had an old Blackberry for a few years and I was ready to spend some serious cash on a nice Nokia. I love the idea of the Linux based Symbian S60 OS, so I was looking at phones like the E63, E71 (both are basically the same, at least CPU/screensize although E71 is thinner, has a 3MP camera, has GPS, and has dedicated buttons to adjust the volume).
Then Iheard about the N97 and what a revolution it was supposed to be and it was even compared to iPhone.
To........
Server not using user level security and no password supplied.
tree connect failed: NT_STATUS_WRONG_PASSWORD
That happens when trying to use smbclient to connect to a share. The weird thing is that I can authnenticate just fine from Windows XP.
It is partially my mistake, I forgot this share does have a password. I've tried authenticating with the correct user and also with "Guest" because this works in Windows. In Linux I ........
There's a lot of information and guides on OCFS2 for RHELand Centos Linux but the package setup and configuration is slightly different and this has thrown some people off.
Installing OC2FS
You should install the following packages to get started:
apt-get install ocfs2-tools ocfs2console
Configure OC2FS
In RHEL/Centos the main configuration file is located in /etc/sysconfig/o2cb
However in Debian based Linux it is located........
This will give you the basic info needed to browse and connect to Samba shares from the command line. From the GUI of Gnome or KDE etc, it is pretty standard and straight forward. However, I've found very little guides on how to do it from the command line and if you're like me, a nerd who prefers command line for its simplicity and for remote use, this is the way to go.
First get a list of all the Samba/SMB shares on the target.
smbclient -L hostname........
There's a lot of outdated information and confusion for system administrator's out there.
One annoying task for many an Administrator has been backing up data in Linux. You don't need any GUI tools such as K3B or GnomeBaker. Both are excellent tools but for veteran command line users working remotely, using the keyboard is a great and possibly automated way to save yourself pain and hassle.
At a later date we'll cover how scripting can automatically backup certain........